Idler Power Research Articles

Quasi-phase-matched DC-induced three wave mixing versus four wave mixing: a simulated comparison

A comparison is made between DC-induced three-wave mixing under an on-off quasi-phase-matching scheme and a perfectly phase-matched four wave mixing process. It is shown that the DC-induced process is capable of producing a significantly larger conversion efficiency than the four wave mixing process. Despite the fact that it suffers greater effects of dispersion, the enhanced growth rate of the DC-induced process provides a conversion efficiency roughly 300× larger than that of four wave mixing. Over a sample length of 20 cm the DC-induced process is able to generate idler power more than 270 times greater than that produced by the equivalent four wave mixing process.

High-power, high repetition-rate, green-pumped, picosecond LBO optical parametric oscillator

We report on a picosecond, green-pumped, lithium triborate optical parametric oscillator with record-high output power. It was synchronously pumped by a frequency-doubled (530 nm), pulse-compressed (4.4 ps), high-repetition-rate (230 MHz), fiber-amplified gain-switched laser diode. For a pump power of 17 W, a maximum signal and idler power of 3.7 W and 1.8 W was obtained from the optical parametric oscillator. A signal pulse duration of ~3.2 ps was measured and wide tunability from 651 nm to 1040 nm for the signal and from 1081 nm to 2851 nm for the idler was achieved.

Cascaded continuous-wave singly resonant optical parametric oscillator pumped by a single-frequency fiber laser

We present a cascaded continuous-wave singly resonant optical parametric oscillator (SRO) delivering idler output in mid-IR and terahertz frequency range. The SRO was pumped by an ytterbium-doped fiber laser with 27W linear polarization pump powers, and based on periodically poled MgO:LiNbO3 crystal (PPMgLN) in two-mirror linear cavity. The PPMgLN is 50mm long with 29.5μm period. The idler power output at 3811nm was obtained 2.6W. The additional spectral components that have been attributed to cascaded optical parametric processes are described at increasing pump levels. Besides the initial signal component at about 1476.8nm, further generated wavelengths with frequency shifts about 47cm−1, 94cm−1 and 104cm−1 were observed. It was speculated that the idler waves lie in the terahertz (THz) domain from the observed results.

Theoretical and experimental studies on output characteristics of an intracavity KTA OPO

An acousto-optically Q-switched Nd:YVO(4)/KTiOAsO(4) (KTA) intracavity optical parametric oscillator (OPO) is efficiently realized in singly resonated scheme. With an end-pumping diode power of 25.9 W, output signal (1535 nm) power of 3.77 W and idler power (3467 nm) of 1.18 W are obtained at a pulse repetition rate of 50 kHz. A rate-equation model is set up to simulate the output power and time characteristics of both signal and idler waves. And both the numerical and experimental results show that the idler pulse width is shorter than the signal one in a singly resonant OPO.

基于闲频光功率的光纤参量振荡器反馈控制实验

基于闲频光功率的光纤参量振荡器反馈控制实验

High-power, fiber-laser-pumped, picosecond optical parametric oscillator based on MgO:sPPLT

We report a stable, high-power, mid-infrared synchronously-pumped optical parametric oscillator (SPOPO) based on MgO:sPPLT, pumped by a 1064 nm, picosecond Yb-fiber laser operating at a repetition rate of 81.1 MHz. The singly resonant SPOPO is tunable over 1531-1642 nm (111 nm) in the near-infrared signal and 3022-3488 nm (466 nm) in the mid-infrared idler, providing a total tuning range of 577 nm. Careful optimization of output coupling results in a signal output power as high as 4.3 W at 1593 nm and a mid-infrared idler power of 2 W at 3204 nm for 13.4 W of pump power at a total extraction efficiency of 47%. The SPOPO can be operated near room temperature, down to 30 °C, and exhibits passive peak-to-peak power stability better than 8.6% at 1568 nm (signal) and 8.2% at 3310 nm (idler) over 13 hours at full power. The output signal pulses have duration of 17.5 ps, with a FWHM spectral bandwidth of 1.4 nm centered at 1568 nm.

12 W mid-infrared output, singly resonant, continuous-wave optical parametric oscillator pumped by a Yb3+-doped fiber amplifier

We report a continuous-wave singly resonant optical parametric oscillator (SRO) with more than 12 W of idler power at 3414 nm when it was operated at 30°C. The SRO was directly pumped by a single-frequency, ytterbium-doped fiber laser with 49 W linear polarization pump powers, and based on 50 mm long periodically poled MgO:LiNbO3 crystal (PPMgLN) in two-mirror linear cavity with 30.5 μm grating period. It’s pump power at threshold was 5.4 W. The slope-efficiency and quantum-limited performance reached 26 and 79.2%, respectively. The beam polarization matched the e → e + e interaction in crystal. The idler waves were temperature tuned in the range of 3654 to 3811 nm and 3248 to 3414 nm based on two 50 mm long PPMgLN with 29.5 and 30.5 μm grating period. To the best of our knowledge, this is the highest continuouswave mid-IR output obtained for a fiber laser pumped optical parametric oscillator (OPO).

High-power, continuous-wave, mid-infrared optical parametric oscillator based on MgO:sPPLT

We report a stable, high-power, cw, mid-IR optical parametric oscillator using MgO-doped stoichiometric periodically poled LiTaO₃ (MgO:sPPLT) pumped by a Yb fiber laser at 1064 nm. The singly resonant oscillator (SRO), based on a 30 mm long crystal, is tunable over 430 nm from 3032 to 3462 nm and can generate as much as 5.5 W of mid-IR output power, with >4 W of over 60% of the tuning range and under reduced thermal effects, enabling room temperature operation. Idler power scaling measurements at ~3.3 μm are compared with an MgO-doped periodically poled LiNbO₃ cw SRO, confirming that MgO:sPPLT is an attractive material for multiwatt mid-IR generation. The idler output at 3299 nm exhibits a peak-to-peak power stability better than 12.8% over 5 h and frequency stability of ~1 GHz, while operating close to room temperature, and has a linewidth of ~0.2 nm, limited by the resolution of the wavemeter. The corresponding signal linewidth at 1570 nm is ~21 MHz.

High efficiency KTiOAsO4 optical parametric oscillator within a diode-side-pumped two-rod Nd:YAG laser

A high efficiency KTiOAsO4(KTA) intracavity optical parametric oscillator (IOPO) is demonstrated within a diode-side-pumped acousto-optically (AO) Q-switched two-rod Nd:YAG laser. With a 25-mm-long X-cut KTA crystal, efficient parametric conversions to signal (1.54 μm) and idler (3.47 μm) waves are realized. The highest output power of 15.8 W including 12.7 W signal and 3.1 W idler power is obtained at a repetition rate of 7.5 kHz and a pump power of 208 W, corresponding to an optical-to-optical conversion efficiency of up to 7.6%. The signal pulse duration is 32 ns with a peak power of 53 kW. At a repetition rate of 12.5 kHz and the pump power of 208 W, the highest idler power of 3.4 W is obtained with a peak power of 14 kW and a pulse duration of 19 ns. And the beam quality factors (M2) of the signal and idler waves are determined to be around 2 and 20, respectively.

Fiber-laser-based green-pumped continuous-wave singly-resonant optical parametric oscillator

Stable, high-power, second-harmonic-generation (SHG) of a compact CW Ytterbium (Yb) fiber laser at 1064 nm into the green and its use as a pump source for CW singly-resonant optical parametric oscillator (SRO) is demonstrated. Using a simple single-pass SHG configuration in MgO:sPPLT, as much as 9.6 W of single-frequency green radiation at 532 nm is generated from 30 W of fundamental power at a conversion efficiency of 32.7% in a Gaussian spatial profile with a beam quality factor of M2 < 1.3. Thermal effects have been investigated at different fundamental power levels and various thermal management schemes are employed to maximize the second-harmonic power. The green source is successfully deployed to pump a CW SRO tunable over 855–1408 nm, generating up to 2.1 W of idler at 1168 nm. The peak-to-peak idler power stability is better than 10.7% over 40 min, with beam quality factor M2 < 1.26 for the idler and M2 < 1.52 for the signal.

Optical parametric generation in CdSiP_2

We report efficient generation of picosecond pulses in the near- and mid-IR in the new nonlinear material CdSiP(2) pumped at 1.064 μm by an amplified mode-locked Nd:YVO(4) laser at a 100 kHz repetition rate. By using single-pass optical parametric generation in 8-mm-long crystal cut for type I(e→oo) noncritical phase matching, an average idler power of 154 mW at 6.204 μm together with 1.16 W of signal at 1.282 μm has been obtained for 6.1 W of pump at photon conversion efficiencies of 15% and 23%, respectively. Signal pulse durations of 6.36 ps are measured for 9 ps pump pulses.

Efficient, high-power, ytterbium-fiber-laser-pumped picosecond optical parametric oscillator

We report a high-power picosecond optical parametric oscillator (OPO) synchronously pumped by a Yb fiber laser at 1.064 μm, providing 11.7 W of total average power in the near to mid-IR at 73% extraction efficiency. The OPO, based on a 50 mm MgO:PPLN crystal, is pumped by 20.8 ps pulses at 81.1 MHz and can simultaneously deliver 7.1 W of signal at 1.56 μm and 4.6 W of idler at 3.33 μm for 16 W of pump power. The oscillator has a threshold of 740 mW, with maximum signal power of 7.4 W at 1.47 μm and idler power of 4.9 W at 3.08 μm at slope efficiencies of 51% and 31%, respectively. Wavelength coverage across 1.43-1.63 μm (signal) and 4.16-3.06 μm (idler) is obtained, with a total power of ~11 W and an extraction efficiency of ~68%, with pump depletion of ~78% maintained over most of the tuning range. The signal and idler output have a single-mode spatial profile and a peak-to-peak power stability of ±1.8% and ±2.9% over 1 h at the highest power, respectively. A signal pulse duration of 17.3 ps with a clean single-peak spectrum results in a time-bandwidth product of ~1.72, more than four times below the input pump pulses.

Optimally-output-coupled, 17.5 W, fiber-laser-pumped continuous-wave optical parametric oscillator

We present a stable, high-power, fiber-laser-pumped, continuous-wave (cw), singly resonant optical parametric oscillator (SRO) for the mid-infrared in an output-coupled (OC) configuration, providing 17.5 W of total output power at 61% extraction efficiency. Using a single-frequency, cw Yb fiber laser at 1064 nm and a 50-mm-long MgO:PPLN crystal, through optimization of signal output coupling we generate up to 9.8 W of signal power in the near-infrared together with 7.7 W of idler power for 28.6 W of pump, while in the absence of output coupling, 8.6 W of idler power is generated for the same pump power at 30% efficiency. The SRO is tunable over 360 nm in the idler range. The deployment of signal output coupling results in a total tuning of 513 nm (120 nm of signal, 393 nm of idler) over which watt-level output power can be extracted. Through careful control of thermal effects we achieve a long-term peak-to-peak idler power stability of 5% over 14 hours near room temperature. The output beams have TEM00 spatial profile with M 2<1.28 for the idler and M 2<1.37 for the signal.

One-Watt level mid-IR output, singly resonant, continuous-wave optical parametric oscillator pumped by a monolithic diode laser

We report more than 1.1 Watt of idler power at 3373 nm in a singly resonant optical parametric oscillator (SRO), directly pumped by a single-frequency monolithic tapered diode laser. The SRO is based on a periodically poled MgO:LiNbO3 crystal in a four mirror cavity and is excited by 8.05 W of 1062 nm radiation. The SRO pump power at threshold is 4 W. The internal slope-efficiency and conversion efficiency reach 89% and 44% respectively. The signal and idler waves are temperature tuned in the range of 1541 to 1600 nm and 3154 to 3415 nm respectively. To the best of our knowledge, this is the highest output obtained for a diode pumped optical parametric oscillator (OPO), and the first time a SRO is directly pumped by a monolithic tapered diode laser.

A pump-resonant signal-resonant optical parametric oscillator for spectroscopic breath analysis

We report on a widely tunable continuous-wave single-frequency pump-resonant signal-resonant optical parametric oscillator (PRSRO) delivering 20 mW to 50 mW of idler power spanning an octave bandwidth in the mid-infrared (1.7 µm and 3.5 µm). The PRSRO is pumped by a Ti:Al2O3 ring laser delivering 760 mW around λ p =795 nm, and thanks to the pump enhancement a threshold as low as 110 mW is achieved with a multi-grating temperature-tuned MgO-doped periodically-poled LiNbO3. This PRSRO will be used for multi-species trace gas sensing based on cavity ring-down spectroscopy.

Nd:YAG pumped nanosecond optical parametric oscillator based on LiInSe_2 with tunability extending from 47 to 87 μm

LiInSe(2) is one of the few (only 5) non-oxide nonlinear optical crystals whose band-gap (2.86 eV) and transparency allowed in the past nanosecond optical parametric oscillation in the mid-IR without two-photon absorption for a pump wavelength of 1064 nm. However, the first such demonstration was limited to the 3.3-3.78 microm range for the idler and the average idler power did not exceed 2.5 mW. Here we report broadly tunable operation, from 4.7 to 8.7 microm, of an OPO based on LiInSe(2), achieving maximum idler pulse energy of 282 microJ at approximately 6.5 microm, at a repetition rate of 100 Hz (approximately 28 mW of average power).

Stable, continuous-wave, intracavity, optical parametric oscillator pumped by a semiconductor disk laser (VECSEL)

We report relaxation oscillation free, true continuous-wave operation of a singly-resonant, intracavity optical parametric oscillator (OPO) based upon periodically-poled, MgO-doped LiNbO3 and pumped internal to the cavity of a compact, optically-excited semiconductor disk laser (or VECSEL). The very short upper-laser-state lifetime of this laser gain medium, coupled with the enhancing effect of the high-finesse pump laser cavity in which the OPO is located, enables a low threshold, high efficiency intracavity device to be operated free of relaxation oscillations in continuous-wave mode. By optimizing for low-power operation, parametric threshold was achieved at a diode-laser power of only 1.4 W. At 8.5 W of diode-laser power, 205 mW of idler power was extracted, indicating a total down-converted power of 1.25 W, and hence a down-conversion efficiency of 83%.

High repetition rate mid-infrared generation with singly resonant optical parametric oscillator using multi-grating periodically poled MgO:LiNbO 3

A high repetition rate mid-infrared singly resonant optical parametric oscillator (OPO) using MgO-doped multi-grating periodically poled LiNbO 3 (MgO:PPLN) is demonstrated. A 1064 nm Q-switched Nd:YVO 4 laser at 10 kHz repetition rate and pulse width of 17.8 ns was used to pump the OPO. The period of the quasi-phase matched (QPM) grating in the multi-grating MgO:PPLN chip varied from 25.5 to 31.5 μm in steps of 0.5 μm. This corresponds to the generation of a signal beam from 1.37 to 1.64 μm and an idler beam from 3.0 to 4.8 μm, respectively. A maximum signal power of 250 mW and idler power of 140 mW has been obtained with an input pump beam of power 1.92 W, for a grating period of 30.5 μm. A maximum optic–optic conversion efficiency of 20% and 7.4% in the idler has been observed. It has been observed that the output power increases as the period of the grating increases.

Stimulate Brillouin Scattering Based Broadband Tunable Slow-Light Conversion in a Highly Nonlinear Photonic Crystal Fiber

An integrated configuration is proposed to convert tunable slow light from signal to another frequency in a wide bandwidth by using a 70 m-long highly nonlinear photonic crystal fiber (HN-PCF). A 10 GHz RZ signal is delayed by a 10 Gbit/s 231-1 pseudo random bit sequence (PRBS) stimulated Brillouin scattering (SBS) pump, and the slow light is converted to another frequency in a broadband by four-wave mixing (FWM). By this way, not only the slow light is converted, but the idler power is enhanced greatly. In our experiment, all-optical controlled 37.5 ps delay time is converted in a 40 nm bandwidth flatly, and 4.7 dB idler power is enhanced simultaneously. The experimental results are in good agreement with those of the theory.

Pump-enhanced difference-frequency generation at 33 μm

The demonstration of continuous wave intracavity difference-frequency generation in the mid-infrared (mid-IR) is presented. A cavity for pump laser enhancement is constructed around a periodically poled lithium niobate crystal, and the cavity length is locked to the frequency of the pump laser using the Pound-Drever-Hall technique, producing a gain of 12 in the resultant idler power compared to the single-pass case. A widely tunable single-mode 3.3 microm idler beam with a power of nearly 10 mW is available for direct absorption spectroscopy. The pump-enhancement method demonstrated here should be readily scalable to produce hundreds of milliwatts of mid-IR light by using higher power signal and pump lasers.