Sulfate Hydrate Research Articles

Birnbaum-Saunders Durability Life Prediction Model of Site-Exposed Concrete in the Saline Soil Area

Aiming at the prominent problem of short durability life of concrete in saline soil area and the shortcomings of indoor accelerated test, an outdoor field exposure test was designed. The concrete specimens were semiburied in the Tianshui area with salinized soil characteristics, and nondestructive testing was conducted every 180d (days). The durability evaluation parameters and mechanical performance indexes were selected for macroscopic analysis, and the corrosion mechanism was analyzed by using the SEM image and the XRD phase. The Birnbaum-Saunders model based on physical failure and probability statistics was used for life prediction. The results show that there are rod-shaped and chip-shaped crystals growing from the surface of the gel and the internal holes in the exposed end and the embedded end of the concrete. However, the damage and deterioration of the buried end are more serious than those of the exposed end. The corrosion products mainly included ettringite, gypsum, calcium carbonate, sodium sulfate hydrate, carbosilite, and Friedel’s salt. The reliability life curve based on the Birnbaum-Saunders model can describe the whole process of exposed concrete from damage accumulation to failure. In addition, the dynamic modulus degradation index is more sensitive to concrete durability damage, and the life obtained by the Birnbaum-Saunders model is shorter than the quality degradation index. The life obtained by this degradation index is taken as the life of the concrete exposed in the saline soil site, and the concrete life of C30, C40, and C50 is about 3340d, 3930d, and 4360d, respectively.

Laboratory exploration of mineral precipitates from Europa's subsurface ocean.

The precipitation of hydrated phases from a chondrite-like Na-Mg-Ca-SO4-Cl solution is studied using in situ synchrotron X-ray powder diffraction, under rapid- (360 K h-1, T = 250-80 K, t = 3 h) and ultra-slow-freezing (0.3 K day-1, T= 273-245 K, t = 242 days) conditions. The precipitation sequence under slow cooling initially follows the predictions of equilibrium thermodynamics models. However, after ∼50 days at 245 K, the formation of the highly hydrated sulfate phase Na2Mg(SO4)2·16H2O, a relatively recent discovery in the Na2Mg(SO4)2-H2O system, was observed. Rapid freezing, on the other hand, produced an assemblage of multiple phases which formed within a very short timescale (≤4 min, ΔT = 2 K) and, although remaining present throughout, varied in their relative proportions with decreasing temperature. Mirabilite and meridianiite were the major phases, with pentahydrite, epsomite, hydrohalite, gypsum, blödite, konyaite and loweite also observed. Na2Mg(SO4)2·16H2O was again found to be present and increased in proportion relative to other phases as the temperature decreased. The results are discussed in relation to possible implications for life on Europa and application to other icy ocean worlds.

Exploration of the structural, spectroscopic and thermal properties of double sulfate monohydrate NaSm(SO4)2·H2O and its thermal decomposition product NaSm(SO4)2

Samarium-sodium double sulfate crystalline hydrate NaSm(SO4)2·H2O was obtained by the crystallization from an aqueous solution containing equimolar amounts of ions. The anhydrous salt of NaSm(SO4)2 was formed by a thermally induced release of the equivalent of water from NaSm(SO4)2·H2O. The kinetic parameters of thermal decomposition were determined (Ea = 102 kJ/mol, A = 9·106). The crystal structures of both compounds were refined from the X-ray powder diffraction data. Sulfate hydrate NaSm(SO4)2·H2O crystallizes in the trigonal symmetry, space group P3121 (a = 6.91820(3) and c = 12.8100(1) Å, V = 530.963(7) Å3). The anhydrous salt crystallizes in the triclinic symmetry, space group P-1 (a = 6.8816(2), b = 6.2968(2) and c = 7.0607(2) Å, α = 96.035(1), β = 99.191(1) and γ = 90.986(1)°, V = 300.17(1) Å3). The vibrational properties of compounds are mainly determined by the sulfate group deformations. The luminescence spectra of both sulfates are similar and are governed by the transitions of samarium ions 4G5/2 → 6HJ (J = 5/2, 7/2, 9/2 and 11/2). The anhydrous sulfate is stable up to 1100 K and undergoes an almost isotropic expansion when heated. After 1100 K, the compound decomposes into Sm2(SO4)3 and Na2SO4.

An Experimental Study on Mechanical Properties for the Static and Dynamic Compression of Concrete Eroded by Sulfate Solution.

The mechanical properties of the static and dynamic compression of concrete eroded by a 15% sodium sulfate solution were explored with a 70-mm-diameter true triaxial static-dynamic comprehensive loading test system, and an analysis of the weakening mechanisms for the degree of macroscopic damage and microscopic surface changes of eroded concrete were conducted in combination with damage testing based on relevant acoustic characteristics and SEM scanning. The experience obtained in this paper is used to analyze and solve the problem that the bearing capacity of concrete buildings is weakened due to the decrease in durability under the special conditions of sulfate erosion. The results showed that, in a short time, the properties of concrete corroded by sulfate solution were improved to a certain extent due to continuous hydration. When the corrosion time was prolonged, the internal concrete structure was destroyed after it was eroded by sulfate, and its dynamic and static strength, deformability, and energy absorption were reduced to differing degrees, thus greatly inhibiting the overall mechanical performance of concrete; the dynamic compressive strength changed with strain that exhibited a significant strain rate effect; and, under the influence of sulfate erosion and hydration, the longitudinal wave velocity increased first and then decreased. The longitudinal wave velocity was slower than that of concrete under normal environment and distilled water immersion condition. SEM and acoustic wave analysis indicated that the internal concrete structure was destroyed after it was eroded by sulfate, and its dynamic and static strength, deformability, and energy absorption were reduced to differing degrees, thus greatly inhibiting the overall mechanical performance of concrete.

Crystal Structure, Vibrational, Spectroscopic and Thermochemical Properties of Double Sulfate Crystalline Hydrate [CsEu(H2O)3(SO4)2]·H2O and Its Thermal Dehydration Product CsEu(SO4)2

Crystalline hydrate of double cesium europium sulfate [CsEu(H2O)3(SO4)2]·H2O was synthesized by the crystallization from an aqueous solution containing equimolar amounts of 1Cs+:1Eu3+:2SO42− ions. Anhydrous salt CsEu(SO4)2 was formed as a result of the thermal dehydration of the crystallohydrate. The unusual effects observed during the thermal dehydration were attributed to the specific coordination of water molecules in the [CsEu(H2O)3(SO4)2]·H2O structure. The crystal structure of [CsEu(H2O)3(SO4)2]·H2O was determined by a single crystal X-ray diffraction analysis, and the crystal structure of CsEu(SO4)2 was obtained by the Rietveld method. [CsEu(H2O)3(SO4)2]·H2O crystallizes in the monoclinic system, space group P21/c (a = 6.5574(1) Å, b = 19.0733(3) Å, c = 8.8364(2) Å, β = 93.931(1)°, V = 1102.58(3) Å3). The anhydrous sulfate CsEu(SO4)2 formed as a result of the thermal destruction crystallizes in the monoclinic system, space group C2/c (a = 14.327(1) Å, b = 5.3838(4) Å, c = 9.5104(6) Å, β = 101.979(3) °, V = 717.58(9) Å3). The vibration properties of the compounds are fully consistent with the structural models and are mainly determined by the deformation of non-rigid structural elements, such as H2O and SO42−. As shown by the diffused reflection spectra measurements and DFT calculations, the structural transformation from [CsEu(H2O)3(SO4)2]·H2O to CsEu(SO4)2 induced a significant band gap reduction. A noticeable difference of the luminescence spectra between cesium europium sulfate and cesium europium sulfate hydrate is detected and explained by the variation of the extent of local symmetry violation at the crystallographic sites occupied by Eu3+ ions, namely, by the increase in inversion asymmetry in [CsEu(H2O)3(SO4)2]·H2O and the increase in mirror asymmetry in CsEu(SO4)2. The chemical shift of the 5D0 energy level in cesium europium sulfate hydrate, with respect to cesium europium sulfate, is associated with the presence of H2O molecules in the vicinity of Eu3+ ion.

Spatial distributions and origin of hydrated sulfate minerals at the mineral bowl in Ophir Chasma, Mars

Numerous occurrences of hydrated minerals (e.g., phyllosilicate, sulfate) have been found on the surface of Mars by remote sensing and in-situ exploration missions, providing strong evidence of the aqueous environment in Martian history. However, the detailed origin of these hydrated minerals is often controversial, reducing their usefulness in constraining the aqueous history of Mars. For instance, in Ophir Chasma, the origins of hydrated sulfates are debatable among hypotheses of precipitating from groundwater, paleolake, or meteoric water. In this study, we performed detailed mineralogy, morphology and stratigraphy analyses of the hydrated phases in the mineral bowl, a depression between the southern wall and mensa of Ophir Chasma, using datasets from Compact Reconnaissance Imaging Spectrometer for Mars (CRISM), High Resolution Imaging Science Experiment (HiRISE) and High Resolution Stereo Camera (HRSC). A large number of monohydrate sulfates (MHS), polyhydrated sulfates (PHS) and some jarosite were identified in this region. Elevation of PHS-rich regions (mean elevation of −1130 ​m) is higher than those of MHS (mean value of −1401 ​m). Spectra of poly- and monohydrated sulfates mixtures were investigated in details in laboratory. Spectral features (i.e., band depth of ~1.9 ​μm, 2.1 ​μm, convexity at 2.1 ​μm and 2.4 ​μm) of sulfates mixtures changed regularly with the abundance of endmember. The linear function between the ratio of BD2100_2 to SINDEX2 and kieserite component was set up to estimate hydrated sulfates abundance. We employ the function onto CRISM data and find a coexistence of poly- and monohydrated sulfates for the formerly recognized PHS endmember, which may indicate a local dehydration/rehydration process for the sulfated minerals. Comprehensive mineralogy, topography, and stratigraphy analyses of hydrated sulfates outcrops suggest a complex formation scenario which could include surface runoff, paleolake, even aeolian erosion.

Development of a Fast Simultaneous Analysis Method for Determination of Middle Rare-Earth Elements in Monazite Samples

Rare earth elements are a set of seventeen metallic elements, which is an essential part of many high-tech devices. Hence, analysis and/or separation of the rare earth elements from their mineral become crucial. A novel analysis method combining ultraviolet-visible spectroscopic and multivariate analysis was developed to determine middle rare earth elements quickly and simultaneously. The data collected from ultraviolet-visible spectroscopic were analyzed by multivariate analysis. The results showed that the developed method has good accuracy and precision with a detection limit of 1.375 (± 0.012), 0.332 (± 0.004), 42.117 (± 0.200), 1.767 (± 0.011), and 0.576 (± 0.002) ppm, respectively for samarium, europium, gadolinium, terbium, and dysprosium. The interference effect of ammonium iron(II) sulfate hexahydrate, manganese(III) sulfate hydrate, calcium carbonate, sodium carbonate, and lead(II) nitrate were examined. The reliability of the proposed method was evaluated using monazite samples. Conclusively, the developed method was successfully applied to determine the middle rare earth elements in monazite samples.

P-Type Chemical Doping-Induced High Bipolar Electrical Conductivities in a Thermoelectric Donor–Acceptor Copolymer

P-Type Chemical Doping-Induced High Bipolar Electrical Conductivities in a Thermoelectric Donor–Acceptor Copolymer

Sodium hydroxide substitution in slag activating mixes: A potential pathway to more sustainable slag-based binders

Alkali-activated slag is commonly used as a cement substitute to reduce the environmental footprint of construction materials. Nonetheless, the use of significant amount of alkaline activators, such as sodium silicate or sodium hydroxide, can be detrimental in terms of global warming potential impact. The aim of this work is to use complementary activators as partial replacement of sodium hydroxide, and therefore reduce the environmental footprint of the activated slag binder. Calcium hydroxide, calcium carbonate, calcium sulfate and magnesium oxide are used as complementary activators in binary or ternary activating mixes. The compressive strength at 28 days are higher (up to 18%) for the calcium carbonate and calcium sulfate-activated samples as compared to the reference activated with sodium hydroxide only. The characterization of the microstructure shows that the proportion of activated slag and the nature of hydrates formed depend on the nature of complementary activators. Calcium aluminum silicate hydrates and hydrotalcite are favored by the presence of calcium carbonate and magnesium oxide, and a sodium calcium aluminum sulfate hydrate is formed in the presence of calcium sulfate. The life cycle impact assessment (LCIA) performed on the different formulations shows that a partial substitution of sodium hydroxide is a potential option to develop more sustainable slag-based binders.

Evaluation of salts in salt pans, Siwa Oasis, Egypt

Siwa Oasis is a tectonically induced depression located in the northern part of the Western Desert. It is intensively characterized by salt mineralization and salt pans. This paper aims to investigate the evaluation of salts from the near-surface underground water in Siwa Oasis to assess the quality of salt for several uses. The study results show that the precipitated minerals identified by XRD are halite, sylvite, gypsum, carnallite, magnesium sulfate hydrate, sodium chlorate, and bischofite. More than 90% of NaCl present in the solution precipitate alone in the first stages. Analysis of heavy metals and trace elements indicated that all the salt samples were found at very low concentrations below the allowable limits. The study indicates that the type of Siwa salt is a very good quality salt, which needs a very simple refining process to meet and exceed the international standards of edible (food) salt.

Spectral and Chemical Characterization of Copiapite and Rozenite from Padinjarathara in Wayanad, Southern India: Implications for Mars Exploration

Copiapite (Fe2+Fe3+4(SO4)6(OH)2 ∙ 20 H2O) and rozenite (Fe2+(SO4) ∙ 4H2O) are secondary hydrous sulfate minerals, mostly formed because of oxygenation and weathering events of primary sulfides on Earth. Acidophiles, mainly archaea and bacteria, and specifically anaerobic methanogens (methane-producing microorganisms) have been detected in regions where alteration of primary sulfide phases to secondary sulfates are predominant. These secondary sulfate minerals are significant in defining past geological environments on Earth and other rocky planets such as Mars. We discuss here the results of chemical and spectral analyses of copiapite and rozenite found in massive sulfide zones associated with banded iron formations (BIFs) in the Wayanad region in Kerala, southern India. The results from different spectroscopic techniques — VNIR reflectance, TIR (emitted radiation), FTIR, Laser Raman, and X-ray diffraction — were recorded and matched with existing literatures and databases. Different matching algorithms like Spectral Feature Fitting (SFF), Spectral Similarity Value (SSV), Modified Spectral Angle Similarity (MSAS), and Pearsonian Correlation Coefficient (PCC) were utilized in order to quantitatively match the reflectance spectra with the reference spectra (USGS and RELAB). The genesis of copiapite and rozenite in the area is through seasonal and temporary development of an acidic environment, with the high elevations of the Wayanad plateau providing the necessary low-humidity condition during the dry season. Copiapite and rozenite were detected as alteration products in different regions on Mars, which can provide insights into environmental conditions that prevailed during the biogeochemical evolution of Mars. The study of copiapite and rozenite formation in a terrestrial environment will therefore enhance our understanding of similar mineral precipitation, genesis, and fluvial processes on Mars. Future missions to Mars could also use the data obtained from the present study to calibrate similar instruments to detect these secondary sulfate minerals.

FEATURES OF THE FORMATION OF THE STRUCTURE OF A CEMENTLESS MATRIX COMPOSITE BASED ON MECHANICALLY ACTIVATED TECHNOGENIC RAW MATERIALS

The creation of composite materials using mechanically activated technogenic raw materials is relevant today as part of a large-scale task of construction and technological utilization of technogenic formations. The change in the crystal structure using mechanochemistry increases the activity of technogenic products: the number of coagulation contacts of dissimilar particles increases, increases the plastic strength of the hardening mixture, formation of hydration products is accelerated. The article is devoted to the study of the mechanism of structural and rheological transformations of a cementless hardening system based on activated steelmaking. Steel melting slags were used as raw materials - energy-saturated large-capacity waste of the West-Siberian Metallurgical Combine (Novokuznetsk). As components - activators - waste from the coal industry of the «Abashevskaya» mine (Novokuznetsk) - burnt rocks with heaps and slimes, obtained by neutralization of spent acid battery electrolytes with lime batteries for industrial vehicles. Based on used mechanically activated technogenic raw materials the binder composite material of the matrix structure is obtained. To assess structural and material changes in the hardening system comprehensive physical and chemical studies were carried out: IR - spectroscopy, thermogravimetric and x-ray phase analysis. Electron microscopy investigated the structure of the stone. It was found that the matrix structure of the composite material is a dispersion medium - matrix of dense fine-grained masses calcium sulfate hydrate; dispersed phase from lamellar crystals of quartz and magnesium oxide, and tubular crystals of calcium orthosilicate; and transitional interfacial layer from structured grains of calcium hydrosulfoaluminate. In the process of forming the structure interdependence of phases from each other was accompanied by a sequential transition of some types of structures to others: coagulation→ crystallization- condensation→ crystallization. The article presents the results of the self-organization of the structure, the interaction of oxide systems in the process of hydration is considered, major mineral neoplasms are established, possessing astringent properties and providing strong bonds between structure-forming components.

Ion-exchange properties of Zn4(OH)6(SO4) 2.5H2O

The aim of the present study is to check the possibilities for ion exchange of a new zinc-hydroxy-sulfate-hydrate phase, Zn4(OH)6SO4·2–2.25H2O. The new zinc hydroxy sulfate hydrate phase was obtained by mixing of 0.5 g of Zn5(OH)8(NO3)2.2H2O and 50 ml of 1M Na2SO4 for 48h at room temperature and pH of the solution between 5–7. Ion-exchange properties were investigated by mixing of 0.2 g Zn4(OH)6(SO4) 2.5H2O with 20 ml water solution of NaCl, CaCl2 or SrCl2 with different concentrations (0.5М, 1М, or 2M) for different time (24h, 48h and 72h) at room temperature. The pH of the solutions varied in the range 6–8. The new phase has exchange properties potentials, like other zinc hydroxy sulfate hydrates composed of octahedral-tetrahedral layers. The results obtained for the kinetics of ion-exchange reactions are additional useful data for the solving of the structure of the new zinc-hydroxy-sulfate-hydrate phase in the future.

Synthesis and the Cathode Properties of Na3Fe3(PO4)4 for Sodium-Ion Battery

Na-ion batteries (NiBs) are very attractive and promising for large scale electric power storage system because of the abundance for sodium source, the high cost-effectiveness and the long lifetime. Among the candidate of cathode active materials for NiBs, practical use of iron phosphate such as NaFePO4, Na2FePO4F, and Na3Fe3(PO4)4 [1] or carbonophosphate such as Na3FePO4CO3 [2] is expected from the viewpoint of cost and safety. In order to make full use of the resource and cost advantages of these materials, the raw materials used in the synthesis and the synthesis method are also important. In this presentation, we report the direct synthesis of Na3Fe3(PO4)4 by the hydrothermal method with mass productivity and the cathode properties. Synthesis was carried out using ferrous sulfate hydrate (FeSO4·nH2O), phosphoric acid, and various sodium phosphate salts as sodium sources with various the raw material composition, hydrothermal treatment temperature, and reaction time. For the purpose of controlling the reaction, synthesis was performed under the condition that an oxidizing agent or a reducing agent was added. The obtained compounds were identified by powder X-ray diffraction measurement and Rietveld analysis. Iron (Ⅱ) sulfate (FeSO4·7H2O), phosphoric acid (H3PO4), sodium dihydrogen phosphate (NaH2PO4·2H2O) and sodium persulfate (Na2S2O8) were used as raw materials, and hydrothermal synthesis was performed at 200 ° C for 16 hours. From the Rietveld analysis, the obtained compound was assigned to the layered structure Na3Fe3(PO4)4. This hydrothermal synthesis Na3Fe3(PO4)4 delivered initial discharge capacity of 160mAh g-1 between -1.2 and 1.3 V with a reference electrode of Ag/AgCl at 2 mA cm-2 in the 17 m NaClO4 aqueous solution (Figure 1). In the presentation, we will be reported the details of cathode properties of Na3Fe3(PO4)4.

Hydrated sulfate minerals (bloedite and polyhalite): formation and paleoenvironmental implications

Salt minerals that are used to reconstruct paleoenvironments should be either primary or samples that provide primary-level information. Using hydrated sulfate minerals that are commonly found in saline lacustrine sediments (i.e., bloedite and polyhalite), the paleoenvironment of the Qaidam Basin, in the northeastern Tibetan Plateau was reconstructed. In this study, we determined the primary and secondary mineral formations based on their S, Mg, H, and O isotopic compositions. While polyhalite is a secondary mineral, bloedite precipitated out from the brine at 0.39 Ma, and ultimately became a secondary mineral at 0.36 Ma. The bloedite and polyhalite Mg isotopes did not record primary signals, but they still provide valuable insights into the paleoenvironments in which they formed. The climate in our study area is very dry; based on the temperature of the brine, this region experienced high temperatures at 0.39 Ma, 0.36 Ma, and 0.12 Ma. We identified one major chemical inconsistency: the bloedite 18O-hydrated water and 18O-SO4 values had basically achieved equilibrium, while the polyhalite and gypsum exhibited no oxygen exchange between their SO4 and hydrated water components. The possible reason for the inconsistency was the differences in mineral crystal structures. We hope that future studies will reconcile this conflicting information.

The role of efflorescent salts associated with sulfide-rich mine wastes in the short-term cycling of arsenic: Insights from XRD, XAS, and µ-XRF studies

The evaporation of As-rich leachates generated by the weathering of sulfide-rich mine wastes accumulated in abandoned tailing dams of the La Concordia mine, triggers the widespread precipitation of saline crusts and efflorescences. Because these salts are highly soluble, they may release high concentrations of arsenic after rainfall events. Thus, the goal of this work is to assess the solid speciation of As in these efflorescences, which may help to understand the short-term cycling of As in the site. The results reveal that As is present only as As(V), while its capacity to be retained in the salts highly depends on their mineralogical composition. Hydrous sulfates, such as gypsum and epsomite show a very low capacity to scavenge As, while copiapite retains the highest concentrations of this element. The spectroscopic evidences suggest that in this mineral, As(V) is included within the lattice, substituting sulfate in the tetrahedral sites. Because copiapite is highly soluble, it may be considered as one of the most important transient reservoirs of As in the site that can release high concentrations of this hazardous pollutant during the occasional rainfall events produced during the wet season.

Structural and spectroscopic study of the kieserite-dwornikite solid-solution series, (Mg,Ni)SO4·H2O, at ambient and low temperatures, with cosmochemical implications for icy moons and Mars

Abstract The investigation of the presence and role of sulfates in our solar system receives growing attention because these compounds play a crucial role in the water budget of planets such as Mars and significantly influence melting equilibria on the icy moons of Saturn and Jupiter, leading to the formation of subsurface oceans and even cryovolcanism. Despite the dominant presence of higher sulfate hydrates such as epsomite, MgSO4·7H2O, and mirabilite, Na2SO4·10H2O, on these moons' surfaces, it is not excluded that lower-hydrated sulfates, such as kieserite, MgSO4·H2O, are also present, forming from higher hydrates under pressures relevant to the mantle of the icy moons. Given the composition of the soluble fraction in C1 and C2 chondritic meteorites, which are high in Ni content and also considered to represent the composition of the rocky cores of the Jovian icy moons, the actual compositions of potentially present monohydrate sulfates likely lie at intermediate values along the solid-solution series between kieserite and transition-metal kieserite-group end-members, incorporating Ni in particular. Moderate Ni contents are also probable in kieserite on Mars due to the planet's long-term accumulation of meteoritic nickel, although likely to a much lesser extent than Fe. Structural and spectroscopic differences between the pure Mg- and Ni-end-members have been previously documented in the literature, but no detailed crystal chemical and spectroscopic investigation along the Mg-Ni solid solution has been done yet. The present work proves the existence of a continuous (Mg,Ni)SO4·H2O solid-solution series for the first time. It provides a detailed insight into the changes in lattice parameters, structural details, and positions of prominent bands in infrared (transmission, attenuated total reflectance, diffuse reflectance) and Raman spectra in synthetic samples as the Ni/Mg ratio progresses, at both ambient as well as low temperatures relevant for the icy moons and Mars. UV-Vis-NIR crystal field spectra of the Ni end-member also help to elucidate the influence of Ni2+-related bands on the overtone- and combination modes. The (Mg,Ni)SO4·H2O solid-solution series shows Vegard-type behavior, i.e., lattice parameters as well as spectral band positions, change along linear trends with increasing Ni content. Infrared spectra reveal significant changes in the wavenumber positions of prominent bands, depending on the Ni/Mg ratio. We show that the temperature during measurement also has an influence on band position, mainly in the case of H2O-related bands. The changes observed for several absorption features in the IR spectra enable rough estimation of the Ni/Mg ratio in the monohydrate sulfate, which is applicable to present and future remote sensing data, as well as in situ measurements on Mars or the icy moons. The spectral features most diagnostic of composition are the vibrational stretching modes of the H2O molecule and a band unique to kieserite-group compounds at around 900 cm–1 in the IR spectra, as well as the pronounced ν3 and ν1 sulfate stretching modes visible in Raman spectra.

Characterization of Fe-based sediments received from chemical pre-treatment of hydrometallurgical waste leachate from the recycling of alkaline batteries

The waste leachate from the hydrometallurgical recycling of spent batteries contains a significant amount of undesirable iron that needs to be precipitated before the recovery of target metals. The produced Fe-sediments are usually disposed of or stored at the treatment site as waste and are often poorly managed. This work estimates the environmental stability and application potential of Fe-sediments produced from highly acidic hydrometallurgical leachate during the recycling of spent alkaline batteries. After pH neutralization of the leachate by Na2CO3, a primary Fe-sediment (PFS), mainly composed of highly unstable metal (i.e., Fe, Zn, and Mn) sulfates, was obtained. The subsequent rinsing of this unstable PFS sediment led to the production of a secondary Fe-sediment (SFS), which was composed of an amorphous-phased ferric iron sulfate hydrate – Fe16O16(SO4)3(OH)10·10H2O. The results of single extraction using chemical reagents and biological dissolution by iron-transforming bacteria confirmed that despite most of the ions in PFS were dissolvable, the processed SFS was environmentally safe. The sorption efficiency of SFS towards Pb(II) and As(V) (up to ~ 99% and 94%, respectively, with an initial concentration of 100 mg/L) was found to be promising, suggesting the high potential for economical reuse of SFS.

Kinetics of hydrogenation of acrylonitrile butadiene rubber: a latex-based in situ and low-temperature approach

The kinetics of hydrogenation of acrylonitrile butadiene rubber (NBR) latex by the action of diimide generated by hydrazine hydrate and hydrogen peroxide in the presence of copper sulfate at low temperature was studied by calculating the initial reaction rate constants. Altering reaction parameters of different reactant dosages such as carbon-carbon double bonds, hydrazine hydrate, hydrogen peroxide, and copper sulfate can be designed to calculate the initial reaction rate constant in a hydrazine hydrate/hydrogen peroxide/copper sulfate reaction system. The method of initial reaction rate constants gives rate constant and reaction order in the hydrogenation reaction of NBR latex calculated from the hydrogenation kinetic data. Based on these kinetic values, the kinetic equation of hydrogenation of NBR latex in this catalytic system at the temperature ranged from 5 to 65 °C and the hydrogenated reaction activation energy were studied in this paper. Graphical abstract

The active ingredients in the anti‐obesity drug bofutsushosan in high‐fat‐diet‐fed obese mice

ABSTRACTAimCombined effects on the body weights and white adipose tissues in high‐fat‐diet‐fed obese mice due to bofutsushosan (BTS) were investigated.MethodsMale ICR mice (four weeks old) were fed a 60% kcal fat diet for five weeks and fed the same diet with administration of aqueous extracts (2.0 g/kg/day) of BTS, component‐removed BTS, and a mixture of the ingredients and the component‐removed BTS for 28 days.ResultsThe BTS extract reduced the body weight from 2 to 28 days after administration while also reducing the weight of the subcutaneous and visceral white adipose tissues after administration for 28 days. Extracts of BTS with Glycyrrhizae radix (Glycyrrhiza root; abbreviated as glycyrrhiza) removed, Rhei rhizoma (rhubarb rhizome; rhubarb) removed, Gardeniae fructus (Gardenia fruit; gardenia) removed, Ephedrae herba (Ephedra herb; ephedra) removed, or Sal mirabilis (sodium sulfate hydrate; mirabilite) removed reduced the anti‐obesity and fat‐loss activity compared to that of the BTS extract after administration for 28 days. Glycyrrhizic acid (0.89% [w/w]) and 0.046%(w/w) sennoside AB calcium salt ameliorated the anti‐obesity activity of BTS with glycyrrhiza removed and rhubarb removed eight days after administration, respectively. Geniposide (0.78% [w/w]) and 0.16% (w/w) ephedrine hydrochloride ameliorated the anti‐obesity and fat‐loss activity of BTS with gardenia removed and with ephedra removed respectively after administration for 28 days.ConclusionGlycyrrhiza, rhubarb, gardenia, ephedra and mirabilite were the active components responsible for the effect of BTS. Glycyrrhizic acid and sennoside AB induced the early phase while geniposide and ephedrine hydrochloride induced the later phase of the anti‐obesity activity of BTS.