Hydraulic Loading Research Articles

Comparative analysis of experimental and simulation results of composite circular tube

Abstract In this work, the internal pressure of the composite pipe is analysed and studied when transporting liquid or gas. The quasi-static hydraulic test is designed to simulate the internal pressure of the composite pipe. By using the ABAQUS finite element method, a numerical model of the composite pipe under hydraulic load is established. The strain curves and final failure modes of the test and simulation are compared to verify the feasibility of the finite element method model. Finally, the damage mechanism of the composite tube is analysed according to the numerical model, and it is found that the carbon fibre composite material has an important effect on the bearing capacity of the composite tube.

Connecting past, present, and future trends of hydraulic and phosphorus loading in the Bay of Quinte tributaries, Ontario, Canada

Study regionThe Bay of Quinte watershed, located on the northeastern shore of Lake Ontario, Canada. Special focus is placed on the Napanee River and Wilton Creek catchments, where the presence of a subterranean network of conduits that facilitate groundwater-surface water interactions is conducive to an increase in the delivery of nutrients during storm events and can exacerbate the risk of eutrophication. Study focusDevelopment of a rigorous modelling framework that can advance our understanding of past and present trends of streamflow and tributary phosphorus (P) concentration and loads. We also analyze future streamflow rates and P export trends in order to guide the long-term watershed management in the area. Our analysis is carried out through a comprehensive combination of data-driven and process-based models. Novel hydrological insights for the regionRetrospective analysis provides evidence of a recent increase in the impact of nonpoint-source P pollution. General Circulation Models suggest a future increase in both temperature minima and maxima relative to present conditions (2002–2018). Precipitation projections are indicative of increased frequency of occurrence of high extreme precipitation events during the summer and mid-fall, when the Bay of Quinte is more susceptible to undesirable ecological shifts. Our study predicts a seasonality shift in the streamflow, with the spring freshet occurring earlier in the year accompanied by higher flow rates in the local creeks for the winter and early spring. We also examined the relationship between precipitation and streamflow across varying levels of flow regulation. Our analysis indicates that our predictive capacity declines with increased flow regulation as well as when streamflow rates are predicted by contemporaneous precipitation values.

The Regulatory Effect of Hydroelectric Reservoir Hydraulic Load on the Assimilation Efficiency of Nutrients

The Regulatory Effect of Hydroelectric Reservoir Hydraulic Load on the Assimilation Efficiency of Nutrients

Use of recycled construction and demolition waste as substrate in constructed wetlands for the wastewater treatment of cheese production

Recycled building debris has recently emerged as a suitable wetland infill substrate due to its low density, exceptional water absorption capabilities, and high porosity. This study investigated, for the first time, the use of construction demolition wastes (CDW), and rock processing residues (RPR) as substrate materials in vertical-horizontal flow hybrid constructed wetlands for the treatment of cheese production wastewater. Results showed that the use of both CDW as well as RPR, as substrate material, provided an equal or even better quality of treated wastewater compared to the conventional use of gravel as a substrate. High removal efficiencies were recorded for turbidity (CDW: 91–92%, RPR: 97%), solids (CDW: 85–88%, RPR: 96–97%), organic matter (CDW: 79–84%, RPR: 96–98%), and total phosphorus (CDW: 72–76%, RPR: 87%) for both examined recycled materials. During the experiment, different loadings rates (HLR) were tested: 25 mm d−1 and 37.5 mm d−1. Radiological measurements indicate that, their use did not cause toxic effects on the environment, as the amounts of radioactivity found in the effluent of the systems are not significant. Increasing the hydraulic loading rate appeared to have no negative effect on pollutant removal, as the systems and plants were fully acclimated and mature. This approach offers several advantages, including the use of readily available and abundant waste material, potential cost savings, and the environmental benefits of recycling CDW and RPR instead of disposing of them in landfills.

Evolution mechanism of hydraulic fracture in concrete under dynamic loading

The influence of hydraulic loading within cracks on the evolution mechanism of concrete under dynamic loading was investigated in this paper. Several strain gauges were employed to stick along the crack tip during the experiments. The moving crack tip was captured using these gauges during fracture. In particular, during the stable cracking stage, consistent propagating crack-tip speeds were observed under varying water pressures. Initially, the measured speed measured 2.0 m/s, which later increased to 20.0 m/s. Based on hydraulic experiments, a relationship between the crack tip and the water front was established, allowing the derivation of pressure distribution within crack from experimental data collected under dynamic loading conditions. Furthermore, the fracture parameters, including initial toughness, critical toughness, and cohesive toughness, were calculated for concrete subjected to split loading. The cohesive toughness experienced a 13.9% reduction with the increasing hydraulic pressure to 0.4 MPa, highlighting the deterioration of cohesive fracture toughness due to water infiltration within the concrete crack. This study provides insights to improve the design of civil and hydraulic engineering structures, such as gravity dams.

Finite element numerical analysis of structural vibration of a certain pump station

Abstract In the process of pump station operation, the vibration of factory structure caused by hydraulic or mechanical factors will seriously threaten the ordinary operation of pump station; reduce the efficiency of units; shorten the service lifespan of equipment, and even lead to failure of units. In this paper, ANSYS software and modal analysis method are applied to simulate the vibration effect on pump station under natural vibration, unit vibration excitation and hydraulic excitation. The intrinsic vibration features of pump station structure under diverse boundary conditions, different working conditions and distinct external excitation sources are studied. According to the results of modal and harmonic response analysis, it can be concluded that: 1. A cross relationship has been found existing between pump station structure and unit excitation of speed frequency. 2. In addition to the upper part of the pump station fragile structure, the vibration of the pier is more noteworthy. 3. The vibration amplitude of the whole pump station along vertical direction is larger than that in other directions while the deformation following the unit axis and flow direction presents a strong tendency. 4. In general, the influence of hydraulic load on the structural force of pump station is relatively small.

The impact of benzoic acid and lactic acid on the treatment efficiency and microbial community in the sulfur autotrophic denitrification process.

Nitrate poses a potential threat to aquatic ecosystems. This study focuses on the sulfur autotrophic denitrification mechanism in the process of water culture wastewater treatment, which has been successfully applied to the degradation of nitrogen in water culture farm effluents. However, the coexistence of organic acids in the treatment process is a common environmental challenge, significantly affecting the activity of denitrifying bacteria. This paper aims to explore the effects of adding benzoic acid and lactic acid on denitrification performance, organic acid removal rate, and microbial population abundance in sulfur autotrophic denitrification systems under optimal operating conditions, sulfur deficiency, and high hydraulic load. In experiments with 50 mg·L-1 of benzoic acid or lactic acid alone, the results show that benzoic acid and lactic acid have a stimulating effect on denitrification activity, with the stimulating effect significantly greater than the inhibitory effect. Under optimal operating conditions, the average denitrification rate of the system remained above 99%; under S/N = 1.5 conditions, the average denitrification rate increased from 88.34% to 91.93% and 85.91%; under HRT = 6h conditions, the average denitrification rate increased from 75.25% to 97.79% and 96.58%. In addition, the addition of organic acids led to a decrease in microbial population abundance. At the phylum level, Proteobacteria has always been the dominant bacterial genus, and its relative abundance significantly increased after the addition of benzoic acid, from 40.2% to 61.5% and 62.4%. At the genus level, Thiobacillus, Sulfurimonas, Chryseobacterium, and Thermomonas maintained high population abundances under different conditions. PRACTITIONER POINTS: Employing autotrophic denitrification process for treating high-nitrate wastewater. Utilizing organic acids as external carbon sources. Denitrifying bacteria demonstrate high utilization efficiency towards organic acids. Organic acids promote denitrification more than they inhibit it. The promotion is manifested in the enhancement of activity and microbial abundance.

Evaluation of Countermeasures for Hydraulic Loading on Bridges

Evaluation of Countermeasures for Hydraulic Loading on Bridges

Subsurface wastewater infiltration systems for nitrogen pollution control.

Subsurface wastewater infiltration systems (SWISs) are suggested to be a cost-effective and environmentally friendly method for sewage treatment. However, a comprehensive summary of the relevant mechanisms and optimization methods for nitrogen (N) removal in SWIS is currently lacking. In this review, we first summarize the N transformation mechanisms in SWIS. The impact of operational parameters on the N removal efficiency is then delineated. To enhance pollutant removal and minimize resource wastage, it is advisable to maintain a wet-dry ratio of 1:1 and a hydraulic loading rate of 8-10cm/day. The organic load should be determined based on influent characteristics to optimize the balance between sewage treatment and nitrous oxide (N2O) emission. Finally, various strategies and modifications have been suggested to enhance pollutant removal efficiency and reduce N2O emissions in SWIS, such as artificial aeration, supply electron donors, and well-designed structures. Overall, greater emphasis should be placed on the design and management of SWIS to optimize their co-benefits while effectively controlling N pollution. PRACTITIONER POINTS: SWISs are often considered black boxes with their efficiency depending on hydraulic characteristics, biological characteristics, and substrate properties. Biological nitrification coupled with denitrification is considered to be the major N removal process. Increasing the reduction of N2O to the inert N2 form is a potential mechanism to mitigate global warming. Strategies such as artificial aeration, supply electron donors, and well-designed structures are suggested to improve N removal performance.

Effective nutrient removal from aquaculture wastewater utilizing an indoor nutrient film technique hydroponic system

AbstractAquaculture wastewater treatment must remove nutrients to prevent eutrophication of receiving waters and to allow for possible re‐use of the treated water. This study aims to evaluate the shoot and root growth of crops produced in Nutrient Film Technique hydroponic systems and treat aquaculture wastewater using phytoremediation. The average physico‐chemical parameters of the aquaculture wastewater during the study period were pH 6–6.4, temperature 25°C–27°C, EC 0.7–0.8 mS/cm, and total dissolved solids (420–560 ppm). The operating conditions of hydroponic treatment units were hydraulic loading rate of 857.28 m/day, hydraulic retention time of 0.3 h, organic loading rate of 12567.8 Ibs‐BOD5/ft^2/day (BOD5 is 5 – day Biochemical Oxygen Demand) and flow rate of 54 L/h. The study found that the average elimination efficiency of nitrate‐nitrogen in aquaculture wastewater treatment varied from 78.28% by Money plants (Epiprennum aureum), 71% by Crotons (Codiaeum varigatum), 70.25% by Arrowhead plants (Syngonium podophyllum), 67.25% by Purple Heart (Tradescantia pallida), 68.62% by for Spinach (Spinacea oleracia), and 42.85% by Brinjal plants (Solanum melongena). The average removal effectiveness of BOD5 varied from 71.07% by Money plants (Epiprennum aureum), 68.62% by Crotons (Codiaeum varigatum), 78% by Arrowhead plants (Syngonium podophyllum), 72% by Purple Heart (Tradescantia pallida), 68% by Spinach (Spinacea oleracia), and 70% by Brinjal plants (Solanum melongena). Thus, environmentally friendly and economically advantageous method for reducing and removing nitrate‐nitrogen and BOD5 from aquaculture effluent is hydroponic phytoremediation. The promising potential of using indoor NFT hydroponic systems for nutrient removal particularly nitrate‐nitrogen, from aquaculture wastewater. Each plant species is assessed for its ability to uptake and reduce nitrate‐nitrogen levels, growth patterns, and overall suitability for wastewater treatment. The study emphasizes the eco‐friendly and sustainable wastewater management nature of the proposed method.

Mechanical behavior evolution and failure characteristics of saturated and dry rocks under different water pressure environments

A complex and changeable water environment is a key factor for safe rock engineering. Variations in water distribution and pressure pose serious challenges in evaluating rock properties and failure modes. To investigate the effect of real water‒rock interactions on rock mechanical behavior, the self-developed hydraulic loading test equipment was designed. A series of mechanical experiments (unjacketed) were carried out on three representative types of rocks under different water pressure environments, and the jacketed test was also performed for the saturated rocks. The experimental results showed that with increasing water confining pressure, the stress‒strain curve of the saturated rocks increased, while that of the dry rocks first decreased and then increased, and that of the sandstone became more obvious. Furthermore, when the water confining pressure increased, the peak stress and elastic modulus of the saturated rocks increased linearly, and those of the dry rocks first decreased and then increased more sharply. Interestingly, the water confining pressure weakened the local tensile failure and aggravated the shear failure. The relationship between the water confining pressure and strength also indicated that the change of saturated rocks more slowly when in contact with the water confining pressure. From the above results, the pore water pressure correction coefficients (μ) of sandstone, marble and granite were 0.98, 0.96 and 0.93, respectively, in the water pressure environment and rock connection. The failure mechanism of saturated rocks is similar to that of rocks without confining pressure due to the balance of the water confining pressure and pore water pressure, and pore water pressure mainly acts as piestic water. For dry rocks, the penetration of pore water firstly weakens the mechanical properties of rocks when pore water pressure is smaller. A greater confining pressure enhances the role of traditional confining pressure for granite and dry rocks.

Treatment efficiency and recovery in sand filters for on-site wastewater treatment: Column studies and reactive modelling

This study examined the adsorption capacity and treatment efficiency of sand filters in on-site treatment systems for cold climate regions. The effects of different operating conditions, porosity and kinetics parameters were investigated in column experiments and COMSOL Multiphysics® modelling, to comprehensively reveal the mechanisms and optimize treatment efficiency of nitrogen (N) and phosphorus (P) removal in a field tidal flow constructed wetland (TFCW), treating effluent from a package treatment plant with P filter material. The results from column experiments with sand showed that Total-P adsorption rate was dependent on feed water quality (Septic tank >0.77 ± 0.06 g kg−1; Biotreatment >0.41 ± 0.07 g kg−1; Reactive material Polonite® <0.18 ± 0.07 g kg−1). In the field TFCW trial, Total-P adsorption in the top layer (>1.42 ± 0.55 g kg−1) and middle layer (>1.06 ± 0.51 g kg−1) was twice that in laboratory columns, due to strong interaction with the air-water interface and use of fluctuated domestic wastewater solutions. The breakthrough curve (BTCs) of the coarse sand matched the physical behaviour of tracer electrical conductivity (EC) in effluent from the sand column experiments. The modelling results demonstrated that high filter porosity and low hydraulic load were significant factors for optimal removal of NH4–N, Total-N, PO4–P, Total- P in the top layer (>99.95 ± 0.03 %, 44.37 ± 28.75%, 70.89 ± 28.30%, 76.18 ± 20.3%), middle layer (>98.94 ± 1.77%, 18.23 ± 23.04%, 76.62 ± 28.73%, 65.40 ± 31.85%) and deep layer (>99.99 ± 0.02%, 65.50 ± 20.64%, 75.53 ± 23.16%, 41.54 ± 28.81%) in the TFCW system, respectively. The results show that on-site wastewater treatment in cold climate TFCW can be applied as a technology to polish effluent from a three-step pretreatment system. However, hydraulic optimization is an important factor for the design of the TFCW to receive a successful long-term operating system.

Enhanced Simultaneous Nitrogen and Phosphorus Removal in a Continuous-Flow Granular Sludge System under Gradient-Controlled Hydraulic Loading

The feasibility of the aerobic granulation of activated sludge was investigated in a continuous-flow anaerobic–anoxic–oxic system under gradient-controlled hydraulic loading on the surface of a cyclone separator. Concentrated domestic sewage was used. After 80 days of operation, 80% of activated sludge in the system was in the form of granular sludge with an average particle size of 373 μm. High removal efficiency was achieved for chemical oxygen demand (94.40%), NH4+-N (99.93%), total nitrogen (89.44%), and total phosphorus (96.92%). A batch study revealed that Pseudomonas (1.34%) and Dechloromonas (1.05%) as the main denitrifying phosphorus-accumulating organisms could efficiently remove phosphorus using nitrate as an electron acceptor, which improved the utilization efficiency of carbon sources and achieved simultaneous denitrification and phosphorus removal. Overall, the study demonstrates the feasibility of enhanced denitrification and phosphorus removal in a continuous-flow granular sludge system. The sludge system enables simultaneous nitrogen and phosphorus removal under low carbon-to-nitrogen ratios.

Mechanism of vertical displacement beneath shallow compression zone in coastal area

Previous studies showed that there is a discrepancy between total subsidence (measured on the ground surface) and shallow compression (measured within several hundred meters beneath the ground surface) in Taiwan. This difference is referred to as deep displacement in this study. The variations of deep displacement are opposite to those of ground surface displacement and groundwater level within the depth of several hundred meters. The mechanism is unknown and requires further investigation. This study adopts two kinds of geodetic observation data and separates land subsidence into shallow compression and deep displacement to investigate the mechanism of deep displacement. A tectonically active coastal area in Taiwan is selected as the study area. The assessment results show that the associated variations are likely due to cyclic hydraulic loading and unloading. The variations of deep displacement are opposite to those of ground surface displacement. This study proposes that these variations are due to hydraulic expansion and contraction. The mechanism is demonstrated using a hydromechanical model. The results of a cross-correlation analysis show that hydraulic expansion and contraction occur at certain depths. The study results provide important information on the mechanism of deep displacement that can be used in tectonophysical and land subsidence investigations.Graphical

An in-depth analysis of the hydrodynamic behaviour of a high-rate lamellar DAF tank by means of CFD simulations

This research is based on computational fluid dynamics simulations of water and microbubble flow within the tank of a lamellar DAF (L-DAF) clarification system operating under high-rate DAF conditions (12–30 m/h). Firstly, performance of the DAF tank with lamellae was evaluated under two operating conditions in which the flow was either short-circuited or stratified in the absence of lamellae. In addition, the improvement in bubble removal efficiency achieved by the incorporation of lamellae in each scenario was assessed. Secondly, an in-depth analysis was conducted of the flow that develops in the separation zone as a result of placing the lamella pack in that part of the tank. The significant density difference that the lamellae cause to exist between the bubble blanket and clarified water below is responsible for the complex three-dimensional flow observed between the two regions. Analysis of this flow showed a previously undescribed mechanism in which the density gradient plays a crucial role in preventing bubbles from passing through the lamellae and ultimately escaping with the effluent. Finally, the effect of hydraulic loading on the bubble removal efficiency of the L-DAF tank under consideration was researched, and it was found that an L-DAF with a height/length ratio of 0.72 is able to operate at hydraulic loading close to 30 m/h, evidencing good debubbling performance.

Varying removal of emerging organic contaminants in drinking water treatment residue-based biofilter systems: Influence of hydraulic loading rates on microbiology

Drinking water treatment residue (DWTR)-based biofilter is an environment-friendly and cost-effective technology for eliminating nutrients and emerging organic contaminants (EOCs) from natural water. This study explored the removal efficiencies of five trace-level EOCs and the associated microbial response of biofilm in two identical DWTR-based biofilters under varying hydraulic loading rate (HLR) conditions over six months of operation. The results showed that the most recalcitrant EOC (carbamazepine) was mainly removed by DWTR adsorption (7.8–11.0 ng g−1), while the response of the biofilm community to HLR significantly affected the degradation of 17α-ethinylestradiol, sulfamethoxazole, roxithromycin, and sulfathiazole (P < 0.001). A higher HLR significantly stimulated the production of extracellular polymeric substance and increased the stochasticity and diversity of community assembly, improving denitrification and the removal efficiency of DWTR-based biofilm for biodegradable roxithromycin (80 %) and sulfamethoxazole (76 %). In contrast, lower HLR led to carbon limitation and exerted substrate selection pressures, resulting in more deterministic and stable community assembly, with keystone species such as Bacillus enriched in EOC degradation-related functional genes. Moreover, co-occurrence network analysis revealed a simpler but more intensive interaction network among EOC degraders under the lower HLR condition. This interaction network facilitated the co-metabolism of influent organic carbon and the removal of more recalcitrant contaminants, 17α-ethinylestradiol (48 %) and sulfathiazole (37 %). This study offered a novel insight into biofilter management from a hybrid perspective of environmental microbiology and engineering science, highlighting the dynamic adaptation of microbes to specific EOC degradation under varying HLR conditions.

Heavy metals removal in a graphene engineered concrete-based filter column

In this study, crushed aggregate surfaces were coated with reduced graphene oxide (RGO) using a chitosan-derived solution and included in porous concrete-based filter column samples to improve heavy metal removal. The RGO coating strengthened the aggregate and cement interfaces, thus improving the compressive strength of these samples by up to 18 %. The removal of lead and copper in samples containing RGO coated aggregate (GCA) operated with a minimum hydraulic load was found to be 97 % and 92 %. Increasing the hydraulic load reduced this heavy metal removal, but the presence of GCA increased the active sites for heavy metal ions to immobilize, leading to improved copper removal under such operating conditions. Calcium ions from the cement hydrates were found to leach from the concrete matrices during such a wastewater passage. This leaching of calcium ions was determined to be relatively lesser in RGO decorated concrete samples, pointing out the positive effects of GCA on the resistance of the concrete matrices to aggressive chemicals. Clay particles containing highly turbid water were also passed through these concrete samples to examine the effects on the infiltration rate. Clay particles were found to clog pores, marginally reducing the infiltration rate. Concrete-based water filters are easy to operate and have low maintenance requirements, and industries responsible for heavy metal pollution in aquatic environments can widely adopt them instead of complex treatment methods.

Optimal control strategies for stormwater detention ponds

Stormwater detention ponds are essential stormwater management solutions that regulate the urban catchment discharge towards streams. Their purposes are to reduce the hydraulic load to avoid stream erosion, as well as to minimize the degradation of the natural waterbody by direct discharge of pollutants. Currently, static controllers are widely implemented for detention pond outflow regulation in engineering practice, i.e., the outflow discharge is capped at a fixed value. Such a passive discharge setting fails to exploit the full potential of the overall water system, hence further improvements are needed. We apply formal methods to synthesize (i.e., derive automatically) optimal active controllers. We model the stormwater detention pond, including the urban catchment area and the rain forecasts with its uncertainty, as hybrid Markov decision processes. Subsequently, we use the tool UppaalStratego to synthesize using Q-learning a control strategy maximizing the retention time for pollutant sedimentation (optimality) while also minimizing the duration of emergency overflow in the detention pond (safety). These strategies are synthesized for both an off-line and on-line settings. Simulation results for an existing pond show that UppaalStratego can learn optimal strategies that significantly reduce emergency overflows. For off-line controllers, a scenario with low rain periods shows a 26% improvement of pollutant sedimentation with respect to static control, and a scenario with high rain periods shows a reduction of overflow probability of 10%–19% for static control to lower than 5%, while pollutant sedimentation has only declined by 7% compared to static-control. For on-line controllers, one scenario with heavy rain shows a 95% overflow duration reduction and a 29% pollutant sedimentation improvement compared to static control.

Decay Of Bow Thruster Induced Near-Bed Flow Velocities At A Vertical Quay Wall: A Field Measurement

During berthing operations vessels use bow thruster(s) to improve their manoeuvrability, making them less dependent on the assistance of tugboats. While manoeuvring, the transversal bow thruster jet can reflect on the quay wall and partially be directed towards the bed. At the intersection between the quay wall and the bed, the jet reflects again leading to a highly turbulent and complex flow field (Figure 1). When the bed is left unprotected scour may occur, which can eventually lead to instability of the quay wall (Roubos et al., 2014). Over the years, the shipping industry has been developing continuously, characterized primarily by the upscaling in size of inland- and sea-going vessels (OECD, 2015; Weenen et al., 2020; Looye, 2021). As a result, vessels have larger draughts, more power and larger thruster diameters leading to higher hydraulic loads on quay walls and bed protections of berthing facilities (Roubos &amp; Verhagen, 2007). To complicate the matter even more, the jet from a transversal bow thruster is confined by the hull of the vessel, the quay wall and the bed. Leading to a complex flow field of the reflected jet and an unknown decay in near-bed flow velocities. Resulting in uncertainties in the design of bed protections, especially in the required width.

Large Scale Physical Model Study On Clay Erosion With Gras Cover On Primary Coastal Defence Structures

Sea dikes in the Netherlands consist of sandy or clay core with a clay layer with grass. The lower outer slope is often covered with a hard revetment, such as asphalt or a placed block revetment, to protect the dike material against wave impact. Since the strength of the clay layer with a grass subject to severe wave impact is unknown, the hard revetment needs to be constructed on a large part of the outer slope to ensure that the flood defence meets the safety requirements. Therefore, a research programme was started to determine the strength of the clay layer with grass on the upper slope of a dike. As a first step, large scale physical model tests have been performed. In the second step the CFD model OpenFOAM has been used to extend the physical model results by computing the peak pressure of the hydraulic load on the clay for the tested geometries and additional geometries with varying parameters that may influence the erosion rate. With all results, it was possible to derive formulas for failure probability calculations in the final step. The knowledge development on the erosion of a clay layer with grass on the outer slope by wave attack resulted into formulas that are currently used in the safety assessment of dikes contributing towards safer deltas and resilient designs of dikes.