Horizontal And Vertical Research Articles

Determining patterns of the vertical load on a covered wagon roof with a frame in the form of a triangular arch

The object of this paper is the processes of perception and redistribution of loads in the roof of a railroad covered wagon with a frame in the form of a triangular arch. To reduce the tare of the covered wagon, it is proposed to improve the structure of its roof. A feature of this improvement is that the roof frame is made in the form of a triangular arch with a reinforcing belt. This contributes to the reduction of the total mass of the roof compared to a typical structure. The selection of execution profiles of the beams forming the arch is carried out according to the maximum values of the moments that act in their cross-section. Taking into account the chosen profile of the arches, the calculation of the strength of the roof when it receives vertical loads was carried out. It was established that the strength of the roof under the considered load schemes is within the permissible stress values. Since the improvement of the roof structure contributes to the reduction of its weight by 1.8 % compared to the prototype, the movement of the covered wagon was evaluated under conditions of moving while empty. To this end, a mathematical modeling of the load of the covered wagon in the vertical plane during its movement along the joint unevenness was carried out. On the basis of the performed calculation, it was established that the movement of the wagon is assessed as "good". Special feature of the results is that the reduction of the tare of the supporting structure of the wagon was achieved by improving its roof, as the least loaded unit. The field of practical application of the results is railroad transport, including other areas of mechanical engineering. The conditions for the practical use of the results are a symmetrical roof load scheme in operation. The results of this research could contribute to advancements related to the design of modern structures of freight wagons with improved technical and economic indicators

Thermal effect of the anisotropic metal foam on the melting performance of phase change material: A pore-scale study

Recently, metal foams have been attractive in reinforcing the heat storage process of phase change materials (PCMs) beneficial from their high thermal conductivity, interconnected structure, and large specific surface. Nevertheless, the melting of PCM is not uniform caused by convective heat transfer, so it cannot be sufficiently accelerated by a traditional isotropic metal foam. In this study, we numerically investigated the melting performance of PCM in isotropic and anisotropic metal foams. Results illustrated that the X-anisotropic structure can more efficiently enhance the melting performance as compared to the isotropic original metal foam, but the Z-anisotropic structure suppresses it. Moreover, the X-anisotropy-0.5 shows the fastest melting, its complete melting time is significantly reduced by 7.99 % compared with the original model, and its heat storage power is 8.68 % higher than the original one. Instead, the Z-anisotropic models prolong the complete melting time by 11.10 % ˗ 28.55 %. It is owing that the anisotropic structure would promote the heat transfer along one direction but suppress its vertical direction. This article provides a feasible routine to accelerate the melting of metal foam-based PCMs, thus improving the heat storage power of the latent heat thermal energy storage system.

Enhancement of rider comfort by magnetorheological elastomer based damping treatment at strategic locations of an electric two wheeler

The vibrations generated in the two-wheeled vehicles like motorcycles due to road irregularities such as cracks, potholes, and bumps on the road cause discomfort for the rider as well as the pillion. These vibrations are reported to cause lower back pains, musculoskeletal effects, fatigue, and long-term health issues. Particularly, electric two-wheelers are more susceptible to these vibrations caused by the road and need attention. This paper presents an innovative technique for the reduction of vibrations at prominent locations in the electric two-wheeler to improve the rider’s comfort. All measured accelerations are about vertical direction (along z-axis as per ISO 2631-1 standard). Passive and Semi-active damping treatments namely, Room temperature vulcanizing Silicone rubber and Magnetorheological elastomer (MRE) were applied on the test vehicle at strategic locations of vibration. Both were compared for their effectiveness in reducing the vibrations. Results showed that MRE based damping technique proved better vibration isolation at the strategic locations. The weighted root mean square acceleration as well as vibration dose values were found to decrease with the help of damping treatments thus improving the rider’s overall comfort level.

The influence of water turbulence on surface deformations and the gas transfer rate across an air–water interface

We present experimental results of a study on oxygen transfer rates in a water channel facility with varying turbulence inflow conditions set by an active grid. We compare the change in gas transfer rate with different turbulence characteristics of the flow set by four different water channel and grid configurations. It was found that the change in gas transfer rate correlates best with the turbulence intensity in the vertical direction. The most turbulent cases increased the gas transfer rate by 30% compared to the low turbulence reference case. Between the two most turbulent cases studied here, the streamwise turbulence and largest length scales in the flow change, while the gas transfer rate is relatively unchanged. In contrast, for the two less turbulent cases where the magnitude of the fluctuations normal to the free surface are also smaller, the gas transfer rate is significantly reduced. Since the air–water interface plays an important role in the gas transfer process, special attention is given to the free-surface deformations. Despite taking measures to minimise it, the active grid also leaves a direct imprint on the free surface, and the majority of the waves on the surface originate from the grid itself. Surface deformations were, however, ruled out as a main driver for the increase in gas transfer because the increase in surface area is < 0.25%, which is two orders of magnitude smaller than the measured change in the gas transfer rate.

Facial growth dynamics dictate optimal facemask fitting during the first year of life.

The aim of this study is to prevent mask leak during ventilation in infant emergencies, appropriate facemask fitting is essential. Therefore, we investigated facial profiles during the first year of life and their correlation with the correct sizing of masks. This is a post hoc subgroup analysis of 32 healthy term infants, based on a prospective observational study performed from September 2018 to December 2019 in Tuebingen, Germany. In 3-monthly intervals, facial aspects were measured based on anatomical landmarks in three-dimensional frontal photographs to describe their changes across the first year of life. All infants were awake and breathing spontaneously; none required any anaesthesia. In 130 3D images, mean distance between nasion and gnathion was 54 mm (3.3) measured at birth and 70 mm (3.5) at age 12 months. Gompertz models showed relevant growth-related changes in the facial profile in vertical but not horizontal direction. Vertical growth occurred mainly in the first 6 months. Boys and girls differed by an average of about 2 mm (boys >girls). Based on our findings, it should now be verified whether the 50 mm facemasks are suitable for infants from birth to 2 months of age, respectively, the 60 mm version for infants aged three to 12 months.

Mechanical response, damage constitutive and failure localization characteristics of structural backfills composed of matrixes with different mechanical properties

To investigate the mechanical properties, damage progressivity characteristics, and failure modes of layered cemented paste backfills (LCPB), the unconfined compressive strength (UCS) tests were carried out on LCPB and supplemented with the digital image correlation (DIC) method. The damage characteristics were revealed from the energy perspective, and the damage constitutive equation was established. The results show that the ratio of yield stress to UCS increased with the increase of the c/t ratio and h/H ratio. The intersection point of the dissipation energy and the elastic energy curves could be conservatively considered as a sign that the LCPB is about to enter the accelerated damage stage. The appearance of the intersection point will be earlier with decreasing c/t ratio and increasing h/H ratio. The damage rate curves exhibited an evolutionary characteristic of increasing and then decreasing, and the maximum damage rate gradually decreased with decreasing c/t ratio and increasing h/H ratio; The failure mode showed a significant localization characteristic, and the damage of LCPB was mainly caused by tensile stress generated in the horizontal direction. The findings could provide guidance for the design of LCPB.

Ice slurry pigging technology in drinking water distribution system: From flow mechanisms to pipelines cleaning application

Drinking water distribution systems are prone to (bio)fouling over time, negatively impacting drinking water quality. Ice slurry pigging is a promising technology used to remove solids attached to the inner parts of the pipe walls with ice-water mixture. To understand the ice slurry pigging flow characteristics and optimize its operations, this study presents the development of a Computational Fluid Dynamics model (CFD) combined with the Kinetic Theory of Granular Flow model (KTGF) and a thermal model. Firstly, the model is validated with experimental data from the literature on solid-liquid Two-Phase Flow (TPF), including flow characteristics and thermal effects. Secondly, simulations for a typical ice slurry pigging process show uneven ice phase fraction and shear stress distributions in the main pipe flow and vertical direction. Results indicate that the main limitations of effective pipe cleaning are due to buoyancy and thermal effects. Moreover, ice slurry with 1.0 mm ice particles performs better in providing effective shear stress compared to 0.1 mm, 0.5 mm, and 1.5 mm ice particles. Additionally, the optimal injection ratios of ice slurry with 1.0 mm are determined to be over 0.3 and 0.26 when cleaning pipeline lengths within 500 m and 1000 m, respectively.

DFMC SBAS service performance analysis of multi-GNSS based on BDS-3 in different regions

Abstract The dual-frequency multi-constellation satellite-based augmentation system (DFMC SBAS) plays a crucial role in many fields, such as civil aviation and other safety-critical applications. To analyze the performance of the third generation of the BeiDou navigation satellite system (BDS-3) dual-frequency SBAS services in global major regions and the enhancement of navigation service performance by multi-Global Navigation Satellite System DFMC SBAS, four schemes are designed to conduct experiments using user end positioning in China (CHN), Europe (EUR), and Australia (AUS), and the results are analyzed under Approach with Vertical guidance I (APV-I) and Category I Precision Approach (CAT-I). In terms of the number of enhanced satellites, user range error, positioning accuracy, and DFMC SBAS service integrity, the results show that the positioning performances of the BDS-3 DFMC SBAS in the horizontal and vertical directions are 0.60 and 1.12 m for the CHN region, 0.87 and 1.39 m for the EUR region, and 0.64 and 1.11 m for the AUS region. In the CHN and AUS regions, the horizontal and vertical accuracies are comparable and better than those in the EUR region. Under the APV-I performance index, except for stations at the edge of the service range in the CHN and AUS regions, the availability and continuity of all stations were 100% and over 99% in the EUR region. The BDS-3 + Galileo + GPS DFMC SBAS service can significantly improve the positioning accuracy compared to a single constellation. Under the APV-I performance index, the availability and continuity of all stations in the three regions reached 100%, which also satisfied the minimum requirement of CAT-I service availability (99%).

Liquid-immersion inclined-rotated exposure system for fabricating three-dimensional microstructures with large inclination angles

Abstract This study utilized liquid-immersion inclined-rotated ultraviolet lithography to fabricate three-dimensional (3D) microstructures. The maximum achievable inclination angles obtained through conventional inclined-rotated exposure (IRE) methods were limited by the significant refractive index differences in material. We proposed an IRE with liquid-immersion and adjustable mirrors, which enabled greater inclination angles with improved adjustability. Using liquid as a medium helped minimize the refractive index disparities between materials. We fabricated polydimethylsiloxane molds for micro suction cup (MSC) array sheets to evaluate the performance of the developed liquid-immersion IRE. The resulting MSC array sheets (10 mm2) with a suction cup diameter of 500 μm, achieved inclination angles up to 51°, approximately double those obtained with the conventional IRE method. In addition, the suction force of the fabricated MSC arrays were evaluated by pulling along the vertical, horizontal, and edge directions under wet conditions. The maximum measured suction force was 0.15 N, confirming the effectiveness of the proposed liquid-immersion IRE in fabricating 3D microstructures, as demonstrated by the fabricated MSC array sheets.

Study on mechanical properties of locally corroded square steel tube short column

To investigate the axial compressive properties and failure modes of 18 locally corroded square steel tube short columns, salt spray corrosion tests were conducted. The findings indicate that local corrosion in the horizontal direction significantly impacts the ultimate bearing capacity of the specimens, with all failures occurring in the corroded areas. However, the influence of the corrosion area on the ultimate bearing capacity and ductility of the specimens is not evident. A local corrosion model for square steel tube short columns was developed using the finite element method. The ultimate bearing capacity determined through finite element simulation closely aligns with experimental results, validating the reliability of the simulation approach. Moreover, a comparison is made between the prediction models of the BP neural network and the GA-BP neural network, with the prediction effectiveness of each model evaluated using the leave-one-out method. The verification results indicate that the GA-BP neural network model demonstrates superior predictive performance, with an average error of 3.14%.

Electromagnetic scattering controlled all-dielectric cavity-antenna for bright, directional, and purely radiative single-photon emission

A deterministic, bright, room-temperature stable single-photon source (SPS) has been a major demand in the field of quantum photonics. Here, using computational and analytical techniques, we showed that the Mie-scattering moments of an all-dielectric cavity-cum-antenna help in shaping the spontaneous emission process of an embedded point-dipole emitter, the nanodiamond-based NV− and SiV color centers here. Our resonator-cum-antenna design comprises two top and bottom TiO2 cylinders with a sandwiched polyvinyl alcohol (PVA) layer enclosing the nanodiamond crystal. The Cartesian multi-polar decomposition of the Mie-scattering moments of the sandwiched PVA layer (enclosing the dipole emitter) with subwavelength scale thickness showed strong electric-dipole (ED) resonance. This resulted in significant field confinement, making the PVA layer to act as a cavity, providing a Purcell enhancement of more than an order of magnitude for all dipole orientations. The top and bottom TiO2 cylinders were observed to act as an antenna, and the far-field radiation pattern of the embedded dipole-emitter is controlled by the Mie-scattering moments of the TiO2 cylinders. The radiation directionality along the vertical directions was found to be maximum at the Kerker point (electric dipole moment, ED = magnetic dipole moment), the collection efficiency (CE) being about 80%. For dipole emission coupled to the antenna, the quantum efficiency was observed to increase to a high value of 0.98 for nanodiamond NV− center, very close to an ideal case of purely radiative emission. Our scheme is shown to be universal and can be applied to any solid-state-based quantum emitters, for generating on-demand SPS for quantum-photonic applications.

Response of a Coral Reef Sand Foundation Densified through the Dynamic Compaction Method

Dynamic compaction is a method of ground reinforcement that uses the huge impact energy of a free-falling hammer to compact the soil. This study presents a DC method for strengthening coral reef foundations in the reclamation area of remote sea islands. Pilot tests were performed to obtain the design parameters before official DC operation. The standard penetration test (SPT), shallow plate-load test (PLT), and deformation investigation were conducted in two improvement regions (A1 and A2) with varying tamping energies. During the deformation test, the depth of the tamping crater for the first two points’ tamping and the third full tamping was observed at two distinct sites. The allowable ground bearing capacity at two disparate field sites was at least 360 kPa. The reinforcement depths were 3.5 and 3.2 m in the A1 and A2 zones, respectively. The DC process was numerically analyzed by the two-dimensional particle flow code, PFC2D. It indicated that the reinforcement effect and effective reinforcement depth were consistent with the field data. The coral sand particles at the bottom of the crater were primarily broken down in the initial stage, and the particle-crushing zone gradually developed toward both sides of the crater. The force chain developed similarly at the three tamping energies (800, 1500, and 2000 kJ), and the impact stress wave propagated along the sand particles primarily in the vertical direction.

Twisted cell flow facilitates three-dimensional somite morphogenesis in zebrafish

Tissue elongation is a fundamental morphogenetic process to construct complex embryonic structures. In zebrafish, somites rapidly elongate in both dorsal and ventral directions, transforming from a cuboidal to a V-shape within a few hours of development. Despite its significance, the cellular behaviors that directly lead to somite elongation have not been examined at single-cell resolution. Here, we describe the motion and shapes of all cells composing the dorsal half of the somite in three-dimensional space using lightsheet microscopy. We identified two types of cell movements—in horizontal and dorsal directions—that occur simultaneously within individual cells, creating a complex, twisted flow of cells during somite elongation. Chemical inhibition of Sdf1 signaling disrupted the collective movement in both directions and inhibited somite elongation, suggesting that Sdf1 signaling is crucial for this cell flow. Furthermore, three-dimensional computational modeling suggested that horizontal cell rotation accelerates the perpendicular elongation of the somite along the dorsoventral axis. Together, our study offers novel insights into the role of collective cell migration in tissue morphogenesis, which proceeds dynamically in the three-dimensional space of the embryo.

Identifying Risk Factors for Wound Complications Following Fronto-Orbital Advancement in Patients With Craniosynostosis: 3-dimensional Craniometrics Analysis.

This study aims to identify 3-dimensional (3D) craniometric predictors of wound complications following fronto-orbital advancement (FOA) surgery in craniosynostosis patients. The authors conducted a retrospective review of medical records for 43 patients (25 female, 18 male) who underwent open FOA between 2006 and 2023, with an average follow-up duration of 91.8 months. The data collected included age at surgery, sex, whether the craniosynostosis was syndromic, involvement of multiple sutures, history of suturectomy, wound complications (categorized as minor or major), and preoperative and postoperative 3D CT scans. The authors quantified relative changes in intracranial volume (ICV), cranial area above the Frankfurt Horizontal plane, anteroposterior diameter (APD), and cranial height (CH) using Mimics software. A logistic regression analysis was performed to identify predictors of wound complications post-FOA. Among the 43 patients who underwent FOA, 10 experienced postoperative wound complications (4 minor, 6 major), revealing significant associations with multisuture involvement and changes in △cranial area, △APD, and △CH (all P<0.05). In the multivariable analysis with backward elimination, △cranial area, and △CH were identified as significant risk factors for wound complications (OR 1.17, 95% CI: 1.01-1.36, P=0.032; and OR 0.59, 95% CI: 0.38-0.92, P=0.019, respectively). The cutoff values for △cranial area and △APD were 5.95% and 7.93%, respectively. This study identified measurable craniometric changes, especially in the cranial area, as risk factors for wound complications following FOA. It underscores the necessity for personalized surgical planning and meticulous postoperative wound care in FOA to enhance patient outcomes through risk-aware strategies.

Experimental investigation on the thermal performance of a large-size aluminum vapor chamber for multi-point heat sources

Abstract With the development of electronic information technology, the integration and power of electronic equipment continue to increase. As an efficient heat transfer element, vapor chambers are widely used in the field of heat dissipation of electronic devices. However, greater challenges have been posed in terms of higher heat dissipation capacity, larger size, and lighter weight. Therefore, a large-scale aluminum vapor chamber with a size of 340 mm×295 mm ×7.5 mm is designed for the heat dissipation of multi-point array heat sources. Multiple parallel porous ribs are sintered to form capillary wicking channels and vapor diffusion paths, which efficiently transfer the heat from the middle of the vapor chamber to the cold plate on the two sides. The transient working characteristics and heat dissipation performance under different working conditions are experimentally investigated. The results show that there is obvious temperature instability, which can be suppressed by the tilt of the vapor chamber and the increase of the heating power. Under the tilt condition, the temperature rises in the vertical direction due to the influence of gravity, while the inclination angle has basically no effect. The vapor chamber can work stably at the total heating power of 2100 W with the smallest thermal resistance 0.03 °C/W. The single-point heat flux can reach 7.3W/cm2 for the 128 heat sources. Compared to a traditional vapor chamber, the proposed aluminum vapor chamber provides a thermal management solution for large-size electronic devices with multiple heat sources.

Misalignment‐tolerant coupling cell of 2‐D modular WPT system for charging area simplified extension

Abstract2‐D modular wireless power transfer (WPT) system needs to have stable output when coil misalignment occurs. In order to improve the misalignment tolerance of the system coupling unit, this article proposes a magnetic coupling structure based on the LCC‐S compensation topology by combining a rectangular coil with two sets of mutually orthogonal solenoidal compensation coils. The rectangular coil is used to receive the vertical magnetic flux, and the two sets of compensating coils are used to receive the magnetic flux in the directions of X‐axis and Y‐axis on the horizontal plane, separately. The receiving side of the 2‐D wireless power transmission array cells cascaded half‐bridge rectifiers to connect each group of coils. This arrangement effectively compensates for the voltage drop of the rectangular coil caused by positional offset in any direction, so that the output voltage of the receiving side remains stable. The article firstly establishes the equivalent circuit model of the proposed design and deduces in detail the relationship equations between the output characteristics of the system and each influence factor. Secondly, the magnetic coupling structure is designed by finite element electromagnetic simulation software, and the total equivalent mutual inductance fluctuation of the proposed design is verified to be within 3.9% over the range of 2‐D transmission array cells. Finally, a 150 W experimental platform is built to verify the misaligment‐tolerant of the proposed design in the range of 2‐D transmission array cells. The experimental results show that the output voltage fluctuation of the proposed design within 4.27% at all directional offsets. Moreover, the stable output performance can be obtained in the case of vertical and rotational misalignment.

Tunable High-Static-Low-Dynamic Stiffness Isolator under Harmonic and Seismic Loads

High-Static-Low-Dynamic Stiffness (HSLDS) mechanisms exploit nonlinear kinematics to improve the effectiveness of isolators, preserving controlled static deflections while maintaining low natural frequencies. Although extensively studied under harmonic base excitation, there are still few applications considering real seismic signals and little experimental evidence of real-world performance. This study experimentally demonstrates the beneficial effects of HSLDS isolators over linear ones in reducing the vibrations transmitted to the suspended mass under near-fault earthquakes. A tripod mechanism isolator is presented, and a lumped parameter model is formulated considering a piecewise nonlinear–linear stiffness, with dissipation taken into account through viscous and dry friction forces. Experimental shake table tests are conducted considering harmonic base motion to evaluate the isolator transmissibility in the vertical direction. Excellent agreement is observed when comparing the model to the experimental measurements. Finally, the behavior of the isolator is investigated under earthquake inputs, and results are presented using vertical acceleration time histories and spectra, demonstrating the vibration reduction provided by the nonlinear isolator.

Deep Learning-Based Flood Detection for Bridge Monitoring Using Accelerometer Data

Flooding and consequential scouring are the primary causes of bridge failures, making the detection of such events crucial for structural safety. This study investigates the characteristics of accelerometer data from bridge pier vibrations and proposes a flood detection method with deep learning-based models based on ResNet18 and 1D Convolution architectures. These models were comprehensively evaluated for (1) detecting vehicles passing on bridges and (2) detecting flood events based on axis-specific accelerometer data under various traffic conditions. Continuous Wavelet Transform (CWT) was employed to convert the accelerometer data into richer time-frequency representations, enhancing the detection of passing vehicles. Notably, when vehicles are passing over bridges, the vertical direction exhibits a magnified and more sustained energy distribution across a wider frequency range. Additionally, under flooding conditions, time-frequency representations from the bridge direction reveal a significant increase in energy intensity and continuity compared with non-flooding conditions. For detection of vehicles passing, ResNet18 outperformed the 1D Convolution model, achieving an accuracy of 97.2% compared with 91.4%. For flood detection without vehicles passing, the two models performed similarly well, with accuracies of 97.3% and 98.3%, respectively. However, in scenarios with vehicles passing, the 1D Convolution model excelled, achieving an accuracy of 98.6%, significantly higher than that of ResNet18 (81.6%). This suggests that high-frequency signals, such as vertical vibrations induced by passing vehicles, are better captured by more complex representations (CWT) and models (e.g., ResNet18), while relatively low-frequency signals, such as longitudinal vibrations caused by flooding, can be effectively captured by simpler 1D Convolution over the original signals. Consequentially, the two model types are deployed in a pipeline where the ResNet18 model is used for classifying whether vehicles are passing the bridge, followed by two 1D Convolution models: one trained for detecting flood events under vehicles-passing conditions and the other trained for detecting flood events under no-vehicles-passing conditions. This hierarchical approach provides a robust framework for real-time monitoring of bridge response to vehicle passing and timely warning of flood events, enhancing the potential to reduce bridge collapses and improve public safety.

Network analysis of three-dimensional hard-soft tissue relationships in the lower 1/3 of the face: skeletal Class I-normodivergent malocclusion versus Class II-hyperdivergent malocclusion

BackgroundThe determining effect of facial hard tissues on soft tissue morphology in orthodontic patients has yet to be explained. The aim of this study was to clarify the hard-soft tissue relationships of the lower 1/3 of the face in skeletal Class II-hyperdivergent patients compared with those in Class I-normodivergent patients using network analysis.MethodsFifty-two adult patients (42 females, 10 males; age, 26.58 ± 5.80 years) were divided into two groups: Group 1, 25 subjects, skeletal Class I normodivergent pattern with straight profile; Group 2, 27 subjects, skeletal Class II hyperdivergent pattern with convex profile. Pretreatment cone-beam computed tomography and three-dimensional facial scans were taken and superimposed, on which landmarks were identified manually, and their coordinate values were used for network analysis.Results(1) In sagittal direction, Group 2 correlations were generally weaker than Group 1. In both the vertical and sagittal directions of Group 1, the most influential hard tissue landmarks to soft tissues were located between the level of cemento-enamel junction of upper teeth and root apex of lower teeth. In Group 2, the hard tissue landmarks with the greatest influence in vertical direction were distributed more forward and downward than in Group 1. (2) In Group 1, all the correlations for vertical-hard tissue to sagittal-soft tissue position and sagittal-hard tissue to vertical-soft tissue position were positive. However, Group 2 correlations between vertical-hard tissue and sagittal-soft tissue positions were mostly negative. Between sagittal-hard tissue and vertical-soft tissue positions, Group 2 correlations were negative for mandible, and were positive for maxilla and teeth.ConclusionCompared with Class I normodivergent patients with straight profile, Class II hyperdivergent patients with convex profile had more variations in soft tissue morphology in sagittal direction. In vertical direction, the most relevant hard tissue landmarks on which soft tissue predictions should be based were distributed more forward and downward in Class II hyperdivergent patients with convex profile. Class II hyperdivergent pattern with convex profile was an imbalanced phenotype concerning sagittal and vertical positions of maxillofacial hard and soft tissues.

Three-dimensional assessment of low-level laser therapy on orthodontic miniscrew displacement using CBCT: a retrospective study

BackgroundThis study aimed to assess the effect of Low-Level Laser Therapy (LLLT) on sagittal, transverse and vertical Orthodontic miniscrew displacement.Materials and methodsThe study included CBCTs from the records of 12 adult patients who underwent upper first premolar extraction and canine retraction with orthodontic miniscrews for maximum anchorage. The miniscrews on one side received LLL, while the other side served as a control. The Low-Level Laser was applied to assess its effect on the displacement of the miniscrews. The used CBCTs have been taken at two-time points: immediately after miniscrew insertion (T0) and four months after the start of canine retraction (T1) with a total of 24 CBCTs. Miniscrew displacement was assessed by measuring head (HMS) and tail (TMS) displacement to the axial, coronal and mid-sagittal planes on the CBCT at the two time points. Miniscrews displacement (T1-T0) was compared between LLL side and control side. Comparisons were performed using paired samples t-test. The significance level was set at p-value < 0.05. The reproducibility of measurements was assessed by intraclass correlation coefficient (ICC).ResultsAfter four months of canine retraction, HMS and TMS from both laser and control sides showed significant three-dimensional displacement at p < 0.05. No significant difference in mean displacement in the vertical, sagittal, nor transverse planes between both sides was elicited.ConclusionLLL application in the used protocol does not affect the amount of miniscrew displacement in any of the three planes of space. Miniscrew displacement was significant in both groups.