Homogeneous Adsorption Research Articles

Synthesis of ion exchange film based on chemical grafting of styrene onto polyethylene/EPDM rubber blend for thorium removal.

Chemical grafting of low-density polyethylene film blended with ethylene propylene diene monomer rubber (PE/EPDM) using styrene monomer followed by a sulfonation process was investigated. Different factors affecting the grafting process, such as monomer and initiator concentrations, time of reaction, and grafting temperature, were studied. Sulfonation of the grafted films was carried out using chlorosulfonic acid in dichloromethane. Characterization of the grafted and sulfonated films was performed using ATR-FTIR, SEM, TGA, and XRD instruments. The grafting was successfully performed in aqueous media using sodium bisulfite as initiator, reaching a grafting yield of 130% and an ion exchange capacity of 1.2 meq/g. The removal of thorium ions from aqueous solution was studied using the obtained ion exchange films. The results showed that the maximum adsorption capacity of Th(IV) was 177.5 mg. g-1 (pH = 3, 298 K and 60 min). Removal isotherm and Kinetics were investigated, and the results revealed that the adsorption process was chemisorption homogeneous monolayer adsorption, exothermic, and spontaneous.

Waste glass as a source for green synthesis of mesoporous adsorbent for efficient removal of heavy metals

Mesoporous analcime Adsorbent (MaA) was cogently synthesized in a hydrothermal reaction where a waste silica glass powder was mixed into NaOH solution. The satisfactory reaction properties were achieved by regulating the conditioning time (Ct), reaction temperature (Rt), and relative ratio of the reactants (Rr= SiO2:Na2O). XRF, XRD, SEM, BET, FTIR, AFM, TG and TEM analysis formed part of the selected samples. The prepared MaA adsorbent was then applied to treat Pb2+, Cd2+ and Cu2+ ions, thus effectively allowing the physicochemical properties (pH, temperature and contact duration), on the adsorption amount to be examined. Upon completion, the results indicated that the initial pH as well as the contact duration had notable effect on the adsorption amount. Conversely, the temperature change had an insignificant effect on the equilibrium adsorption amount. In addition, a dosage of 0.1 g of MaA, concentration of 1000 mg/L, pH ranging from 6−8, and temperature of about 25°C were found to be the optimum process conditions for the adsorption of the examined heavy metals, whereas difference in contact time was recorded as follows: 1 h for Pb2+ and Cu2+ ions with adsorption amounts of 75.081 mg/g and 74.054 mg/g, respectively; and 3 h for Cd2+ ion with adsorption equal to 75.530 mg/g. In the analysis of the trend, the coefficients of correlation (R2=0.99) of the Langmuir isotherm model were increasingly consistent compared to Freundlich isotherm model (R2 from 0.10 to 0.55), thus indicating that the process to be a homogeneous monomolecular layer adsorption. Moreover, the kinetic aspects were similarly consistent in relation to quasi-secondary kinetic equation, which then further established that the process was primarily controlled by ion exchange, extra-particle, intra-particle, and liquid film diffusion. In addition, research on the potential reusability of MaA adsorbent after being employed to treat heavy metals was also performed. The crystalline phase of the composite after subjected to high temperature indicated wollastonite (CaSiO₃) and gregoryite (Na₂CO₃) as the main mineralogical phases. These minerals are beneficial in the preparation of functional building materials by promoting a sustainable solution for the full recycling of waste glass and contributing to efficient solid waste management and environment protection.

Adsorption Performance of Modified Graphite from Synthetic Dyes Solutions.

Due to the severe harmful impacts of industrial dyeing wastewater on ecosystems and human health, proper treatment is crucial. Herein, the use of modified graphite as an adsorbent for dyeing wastewater treatment was investigated in this study. The graphite was oxidized and intercalated using a phosphoric acid-nitric acid-potassium permanganate system and then thermally treated at high temperatures to optimize its structure. By adjusting the thermal treatment temperature, the graphite adsorbent with varying porosity was obtained. The optimized graphite demonstrated significant improvement in adsorption performance for dyes and organic compounds, achieving a removal rate of over 85% for methylene blue (MB) dye. The optimal adsorption performance is achieved with a 1.6 mg modified graphite adsorbent at 60 °C under alkaline conditions for adsorbing 10 ppm MB. Adsorption kinetics and isotherm models were applied to elucidate the adsorption mechanisms. The results fit the Langmuir model, suggesting that monolayer homogeneous adsorption is favorable. Importantly, the results demonstrate that high-temperature treatment can significantly enhance the adsorption properties of coal-based graphite, supporting its application in dyeing wastewater treatment.

Sodium alginate/banana peels/reduced graphene oxide nanocomposite beads for effective removal of copper and nickel from aqueous solutions

The use of naturally derived nanocomposite beads to remove nickel and copper is gaining more attention due to its relative abundance, low toxicity, and strong affinity toward heavy metals. Most previous studies focus on removing single heavy metals using developed nanocomposite beads. This work prepared sodium alginate/banana peels/reduced graphene oxide nanocomposite beads through simple precipitation using banana peels, reduced graphene oxide, and sodium alginate. The formed nanocomposite beads were characterized and evaluated for the adsorption of nickel and copper from the aqueous phase at neutral pH. The Langmuir isotherm suggests the homogenous adsorption of metals on the surface of the bead. The maximum removal capacity is 85.32 mg/g and 95.79 mg/g for nickel and copper, respectively. This study provides new insight into utilizing banana peels, reduced graphene oxide, and sodium alginate for toxic metal remediation to overcome pollution problems.

Effective Removal of Cu(II) Ions from Aqueous Solution by Cross-Linked Chitosan-Based Hydrogels

The elimination of metal ions from industrial waste water is one of the most significant environmental needs. For the first time, two chitosan hydrogels that we had previously synthesized, cross-linked with varying concentrations of trimellitic anhydride isothiocyanate (represented by H1 and H2), were utilized in this investigation to adsorb Cu(II) ions. We found that pH 6, 25 °C, 200 mg L−1 of Cu(II) ions concentration, and 15 mg of hydrogel dosage were the ideal parameters for Cu(II) ion elimination. The kinetics of their adsorption fitted to the pseudo-second-order model with the highest correlation coefficient (R2) values equal to 0.999 and 1.00 for H1 and H2, respectively. The experimental qe values were found when H1 was equal to 97.59 mg g−1 (theoretical value is equal to 98.04 mg g−1) and H2 was equal to 96.20 mg g−1 (theoretical value is equal 99.01 mg g−1). The hydrogels achieved a removal effectiveness of 97.59% and their adsorption isotherms matched the Freundlich model, indicating the multi-layered and homogeneous adsorption nature. The removal of copper ions is significantly driven by the physisorption phenomenon. The hydrogels have a great possibility to be utilized as promising, efficacious, reusable adsorbents for industrial wastewater remediation. Thus, incorporation of a cross-linker, containing binding centers for Cu(II) ions, between chitosan chains is a good way to obtain suitable efficient adsorbents which are good choices for application in the field of metal elimination.

Efficient removal of Cr(VI) ions from industrial wastewater using carbon-based adsorbents functionalized with boronic acid

Abstract The adsorption of potentially toxic element ions from contaminated water sources has garnered significant attention due to its critical role in environmental remediation and ensuring safe drinking water. Potentially toxic element ions can be removed from water using conventional adsorbents such as activated zeolites; however, these materials have low absorption and slow kinetics. To solve these issues, carbon-based adsorbents that exhibit easy synthesis, high porosity, designability, and stability have been proposed. In this study, a carbon-based adsorbent, named Magnetic Nitrogen-Doped Carbon (M-NC), and graphene oxide were developed for the selective removal of potentially toxic element ions. To increase the potential for HM immobilization, sulfide-modified biochar was created via a process called simultaneous carbon layer encapsulation. A theoretical physicochemical and thermodynamic investigation of the adsorption of potentially toxic elements s Zn2+, Cd2+, Ni2+, Ag2+, Pb2+ and Cu2+ on carbon-based adsorbents was performed with statistical physics fundaments. The biochar with large surface areas is used to remove potentially toxic element ions, one of the most important potentially toxic element pollutants, from aqueous solutions. The capacity of the adsorbent for removing potentially toxic element ions was studied using Langmuir adsorption isotherm under ultrasound-assisted conditions. The MNCs can be applied to the Langmuir model and pseudo-second-order kinetics. It is possible to use the Langmuir and second-order kinetic equations to accurately explain the adsorption method. Thermodynamic limitations were also envisioned because sorption is exothermic when it happens spontaneously. A homogeneous statistical physics adsorption model was used to describe and analyze the experimental potentially toxic element removal isotherms at 30 °C and pH5 utilizing adsorbents produced by pyrolysis of biomasses (broccoli stalks). The findings show the proposed adsorbent, with an efficiency of 98.7 % and even reaching 99.3 % in certain cases, making it a standout choice for potentially toxic element removal applications. This research holds significance in advancing the understanding of environmentally sustainable potentially toxic element removal processes, particularly in the context of biomass-derived adsorbents, offering potential solutions for water purification and environmental remediation.

Elaboration of a new Activated Carbon derived from the Crown of Oak (ACOW) to removal the toxic Iodine: Kinetic, Isotherms modelling and Thermodynamics Study

ABSTRACT The current study aims to develop a new adsorbent material using oak crown and explore its effectiveness in removing I2 ions through a series of batch experiments. ACOW was characterised by zero charge (pHpzc) and FTIR spectroscopy. The impact of the initial I2 concentration (20-100 mg/L), temperature (25-55 °C), pH (2-14), adsorbent dosage (2-10 g/L), Stirring speed (100-900 rpm), particle size (100-2000μm) and contact time (0-30 min) on I2 adsorption was examined. The adsorption kinetic obeys the pseudo-second order model with a determination coefficient (R2) equal to 0.999. Adsorption follows the Langmuir equation well, with the best fit to the experimental data at equilibrium. A qmax value (= 103.606 mg/g) at 25°C and 120.773 mg/g at 55°C were eliminated under the optimised conditions, indicating homogeneous adsorption on the surface of the adsorbent. The thermodynamic parameters gave a negative free energy ΔGo (-3.445 to -5.629 kJ/mol), a positive enthalpy ΔHo (18.406 kJ/mol) and an activation energy Ea (= 22.599 kJ/mol), thus confirming the spontaneous and endothermic nature of adsorption of iodine on ACOW. The positive entropy ΔSo (0.0733 kJ/mol K) show increased randomness of the solid-liquid interface during the adsorption.

Cu–Co bimetallic organic framework as effective adsorbents for enhanced adsorptive removal of tetracycline antibiotics

In this study, the removal effect of a new MOF-on MOF adsorbent based on Cu–Co bimetallic organic frameworks on tetracycline antibiotics (TCs) in water system was studied. The adsorbent (Cu-MOF@Co-MOF) were synthesized by solvothermal and self-assembly method at different concentrations of Co2+/Cu2+. The characterization results of SEM, XRD, XPS, FTIR and BET indicated that the MOF-on MOF structure of Cu-MOF@Co-MOF exhibited the best recombination and physicochemical properties when the molar ratio of Co2+: Cu2+ is 5:1. In addition, the Cu-MOF@Co-MOF have a high specific surface area and bimetallic clusters, which can achieve multi-target synergistic adsorption of TCs. Based on above advantages, Cu-MOF@Co-MOF provided a strong affinity and could efficiently adsorb more than 80% of pollutants in just 5 to 15 min using only 10 mg of the adsorbent. The adsorption capacity of tetracycline and doxycycline was 434.78 and 476.19 mg/g, respectively, showing satisfactory adsorption performance. The fitting results of the experimental data were more consistent with the Langmuir isotherm model and pseudo-second-order kinetic model, indicating that the adsorption process of TC and DOX occurred at the homogeneous adsorption site and was mainly controlled by chemisorption. Thermodynamic experiments showed that Cu-MOF@Co-MOF was thermodynamically advantageous for the removal of TCs, and the whole process was spontaneous. The excellent adsorption capacity and rapid adsorption kinetics indicate the prepared MOF-on MOF adsorbent can adsorb TCs economically and quickly, and have satisfactory application prospects for removing TCs in practical environments. The results of the study pave a new way for preparing novel MOFs-based water treatment materials with great potential for efficient removal.

Adsorption of heavy metal ions by carbon-based adsorbent using magnetic nitrogen-doped carbon and graphene oxide

ABSTRACT The adsorption of weighty metal particles from contaminated water sources has garnered significant attention due to its critical role in environmental remediation and ensuring safe drinking water. Heavy metal ions can be removed from water using conventional adsorbents such as activated zeolites; however, these materials have low absorption and slow kinetics. To solve these issues, carbon-based adsorbents that exhibit easy synthesis, high porosity, design ability, and stability have been proposed. In this review, a carbon-based adsorbent, named M-NC, and graphene oxide were created for the particular evacuation of weighty metal particles. To increase the potential for Heavy Metals (HM) immobilization, sulfide-modified biochar was created via a process called synchronous carbon layer epitome. A hypothetical physicochemical and thermodynamic examination of the adsorption of weighty metals Zn2+, Cd2+, Ni2+, Ag2+, Pb2+ and Cu2+ on carbon-based adsorbents was done with factual material science fundaments. The biochar with large surface areas is utilized to eliminate weighty metal particles, quite possibly the most significant heavy metal pollutants, from aqueous solutions. The limit of the adsorbent for eliminating weighty metal ions was concentrated on utilizing Langmuir adsorption isotherm under ultrasound-helped conditions. The Mesoporous Silica Nanoparticles (MNCs) can be applied to the Langmuir model and pseudo-second-order kinetics. It is possible to use the Langmuir and second-order kinetic equations to accurately explain the adsorption method. Thermodynamic limitations were also envisioned because sorption is exothermic when it happens spontaneously. A homogeneous measurable physical science adsorption typically was utilized to describe and analyze the experimental heavy metal removal isotherms at 30°C and pH5 utilizing adsorbents produced by pyrolysis of biomasses (broccoli stalks). The experimental results were investigated in terms of Langmuir and pseudo-2nd-order kinetic equations, Freundlich and isotherm models. The outcome of pH, initial heavy metal ion concentration, contact time, and adsorbent dosage regarding the adsorption capacity and removal efficiency of Pb2+ and Cd2+ on the hydrogel was examined. This study contributes to the advancement of information in the ground of environmentally friendly heavy metal removal techniques, specifically focusing on the usage of biomass-based adsorbents. These findings have the potential to address the need for effective solutions in water purification and environmental cleanup efforts.

Adsorption behavior and mechanism of Cu(II) by sodium alginate/carboxymethylcellulose/magnesium hydroxide (SC-MH) hydrogel

In the present work, an environmentally-friendly, reusable hydrogel ball characterized by its great adsorption capacity to Cu(II) was synthesized. The preparation of this hydrogel drew on sodium alginate (SA) and carboxymethyl cellulose (CMC) as primary composition elements. The endeavor brought novelty by ingeniously infusing it with slurry magnesium hydroxide (MH). The factors (pH, SC-MH amount, initial concentration, adsorption time) that are critical to adsorption were also investigated. FTIR, SEM-EDS and XPS were used to reveal the adsorption mechanism of Cu on SC-MH. The results show that the surface of SC-MH is rough, and there are a large number of gully-like structures conducive to adsorption, which are rich in hydroxyl and carboxyl groups. Under the optimum conditions, the maximum adsorption capacity reached 215.68 mg/g. Based on its high R2 value (0.999), the Langmuir model is determined to be the most appropriate for describing the adsorption behavior, indicating monolayer homogeneous adsorption. The kinetic data align well with the pseudo-second-order kinetic model. Furthermore, thermodynamic analysis reveals the adsorption process to be spontaneous and endothermic, as demonstrated by a negative ΔG and positive ΔH (38.8859 KJ/mol). The mechanism involves electrostatic attraction, chelation, Mg(OH)2 adsorption and ion exchange.

A sustainable and economical solution for CO2 capture with biobased carbon materials derived from palm kernel shells.

This study investigates the synthesize of activated carbon for carbon dioxide adsorption using palm kernel shell (PKS), a by-product of oil palm industry. The adsorbent synthesis involved a simple two-step carbonization method. Firstly, PKS was activated with potassium oxide (KOH), followed by functionalization with magnesium oxide (MgO). Surface analysis revealed that KOH activated PKS has resulted in a high specific surface area of 1086 m2/g compared to untreated PKS (435 m2/g). However, impregnation of MgO resulted in the reduction of surface area due to blockage of pores by MgO. Thermogravimetric analysis (TGA) demonstrated that PKS-based adsorbents exhibited minimal weight loss of less than 30% up to 500 °C, indicating their suitability for high-temperature applications. CO2 adsorption experiments revealed that PKS-AC-MgO has achieved a higher adsorption capacity of 155.35 mg/g compared to PKS-AC (149.63 mg/g) at 25 °C and 5 bars. The adsorption behaviour of PKS-AC-MgO was well fitted by both the Sips and Langmuir isotherms, suggesting a combination of both heterogeneous and homogeneous adsorption and indicating a chemical reaction between MgO and CO2. Thermodynamic analysis indicated a spontaneous and thermodynamically favourable process for CO2 capture by PKS-AC-MgO, with negative change in enthalpy (- 0.21 kJ/mol), positive change in entropy (2.44 kJ/mol), and negative change in Gibbs free energy (- 729.61 J/mol, - 790.79 J/mol, and - 851.98 J/mol) across tested temperature. Economic assessment revealed that the cost of PKS-AC-MgO is 21% lower than the current market price of commercial activated carbon, indicating its potential for industrial application. Environmental assessment shows a significant reduction in greenhouse gas emissions (381.9 tCO2) through the utilization of PKS-AC-MgO, underscoring its environmental benefits. In summary, the use of activated carbon produced from PKS and functionalised with MgO shows great potential for absorbing CO2. This aligns with the ideas of a circular economy and sustainable development.

Removal of acetaminophen from wastewater using a novel bimetallic La/Th metal-organic framework: Kinetics, thermodynamics, isotherms, and optimization through Box-Behnken design

Acetaminophen (ACT), a common drug pollutant, has been effectively removed from wastewater by a novel adsorbent called La/Th-MOF. This adsorbent is made of stacked nanorods of 2-methyl imidazole with lanthanum and thorium. La/Th-MOF, which is characterized by sophisticated techniques including SEM, XRD, and BET analysis, has a mesoporous assembly with a 1.23 nm pore size and a capacious surface area of 2226.93 m2/g, which facilitates effectual adsorption. The adsorption tests, which were impacted by factors such as pH levels, ACT concentration, and contact time, fit into a pseudo-second-order chemisorption kinetic model and with the Langmuir isotherm, suggesting homogenous monolayer adsorption. The material in question demonstrated a noteworthy maximum adsorption capability of 339.75 mg/g for ACT, indicating its probable as a feasible and economical adsorbent for the mitigation of pharmaceutical contamination in wastewater. Our results designate that pH levels have an important influence on the efficacy of ACT absorption by La/Th-MOF, with an acidic pH 5 environment being most favorable for maximal adsorption at a material dosage of 0.02 g. It was discovered that the adsorption procedure was endothermic. Using pseudo-second-order kinetic models and the Langmuir isotherm, which both fit the experimental data very well, to explain the adsorption kinetics. A chemisorption mechanism was found to be predominant throughout the process, as specified by the predicted adsorption energy of 22.62 kJ/mol. In addition, optimized the influencing parameters by using the Box-Behnken design (BBD) and response surface methodology (RSM), which improved process efficiency. La/Th-MOF, has a remarkable half-life, as demonstrated by six rounds of adsorption and desorption without a discernible decline in performance. Research endeavors aimed at elucidating the interplay between La/Th-MOF and ACT hint to several plausible points of contact that could contribute to the adsorption procedure, such as hydrogen bonding, π-π interactions, pore filling or electrostatic forces. This study, which is innovative in its use, reveals the exceptional efficacy of La/Th-MOF in wastewater purification using ACT extraction. An astounding 339.75 mg/g of optimal adsorption capability was attained at an acidic pH of 5. This highlights how the La/Th-MOF can be used in practice to treat pharmaceutical pollutants found in water sources.

Adsorption behaviors and mechanisms of porous polyvinyl alcohol/xanthan gum hydrogel for methylene blue and Pb2+

Faced with extensive water pollution caused by dyes and heavy metals, it is imperative to create cost-effective adsorbents that can effectively eliminate residual pollutants in wastewater. The synthesis of polyvinyl alcohol/xanthan gum (PVA/XG) hydrogels involved a combination of freeze-thaw cycling technique and the adsorption characteristics and mechanisms of methylene blue (MB) and heavy metal ions Pb2+ were investigated. In comparison to pure PVA hydrogels, the swelling behavior of PVA/XG3 hydrogel exhibited a 185 % increase in swelling rate. The adsorption test results suggested that PVA/XG3 hydrogel was effective in absorbing MB (27.39 mg/g) and Pb2+ (17.07 mg/g) from a 50 mg/L pollutant solution. The adsorption process of MB and Pb2+ by PVA/XG3 hydrogel followed Langmuir adsorption isotherm and the QFO models, indicating a preference for homogeneous physical adsorption. Specifically, the Langmuir isothermal model predicted that the qmax of MB and Pb2+ by PVA/XG3 hydrogel were 94.47 and 58.50 mg/g, respectively. Therefore, this essay has created a cost-effective and environmentally friendly method for producing versatile PVA/XG hydrogels specifically intended for water treatment purposes.

Homogeneous Adsorption of Multiple Potassiation Products of Red Phosphorus Anode toward Stable Potassium Storage.

Potassium ion batteries (PIBs) are a viable alternative to lithium-ion batteries for energy storage. Red phosphorus (RP) has attracted a great deal of interest as an anode for PIBs owing to its cheapness, ideal electrode potential, and high theoretical specific capacity. However, the direct preparation of phosphorus-carbon composites usually results in exposure of the RP to the exterior of the carbon layer, which can lead to the deactivation of the active material and the production of "dead phosphorus". Here, the advantage of the π-π bond conjugated structure and high catalytic activity of metal phthalocyanine (MPc) is used to prepare MPc@RP/C composites as a highly stable anode for PIBs. It is shown that the introduction of MPc greatly improves the uneven distribution of the carbon layer on RP, and thus improves the initial Coulombic efficiency (ICE) of PIBs (the ICE of FePc@RP/C is 75.5% relative to 62.9% of RP/C). The addition of MPc promotes the growth of solid electrolyte interphase with high mechanical strength, improving the cycle stability of PIBs (the discharge-specific capacity of FePc@RP/C is 411.9 mAh g-1 after 100 cycles at 0.05 A g-1). Besides, density functional theory theoretical calculations show that MPc exhibits homogeneous adsorption energies for multiple potassiation products, thereby improving the electrochemical reactivity of RP. The use of organic molecules with high electrocatalytic activity provides a universal approach for designing superior high-capacity, large-volume expansion anodes for PIBs.

Efficient U(VI) removal from aerobic solution by synergistic interaction of nano zero-valent iron with g-C3N4 and assessment of toxicity to microorganism

The graphitic carbon nitride (g-C3N4) supported nano zero-valent iron (nZVI) composites (g-Fe) were synthesized to assess the performance of U(VI) removal and bacterial inactivation. Under aerobic conditions at pH 6.0, 97.0 % of U(VI) was removed within 60 min, while only 7.2 % or 22.6 % of U(VI) were removed by pristine g-C3N4 or nZVI. Effects of operating parameters (pH, temperature, initial U(VI) concentration, and g-Fe dosage) on U(VI) removal were also studied under aerobic conditions. The U(VI) adsorption followed a pseudo-second-order kinetic model, and the adsorption process was in accordance with the Langmuir adsorption isotherm model. This indicated that the removal of U(VI) by g-Fe was a chemisorption and homogeneous monolayer adsorption process. The maximum removal capacity of U(VI) was 952.38 mg/g at pH = 6.0. The absorbed uranium on the g-Fe composite were confirmed to be solely U(VI) under aerobic conditions, while both U(VI) and U(IV) were observed under anaerobic conditions. Hence, adsorption rather than reduction serves as the primary mechanism for U(VI) removal in aerobic environments. Escherichia coli or Bacillus subtilis could be inactivated by nZVI and g-Fe composite, but the biotoxicity of g-Fe was much lower than nZVI. Physical isolation reduced the biotoxicity of nZVI, and the residual biotoxicity of nZVI after excluding physical contact should be ascribed to oxidative stress or free reactive oxidative species (ROS). The biotoxicity of g-Fe was irrelevant to physical isolation, proving that oxidative stress or free ROS might dominate the inactivation mechanisms. The g-Fe composite, an eco-friendly, facile and sustainable material, can be developed for U(VI) removal from radioactive wastewater.

Congo red dye reduction mediated by the electron (e−) transfer route of BH4 − ions using synthesized NiCo2O4/rGO hybrid nanosheets

The treatment of toxic organic pollutants is extremely important for the conservation of clean air, soil, and water. In this study, (reduced graphene oxide) NiCo2O4/ rGO hybrid nanocomposite was prepared by a facile hydrothermal technique and employed for organic dye adsorption from wastewater. The synthesized NiCo2O4/rGO hybrid nanocomposite was studied using FTIR, XRD, SEM, TEM, BET, Raman spectroscopy, and UV–visible. The physical characterizations prove the deposition of NiCo2O4 particles on the rGO surface. The transmission electron microscope image demonstrated that the NiCo2O4 particles with an average size of ∼46 nm was dispersed on the rGO surface. The obtained nanoparticles show a higher specific surface area of 56.4 m2 g−1. Adsorption dynamics as investigated by time and concentration variation show that the adsorption data follows pseudosecond order kinetics and the Langmuir isotherm model, with a maximum adsorption capacity of 106.2 mg g−1, indicating homogeneous physiochemical adsorption of CR dye on the adsorbent surface. Besides, the catalytic effectiveness of synthesized nanocomposite towards Congo red (CR) dye reduction mediated by the electron (e−) transfer route of BH4 − ions was explained in detail. The electrostatic interaction used between the NiCo2O4/rGO hybrid composite and Congo red increased the adsorption ion effectiveness of the dye sample.

Green algae Ulva lactuca-derived biochar-sulfur improves the adsorption of methylene blue from water

The present investigation explores the efficacy of green algae Ulva lactuca biochar-sulfur (GABS) modified with H2SO4 and NaHCO3 in adsorbing methylene blue (MB) dye from aqueous solutions. The impact of solution pH, contact duration, GABS dosage, and initial MB dye concentration on the adsorption process are all methodically investigated in this work. To obtain a thorough understanding of the adsorption dynamics, the study makes use of several kinetic models, including pseudo-first order and pseudo-second order models, in addition to isotherm models like Langmuir, Freundlich, Tempkin, and Dubinin–Radushkevich. The findings of the study reveal that the adsorption capacity at equilibrium (qe) reaches 303.78 mg/g for a GABS dose of 0.5 g/L and an initial MB dye concentration of 200 mg/L. Notably, the Langmuir isotherm model consistently fits the experimental data across different GABS doses, suggesting homogeneous adsorption onto a monolayer surface. The potential of GABS as an efficient adsorbent for the extraction of MB dye from aqueous solutions is highlighted by this discovery. The study’s use of kinetic and isotherm models provides a robust framework for understanding the intricacies of MB adsorption onto GABS. By elucidating the impact of various variables on the adsorption process, the research contributes valuable insights that can inform the design of efficient wastewater treatment solutions. The comprehensive analysis presented in this study serves as a solid foundation for further research and development in the field of adsorption-based water treatment technologies.

Adsorption simulation of 2,4-D pesticide on novel zinc-based 2-amino-4-(1H-1,2,4-triazole-4-yl)benzoic acid coordination complexes using machine learning approach.

The capacity of zinc-based 2-amino-4-(1H-1,2,4-triazole-4-yl)benzoic acid coordination complex (Zn(NH2-TBA)2) and modified Zn(NH-TBA)2COMe complex for removal of 2,4-dichlorophenoxyacetic acid (2,4-D) from aqueous solutions was investigated through adsorption modeling and artificial intelligence tools. Analyzing the adsorption characteristics of pesticides helps in studying the groundwater pollution by pesticides in agriculture area.In this study, Zn(NH2-TBA)2 was synthesized using Schiff base and its surface was modified using acetic anhydride group and their physical characteristics were identified using proton NMR, FTIR, and XRD. NMR results showed maximum modification yield obtained was 65% after 5days. The porous structure and surface area monitored using nitrogen isotherm and BET surface area analysis presented relatively less surface area and porosity after modification. Adsorption modelling indicated that Toth model with a maximum adsorption capacity of 150.8mg/g and 100.7mg/g represents the homogenous adsorption systems which satisfy both low- and high-end boundary of adsorbate concentration in all settings according to the optimum point, while the kinetics and rate of 2,4-D adsorption follow the pseudo-first-order kinetic model in all situations. Artificial neural network (ANN), support vector regression, and particle swarm optimized least squares-support vector regression (PSO-LSSVR) were used for the optimization and modelling of adsorbent mass, adsorbate concentration, contact time, and temperature to develop predictive equations for the simulation of the adsorption efficiency of 2,4-D pesticide. The obtained results exhibited the better performance of ANN and PSO-LSSVR for prediction of adsorption results. The mean square error values of ANN (0.001, 0.012) and PSO-LSSVR (0.121, 0.105) were obtained for Zn(NH2-TBA)2 and Zn(NH-TBA)2COMe, respectively, while their respective coefficient of determination (R2) obtained were 0.999 and 0.988 for ANN and 0.980 and 0.825 for PSO-LSSVR. The study specified that machine learning predictive behavior performed better for Zn(NH2-TBA)2 compared to Zn(NH-TBA)2COMe that is also supported by theoretical kinetics and isotherm models. The research concludes that artificial intelligence models are the most efficient tools for studying the predictive behavior of adsorption data.

Study of the Adsorption and Separation Behavior of Scandium and Zirconium by Trialkyl Phosphine Oxide-Modified Resins in Sulfuric and Hydrochloric Acid Media.

Zirconium is recognized as one of the main impurities of the rare earth element scandium during purification. It presents significant challenges due to its similar chemical properties, making separating it difficult. This study used trialkyl phosphine oxide (TRPO) as a functional ligand, and the effects of carrier type and acidity on adsorption performance were first investigated. Among these, the novel extraction resin SiO2-P as a carrier for TRPO demonstrated more prominent separation performance in 0.2 M H2SO4 and 5 M HCl solutions. The kinetic and isotherm data were consistent with the pseudo-secondary kinetics and Langmuir model, respectively, and the adsorption process could be regarded as homogeneous monolayer adsorption subject to the dual effects of chemisorption and internal diffusion. In addition, thermodynamic analysis showed that the adsorption process of zirconium under the experimental conditions was a spontaneous endothermic process. Combined with the results of SEM-EDS, FT-IR, and XPS analyses, scandium and zirconium were successfully adsorbed by the resin and uniformly distributed on its surface, and the greater affinity of the P=O groups on the resin for zirconium was the critical factor contributing to the separation of scandium and zirconium. Finally, scandium and zirconium in sulfuric acid and hydrochloric acid media were extracted and separated by column experiments, and the purity of scandium could reach 99.8% and 99.99%, respectively.

Stepwise extraction of Fe, Si from copper slag and self-assembly synthesis of microspheres for As(V) removal: Resource transformation and environmental governance

Heavy metal pollution control and industrial solid waste management have always been urgent environmental issues. The management of heavy metal pollution through industrial solid waste may be a solution to both problems. In this paper, copper slag (CS) is used as a base material to separate the iron and silicon with a relatively high percentage of content. The Fe-mSiO2/SA (FSA), a microsphere (Φ = 2–3 mm) adsorbent with specific adsorption capacity for As(Ⅴ), was finally synthesized by “Acid leaching & Alkaline extraction & Template synthesis & Gelatinization”. The optimal adsorption conditions were explored using response surface methodology. FSA has a wide range of pH applicability (3–9) and the maximum adsorption capacity is 140.45 mg/g by theoretical calculation. The adsorption process follows pseudo-second-order kinetic model, which indicates that the adsorption process is a surface homogeneous monolayer adsorption controlled by chemisorption mechanism. The synthesis mechanism of FSA was explored by systematic characterization of FSA, and the mechanism of As(Ⅴ) adsorption was elucidated. The −OH and FeOOH formed stable single-tooth or double-tooth complexes with As(Ⅴ) on the surface of FSA. Moreover, the unique spherical structure of FSA facilitates subsequent solid–liquid separation. This study is in line with the concept of economic applicability and “waste for waste”.