Hip Center Of Rotation Research Articles

Mid‐ to Long‐term Follow‐up of Severe Acetabular Bone Defect after Revision Total Hip Arthroplasty Using Impaction Bone Grafting and Metal Mesh

In revision total hip arthroplasty (THA), reconstruction of severe acetabular bone defect continues to be problematic for orthopedic surgeons. This study reports the mid- to long-term survivorship, radiological outcomes, and complications of impaction bone grafting (IBG) and metal mesh with a cemented acetabular component in the reconstruction of severe acetabular bone defects in revision THA. This retrospective consecutive study included 26 patients (29 hips: type II B, four; type II C, three; type III A, 10; and type III B, 12) who underwent revision THA, which was performed using IBG and metal mesh, between 2007 and 2014 in our institution. All patients were followed up regularly for clinical and radiographical assessments. Migration and loosening of prosthesis graft integration and complications were observed and analyzed. Survival analysis was performed using a Kaplan-Meier survival analysis. At the time of revision, 75.9% of the hips (22 hips) were classified as type III bone defects. The average follow-up period was 9.4 ± 2.8 (range, 2.4-14.0) years. Of the 29 hips, four hips (13.8%) were assessed as clinical failures; at the last follow-up, two had undergone re-revision THA, and two had not been scheduled for re-revision THA despite radiological failure of the acetabular component. Among them, three clinical failures (10.3%) were due to aseptic loosening, and one (3.4%) was due to infection. Radiographic evaluation showed bone graft integration in all hips during the follow-up. The Kaplan-Meier survivorship analysis revealed an acetabular reconstruction survival rate of 86.5% (95% confidence interval, 61.4%-95.7%) at 10 years. IBG and metal mesh with a cemented acetabular component for revision THA is an effective technique for treating severe acetabular bone defects, with effective mid- to long-term outcomes due to the solid reconstruction of the acetabular bone defect and restoration of the hip rotation center.

Acetabular Inclination as a Function of Hip Center of Rotation While Obtaining Inferior Screw Fixation: A Simulation Model

AbstractClinical success of cementless total hip arthroplasty is predicated on proper component position, restoration of biomechanics, and implantation of a mechanically stable construct. In the setting of acetabular bone loss, this target is more difficult to achieve, and elevation of the center of hip rotation may compromise the ability to obtain inferior screw fixation. We used the LifeMOD virtual human modeling simulation software (Smith & Nephew, San Clemente, CA) to determine the relationship between cup inclination and center of rotation position while maintaining the ability to obtain screw fixation within the superior pubic ramus. This simulation demonstrated that for every 5 mm of hip center elevation, cup inclination increased by 5.67 degrees. Based on this data, we recommend the use of a porous acetabular component when the hip center is elevated. This acetabular reconstruction allows for cementation of a liner to address the vertical nature of the cup needed to obtain inferior screw fixation within the superior pubic ramus.

Translated article] Trabecular titanium implants in complex acetabular revision surgery

IntroductionAcetabular revision surgery is a surgical challenge, especially when complex bone defects appear. This makes primary fixation and osseointegration of the implants difficult, which conditions the appearance of complications. Trabecular titanium implants attempt to solve these problems. ObjectivesTo evaluate our clinical-radiological results, the survival of the implants and the appearance of mid-term complications in acetabular revision surgery in a series of 37 acetabular replacements with Paprosky type IIIA and IIIB bone defects in which a trabecular titanium Cup-Cage revision implant was used. Material and methodWe conducted an observational, descriptive and retrospective study of 37 cases with complex acetabular defects (20 type IIIA and 17 type IIIB, five of them with pelvic discontinuity) in which the acetabular component was replaced by trabecular titanium cups between 2011 and 2019. We analysed clinical results (pain and functionality) and radiological parameters (restoration of the hip rotation centre and the mobilisation of the implants), as well as the appearance of complications. ResultsThe mean follow-up was 61 months. We obtained a median improvement of 8 points on the Merlé D’Aubigné-Postel functionality scale and 6 points on the VAS scale of pain perceived by the patient. We recorded two cases of acetabular loosening, one case of dislocation and three surgical wound infections without affecting the implant. ConclusionsThe use of trabecular titanium Cup-Cage implants could be a valid option in acetabular revision surgery with complex acetabular defects, presenting good clinical and radiological results and in terms of complications and survival of the implants, mainly due to their good primary fixation and subsequent osseointegration.

Risk factor investigation for hip dislocation after periacetabular tumour resection and endoprosthetic reconstruction via thin-slice CT-based 3D model

Dislocation of the hip remains a major complication after periacetabular tumour resection and endoprosthetic reconstruction. The position of the acetabular component is an important modifiable factor for surgeons in determining the risk of postoperative dislocation. We investigated the significance of horizontal, vertical, and sagittal displacement of the hip centre of rotation (COR) on postoperative dislocation using a CT-based 3D model, as well as other potential risk factors for dislocation. A total of 122 patients who underwent reconstruction following resection of periacetabular tumour between January 2011 and January 2020 were studied. The risk factors for dislocation were investigated with univariate and multivariate logistic regression analysis on patient-specific, resection-specific, and reconstruction-specific variables. The dislocation rate was 13.9% (n = 17). The hip COR was found to be significantly shifted anteriorly and inferiorly in most patients in the dislocation group compared with the non-dislocation group. Three independent risk factors were found to be related to dislocation: resection of gluteus medius (odds ratio (OR) 3.68 (95% confidence interval (CI) 1.24 to 19.70); p = 0.039), vertical shift of COR > 18 mm (OR 24.8 (95% CI 6.23 to 128.00); p = 0.001), and sagittal shift of COR > 20 mm (OR 6.22 (95% CI 1.33 to 32.2); p = 0.026). Among the 17 patients who dislocated, 70.3% (n = 12) were anterior dislocations. Three independent risk factors were identified, suggesting the importance of proper restoration of the COR and the role of the gluteus medius in maintaining hip joint stability.Cite this article: Bone Joint J2022;104-B(10):1180-1188.

Implantes de titanio trabecular en cirugía de revisión acetabular compleja

IntroductionAcetabular revision surgery is a surgical challenge, especially when complex bone defects appear. This makes primary fixation and osseointegration of the implants difficult, which conditions the appearance of complications. Trabecular titanium implants attempt to solve these problems. ObjectivesTo evaluate our clinical-radiological results, the survival of the implants and the appearance of mid-term complications in acetabular revision surgery in a series of 37 acetabular replacements with Paprosky type IIIA and IIIB bone defects in which a trabecular titanium Cup-Cage revision implant was used. Material and methodWe conducted an observational, descriptive and retrospective study of 37 cases with complex acetabular defects (20 type IIIA and 17 type IIIB, five of them with pelvic discontinuity) in which the acetabular component was replaced by trabecular titanium cups between 2011 and 2019. We analyzed clinical results (pain and functionality) and radiological parameters (restoration of the hip rotation centre and the mobilization of the implants), as well as the appearance of complications. ResultsThe mean follow-up was 61 months. We obtained a median improvement of 8 points on the Merlé D’Aubigné-Postel functionality scale and 6 points on the VAS scale of pain perceived by the patient. We recorded two cases of acetabular loosening, one case of dislocation and three surgical wound infections without affecting the implant. ConclusionsThe use of trabecular titanium Cup-Cage implants could be a valid option in acetabular revision surgery with complex acetabular defects, presenting good clinical and radiological results and in terms of complications and survival of the implants, mainly due to their good primary fixation and subsequent osseointegration.

The optimal screw-hole positions of the eccentric revision cup based on a morphological study

BackgroundBridging bone defects in revision total hip arthroplasty is a challenge to orthopedic surgeons. The eccentric revision cup is a progression of jumbo cup. Our aim is to confirm the optimal screw-hole positions of the eccentric revision cup by morphological measurements of three-dimensional pelvic reconstruction.MethodsEighty CT images were converted to virtual three-dimensional bones. After simulating the surgery procedure, all available screw holes were inserted with the screws in virtual. By measuring the length of the screw in the pelvic bone, we determined the rich bone stock area. Then the screw holes were designed according to the characteristics of bone stock distribution. The peripheral screw-hole cluster and inner screw-hole cluster were studied respectively.ResultsFor peripheral screw-hole cluster, five screw holes were evenly distributed between point A and point B in the thicker rim. For inner screw-hole cluster, screw hole 1 and screw hole 2 are the recommended inner screw holes.ConclusionThe eccentric revision cup has inherited the strengths of jumbo cup besides several unique advantages, including using the peripheral screws enhancing primary stability; decreasing the shift of hip rotation center and restoring biomechanical function; reducing the risk of dislocation because of the smaller head-cup differences; increasing the contact area between the outer cup and the host bone while maintaining a normal inclination of the inner cup. In this study, we confirmed the optimal screw-hole positions of the eccentric revision cup by surgical simulation and morphological measurement. However, biomechanical tests are still being further explored.

The application of custom-made 3D-printed titanium augments designed through surgical simulation for severe bone defects in complex revision total hip arthroplasty

BackgroundWith the development of radiology and three-dimensional (3D) printing technology, custom-made 3D-printed titanium augments have been more widely used. However, the radiological and clinical outcomes of custom-made augments lack reports. To better understand the clinical effect of using 3D-printed titanium augments and the significance of accurate placement, the aim of this study was to assess the outcomes when using custom-made 3D-printed titanium augments and to validate the idea that surgical simulation should be done before designing custom-made augments.MethodsA retrospective review was conducted on 31 surgical simulations and revision total hip arthroplasties using custom-made 3D-printed titanium augments. The safe zone, cup position, and hip rotation center were measured on anteroposterior radiographs. Clinical outcomes were assessed with a mean 21.1 months of follow-up.ResultsAll patients were positioned within the safe zone, and none of the acetabular cups nor the custom-made augments had any evidence of migration at the latest follow-up. A strong correlation was found between the planned cup position and the postoperative position. The average vertical position of the center of rotation was significantly increased from 3.55 cm to 2.35 cm. The mean Harris Hip Score was increased from 40.81 preoperatively to 65.46 postoperatively. Complications included gait abnormality, groin pain, fracture of the greater trochanter, and partial palsy of the sciatic nerve. However, patient satisfaction reached 92.3%.ConclusionSurgical simulations help to design custom-made augments accurately and improve surgical plans. Acetabular components supported with custom-made 3D-printed augments is a useful method to bridge severe bone deficiencies. In this study, both the radiologic results and clinical outcomes were favorable.Level of evidenceLevel 4.

Application of personalized digital analog assisted acetabular prosthesis precise implantation in Crowe typeⅠand Ⅱ hip dysplasia

To explore the effect of personalized digital analog assisted acetabular prosthesis precise implantation in hip dysplasia. From February 2017 to July 2019, 11 patients(12 hips) with hip dysplasia underwent total hip arthroplasty, including 4 males(5 hips) and 7 females(7 hips), aged from 27 to 61 years old, with an average of (46.64±12.93) years old;Crowe classification:8 hips in typeⅠ and 4 hips in typeⅡ. The preoperative thin-layer CT scan was imported into Mimics 10.01 software. The appropriate size and placement angle of acetabular prosthesis were selected through preoperative simulation, and the acetabular bone defect was understood to determine whether structural bone grafting was needed during the operation. The length of both lower limbs, the anteversion angle of acetabular prosthesis, the abduction angle, the height of acetabular rotation center and the horizontal distance of hip joint center before and after the operation were measured, and the postoperative dislocation, bone graft healing and acetabular cup loosening were observed. The hip Harris score was used to evaluate the joint function. All patients were followed up for 18 to 30 months with an average of (23.45±3.70) months. There was no prosthesis dislocation, loosening and bone graft healing after operation. One case had numbness in the innervation area due to the traction of sciatic nerve during operation, and was treated with neurotrophic drugs and recovered one month after operation. The length difference of both lower limbs decreased from (31.73±5.98) mm before operation to (4.73±1.90) mm 3 months after operation (t=15.268, P<0.01). The anteversion angle of acetabular cup and acetabulum was (17.45±3.62)°and abduction angle was (40.10 ± 2.30)° after operation. In all cases, the abduction angle and anteversion angle were within the safe range of Lewinek. The height of hip rotation center was (20.64±2.58) mm and the horizontal inward displacement of hip was (33.46±3.61) mm. Harris score increased from (45.36±2.34) before operation to (91.27±2.37) 3 months after operation (P<0.05). Through preoperative personalized digital analog reconstruction of acetabulum in patients with hip dysplasia, we can better understand the acetabular defect, help to evaluate the size and placement angle of acetabular prosthesis and whether structural bone grafting is needed, and obtain satisfactory clinical curative effect.

Use of a new off-the-shelf 3D-printed trabecular titanium acetabular cup in Chinese patients undergoing hip revision surgery: Short- to mid-term clinical and radiological outcomes

BackgroundRevision total hip arthroplasty (THA) has been a challenge for surgeons. The purpose of this study was to explore the short-to mid-term clinical and radiological outcomes of Chinese patients who underwent revision THA using a new off-the-shelf three-dimensional (3D)-printed trabecular titanium (TT) acetabular cup by comparison with a conventional porous coated titanium acetabular cup, to provide a reference for the recommendation of this prostheses.MethodsA retrospective analysis of 57 patients (57 hips) who received revision THA was performed from January 2016 to June 2019. A total of 23 patients received 3D-printed cups (observation group) and 34 patients received non-3D-printed cups (control group). Clinical scores including Visual Analogue Scale (VAS), Harris Hip Score (HHS) and Short Form 36 (SF-36), upward movement of the hip center of rotation(HCOR)and limb-length discrepancy (LLD), stabilization and bone ingrowth of cups were compared between two groups. The multivariate linear regression was used to determine the factors potentially influencing the HHS score. Postoperative complications in the two groups were also recorded.ResultsAll 57 patients were routinely followed up. The average follow-up durations in the control and observation groups were 43.57 ± 13.68 (24–65) months and 41.82 ± 11.44 (24–64) months, respectively (p = 0.618). The postoperative clinical scores significantly improved in both groups compared to the preoperative scores (p < 0.001). The VAS score did not significantly differ between the groups at 3 (p = 0.946) or 12 (p = 0.681) months postoperatively, or at the last follow-up (p = 0.885). The HHS score did not significantly differ between the groups at 3 months (p = 0.378) postoperatively but differed at 12 months (p < 0.001) postoperatively and the last follow-up (p < 0.001). The SF-36 score did not significantly differ between the groups at 3 months (p = 0.289) postoperatively, but was significantly different at 12 months (p < 0.001) postoperatively and the last follow-up (p < 0.001). Compared with the control group, the postoperative recovery of HCOR and LLD was better in the observation group. All cups remained stable, with no loosening throughout the follow-up period. But the observation group had a significantly better rate of bone ingrowth compared to the control group (p = 0.037). Multivariate linear regression analysis showed that different cup types, upward movement of the HCOR, and LLD influenced the HHS score at the last follow-up (p < 0.001, p = 0.005, respectively). None of the patients exhibited severe postoperative complications.ConclusionThe new off-the-shelf 3D-printed TT acetabular cup demonstrated encouraging short-to mid-term clinical outcomes in Chinese patients. It can effectively relieve pain, improve hip function, provide satisfactory biological fixation and high survival rate. But further follow up is necessary to assess its long-term outcomes.

Early outcomes of using custom-made augments in revision total hip arthroplasty.

The continuing high demand for revision total hip arthroplasty (RTHA) requires not only additional economic costs, but also the search for new, effective methods to manage the reconstruction of acetabular bone loss. This study focuses on the assessment of the clinical and radiographic outcomes after RTHA using custom-made augments (CMA) in the short-term follow-up period. We retrospectively analyzed the results of using CMAs in 19 patients (20 hips). The average follow-up period was 41.3months. All surgery was performed on defect types III and IV as per the Gross and Saleh classification. There was a statistically significant difference when comparing the Oxford Hip Score before RTHA of 15.0 (Std. deviation-5.9) and after RTHA of 36.3 (Std. deviation-6.3) (p = 0.01). All implants were radiologically stable. CMA has demonstrated a good ability to restore position of hip centre of rotation (HCOR). In the postoperative period, two patients (2 hips) had dislocations. Only one of two patients underwent re-revision due to dislocation. Treatment of uncontained loss of bone stock in RTHA using CMA shows promising clinical and radiographic results at short-term follow-up period; however, dislocation rate is 10% in this study.

Use of Customized 3D-Printed Titanium Augment With Tantalum Trabecular Cup for Large Acetabular Bone Defects in Revision Total Hip Arthroplasty: A Midterm Follow-Up Study.

Aims: In revision total hip arthroplasty (THA), large acetabular bone defects pose challenges for surgeons. Recently, wide application of trabecular tantalum, which has outstanding biocompatibility and mechanical properties, and the development of three-dimensional (3D) printing have led to the introduction of new schemes for acetabular reconstruction. However, few studies have focused on the treatment of bone defects with customized 3D-printed titanium augments combined with tantalum trabecular cup. Thus, we aimed to evaluate the effect of this therapy in patients who underwent revision THAs. Patients and Methods: We included 23 patients with Paprosky type III acetabular bone defects who underwent revision THA between January 2013 and June 2019. The preoperative hip rotation center and functional score were compared with those at 2–7 years (average 4.7 years) postoperatively to evaluate the midterm prognosis of our treatment choice. Results: Postoperatively, the rotation centres of all hips were comparable with those of the contralateral hips. Hip function improved with average Harris Hip Score improved from 33.5 (22.7–40.2) to 86.1 (73.5–95.6) and average Oxford Hip Score improved from 8.3 (0–14) to 38.8 (35–48) during follow-up. One dislocation, which occurred due to extreme hip flexion within 6 weeks, was treated with closed reduction, and no recurrent dislocation occurred. No nerve injury, infection, aseptic loosening, or osteolysis were observed and no re-revision was performed in any patient. Conclusion: Satisfactory midterm outcomes were obtained with 3D-printed titanium augment combined with tantalum cup for the treatment of acetabular defects in revision THA. Changes in the Harris Hip Score and Oxford Hip Score suggested a significant improvement in hip function.

Türk erişkinlerindeki kalça eklem morfolojisinde cinsiyet farklılıkları üzerine radyografik çalışma

Aim: This study aims to determine the gender differences in hip joint functional anthropometric measurement values in Turkish adults.Materials and Methods: Digital pelvis anterior-posterior radiographs of 300 randomly selected patients were analyzed. In these radiographs, reference lines were drawn and femoral neck-shaft angle (NSA), hip rotation center (HRC), abductor moment arm (AMA), body weight moment arm (BMA) were calculated. The relationship of the distribution of measurement results with gender and age was examined.Results: It was determined that the mean NSA scores in men were significantly higher than in women (p&amp;lt;0.05). It was determined that AMA value was significantly higher in men and BMA value was significantly higher in women (p&amp;lt;0.05). BMA/AMA ratio was found to be statistically significantly higher in women (p&amp;lt;0.005).Conclusion: Statistically significant differences were found between men and women in the mean of AMA, BMA and BMA/AMA in the Turkish population.

Three-dimensional-printed titanium implants for severe acetabular bone defects in revision hip arthroplasty: short- and mid-term results.

Severe acetabular bone defect is challenging in revision hip arthroplasty. In the present study, we aimed to present new treatment options with the 3D printing technique and analyze the clinical and radiographic outcomes of 3D-printed titanium implants for the treatment of severe acetabular bone defects in revision hip arthroplasty. A total of 35 patients with Paprosky type 3 bone defect and pelvic discontinuity (PD), who underwent hip revisions using 3D-printed titanium implants between 2016 and 2019 at our institution, were retrospectively reviewed. Patient-specific 3D-printed titanium augments and shells (strategy A) were used in 22 type 3A and two type 3B patients. Custom 3D-printed flanged components (strategy B) were used in 11 type 3B patients, including five PD. The clinical outcomes were evaluated with the Harris hip score (HHS). In addition, radiographic results were analyzed by the hip centre of rotation (V-COR and H-COR), implant failure, and survivorship. The mean follow-up was 41.5 months (range, 16-62). The HHS was improved from 47.8 ± 8.2 pre-operatively to 78.1 ± 10.1 at oneyear follow-up and 86.4 ± 5.1 at the last follow-up (p < 0.01). Post-operative V-COR and H-COR of the operated side were 20.8 ± 2.0 mm and 30.2 ± 1.6 mm compared with 51.4 ± 4.1 mm and 33.9 ± 9.0 mm pre-operatively (p < 0.01). The complications included one dislocation and one partial palsy of the sciatic nerve. At the latest follow-up, no radiological component loosening or screw breakage was present. 3D-printed titanium implants showed satisfactory short- and mid-term clinical and radiographic outcomes. It was an effective therapeutic regimen with a low rate of complications, providing a patient-specific and reliable strategy for the severe acetabular bone defect in revision hip arthroplasty.

Acetabular Revision Arthroplasty Based on 3-Dimensional Reconstruction Technology Using Jumbo Cups.

Background: This study was aimed at evaluating the changes in cup coverage (CC) and hip center of rotation (HCOR) in acetabular defects of various severities treated with acetabular revision using jumbo cups. Methods: A total of 86 hips were included. The American Academy of Orthopedic Surgeons (AAOS) classification of these patients was as follows: 16 patients, AAOS I; 16 patients, AAOS II; and 16 patients, AAOS III. A three-dimensional (3D) implant simulation technique was used to visualize the placement of jumbo cups during revision arthroplasty. The acetabular anteversion, inclination, CC, and the HCOR were measured. Results: The inclination and anteversion of simulated acetabular cups in AAOS I–III groups were consistent with the normal acetabular anatomy. Compared with the controls, in AAOS I–III groups, the HCOR was significantly increased and CC was significantly decreased. The HCOR elevation was significantly higher in AAOS III patients than in AAOS I (p = 0.001) and AAOS II patients (p < 0.001). The use of the jumbo cup technology for acetabular revision would decrease the CC in AAOS I–III patients to 86.47, 84.78, and 74.51%, respectively. Conclusion: Our study demonstrated that in patients with acetabular defects, acetabular revision arthroplasty using jumbo cups will lead to decreased CC and HCOR upshift. Upon classifying these patients according to the AAOS classification, CC decreased with the severity of acetabular defects, and the elevation of the HCOR in AAOS III patients exceeded 10 mm and was significantly higher than in other patients.

Reconstruction of Paprosky Type III Acetabular Defects by Three-Dimensional Printed Porous Augment: Techniques and Clinical Outcomes of 18 Consecutive Cases.

ObjectiveTo introduce the surgical technique of reconstruction of Paprosky type III acetabular defects by 3D printed porous augments.MethodsFirst, CT scans of pelvis were obtained to establish the 3D reconstruction model of 3D printed porous augment. Then, a nylon pelvis model was printed to simulate operation with the surgeons. At this time, the augment was designed and modified according to the surgeon's suggestions and the 3D printing principles. Eighteen patients with Paprosky type III acetabular defects receiving reconstructive surgery by 3D printed porous augments were included in current study. Their data, including general information, intra‐operative findings, imaging results, functional scores, and complications were retrospectively analyzed.ResultsThe mean follow‐up time lasted 33.3 ± 2.0 (24–56) months. The average limb‐length discrepancy (LLD) was 31.7 ± 4.2 (3–59) mm preoperatively, 7.7 ± 1.4 (1–21) mm postoperatively (P < 0.0001), and 7.5 ± 1.2 (0–18) mm at the latest follow‐up. The mean vertical position of hip center of rotation (HCOR) from the interteardrop line changed from preoperative 50.7 ± 3.9 (23.3–75.3) mm to postoperative 22.9 ± 1.9 (10.1–40.3) mm (P < 0.0001), with the latest follow‐up revealing an HCOR of 22.3 ± 1.7 (11.0–40.5) mm. Follow‐up study showed that no hip had radiolucencies and radiological loosening of the acetabular components and augment. The average Harris hip score (HHS) improved from 40.3 ± 4.5 (10.5–71) before operation to 88.4 ± 1.9 (75–97) at the last follow‐up (P < 0.0001). Moreover, follow‐up exhibited that no periprosthetic joint infection, hip dislocation, fracture, and re‐revision occurred.ConclusionSurgical treatment of Paprosky type III acetabular defect with 3D printed porous augment was simple, achieved good match between porous augment and the defect bone surface and the acetabular component, ideally restored LLD and HCOR after operation, significantly improved HHS and attained good early clinical outcomes. It is a promising personalized solution for patients with severe acetabular bone defect.

Implant positioning in total hip arthroplasty: influence of horizontal and vertical offset on functionality of prosthetic hip joint.

To analyze the effect of implant position measured in terms of offset on patient reported outcomes (PRO) following hip arthroplasty (THA). A total of 243 patients of the total hip replacement who had a one year follow-up were included in the study. Standard both hips radiograph was used to asses post-surgery implant position in terms of horizontal offset and vertical offset, and correlated with functional outcome which was evaluated as change in PRO. i.e., Harris hip score (HHS) post-op. With center of hip rotation as reference, horizontal offset was calculated as sum of distance, of centre, from proximal femoral shaft axis and a vertical line through ipsilateral teardrop, and vertical offset as limb length discrepancy. Post-op patients were classified into three groups depending on the measurement of horizontal offset of the operated hip. The patients having operated hip horizontal offset within 5mm of the normal hip were grouped as restored offset (RO); those having shorter or higher offset by more than 5mm compared to normal hip were labeled as decreased (DO) or increased offset (IO) group respectively. The groups were further subdivided into suboptimal and optimal function groups based on HHS, and among these groups, limb length discrepancy was evaluated. Post follow-up mean HHS (78.23 ± 9.96) improved significantly in all three groups (p < 0.0001). The difference in post-operative HHS among DO, RO, and IO groups was significant, with their averages being 72.5 ± 4.7, 82.1 ± 6.5, and 75.2 ± 4.8 respectively (p = .01). Limb length discrepancy was significantly more common in patients with suboptimal functional scores in all three groups. This study concluded that both horizontal offset and vertical offset should be reconstructed in patients operated with unilateral THR due to hip pathology, since both factor demonstrated a comparable additive effect on clinical outcome.

Compensation of acetabular defects in hip arthroplasty

Acetabular reconstruction is a necessary condition for improving the survival rate and proper functioning of the implant. The issue of compensation for bone loss remains one of the most difficult and controversial in orthopaedics. The article aimed to analyze approaches to the problem of management of acetabular defects in hip replacement. The paper presents the key features of the anatomy and radiological anatomy of the acetabulum. Modern modifications of acetabular components of an endoprosthesis, their advantages and disadvantages, as well as ways to compensate for acetabular bone loss with bone substitute materials are considered. The review highlights the use of 3Dprinting technologies, the interaction between physicians and other experts in this field. Currently, an active search for materials, alternatives to autogenous bone, as well as ways to facilitate the design and reduce the negative impact of the implant on the patient's bone tissue continues. The use of additive technologies seems to be the most promising direction that allows applying an individual approach to each clinical case, but it is available only in specialized centres and is associated with significant material, technical and legal difficulties. Stable fixation of the acetabular component, according to the literature, is achieved under the condition of restoration of hip rotation centre in the native acetabulum area, restoration of normal anatomical relations in the hip joint and adequate replacement of bone loss.

3D reconstruction protocol in complex acetabular defects

The current paper describes the protocol used in our clinic for 3D imaging, reconstruction and printing of complex acetabular defects that are used for surgical planning of complex acetabular defects. Surgical guides have also been developed to aid optimal acetabular reamer placement in order to recreate the optimal hip rotation centre for each patient undergoing revision hip arthroplasty that has impaired acetabular bone stock

Application of porous tantalum Jumbo cup in revision of hip arthroplasty

To investigate the clinical effect of porous tantalum Jumbo cup on acetabular reconstruction in revision of total hip arthroplasty. From September 2014 to December 2017, 18 patients(18 hips) with acetabular defect were reconstructed by porous tantalum Jumbo cup technology, including 6 males and 12 females;the age ranged from 54 to 76 years old with an average of(63.8±15.3) years. There were 6 cases of paprosky typeⅡA, 8 cases of typeⅡB, 2 cases of typeⅡC and 2 cases of type Ⅲ a. Harris score and visual analogue scale (VAS) were performed before and after operation. Imaging examination was performed to evaluate the position of hip rotation center and prosthesis, and to judge whether acetabular loosening, displacement and complications existed. All cases were followed up for 13 to 49 months, with an average of 20.6 months. Harris score increased from 54.6±4.7 to 86.5±3.2 one year after operation(P<0.01), and VAS score decreased from 6.8±0.7 to 0.8±0.6 one year after operation (P<0.01). The transverse coordinate of hip rotation center was (3.52±0.72) cm before operation and (3.47±0.54) cm after operation (P>0.05). The longitudinal coordinate of hip rotation center was improved from (3.02±0.84) cm before operation to (2.35±0.53) cm after operation (P<0.01). During the follow-up period, the Jumbo cup was well fixed without loosening and displacement, the acetabular cup had bone ingrowth in varying degrees, and no light transmission line and osteolysis around the acetabular cup were found. No complications such as infection and nerve injury occurred. The method of reconstructing acetabular bone defect with porous tantalum Jumbo cup is simple and easy, the early stability of acetabulum is good, and the short-term follow-up effect is good.

Comparison of hip offset and rotation center reconstruction between robot-assisted and manual total hip arthroplasty

Objective: To compare the differences of hip offset and rotation center reconstruction between robot-assisted and manual total hip arthroplasty (THA). Methods: Patients underwent robot-assisted and manual THA from May to September of 2020 in the First Affiliated Hospital of Chongqing Medical University were enrolled in this study. The patients included 27 patients (28 hips) in robot-assisted THA (rTHA) group and 29 patients (31 hips) in manual THA (mTHA) group. In rTHA group, there were 16 males and 11 females, with a mean age of (59±13) years. In mTHA group, there were 18 males and 11 females, with a mean age of (63±14) years. Basic information, including gender, age, body mass index (BMI), diagnosis and functional scoring etc, were recorded. In rTHA group, Mako robot system was used for preoperative planning, intraoperative real-time location and navigation. In mTHA group, traditional preoperative template design and surgical procedure were carried out. Operation time and functional scoring were compared postoperatively. Femoral offset, acetabular offset, global offset, rotation center changes in vertical and horizontal directions were measured on pelvis X-ray and analyzed. The correlation between intraoperative feedback of global offset change in robot system and postoperative measured global offset were analyzed. Results: Operation time in rTHA group was (80±10) min, which was statistically longer than that in mTHA group ((58±18) min, P<0.001). With 6 months' follow-up, the Harris scoring in rTHA group was 94.9±2.8, which was statistically higher than that in mTHA group (93.1±2.8, P=0.017), however there was no statistic difference in WOMAC scoring between rTHA and mTHA group (7.0±3.8 vs 7.1±2.4, P=0.840). Absolute global offset change within 5 mm, 5-10 mm and lager than 10 mm were 71.4%(20/28), 28.6%(8/28) and 0 in rTHA group, which were 45.2%(14/31), 29.0%(9/31) and 25.8%(8/31) in mTHA group (all P<0.05). A positive relation was found between intraoperative feedback of global offset change in robot system and postoperative measured global offset in rTHA group (r=0.77, P<0.001). It was found that rotation center changes concentrated in outer upper quadrant in both groups, and rotation center change in rTHA group concentrated mainly in the area less than 10 mm, however, rotation center change in mTHA group was more dispersive compared with rTHA group. Conclusion: rTHA may accurately reconstruct hip offset and rotation center, intraoperation feedback of global offset change may be an effective reference.