High Load Research Articles

Synergistic Regulation of Anode and Cathode Interphases via an Alum Electrolyte Additive for High‐Performance Aqueous Zinc‐Vanadium Batteries

AbstractA zinc (Zn) metal anode paired with a vanadium oxide (VOx) cathode is a promising system for aqueous Zn–ion batteries (AZIBs); however, side reactions proliferating on the Zn anode surface and the infinite dissolution of the VOx cathode destabilise the battery system. Here, we introduce a multi‐functional additive into the ZnSO4 (ZS) electrolyte, KAl(SO4)2 (KASO), to synchronise the in situ construction of the protective layer on the surface of the Zn anode and the VOx cathode. Theoretical calculations and synchrotron radiation have verified that the high‐valence Al3+ plays dual roles of competing with Zn2+ for solvation and forming a Zn−Al alloy layer with a homogeneous electric field on the anode surface to mitigate the side reactions and dendrite generation. The Al‐containing cathode–electrolyte interface (CEI) considerably alleviates the irreversible dissolution of the VOx cathode and the accumulation of byproducts. Consequently, the Zn||Zn cell with KASO exhibits an ultra‐long cycle of 6000 h at 2 mA cm−2. Importantly, the VOx cathodes (VO2, V2O5 and NH4V4O10) in the ZS−KASO electrolyte showed excellent cycling stability, including Zn powder||VO2 cells and Zn||VO2 pouch cells. Even better, the full cell exhibits excellent cycling stability at low negative/positive (N/P) ratio of 2.83 and high mass loading (~16 mg cm−2). This study offers a straightforward and practical reference for concurrently addressing challenges at the anode and cathode of AZIBs.

High‐Entropy Electrolyte Driven by Multi‐Solvation Structures for Long‐Lifespan Aqueous Zinc Metal Pouch Cells

Aqueous zinc metal batteries (AZMBs) are promising for grid‐scale energy storage due to their low cost and high safety. However, poor stability and an unfavorable freezing point hinder their actual application. Herein, a ternary salts‐based high‐entropy electrolyte (HEE) composed of Zn0.2Na0.4Li0.4(ClO4)1.2·7H2O is proposed to address the above issues. The addition of perchlorate salts with different cations reduces the size of ion clusters, significantly increases the solvation structure species, and promotes the anion‐rich Zn2+ solvation structures, resulting in an enlarged electrochemical stability window, favorable viscosity and ionic conductivity, and low freezing point. Furthermore, characterization and calculations confirm that multiple types of solvation structures effectively increase the electrolyte entropy. As a consequence, the Zn/Zn symmetric cells in HEE can sustainably cycle for at least 1000 hours and 1500 hours under room and subzero temperatures, respectively. The Na0.33V2O5/Zn and polyaniline/Zn full cells can even last for 30000 and 20000 cycles without capacity decay at −20 °C, respectively. The pouch cells employing HEE deliver promising capacity and stability, even at high mass loading of active materials. This strategy of introducing multiple salts with different cations to construct a high‐entropy environment provides a facile approach for high‐performance and long‐lifespan AZMBs across a wide temperature range.

Psychometric Testing of the Cross-Culturally Adapted Thai Version of the Caregiver Self-Efficacy in Contributing to Patient Self-Care Scale in Caregivers of Patients With Chronic Illnesses.

To evaluate the psychometric properties of the Caregiver Self-Efficacy in Contributing to Patient Self-Care Scale (CSE-CSC). The CSE-CSC scale was developed congruently with the Caregiver Contribution to Self-Care of Patient with Chronic Illness Inventory (CC-SC-CII) to assess caregiver self-efficacy (CSE), the motivation factor of caregiving. Its applicability in Asian populations, including Thailand, was limited. Psychometric tests were guided by COnsensus-based Standards for the selection of health Measurement INstruments (COSMIN) principles. This included translating the English version into Thai, following the principles of good practice for the translation and cultural adaptation process for patient-reported outcome (PRO) measures. Nine nursing experts evaluated the content validity. The analysis included caregivers of patients with chronic conditions from 16 primary care centres in Thailand. We tested the structural validity using exploratory factor analysis (EFA), confirmatory factor analysis (CFA) and concurrent validity for CC-SC-CII-v2. We tested the scale's reliability with methods for multidimensional and unidimensional constructs, the intraclass correlation coefficients (ICCs) and measurement error variance. Kappa coefficient (k = 1.00) indicated the scale's excellent content validity. The final analysis included a total of 407 samples. The EFA with the first split-half subsample (n = 194) extracted a two-dimensional structure. One reflected CSE in Maintenance and Monitoring behaviour and another captured CSE in Management behaviour. CFA with the second split-half subsample (n = 213) and the overall sample (n = 407) supported the scale's bidimensional model with high factor loadings. Each dimension and the overall CSE-CSC scale positively correlated with each scale and the overall CC-SC-CII-v2. McDonald's ω and Cronbach's α (both ranged from 0.91-0.94) indicated excellent internal reliability. Test-retest reliability showed ICCs between 0.95 and 0.96. Measurement error yielded satisfactory results. Testing of the Thai CSE-CSC scale supported validity and reliability, indicating that the scale can apply to Thai caregivers. This scale can be used in clinical practice and research to evaluate CSE in contribution to patient self-care.

High-Entropy Electrolyte Driven by Multi-Solvation Structures for Long-Lifespan Aqueous Zinc Metal Pouch Cells.

Aqueous zinc metal batteries (AZMBs) are promising for grid-scale energy storage due to their low cost and high safety. However, poor stability and an unfavorable freezing point hinder their actual application. Herein, a ternary salts-based high-entropy electrolyte (HEE) composed of Zn0.2Na0.4Li0.4(ClO4)1.2·7H2O is proposed to address the above issues. The addition of perchlorate salts with different cations reduces the size of ion clusters, significantly increases the solvation structure species, and promotes the anion-rich Zn2+ solvation structures, resulting in an enlarged electrochemical stability window, favorable viscosity and ionic conductivity, and low freezing point. Furthermore, characterization and calculations confirm that multiple types of solvation structures effectively increase the electrolyte entropy. As a consequence, the Zn/Zn symmetric cells in HEE can sustainably cycle for at least 1000 hours and 1500 hours under room and subzero temperatures, respectively. The Na0.33V2O5/Zn and polyaniline/Zn full cells can even last for 30000 and 20000 cycles without capacity decay at -20 °C, respectively. The pouch cells employing HEE deliver promising capacity and stability, even at high mass loading of active materials. This strategy of introducing multiple salts with different cations to construct a high-entropy environment provides a facile approach for high-performance and long-lifespan AZMBs across a wide temperature range.

Academic stress in dental students: suggestions for care in university institutions

Stress is a challenging situation that is generated by the arrival of an unexpected or novel situation that is difficult to solve. Dental students are subjected to high stress loads. The purpose of this paper is to briefly review the most recent literature on this topic and to make suggestions on how to approach it according to this and the authors' experience.

Scalable Atomic-Layer Tailoring of Abundant Oxide Supports Unlocks Superior Interfaces for Low-Metal-Loading Dehydrogenation.

Liquid organic hydrogen carriers (LOHCs) offer a promising solution for global hydrogen infrastructure, but their practical application faces two key challenges: sluggish dehydrogenation processes and the reliance on catalysts with high noble metal loadings. This study presents a scalable approach to reduce noble metal usage while maintaining high catalytic activity. We synthesized an ultralow Pt content (0.1 wt%) catalyst using γ-Al2O3-based pellet support with atomic layer deposition (ALD) of TiO2. Advanced characterization techniques reveal that the thin ALD-TiO2 shell provides a heterogeneous interface, confining electronically rich Pt-nanoparticle ensembles. The catalyst outperforms both equivalent Pt-content catalysts and a commercial 0.5 wt% Pt/γ-Al2O3 catalyst in homocyclic LOHC dehydrogenation. This study provides insights into the beneficial role of ALD-engineered interfaces for catalytic supports and offers an efficient approach for scalable production of low-noble-metal-content catalysts, with implications for various catalytic processes.

A hybrid system based on the combination of adsorption, electrocoagulation, and wetland treatment for the effective remediation of industrial wastewater from underground coal gasification (UCG)

The study verified the effectiveness of treating post-process underground coal gasification (UCG) wastewater, containing high loads of inorganic and organic pollutants, using constructed wetlands (CW) enhanced by hybrid adsorption and electrocoagulation (EC) techniques. Four different system configurations were tested: wetland, EC/wetland, adsorbent/wetland, and EC/adsorbent/wetland. Each experiment lasted 60 days. The feed and effluents from each treatment step were analysed for their basic physicochemical parameters such as metals and trace elements, phenols, sulphides, cyanides, total organic carbon (TOC), chemical oxygen demand (COD), biological oxygen demand (BOD), benzene, toluene, ethylene, xylene (BTEX), and polyaromatic hydrocarbons (PAHs).Systems with electrocoagulation proved to be effective in the case of metal removal. The best results were obtained for Fe, Ni, Sb and As (up to 96%, 98%, 94% and 82% respectively). The systems were ineffective in removing Mn. All tested systems showed the greatest effectiveness in the treatment of wastewater from phenols, BTEX and CN (almost 100% removal). CWs without preliminary electrocoagulation showed practically 100% effectiveness in removing BTEX after 14 days of treatment. Electrocoagulation was particularly effective in reduction of large quantity of PAH compounds (from 1228 μg/l to below 0.050 μg/l). Effective toxicity reduction from V class to II class after 60 days in comparison with meeting the requirements contained in the Best Available Techniques (BAT) document, showed that all tested systems were favorable in terms of UCG wastewater treatment. A significant decrease in toxicity was observed in just 14 days (around 90% reduction of toxicity measured in TU values for systems without adsorbent and around 75% for systems with adsorbent). The wastewater were still toxic due to the formation of degradation intermediates of organic compounds (BTEX, PAHs, phenol compounds), despite a significant decrease in the concentration of contaminants, therefore toxicity assessment should be one of the evaluation criteria for industrial wastewater treatment.

Soil arthropod diversity, richness, and abundance in agroecological and conventional cotton production systems in Chaco, Argentina

In Argentina, agroecology has grown in last years as a scientific paradigm that seeks to design and evaluate agroecosystems considering sustainability, complexity, and uncertainty. Diversity is a key factor in the design and management of production systems and a necessary component for conservation biological control and the reduction of agrochemicals use. Cotton (Gossypium hirsutum) crop in northern Argentina is usually managed with high load of agrochemicals: agroecological production arises as an alternative. This study evaluated the diversity, richness, and abundance of soil arthropods using pitfall traps in two experimental cotton plots under conventional (CONV) and agroecological management (AE) in Chaco, Argentina. AE system presented higher diversity and richness of predators compared with CONV, even when natural preparations were used for pest control. The phytophagous arthropods showed higher diversity and richness in CONV, even when pyrethroid insecticides were applied for pest control and preventively. The abundance in AE was lower for predators and higher for phytophagous arthropods. Agroecological production of cotton can be a tool that favors conservative biological control and an alternative for areas where protecting the health of farmers and the ecosystem is a priority.

Encapsulation of Rifampicin in Solid Lipid Nanoparticles by Microwave‐Assisted Microemulsion Method

AbstractRifampicin (RF) is a potent antibiotic, but its clinical effectiveness is limited by poor water solubility and stability. To overcome these limitations, RF is encapsulated in solid‐lipid nanoparticles (SLNs) using a one‐pot microwave microemulsion method. This study aimed to synthesize and characterize RF‐loaded SLNs, evaluating their physicochemical characteristics and antimicrobial efficacy. The synthesized SLNs exhibit particle sizes ranging from 150 to 200 nm, with a high encapsulation efficiency of ≈55% and high loading capacity. The particles are imaged by cryogenic‐transmission electron microscopy and found to be circular and elongated, with RF homogenously distributed throughout the particles. The RF‐loaded SLNs demonstrate potent antimicrobial activity, as evidenced by disc diffusion assays. The SLNs exhibits a sustained drug release profile, highlighting their potential as an effective drug delivery system for antimicrobial treatment. These findings suggest that SLNs can enhance the stability, bioavailability, and therapeutic efficacy of hydrophobic drugs like RF.

Challenges of Congenital HHV6 Infection Diagnosis and Treatment: Two Case Reports and Literature Review

Introduction: Congenital human herpesvirus 6 (HHV6) infection occurs in 1% of the general population and may result from the transmission of an inherited chromosomally integrated HHV6 (iciHHV6) or transplacental infection. It is mostly asymptomatic. Case reports: Case 1: a 29th-week-old female preterm newborn, admitted to the neonatal intensive care unit, became clinically unstable and irritable on the 20th day of hospitalization. Cranial ultrasound, revealed a significant posthemorrhagic tetraventricular dilation, with signs of ventriculitis. Investigations revealed HHV6 positivity on cerebrospinal fluid polymerase chain reaction multiplex panel testing and HHV6-DNA high viral loads in plasma samples. Case 2: a female late preterm newborn was admitted to the neonatal intensive care unit due to early-onset sepsis. Investigations revealed group B streptococcus positive blood cultures and cerebrospinal fluid HHV6 positivity on polymerase chain reaction multiplex panel testing, with negative bacterial culture. After 3 days of adequate antibiotic treatment, she maintained persistent moaning, which motivated a cranial ultrasound, revealing mild brain edema. Clinical improvement was observed only after beginning antiviral treatment in both newborns. Due to the persistency of high viral loads in both cases, despite antiviral treatment and clinical improvement, an iciHHV6 was suspected and posteriorly confirmed. Discussion/conclusion: Congenital iciHHV6 infection diagnosis is challenging because the presence of an iciHHV6 results in persistently high viral loads, even in the absence of active infection. Only a few diagnostic techniques can confirm active replication; unfortunately, these are not available in most countries. The decision to initiate antiviral treatment should be based on clinical judgment. Better ways for the diagnosis of active infection are needed.

Near-Surface Reconfiguration of Biopolymer Blends by Mechanical Embossment: Creation of Friction-Reduced Foils

Biopolymer blends of polylactic acid (PLA) and polybutylene adipate-co-terephthalate (PBAT) are extruded into flexible monolayer films. These blends are excellent candidates for the realization of environmentally friendly packaging applications. A necessary pre-requisite for that are appropriate tribological properties under mechanical contact. Reasonable wear resistance allows good protection of packed goods, and low friction forces reduce difficulties in stacking. In this research, mechanical embossment under high loads at room temperature was used for the modification of polymer surfaces to exhibit a significant friction reduction under dry conditions. The results particularly show a systematic decrease in the coefficient of friction for biopolymer blends containing 30 wt% and 40 wt% PBAT. FTIR was used to analyze the change in surface composition after mechanical embossing. A sophisticated FTIR calibration method revealed that the blend with 30 wt% PBAT shows a modified distribution of PBAT and PLA at the surface due to mechanical embossment. This leads to a controlled and long-lasting modification of the surface properties without a substantial change in the chemical composition of the polymer in bulk. Without the use of additional coatings, biodegradable packaging foils with improved characteristics are accessible.

A detailed comparison of ethanol–diesel direct fuel blending to conventional ethanol–diesel dual-fuel combustion

Dual-fuel combustion is a well-known measure to enable the combustion of low-reactivity fuels (LRF) in compression-ignited engines with high thermal efficiency through a pilot injection of a high-reactivity fuel (HRF). In most cases, the LRF is introduced into the intake manifold and therefore premixed with the air before entering the combustion chamber during the intake stroke (premixed charge operation, PCO). In this work, this approach is investigated for bioethanol-diesel dual-fuel combustion using external and internal exhaust gas recirculation (EGR) to improve emissions and engine efficiency. In addition, PCO is compared to an alternative concept in which bioethanol and diesel are blended shortly upstream of the high-pressure pump (premixed fuel operation, PFO) at variable mixing ratios. The results show that higher ethanol shares of up to 70% can be achieved at low engine load when using PCO, while at medium and high load, the maximum energy share of ethanol is higher with PFO. While PCO is limited by engine knock, PFO rather suffers from the reduction in cetane number. In PCO, external and internal EGR allow for a reduction of unburned hydrocarbons (up to − 82%) and carbon monoxide (up to -60%), while nitrous oxide emissions are simultaneously lowered by up to − 65%. Both with and without EGR, PFO shows low emissions of unburned hydrocarbons and carbon monoxide (similar to conventional diesel combustion) and a significant reduction in nitrous oxide and soot formation. Brake thermal efficiency (BTE) drops in both modes compared to conventional diesel combustion, in PCO operation due to unburned and partially unburned fuel and in PFO due to increased friction in the high-pressure fuel pump caused by an increased fuel flow.

Mycobacterium avium complex (MAC) infection in severely immunocompromised people living with HIV: Findings from a five-year cohort.

We sought to clarify the current incidence, risk factors and symptoms of disseminated Mycobacterium avium complex (dMAC) infection in admitted people living with HIV in a hospital in the Southeast of Spain. 5-years observational, retrospective and single-centre study. Demographic, clinical and analytical variables, along with microbiological, treatment and follow-up were collected. Five cases of dMAC infection in severely immunocompromised people living with HIV people living were found. dMAC was diagnosed in 22.7% of patients under 100 CD4. All patients presented with fever and clinical manifestations of pneumonia, lymphadenopathy, or gastrointestinal symptoms. Despite low CD4 levels and high viral loads in some cases, primary prophylaxis had not been previously administered. Until 2018, U.S. American guidelines recommended antimycobacterial prophylaxis for patients with low CD4 cell counts, a practice not adopted in Europe. Untreated dMAC infection is associated with high morbidity and mortality rates. dMAC infection represents a prevalent disease in severely immunosuppressed people living with HIV. dMAC requires a high index of suspicion in this population, in order to perform mycobacterial cultures from different samples.

Youth and Adolescent Athlete Musculoskeletal Health: Dietary and Nutritional Strategies to Optimise Injury Prevention and Support Recovery

Background: Despite the well-documented benefits of exercise and sports participation, young athletes are particularly vulnerable to musculoskeletal injuries. This is especially true during periods of rapid growth, sports specialisation, and high training loads. While injuries are an inevitable aspect of sports participation, the risk can be minimised by promoting the development of strong, resilient tissues through proper nutrition and injury prevention strategies. Moreover, targeted nutrition strategies can accelerate recovery and rehabilitation, allowing for a quicker return to sports participation. Methods: This narrative review synthesises scientific evidence with practical insights to offer comprehensive dietary recommendations aimed at strengthening tissues and supporting the healing process during recovery and rehabilitation. The selection of all sources cited and synthesised in this narrative review were agreed upon by contributing author consensus, experts in sports nutrition (R.A., H.V., B.D.) and exercise and sports medicine (M.H.). Results: Key topics include factors that contribute to injury susceptibility, general dietary recommendations for growth and development, sports nutrition guidelines, and nutrition considerations during injury and rehabilitation. This review also addresses external factors that may lead to suboptimal nutrition, such as food literacy and eating disorders. Conclusions: By highlighting these factors, this article aims to equip coaches, nutritionists, dietitians, athletic trainers, physical therapists, parents/guardians, sporting organisations, and schools with essential knowledge to implement effective nutritional strategies for injury prevention, recovery, and rehabilitation, ultimately enhancing long-term health and athletic performance.

Measurement of dynamic deformation during shock loading using a fiber-optic loop-sensor

Abstract Characterizing materials under shock loading has been of interest in fields such as protective material development, biomechanics to study the injury mechanics and high-speed aerodynamic structures. However, shock loading of material is a very short duration phenomenon and it is extremely challenging to develop sensors for dynamic measurements under such loading conditions. Optical fiber sensors that present the possibilities to allow high resolution measurement of force or displacement in such high strain rate loading conditions. This work studies the possibility of developing a single mode optical fiber sensor based on the principle of power losses from the curved section for dynamic measurements under shock loading conditions. The strain measurement results obtained from the optical sensors are validated with the controlled digital image correlation measurements are found to be in close correlation. The sensor was able to provide time sensitivity of better than 1 ms. The results show that the fiber sensor has the characteristics of high sensitivity and high precision, which can be used to measure fine vibration in real-time.

Bacterial contamination of autologous blood salvaged during deceased donor liver transplantation: a prospective observational study.

Decompensated cirrhotic patients experience severely increased intestinal permeability and bacterial translocation. Thus, autologous blood salvaged during deceased donor liver transplantation (DDLT) may be contaminated with enteric bacteria. We aimed to evaluate bacterial contamination of autologous blood salvaged during DDLT and its association with post-transplant bacteremia. In 30 patients undergoing DDLT, bacterial culture was performed in salvaged autologous blood samples: one before graft reperfusion (non-leukoreduced) and two after graft reperfusion (non-leukoreduced and leukoreduced). The primary outcome was bacterial contamination of salvaged autologous blood. Seven of 30 patients (23.3%) were positive for bacteria (3 enteric/4 non-enteric) before graft reperfusion while 11 patients (36.7%) were positive (5 enteric/6 non-enteric) after graft reperfusion. Six of 7 patients who were positive for bacteria before graft reperfusion were positive after graft reperfusion with the same bacteria. Only 4 of 11 contaminated blood samples were converted to negative after leukoreduction. Post-transplant bacteremia risk was insignificantly greater in patients who received autologous blood with bacteria than in patients without bacteria (30.0% vs. 5.0%, P = 0.06). We found contamination of salvaged autologous blood with enteric bacteria throughout DDLT and incomplete performance of leukoreduction, indicating high bacterial load. The potential association between contaminated autotransfusion and post-transplant bacteremia warrants further validation in a larger prospective study.Clinical trial notation: This study was registered at the Clinical Research Information Service (CRiS; https://cris.nih.go.kr ; No. KCT0007223; principal registration investigator: Sangbin Han, date of registration: April 25, 2022).

An Overview of the R&D of Flywheel Energy Storage Technologies in China

The literature written in Chinese mainly and in English with a small amount is reviewed to obtain the overall status of flywheel energy storage technologies in China. The theoretical exploration of flywheel energy storage (FES) started in the 1980s in China. The experimental FES system and its components, such as the flywheel, motor/generator, bearing, and power electronic devices, were researched around thirty years ago. About twenty organizations devote themselves to the R&D of FES technology, which is developing from theoretical and laboratory research to the stage of engineering demonstration and commercial application. After the research and accumulation in the past 30 years, the initial FES products were developed by some companies around 10 years ago. Today, the overall technical level of China’s flywheel energy storage is no longer lagging behind that of Western advanced countries that started FES R&D in the 1970s. The reported maximum tip speed of the new 2D woven fabric composite flywheel arrived at 900 m/s in the spin test. A steel alloy flywheel with an energy storage capacity of 125 kWh and a composite flywheel with an energy storage capacity of 10 kWh have been successfully developed. Permanent magnet (PM) motors with power of 250–1000 kW were designed, manufactured, and tested in many FES assemblies. The lower loss is carried out through innovative stator and rotor configuration, optimizing magnetic flux and winding arrangement for harmonic magnetic field suppression. Permanent magnetic bearings with high load ability up to 50–100 kN were developed both for a 1000 kW/16.7 kWh flywheel used for the drilling practice application in hybrid power of an oil well drilling rig and for 630 kW/125 kWh flywheels used in the 22 MW flywheel array applied to the flywheel and thermal power joint frequency modulation demonstration project. It is expected that the FES demonstration application power stations with a total cumulative capacity of 300 MW will be built in the next five years.

Water quality evaluation by WQI and ICOs for the rivers of Joya de los Sachas and Francisco de Orellana

A monitoring program enabled the evaluation of water quality and the simulation of the pollution dynamics of the rivers in the Joya de los Sachas and Francisco de Orellana cantons in Ecuador. For this assessment one used the WQI (water quality index) and the pollution indices ICOMO (organics contamination), ICOSUS (suspended solids), ICOMI (mineralization), ICOTRO (trophy system), and ICOpH (pH Index). The mathematical model operates with several input parameters, including dissolved oxygen, fecal coliforms, the biochemical oxygen demand (BOD5), turbidity, total solids, total phosphorus, pH, total nitrogen, suspended solids, alkalinity, conductivity, temperature, and the concentrations of nitrates, nitrites, and phosphates. WQI values were obtained from ICO pollution indices. The pollution of the Sacha area is significant, WQI = 0.292, which represents an advanced degree of pollution, since increased BOD values correspond to a high load of organic pollutants. They can originate from household, agricultural, industrial, and soil erosion waste. Likewise, the Sacha River has an ICOSUS = 0.16, which renders water treatment difficult, without impacting human health. Calculated WQI values reveal that the water quality of the Sacha, Basura and Coca rivers is low, being highly contaminated. In contrast, the Huamayacu, Jivino Rojo, Jivino Negro, and Jivino Blanco rivers are commonly polluted.

Advancing characterization of VOC diffusion in indoor fabrics: A dual-porosity modeling approach

Volatile organic compounds (VOCs) are major chemical pollutants in indoor air. Indoor fabrics, such as curtains, carpets, sofas, and clothes, strongly adsorb VOCs due to their high loading rates and large specific surface areas. The desorption of VOCs from these fabrics can act as a secondary source, worsening indoor air pollution and prolonging its effects. The diffusion coefficient is a key parameter that determines the source-sink properties of fabrics. In this study, the VOC diffusion characteristics in fabrics were investigated through microstructural examination, mass transfer analysis, and environmental chamber experiments. Yarn and fiber gaps were identified as dual mass transfer channels within the fabrics and were represented using two distinct fractal models. A dual-porosity medium (DPM) model, based on these fractal representations, was developed to predict the VOC diffusion coefficients in indoor fabrics and was validated via experiments under various environmental conditions and fabric-VOC combinations. The results highlight the significant impact of fabric structure and composition on VOC adsorption and emission dynamics. The validated DPM model provides a comprehensive approach to predicting VOC diffusion in fabrics, providing a more accurate method for assessing indoor air quality and fabric-mediated human exposure.

The Influence of Employment Stress On the Academic Performance of Working Students: Perspectives from Pakistan

One must grasp stress's intricacy to develop and implement stress-reduction strategies. Employment-related stress on academic performance is becoming an acute concern for psychological and mental health in Pakistan. The current research focuses on how employment-related stress interferes with graduate students' academic performance in Parachinar, District Kurram Khyber Pakhtunkhwa, Pakistan. This investigation applies quantitative methods—the Govt. Postgraduate College Parachinar, District Kurram, Khyber Pakhtunkhwa Pakistan, completed a standardized questionnaire to 180 students from various academic disciplines. The findings illuminate stress's intricacy. It may be utilized to establish and encourage more efficient and achievable strategies or techniques that improve academics and job satisfaction, inspiration, and effectiveness at the individual and organizational levels. The research study concluded that 81.67% of male students suffered from employment stress. Student stressors include workload (31.67%), lack of time management (9.44%), interpersonal conflicts (20.00%), high study load (21.11%), and financial problems (17.78%), and the coping strategies being adopted by these students; Moral support (13.89%), Social support (30.00%), Financial support (45.00%), and Job enrichment (11.11%). The research concludes that addressing the highlighted concerns, counselling, and other successful coping strategies may alleviate academic and employment stress.