High Flow Conditions Research Articles

Optimized Design of a Multistage Centrifugal Pump Based on Volumetric Loss Reduction by Auxiliary Blades

Throat ring leakage is a major factor deteriorating the performance of multistage centrifugal pumps. This paper focuses on the optimization of multistage centrifugal pumps by incorporating the principle of the Tesla valve and adding an auxiliary set of blades to the impeller body. By changing the direction and magnitude of the leaking fluid’s flow, the leakage volume of the impeller throat ring is reduced. The study results demonstrate that the experimental error in head calculation with numerical simulation at the optimal working condition was 0.65%, verifying the accuracy of the numerical simulation method. The leakage volume of the throat ring decreased by up to approximately 28.99% compared to the original structure, which significantly increased the pump’s head and overall efficiency. Near the optimal operating point, the pump’s head and overall efficiency increased by approximately 8.1% and 8.7%, respectively. The larger the flow rate, the greater the improvement in the pump’s head and total efficiency. Near high-flow operating conditions, the pump’s head and overall efficiency increased by approximately 116.45% and 110.84%, respectively. The auxiliary blade structure introduces a non-contact seal which, compared to traditional seal structures, improves seal life and reduces seal costs. Additionally, the auxiliary blades can shift the optimal operating point of the multistage centrifugal pump towards a higher flow rate, improving the pump’s delivery capability.

Habitat requirements of Myriophyllum alterniflorum DC. in river stands of the Upper Palatinate Forest, Bavaria

Biodiversity loss is, at present, one of the most severe global environmental issues. However, more demanding species are put at greater risk than generalists. Knowledge of the habitat requirements of threatened species is essential for defining the levels at which nature conservation efforts should prospectively operate. This study describes the habitat niche of the macrophyte species Myriophyllum alterniflorum DC., based on its occurrence along environmental gradients of sediments, flow velocity, turbidity, depth and shade on five brooks of the Upper Palatinate Forest, Bavaria. To examine the transregional validity of our results, we first carried out an analysis on the Pfreimd River and defined the outcomes as a reference. We then defined a transfer system for the other four brooks with M. alterniflorum occurrences, repeated the analysis and compared the results. We found a general pattern of preferred habitat conditions in combination with a regional aspect influencing the species distribution in each brook. We, suggest a broader formulation of habitat characteristics when aiming to describe a transregional pattern. Instead of preferences, we defined local extinction criteria for this species, namely: i) sediment with saprobic fraction, ii) stagnation of flow velocity, iii) strong turbidity iv) shading > 75% and v) water depth > 100 cm. Furthermore, we found that eutrophication is less effective under high-flow conditions. With its high demands on water quality, M. alterniflorum overlaps with the requirements of other endangered species. Therefore, conservation efforts should focus on promoting high-quality habitats, which include sustainable land management approaches at the catchment level.

Effects of hydraulic conditions on biofilm detached in drinking water distribution system

It is well documented that after the water has been treated in the treatment plant, the quality of drinking water is degraded during transport to consumers inside the drinking water distribution system (DWDS). One of the critical reasons for altering drinking water quality is the biofilm detached from the pipe wall to the bulk water. In this paper, the effects of hydraulic conditions such as flow velocity and flow direction, on the biofilm were investigated. The results show that, compared with other flow conditions, the biofilm is the thickest (267.4 μm) and the adhesion force is the lowest under the fluctuant flow velocity. The fluctuant flow velocity increased the relative abundance of Sphingobium and Blastomonas, decreased the relative abundance of Dechloromonas and Sediminibacterium. The Sphingobium with strong environmental adaptability and metabolic capacity could accelerate the growth of biofilm under fluctuant flow velocity conditions. The abundance of functional genes that could reflect microbial metabolic capacity in the biofilm under fluctuant flow velocity conditions is significantly higher than that under other hydraulic conditions. The total number of bacteria in the biofilm under reverse flow conditions was 31.48 %–32.01 % and 47.97 %–71.38 % lower than that under low and high flow conditions, respectively, indicating that the shear force generated by the reverse flow had resulted in biofilm detachment. This study improved our understanding of the influence of different hydraulic conditions on biofilms in the DWDS and helped us understand how to operate the DWDS without causing additional biofilm detachment.

Fluvial Morphology as a Driver of Lead and Zinc Geochemical Dispersion at a Catchment Scale

Metal-mining exploitation has caused ecosystem degradation worldwide. Legacy wastes are often concentrated around former mines where monitoring and research works are mostly focused. Geochemical and physical weathering can affect metal-enriched sediment locations and their capacity to release metals at a catchment scale. This study investigated how fluvial geomorphology and soil geochemistry drive zinc and lead dispersion along the Nant Cwmnewyddion (Wales, UK). Sediments from different locations were sampled for geochemical and mineralogical investigations (portable X-ray fluorescence, scanning electron microscope, X-ray diffraction, and electron microprobe analysis). The suspended sediment fluxes in the streamwater were estimated at different streamflows to quantify the metal dispersion. Topographical and slope analysis allowed us to link sediment erosion with the exposure of primary sulphide minerals in the headwater. Zinc and lead entered the streamwater as aqueous phases or as suspended sediments. Secondary sources were localised in depositional stream areas due to topographical obstruction and a decrease in stream gradient. Sediment zinc and lead concentrations were lower in depositional areas and associated with Fe-oxide or phyllosilicates. Streamwater zinc and lead fluxes highlighted their mobility under high-flow conditions. This multi-disciplinary approach stressed the impact of the headwater mining work on the downstream catchment and provided a low-cost strategy to target sediment sampling via geomorphological observations.

P14: Degradation of High Molecular Weight Multimers of von Willebrand Factor under Whole Blood Conditions in High Turbulent Flow: Implications for Continuous Flow Left Ventricular Assist Devices

Background: High turbulent flow often found in continuous flow left ventricular assist devices (cf-LVADs) is believed to cause acquired von Willebrand Syndrome (AvWS). Our group recently published a study on the kinetic and dynamic effects of various flows on the loss of high molecular weight multimers (HMWMs) of von Willebrand factor (vWF). In the study, we applied high shear to citrated human platelet-poor plasma (PPP) and characterized the flow by Reynolds number (Re). The present study aims to extend upon our previous findings by investigating the degradation of HMWM under whole blood conditions at higher flow conditions to be characterized by energy dissipation rate and clinically relevant exposure times previously employed. Methods: Diluted ovine blood with a hematocrit of 25%, dynamic viscosity of 3.0 cP and density of 1030 kg/m3 was flowed through a custom high shear rotary device. The device is designed to provide a fully controlled exposure time, texp and flow regime. The flow rate was set at 1.75 ml/sec, 0.76 ml/sec, or 0.38 ml/sec, resulting in an exposure time of 22 ms, 50 ms, or 100 ms, respectively. The dynamic flow condition was controlled by the speed of the rotor, ω, and characterized by the energy dissipation rate per unit mass, ε. The ω of 10k, 12k, 15k, 18k, 20k, and 22k RPM were applied, and the corresponding ε were estimated by running a series of large eddy simulations (LES). After each run, a 0.5 ml sample solution was collected, frozen in dry ice immediately, and shipped to the Blood Center of Wisconsin for multimer analysis. The amount of multimer degradation at each testing condition was assessed with respect to the mean of the initial concentration of HMWM of vWF in the controls. Results: The results show that the loss of HMWM at all given exposure times increases in a logarithmic manner within the extended flow conditions (Fig. 1A). The loss of HMWM versus energy dissipation rate at given texp is shown in Fig. 1B. It is noted that as the flow becomes more chaotic, the loss of HMWM appears to be primarily dominated by the energy dissipation rate while the exposure time to chaotic flow becomes less significant. It is not clear if the less significant effect of kinetics at relatively high flow conditions (>18k RPM) is because there are no more HMWM left to be cleaved by ADAMTS13, an enzyme that cleaves vWF. The results are consistent with our previous observations using human PPP, in that both flow conditions and exposure time play crucial roles in the destruction of HMWM. Conclusion: This study demonstrated the relative roles of flow and exposure time using whole blood to characterize the loss of HMWM in terms of energy dissipation rate and exposure time. The findings have the potential to assist in the design and optimization of blood pumps, ultimately leading to improved clinical outcomes for patients with AvWS.

Comparison of artificial neural networks and reservoir models for simulating karst spring discharge on five test sites in the Alpine and Mediterranean regions

Abstract. Hydrological models are widely used to characterize, understand and manage hydrosystems. Lumped parameter models are of particular interest in karst environments given the complexity and heterogeneity of these systems. There is a multitude of lumped parameter modelling approaches, which can make it difficult for a manager or researcher to choose. We therefore conducted a comparison of two lumped parameter modelling approaches: artificial neural networks (ANNs) and reservoir models. We investigate five karst systems in the Mediterranean and Alpine regions with different characteristics in terms of climatic conditions, hydrogeological properties and data availability. We compare the results of ANN and reservoir modelling approaches using several performance criteria over different hydrological periods. The results show that both ANNs and reservoir models can accurately simulate karst spring discharge but also that they have different advantages and drawbacks: (i) ANN models are very flexible regarding the format and amount of input data, (ii) reservoir models can provide good results even with a few years of relevant discharge in the calibration period and (iii) ANN models seem robust for reproducing high-flow conditions, while reservoir models are superior in reproducing low-flow conditions. However, both modelling approaches struggle to reproduce extreme events (droughts, floods), which is a known problem in hydrological modelling. For research purposes, ANN models have been shown to be useful for identifying recharge areas and delineating catchments, based on insights into the input data. Reservoir models are adapted to understand the hydrological functioning of a system by studying model structure and parameters.

Application of coupling machine learning techniques and linear Bias scaling for optimizing 10-daily flow simulations, Swat River Basin

Abstract Accurate hydrological simulations comply with the water (sixth) Sustainable Development Goals (SDGs). The study investigates the utility of ANN and SVR, as well as the post-simulation bias treatment of these simulations at Swat River basin, Pakistan. For this, climate variables were lag adjusted for the first time, then cross-correlated with the flow to identify the most associative delay time. In sensitivity analysis, seven combinations were selected as input with suitable hyperparameters. For SVR, grid search cross-validation determined the optimal set of hyper-parameters, while for ANN, neurons and hidden layers were optimized by trial and error. We ran model by using optimized hyperparameter configurations and input combinations. In comparison to SVRs (Root mean square error (RMSE) 34.2; mean absolute error (MAE) 3.0; CC 0.91) values, respectively, ANN fits the observations better than SVR with (RMSE 11.9; MAE 1.14; CC 0.99). Linear bias-corrected simulations greatly improved ANN performance (RMSE 3.98; MAE 0.625; CC 0.99), while the improvement was slight in the case of SVR (RMSE 35; MAE 0.58; CC 0.92). On seasonal scale, bias-corrected simulations remedy low- and high-flow seasonal discrepancies. Flow duration analysis results reveal deviation at low- and high-flow conditions by models, which were then reconciled by applying bias corrections.

Effects of high and low flows on abundances of fish species in Central European headwater streams: The role of ecological species traits

Hydrological variability is considered a major structuring factor for biotic and abiotic processes in freshwater ecosystems and is of particular importance to fish communities. We used hydrological indices to investigate the short intermediate-and long-term effects of high- and low-flow patterns on the population abundances of 17 fish species in headwater streams in Germany. Generalized linear models, on average, explained 54 % of the variability in fish abundance, whereas long-term hydrological indices performed better than indices based on shorter periods. Three clusters of species were differentiated in their response patterns to low-flow conditions. Cold stenotherm and demersal species were susceptible to high frequency and long duration but tolerant to the magnitude of low-flow events. In contrast, species with a more benthopelagic habitat preference and tolerance to warmer water were susceptible to magnitude but tolerated larger frequencies of low-flow events. The euryoecious chub (Squalius cephalus), tolerating both long durations and large magnitudes of low-flow events, formed its own cluster. Species responses to high flows were more complex and five clusters of species were differentiated. Species with an equilibrium life history strategy were positively affected by longer durations of high-flow conditions, which may allow them to take advantage of the extended floodplain, whereas opportunistic and periodic species significantly differed by thriving in events characterized by high magnitude and frequency. These response patterns of fish species to high and low flows help understand species-specific risks when hydrological conditions are altered by climate change or direct human intervention.

Flood generating mechanisms investigation and rainfall threshold identification for regional flood early warning

A cost effective and easily applied methodological approach for the identification of the main factors involved in flood generation mechanisms and the development of rainfall threshold for incorporation in flood early warning systems at regional scale is proposed. The methodology was tested at the Pinios upstream flood-prone area in Greece. High frequency monitoring rainfall and water level/discharge time-series were investigated statistically. Based on the results, the study area is impacted by “long-rain floods” triggered by several days long and low-intensity precipitation events in the mountainous areas, that saturate the catchment and cause high flow conditions. Time lag between the peaks of rainfall and water level was 17–25 h. The relationship between cumulative rainfall Rsum on the mountainous areas and maximum water level MaxWL of the river at the particular river site can be expressed as: MaxWL = 1.55ln(Rsum) − 3.70 and the rainfall threshold estimated for the mountainous stations can be expressed as: Rsum = 20.4*D0.3, where D is the duration of the event. The effect of antecedent moisture conditions prior each event was limited to the decrease of the time lag between rainfall and water level response. The limitations of the specific methodological approach are related to the uncertainties that arise due to the other variables contributing to the complex flood generating mechanisms not considered (e.g., the effect of snowmelt and air temperature, soil characteristics, the contribution of tributaries, or the inadequate maintenance of river network that may cause debris accumulation and river bank failure).

Probability-Based Rule Curves for Multi-Purpose Reservoir System in the Seine River Basin, France

Multiple reservoir operation is of paramount importance due to tradeoffs in water supply and their cost functions. Understanding this complexity is important for optimizing water supply and increasing synergies gained from the joint operation. Therefore, this study aimed to develop a conceptual framework for addressing the effects of climate change on water security under the operating rules of the multiple reservoir system in northern France. A dynamic programming approach (DP) was employed to find the cost–benefit analysis that best fit with the objectives of reservoir operation, while the space rule was applied to balance the available space in each reservoir of a parallel system. A finite-horizon optimal regulation was then adopted for determining daily reservoir storage based on probability-based rule curves. The results indicated that the predicted inflow during the drawdown–refill cycle period to the Marne and Pannecière reservoirs would be the largest and lowest, respectively. The proposed upper rule curves during high-flow conditions suggested that the release from Aube reservoir should be postponed from July to August until September. At 50- and 100-year return periods, quite a high release rate from Seine and Marne reservoirs was observed during the dry season. A decrease in future water supply from Pannecière reservoir was found during summer, while the withdrawal in November could cause excessive water in the Seine tributary and Paris City. Under low-flow conditions in all return periods, the proposed lower rule curves recommended that the reservoir storage should go below the current operating rule, with a clear difference in July (the largest in Marne and the smallest in Pannecière) and almost no difference in November. Moreover, the web-based support system IRMaRA was developed for revising operating rules of four main reservoirs located in the Seine River Basin. The novelty of this modeling framework would contribute to the practice of deriving optimal operating rules for a multi-reservoir system by the probability-based rule curve method. Based on the evaluation of the effects of applying the estimated reservoir storage capacity under different return periods, both less overflow and water shortage represented by different levels of quantity and severity can be expected compared to the existing target storage at specified control points. Finally, the obtained finding revealed that the application of dynamic programming for reservoir optimization would help in developing a robust operating policy for tackling the effects of climate change.

Impacts of hydrodynamic conditions and microscale surface roughness on the critical shear stress to develop and thickness of early-stage Pseudomonas putida biofilms.

Biofilms can increase pathogenic contamination of drinking water, cause biofilm-related diseases, alter the sediment erosion rate, and degrade contaminants in wastewater. Compared with mature biofilms, biofilms in the early-stage have been shown to be more susceptible to antimicrobials and easier to remove. Mechanistic understanding of physical factors controlling early-stage biofilm growth is critical to predict and control biofilm development, yet such understanding is currently incomplete. Here, we reveal the impacts of hydrodynamic conditions and microscale surface roughness on the development of early-stage Pseudomonas putida biofilm through a combination of microfluidic experiments, numerical simulations, and fluid mechanics theories. We demonstrate that early-stage biofilm growth is suppressed under high flow conditions and that the local velocity for early-stage P. putida biofilms (growth time < 14 h) to develop is about 50 μm/s, which is similar to P. putida's swimming speed. We further illustrate that microscale surface roughness promotes the growth of early-stage biofilms by increasing the area of the low-flow region. Furthermore, we show that the critical average shear stress, above which early-stage biofilms cease to form, is 0.9 Pa for rough surfaces, three times as large as the value for flat or smooth surfaces (0.3 Pa). The important control of flow conditions and microscale surface roughness on early-stage biofilm development, characterized in this study, will facilitate future predictions and managements of early-stage P. putida biofilm development on the surfaces of drinking water pipelines, bioreactors, and sediments in aquatic environments.

Common Failures in Hydraulic Kaplan Turbine Blades and Practical Solutions.

Kaplan turbines, as one of the well-known hydraulic turbines, are generally utilized worldwide for low-head and high-flow conditions. Any failure in each of the turbine components can result in long-term downtime and high repair costs. In a particular case, if other parts are damaged due to the impact of the broken blades (e.g., the main shaft of the turbine), the whole power plant may be shut down. On the other hand, further research on the primary causes of failures in turbines can help improve the present failure evaluation methodologies in power plants. Hence, the main objective of this paper is to present the major causes of Kaplan turbine failures to prevent excessive damage to the equipment and provide practical solutions for them. In general, turbines are mainly subjected to both Internal Object Damage (IOD) and Foreign Object Damage (FOD). Accordingly, this paper presents a state-of-the-art review of Kaplan turbine failures related to material and physical defects, deficiencies in design, deficits in manufacturing and assembly processes, corrosion failures, fatigue failure, cavitation wear, types of cavitation in hydro turbines, hydro-abrasive problems, and hydro-erosion problems. Eventually, the authors have attempted to discuss practical hints (e.g., nanostructured coatings) to prevent damages and improve the performance of Kaplan turbines.

Enhanced slurry erosion resistance of low friction and highly hydrophobic halloysite-fluoro-polysilsesquioxane coatings

Multifunctional coatings were obtained by a sol-gel co-condensation of a fluorinated silane and tetraethoxysilane over activated Halloysite nanotubes (hHNT). They were applied onto epoxy based substrates (neat epoxy or hHNT loaded) with different curing conditions. The coatings characterization showed low friction and high hydrophobicity. The coefficient of friction against stainless steel was 0.1, according to the nanoscratch test and the advancing contact angles reached values in the range 135–145°. The materials were subjected to a slurry erosion test under high speed flow condition and wettability was used to characterize the surface integrity over erosion-cumulative time periods. Fluorine containing coatings exhibited an outstanding resistance to the high speed slurry erosion (HSSE). After 1 h of HSSE test, average advancing contact angles of 145° were measured for the fluorinated samples. The high hydrophobicity of the coatings showed a correlation with the erosion resistance, while the substrate showed no effect. An explanation of the cushioning effect of hydrophobicity upon erosion wear is given, based on wall-detached eddies on the boundary layer.

Changes in water flow alter community dynamics in oyster reefs

AbstractFluid (air or water) movements are key determinants of living systems from cellular to community levels of organization. Water flow can influence individual fitness and local population dynamics, but less is known about the collective response of natural communities to alteration in water flow because parameter responses to flow may be additive, juxtaposed, or interactive. To examine how changes in water flow affected initial larval settlement patterns of epifaunal and infaunal animals, colonization of larger individuals, and prey survival, we manipulated water flow (−50% or +47%) in situ using large wooden channels over small experimental oyster reefs. To test whether initial settlement patterns were additive or influenced by early post‐settlement processes (i.e., predation or competition reduced the densities), we compared patterns in short‐duration trials (two weeks) to those in longer duration deployments (six weeks). We found that minor changes in water flow (5–10 cm s−1) resulted in large changes in settlement of many species, predation levels, and the modification of initial settlement patterns. Settlement (two‐week intervals) and subsequent recruitment (six‐week intervals) increased for several species as flow rate increased. For most species, this relationship peaked at mid‐level flows (mud crabs, barnacles, and bivalves), whereas others (oysters) continued to increase with higher flow rates. Settlement patterns were best preserved in recruitment under high flow conditions where post‐settlement mortality was lower. Collectively, our results demonstrate how biological and physical processes are coupled in oyster reef systems, with relatively minor changes in water flow affecting pre‐ and post‐settlement processes.

Coupling of iron and dissolved organic matter in lakes–selective retention of different size fractions

Increasing concentration of iron (Fe) is observed in many boreal lakes, such as for the present study in Oslo Østmark, SE-Norway (1983–2018). As Fe-regulating processes are complex and dynamic, the link between mobilizing and retention processes is still not well understood. A seasonal study (2017–2018) from two headwaters, with medium and high dissolved organic matter (DOM) concentrations, showed that the loading of Fe to the lakes was highly dependent on flow conditions. Significantly higher values of Fe were related to autumn and winter periods with high runoff of highly colored and aromatic DOM compared to a severe drought period with minimum Fe values in the lakes. Compared to DOM, a significantly larger part of Fe was in a colloidal form, and a size-selective process (dependent on flow and water retention time) seemed to preferentially settle Fe compared to DOM. In contrast to Fe, the variability in DOM concentrations was moderate through the whole year. However, there were significant changes in the spectroscopic properties of DOM, with decreased fluorescence intensity and increased spectral slope during the warm dry season, indicating increased importance of DOM turnover in the lake. As Fe was transported from the catchment during high flow condition, at the same time as the oxic form of sulfur (SO42−), there was no sign of retention of Fe as FeS. We conclude that the mobilization and retention of compounds that are mainly in a colloidal form, such as Fe, are especially vulnerable to changes in flow conditions, suggesting increased variation in Fe levels in a future climate with increased frequency of flooding and drought episodes.

Land-use-based freshwater sediment source fingerprinting using hydrogen isotope compositions of long-chain fatty acids

Rapidly changing land use patterns and frequent extreme weather events have resulted in an increased sediment flux to freshwater systems globally, highlighting the need for land-use-based sediment source fingerprinting. Application of variability in hydrogen isotope compositions (δ2H values) of vegetation-specific biomarkers from soils and sediments is relatively underexplored for land-use-based freshwater suspended sediment (SS) source fingerprinting, but has the potential to complement the information from routinely applied carbon isotope analysis and provide new insights. We analysed δ2H values of long-chain fatty acids (LCFAs) as vegetation-specific biomarkers in source soils and SS collected from the mixed land use Tarland catchment (74 km2) in NE Scotland, to identify stream SS sources and quantify their contributions to SS. Plant growth form was the primary control on source soils LCFAs (n-C26:0, n-C28:0, n-C30:0) δ2H variability, while the isotopic composition of source water had no significant control. Forest and heather moorland soils covered with dicotyledonous and gymnosperm species were differentiated from arable land and grasslands soils covered with monocotyledonous species. SS samples collected for fourteen months from the Tarland catchment with a nested sampling approach showed monocot-based land use (cereal crops, grassland) to be the major source of SS with 71 ± 11% contribution on catchment-wide scale averaged throughout the sampling period. Storm events after a dry summer period and sustained high flow conditions in the streams during autumn and early winter suggested enhanced connectivity of more distant forest and heather moorland land uses covering relatively steep topography. This was shown by an increased contribution (44 ± 8%) on catchment-wide scale from dicot and gymnosperm-based land uses during the corresponding period. Our study demonstrated successful application of vegetation-specificity in δ2H values of LCFAs for land-use-based freshwater SS source fingerprinting in a mesoscale catchment where δ2H values of LCFAs were primarily controlled by plant growth forms.

Source apportionment of mine contamination across streamflows

Globally, metals released by mine waste represent a challenge for protecting water quality and ecosystems. Understanding metal dispersion in catchments is critical for developing efficient remediation strategies and reducing contamination from mining activities. Efforts to address the issue have been constrained by diffuse sources and variation of source contributions across streamflows. In the UK, metal source apportionment is typically addressed using monitoring strategies with low spatial resolution, which can underestimate the contribution of diffuse sources. In this proof-of-concept study, diffuse sources were accurately apportioned in a mining-impacted catchment in Mid-Wales (UK), using a hydrogeochemical approach with combined continuous tracer injections, gulp injections, and streambed sediment geochemistry. The continuous tracer injections identified a major Zn and Pb point source, diffuse sources due to mine waste tip runoff, and potential groundwater contributions. Variations in source contributions were estimated during high and low flow conditions, with Zn having similar sources and importance across streamflows and Pb being released mainly from overground tips during high flow conditions (22% Pb under low flow and 80% Pb under high flow). The distribution of metal-bearing sediment along the stream sheds light on metal release mechanisms across streamflow conditions. This hydrogeochemical approach for source apportionment, builds on common monitoring methods, and represents a substantial advance in accounting diffuse mine contamination sources, understanding potential metal release mechanisms, and designing remediation strategies.

Streamflow duration curve to explain nutrient export in Midwestern USA watersheds: Implication for water quality achievements

As part of federal programs to reduce nutrient pollution, states across the Midwest have developed nutrient reduction strategies, which focus on implementation of agricultural conservation practices (ACPs) or best management practices (BMPs). Despite several decades of federal investment in implementing ACPs/BMPs for reducing nutrient pollution, nutrient pollution is a continuing and growing challenge with profound implications for water quality and public health as well as ecological functions. Pollutant transport depends on water and sediment fluxes, which are governed by local hydrology. Therefore, knowing how flow conditions affect nutrients export is critical to develop effective nutrient reduction strategies. The objective of this study was to investigate the role of streamflow duration curve in controlling nutrient export in the western Lake Erie Basin and the Mississippi River Basin. To achieve this goal, we used long-term monitoring data collected by the National Center for Water Quality Research. We focused on the percentage of the annual pollutant load (nitrate-NO3-N, dissolved reactive phosphorus-DRP, total phosphorus-TP, and total suspended solids-TSS) exported during five flow intervals that spanned the flow duration curve: High Flows (0–10th percentile), Moist Conditions (10–40th percentile), Mid-Range Flows (40–60th percentile), Dry Conditions (60–90th percentile), and Low Flows (90–100th percentile). The results show that the top 10% of flows (i.e., high flows) transported more than 50% of the annual nutrient loads in most of the studying watersheds. Meanwhile, the top 40% of flows transported 54–98% of the annual NO3–N loads, 55–99% of the annual DRP loads, 79–99% of the annual TP loads, and 86–100% of the annual TSS loads across the studying watersheds. The percentage of the annual loads released during high flows increased as the percentage of the agricultural land use in the watershed increased, but it decreased as the watershed area increased across different watersheds. Finally, flow condition/nutrient export relationships were consistent over studying period. Therefore, reducing nutrient loads during high flow condition is the key for effective nutrient reduction.

Ground Testing Facility for Hypersonic Materials

A plasma wind tunnel capable of creating high enthalpy flow conditions is required to overcome the critical performance challenges when developing thermal protection systems

Spatially distributed water quality responses to freshwater discharge in a tropical estuary, Hilo Bay, Hawai'i.

Hilo Bay, Hawai'i, is an estuary of great importance to its neighboring coastal community, but it is threatened by impaired water quality indicated by excessive turbidity and chlorophyll a associated with river discharges of sediments and nutrients. The Wailuku River in the western half of the bay is the primary source of freshwater discharge, hypothesized here to form a surface water-dominant half of the bay with different water quality traits than the groundwater-dominant, eastern half of the bay where the spring-fed Wailoa River discharges. The water quality of both halves of the bay over different flow conditions of the Wailuku River is examined in this study using spatially distributed water quality sampling which collects hundreds of samples in either half of the bay at a distance of about every 40m. The dense sample shows significant differences between the two halves of the bay, with greater salinity dilution and turbidity in the surface water-dominant area. Both salinity and turbidity have a predictable relation to discharge, with salinity decreasing and turbidity increasing in higher flow conditions. Chlorophyll a, however, has a more complex relation to discharge, as chlorophyll a concentrations are greatest in high-flow conditions, but this may be because the water quality samples were collected in different seasons. Furthermore, significantly greater chlorophyll a concentrations in the groundwater-dominant half of the bay in low-flow conditions show that discharge may be spuriously correlated to chlorophyll a, and further studies of the effects of surface water discharge on chlorophyll a concentrations are warranted.