High-density Fraction Research Articles

The Effect of Lower Limb Pressotherapy Treatment on Selected Rheological and Biochemical Indices of Blood in Young, Healthy Women.

Background: Intermittent pneumatic compression is a non-invasive therapeutic technique that has been gaining popularity in recent years due to its potential use in many areas of medicine. It can be successfully used alone or in combination with other therapeutic methods. The aim of this study was to investigate whether and how a series of pressotherapy treatments on the lower limbs affects the rheological properties of blood (blood count, red blood cell deformability and aggregation, and blood viscosity), lipid profile (total cholesterol, triglycerides, low-density lipoprotein, and high-density lipoprotein), and renal profile (urea, creatinine, and estimated glomerular filtration rate) in young, healthy women. Methods: The study group consisted of 15 healthy women aged 20-26 (22.5 ± 1.5), without chronic diseases and not practicing competitive sports. The participants underwent a series of 10 lower limb pressotherapy treatments. A single treatment lasted 30 min and each time the pressure used during the treatment was individually selected according to the participants' preference. The first blood test was performed a week before the treatments; the second on the day of the start of treatment, but before the pneumatic massage; the third after the completed series of pressotherapy treatments; and the fourth a week after the completed series of treatments. Results: In the conducted study, the analysis of the values of the complete blood count showed the following: a significant decrease in red blood cell count, hemoglobin, average hemoglobin concentration in erythrocytes, average red blood cell volume, average hemoglobin mass in red blood cells; a significant increase in average red blood cell volume; and an average hemoglobin mass in red blood cells. The analysis of the values of rheological parameters showed the following: a significant decrease in elongation indices 0.58, 1.13, 4.24, 15.95, 30.94, and 60.00; blood viscosity; the aggregation index; the degree of complete aggregation; and a significant increase in elongation indices 0.30, 1.13, 8.23, 30.94, 60.00; blood viscosity; the degree of complete aggregation; and the half-time of complete aggregation. A decrease in the concentration of low-density lipoprotein and high-density lipoprotein fractions was also noted. No significant changes were found in the values of total cholesterol and triglycerides, as well as in renal profile elements. Conclusions: The application of a series of 10 lower limb pressotherapy treatments has a beneficial effect, with a decrease in blood viscosity and the aggregation index, and an increase in the elongation index at shear stress from 0.30 [Pa] to 8.23 [Pa] in young, healthy women. A series of 10 lower limb pressotherapy treatments may affect the decrease in the values at high shear stress forces of 30.95 [Pa] and from 60.00 [Pa] in young, healthy women. The use of a series of 10 lower limb pressotherapy treatments increases the values of hemoglobin, the average red blood cell volume, and the average hemoglobin concentration in erythrocytes, and also reduces the values of red blood cell count, average hemoglobin mass in red blood cells and low-density lipoproteins and high-density lipoproteins in young, healthy women (it also does not cause any adverse changes). The use of pressotherapy on the lower limbs seems to be an effective element of the multi-component prevention of circulatory system diseases.

Transport and stability in sustained high qmin , high βN discharges on DIII-D

To address the needs for a fusion pilot plan design, DIII-D/EAST joint experiments on DIII-D have demonstrated high normalized beta β N ∼ 4.2, toroidal beta β T ∼ 3.3% with q min > 2, q 95 ⩽ 8 sustained for more than six energy confinement times in high poloidal beta regime. The excellent energy confinement quality (H 98y2 ∼ 1.8) is achieved with an internal transport barrier at high line-averaged Greenwald density fraction f Gr > 0.9. The trapped gyro-Landau fluid (TGLF) modeling of the transport characteristics shows that the beam-driven rotation does not play an important role in the high confinement quality. The modeling also captures very well several transport features, giving us confidence in using integrated modeling to project these experimental results to future machines. The high-performance phase is terminated by fast-growing modes triggered near the n = 1 ideal-wall kink stability limit. New radio frequency (RF) capabilities for off-axis current drive could remove the residual ohmic current to achieve a fully non-inductive state, and improve the mode–wall coupling to increase the ideal-wall β N limit, enabling sustainment of the fully non-inductive high performance plasma in stationary conditions.

Cholesterol-Lowering and Antioxidant Effects of Pork-Liver Protein Hydrolysate in Otsuka Long-Evans Tokushima Fatty Rats.

In this study, we investigated the effects of a porcine liver protein hydrolysate (PLH) diet on lipid metabolism in Otsuka Long-Evans Tokushima Fatty (OLETF) rats, a model of type II diabetes. OLETF rats (20-wk-old males) were pair-fed with either a PLH diet containing 20% PLH or a casein diet for 14 wk. Dietary PLH significantly lowered serum cholesterol and phospholipid concentrations, mainly by decreasing low-density lipoprotein and high-density lipoprotein fractions. Fecal cholesterol was significantly increased in the PLH diet group; however, the total bile acid concentration in the feces was not significantly different between the groups. In addition, the PLH diet significantly decreased serum thiobarbituric acid reactive substance concentrations. These results suggest that dietary PLH exerts hyperlipidemic and antioxidant effects, indicating that it is a novel functional food ingredient.

Tailoring the microstructure and soft magnetic properties of (Fe0.83B0.11Si0.02P0.03C0.01)99.5Cu0.5 nanocrystalline alloy based on the rapid annealing

In this work, the effects of annealing temperatures and time on the microstructure and soft magnetic properties of (Fe0.83B0.11Si0.02P0.03C0.01)99.5Cu0.5 nanocrystalline alloy were investigated using a new rapid annealing process. The results show that at each annealing temperature, there exists an annealing time for optimum soft magnetic properties. The annealing temperature and time were further optimized, and excellent properties with high saturation magnetic induction Bs of 1.79 T and low coercivity Hc of 2.7 A/m were obtained by annealing at 431 °C for 150 s. A microstructure consisting of uniform and fine α-Fe(Si) grains with high number density and high crystallization volume fraction was found to be the key to ensure high Bs and low Hc. However, with increasing annealing time, it was found that α-Fe(Si) grains existed aggregation phenomenon (in the form of high-angle grain boundaries), with the simultaneous precipitation of Fe-B compound precipitated in the residual amorphous matrix. This not only causes the uneven distribution of nanocrystals, but also destroys the competitive effect between nanocrystals and the stability of the structure, thus deteriorating the soft magnetic properties.

Functional organic matter components in mangrove soils revealed by density fractionation

ABSTRACT The mechanisms underlying stabilization of soil organic matter (SOM) in vegetated coastal ecosystems, including mangrove forests, are poorly understood, limiting our ability to predict the consequences of disturbances. Here, we introduce density fractionation to mangrove soils to identify the distribution and properties of the functional components of SOM regarding degradation state, stability, and origin, namely, the free low-density fraction (f-LF), mineral-associated LF (m-LF), and high-density fraction (HF). Three soil cores (1 m) were collected in a mangrove forest on Ishigaki Island, Japan, and cut into 10 cm intervals and analyzed. Although HF was the most abundant, the massive production of mangrove fine roots resulted in a high abundance of LFs throughout the cores, which markedly differed from terrestrial soils. Relative abundance of LFs together accounted for 38–66% of total soil C. The m-LF was as abundant as f-LF and 1.6 times higher in relative abundance than the global average of terrestrial soils. The C/N ratios and δ13C values clearly increased with depth in all fractions, which was attributed to the increased contribution from roots. We found a consistent pattern in Δ14C values of density fractions. HF was the oldest with Δ14C between −149‰ and −97‰ followed by m-LF (between −130‰ and −87‰) and then f-LF (between −89‰ and 78‰), suggesting that mineral association may be pivotal in long-term carbon storage in the mangrove mineral soil. Our analysis successfully identified meaningful functional components of mangrove SOM, yet several questions remained unanswered, including a large variability in Δ14C in different cores. Future studies would benefit from a coupled analysis of the quantity and quality of density fractions and geochemical factors in mangrove soils.

Enhancement of optical and radiation shielding properties in calcium–magnesium silicate bioactive glasses through Na2O and P2O5 additives

The present study investigates the influence of Na2O/MgO and P2O5/SiO2 substitutions on the structure and protective properties of bioactive glasses composed of 32CaO–19MgO–0.5P2O5–0.5CaF2–48SiO2 (mole %). The glass samples are prepared using the conventional melt-quenching method. Optical analyses, including refractive index (n), molar refraction (Rm), and cationic polarizability (αm), are calculated and discussed to examine structural modifications. Raman spectroscopy is employed for detailed structural analysis. The effects of compositional changes on the protective parameters are thoroughly investigated by theoretically determining mass attenuation using the newly developed Phy-X/PSD software and XCOM programs, which are then experimentally confirmed at three selected radioactive isotope energies. Experimental measurements of mass attenuation coefficient follow the sequence: MACG1 > MACG2 > MACG3 > MACG4. Raman spectroscopy results indicate that the glass network primarily consists of silicate and phosphate species as the main structural units. An increase in the molar ratio of Na2O and P2O5 improves the radiation shielding effectiveness of the samples. Among them, sample G5, with the lowest SiO2 and MgO content, exhibits the best shielding characteristics due to its high density and molar fraction of Na2O and P2O5. A correlation between microhardness and protective effectiveness is also established. The obtained results support the potential use of these glasses as dual agents for both radiation shielding and medical devices simultaneously.

Analysis of vitamin K1 and major K2 variants in rat/human serum and lipoprotein fractions by a rapid, simple, and sensitive UHPLC-MS/MS method

Determination of the various forms of vitamin K, which are involved in coagulation and other physiological processes in humans, is challenging and no standardized method is yet available. Therefore, a reliable and practical method was developed to quantify vitamin K levels in serum and additionally in lipoprotein fractions to clarify its distribution. The LC-MS/MS method for the determination of vitamin K1 and the three main isoforms of vitamin K2 (MK-4, MK-7, MK-9) was combined with a gradient ultracentrifugation technique to allow the separation of lipoprotein fractions. The chromatographic separation was carried out on a Kinetex™ C18 column using a mobile phase consisting mainly of methanol. The target analytes were detected by electrospray ionization mass spectrometry. The separation of all four substances was achieved after a simple sample preparation technique based on miniaturized liquid-liquid extraction. Our method of only 8.5 min revealed the levels of the major forms of vitamin K in 59 human and 12 rat sera and confirmed our hypothesis that vitamin K is primarily (about 50 %) found in the high-density lipoprotein fraction. The median concentrations of vitamin K1, MK-4, MK-7, and MK-9 were found to be 1.19, 2.98, 0.43, and < 0.71 nmol/L in human serum and 1.74, 6.75, less than 0.2, and less than 0.5 nmol/L in rat serum, respectively.

Dissolution-induced oxide synthesis using SiO2 microparticles for oxide dispersion strengthening of Fe-based alloys

This study reports on a single-track laser surface alloying process that utilizes SiO2 powder to disperse both SiO2 particles and oxide inclusions in 316L stainless steel for oxide dispersion strengthening (ODS) purposes. In this process, the SiO2 powders partially dissolve in the melt pool, and the released silicon and oxygen atoms nucleate to form oxide inclusions in-situ within the metal matrix. This dissolution-induced oxide synthesis route demonstrated a high potential for ODS, achieving a high particle number density (6.6 × 104 mm−2) and area fraction (3.3%) comparable to that of bulk 316L samples produced via directed energy deposition. The hardness of the SiO2/316L composites reached a maximum of 232.4 HV compared to that of the 316L substrate (average 170.8 HV). The improvement in hardness was theoretically explained and quantified, significantly originating from the enhanced dislocation density strengthening mechanism resulting from the large difference in the coefficient of thermal expansion between SiO2 and 316L.

Hepatic SREBP signaling requires SPRING to govern systemic lipid metabolism in mice and humans

The sterol regulatory element binding proteins (SREBPs) are transcription factors that govern cholesterol and fatty acid metabolism. We recently identified SPRING as a post-transcriptional regulator of SREBP activation. Constitutive or inducible global ablation of Spring in mice is not tolerated, and we therefore develop liver-specific Spring knockout mice (LKO). Transcriptomics and proteomics analysis reveal attenuated SREBP signaling in livers and hepatocytes of LKO mice. Total plasma cholesterol is reduced in male and female LKO mice in both the low-density lipoprotein and high-density lipoprotein fractions, while triglycerides are unaffected. Loss of Spring decreases hepatic cholesterol and triglyceride content due to diminished biosynthesis, which coincides with reduced very-low-density lipoprotein secretion. Accordingly, LKO mice are protected from fructose diet-induced hepatosteatosis. In humans, we find common genetic SPRING variants that associate with circulating high-density lipoprotein cholesterol and ApoA1 levels. This study positions SPRING as a core component of hepatic SREBP signaling and systemic lipid metabolism in mice and humans.

Preparation of morph-genetic aluminum-doped calcium oxide templated from cotton and the calcium looping performance for energy storage in the presence of steam

Calcium looping (CaL), which can be combined with concentrated solar power (CSP) plants, is considered a promising technology for energy storage. To overcome the deactivation of calcium based materials with increasing cycles, a novel morph-genetic aluminum doped calcium oxide was prepared by a biomass template method using limestone, aluminum nitrate and cotton as raw materials. The effects of preparation parameters and heat storage conditions (especially in presence of steam) on the energy storage performance were studied. The results showed that the hollow tubular structure of the biomass template was preserved in the synthesized material and stabilized by the support of Ca12Al14O33. The presence of the hollow microtubular structure resulted in an increased pore volume of the synthesized materials and a change of the pore distribution, promoting the diffusion of CO2. This phenomenon also explained the superior performance of the synthesized material in terms of the apparent kinetic properties and resistance to sintering. The optimal synthesized material had a high energy storage density and carbonation fraction, which were more than three times those of limestone. The presence of steam during calcination served to reduce the calcination temperature and mitigate the sintering effect of CaO. An optimization route combining solar steam system and CaL-CSP system was proposed based on the positive effect of steam, which was promising for high-efficiency energy storage.

Effects of Dietary Halloysite Supplementation on Broiler Chicken’s Blood Parameters, Carcass and Meat Quality, and Bone Characteristics: A Preliminary Study

Abstract The aim of this study was to determine the effect of halloysite supplementation to the complete diets for broiler chickens on selected blood parameters, carcass and organ characteristics, as well as bone and meat traits. The trial was conducted under experimental conditions in a large-scale poultry farm on 18,000 broiler chickens. The one-day broiler Ross 308 chicks were randomly divided into two groups: control (C) and experimental (E) in an amount of 9,000 birds per group. In each group, chicks were separated into five pens (100 m2) with 1800 chicks per pen. The birds were fed granulated complete mixtures without (C group) or with halloysite (E group) distributed in an amount of 1% (based on fresh matter) from the 11 d of life. Analysis revealed that halloysite supplementation to the broiler diet at the level of 1% showed a trend (P = 0.056) towards higher final body weight, significantly improved carcass yield (P = 0.048), and reduced the relative weights of the liver and gizzard (P&lt;0.05). No differences (P&gt;0.05) were observed either in terms of the physicochemical parameters of the broiler chickens’ breast muscles, except a significantly lower b* value of the colour parameter (P = 0.048). In turn, in the blood serum, the addition of 1% halloysite significantly decreased (P&lt;0.05) the content of triglycerides and the total cholesterol and low-density lipoprotein fraction, but did not affect (P&gt;0.05) the high-density lipoprotein fraction, calcium, phosphorus or alkaline phosphate content. Tibia and femur characteristics (weight, length, relative bone weight, bone mineral density, bone mineral content, and breaking strength) were not affected (P&gt;0.05) by the usage of halloysite. In conclusion, supplementation of broiler diet with halloysite in the amount of 1% had beneficial effects on the carcass yield and health status of the animals, without any adverse effect on the bone parameters or meat quality of the broiler chickens.

Measurement of Adenovirus-Based Vector Heterogeneity

Adenovirus vectors have become an important class of vaccines with the recent approval of Ebola and COVID-19 products. In-process quality attribute data collected during Adenovirus vector manufacturing has focused on particle concentration and infectivity ratios (based on viral genome: cell-based infectivity), and data suggest only a fraction of viral particles present in the final vaccine product are efficacious. To better understand this product heterogeneity, lab-scale preparations of two Adenovirus viral vectors, (Chimpanzee adenovirus (ChAdOx1) and Human adenovirus Type 5 (Ad5), were studied using transmission electron microscopy (TEM). Different adenovirus morphologies were characterized, and the proportion of empty and full viral particles were quantified. These proportions showed a qualitative correlation with the sample's infectivity values. Liquid chromatography-mass spectrometry (LC-MS) peptide mapping was used to identify key adenovirus proteins involved in viral maturation. Using peptide abundance analysis, a ∼5-fold change in L1 52/55k abundance was observed between low-(empty) and high-density (full) fractions taken from CsCl ultracentrifugation preparations of ChAdOx1 virus. The L1 52/55k viral protein is associated with DNA packaging and is cleaved during viral maturation, so it may be a marker for infective particles. TEM and LC-MS peptide mapping are promising higher-resolution analytical characterization tools to help differentiate between relative proportions of empty, non-infectious, and infectious viral particles as part of Adenovirus vector in-process monitoring, and these results are an encouraging initial step to better differentiate between the different product-related impurities.

Valorization of South African Coal Wastes through Dense Medium Separation

Sustainable management of coal waste is one of the major environmental concerns for coal mining, whether active or legacy, worldwide. Coal dump deposits demand a large physical area or footprint for disposal of solid waste, change the topography, and generate both pyritic dust and acid rock drainage (ARD) where pyritic coal waste is deposited. The beneficiation of dump deposits or, preferably, of coal waste prior to its dumping can reduce or even eliminate the liabilities related to coal waste management. In this work, dense medium separation studies of coal discards, using heavy liquids, resulted in three pooled fractions from typical South African coal waste discards from the Mpumalanga region for future use: (a) a fraction of low density with increased calorific value; (b) a fraction of intermediate density, rich in ash and acid neutralizing minerals and lower in sulfur; and (c) a fraction of high density, rich in sulfidic minerals including pyrite. The fractions were characterized using particle size analysis, sink-float studies, static tests to predict ARD potential, proximateand ultimate analysis, and gross calorific value. The results showed that approximately 70% of this discard coal is composed of a material of sufficient quality for energy generation in conventional power stations. A pyrite-rich concentrate made up 2% of the total discard mass; comprising more than 45% of the sulfidic mineral present in the feed and displaying no acid neutralizing capacity (ANC). The remaining discard fraction, with intermediate density, presented potential to be used for several ends including soil fabrication, co-disposal or as aggregate material in civil engineering; additional testing to ensure applicability for the selected re-purposing option should be chosen based on proposed use.

The Effect of Physical Separation and Calcination on Enrichment and Recovery of Critical Elements from Coal Gangue

Critical metallic elements in coal gangue have great utilization potential, especially due to the current shortage of these metals. This paper focused on examining the feasibility of physical separation (screening and float-sink tests) and calcination treatment for the enrichment of critical elements (Li, Ga, and rare earth elements plus yttrium (REY)) from coal gangue. The impacts of these enrichment methods on the acid leaching recovery of these elements were then studied. Screening tests indicated that Li and Ga were enriched in &gt;0.125 mm size fraction and the content of REY was highest in &lt;75 μm size fraction. Float-sink tests showed that high-density fractions were enriched in Li and Ga, and low-density fractions were enriched in REY. Physical separation cannot significantly improve the leaching rate of Li, Ga, and REY. Notably, Li, Ga, and REY were enriched significantly, and their acid leaching recoveries were increased by 54~68% after calcination under 400 °C. Sequential chemical extraction tests showed that the majority of insoluble Li, Ga, and REY was converted into soluble forms at the above temperature, which is attributed to the formation of amorphous metakaolinite and the decomposition of organic matter. Based on the results, a conceptually combined flowsheet was proposed for the extraction of Li and Ga from coal gangue.

The nanomechanical nature of cementitious calcium-(alumino)silicate-hydrate under ultra-low temperature attack: An intrinsic transition and the role of aluminum for bottom-up enhancement

Herein, the intrinsic nanomechanical transition of calcium-(alumino)silicate-hydrate (C-(A)-S-H) upon ultra-low temperature attack and the potential role of aluminum incorporation as a bottom-up enhancement strategy are investigated. C-(A)-S-H is experimentally synthesized using an efficient hydrothermal reaction, and statistical AFM-based indentation, nitrogen sorption, SEM, and AFM observations are carried out. Note that the C-A-S-H is clarified in more ordered topographic features than Al-free C-S-H. The nanomechanical measurements reveal that the ultra-low temperature attack provoked the nano-brittleness of C-(A)-S-H. Nevertheless, the nanomechanical degradation is seen for Al-free C-S-H only. This brittle transition is attributed to the rise of the high-density phase fraction, though the elastic moduli of its decomposed phases decrease. In comparison, the brittle transition of C-A-S-H is ascribed to the increasing elastic moduli of its decomposed phases. It is further proved that such transitions are irrelevant to the packing nature of gel grains but involved with the variation of their intrinsic nanomechanical natures since the gel pore systems remain stable under the ultra-low temperature attack. These results advance fundamental knowledge toward developing cryogenic stable cement-based materials from a bottom-up insight.

Comparison of the efficiency of metal recovery from wet- and dry-discharged municipal solid waste incineration bottom ash by air table sorting and milling

Separating high-density fractions from municipal solid waste incineration bottom ash (BA) is a promising approach for collecting metal resources and harmful elements. Herein, the efficiency of the recovery of metals (Cu, Zn, Au, Ag, and Pb) in the high-density fractions of two air-dried BAs discharged from wet-based systems (WBA), was compared with that of two BAs discharged from dry-based systems (DBA). WBAs and DBAs (<8 mm) were sorted using sieving, magnetic separation, milling, and air table sorting techniques. Newton’s separation efficiency was used to evaluate three scenarios that combined various sorting processes. WBA contained high-density fractions (D1, 2.73–3.63 g/cm3) with a density similar to that of D1 in DBA (2.68–3.67 g/cm3), but the surface of the particles was covered by more minerals. When D1, and the metal particles were recovered after the milling of the low-density fractions, the overall separation efficiency in WBA (0.30–0.40) was lower than that in DBA (0.49) because of the lower separation efficiency for Zn and Pb compared to that for the other target metals. In contrast, no significant difference was recorded in the separation efficiency for Cu, Au, and Ag between WBA and DBA. D1 (18000–132000 mg-Cu/kg) and metal particles (29900–199800 mg-Cu/kg) in both WBA and DBA recorded abundant Cu contents. Moreover, the Au content in some D1 was similar to that found in natural ores. The elemental contents and separation efficiency results indicated that D1 and metal particles should be collected from both WBA and DBA.

Influence of rock fragments on preferential flow in stony soils of karst graben basin, southwest China

In karst areas, the distribution of stony soils results from bedrock weathering over time, influencing the development of preferential flow to some extent. In this study, field dye tracing experiments and stereological profile imaging methods were performed to identify the effect of different-sized rock fragments in regolith layer on preferential flow. Results show that 95 % rock fragments (5–250 mm) in karst graben basin are scattered below the 15 cm soil layer. The coarse gravels (20–76 mm) dominated the stony soils of karst graben basin, with high number density and volume fraction, 1.4–3.3 times and 2.1–3.7 times higher than those of the medium gravels (5–20 mm) and cobbles (76–250 mm), respectively. The local effective rock fragments can either promote preferential flow with flow paths along the soil–rock interface or depress it, with the total volume fraction threshold of 30 % (17 % of the coarse gravel). Indices describing the degree of preferential flow development, i.e., the preferential flow ratio and length index, are linearly increasing in relation to the volume fraction. The influence of rock fragments in regolith layer on the preferential flow cannot be ignored and provide directions for the underground hydrological processes in karst stony soils.

Characteristics of lipid spectrum and functional liver tests in patients with nonalcoholic liver steatosis depending on degree of obesity during menopause

Objective. To study the blood lipid spectrum and functional liver tests in women with nonalcoholic liver steatosis (NALS) depending on the degree of obesity during menopause.&#x0D; Materials and methods. Seventy patients with NALS and obesity (NALS-O-M) in menopause with the mean age of 49,9 1,1 years including 24 with increased body mass index (BMI), 20 with the degree 1 obesity, 18 the degree 2 obesity and 8 the degree 3 obesity were examined. The control group involved 30 practically healthy women in menopause without obesity. Blood serum cytolysis, cholestasis and lipid spectrum indicators were studied in both groups.&#x0D; Results. According to the results of biochemical investigation, in the group of patients with NALS-O-M syndrome no cytolysis was observed. In case of marked obesity, cholestasis syndrome by the blood alkaline phosphatase level was identified. Lipid spectrum in patients with NALS-O-M statistically significantly differed from the control: hypercholesterinemia, hypertriglyceridemia, increase in the low- and very low-density lipoproteins as well as calculated index of atherogeneity with decrease in the high-density lipoproteins fraction was registered.&#x0D; Conclusions. A pronounced obesity causes the cholestasis syndrome with an increase in the blood alkaline phosphatase level. Dyslipidemia of different degree of manifestation is registered in all patients with steatosis and obesity during menopause, being more marked in patients with the degree 23 obesity.

Daytime Lipid Metabolism Modulated by CLOCK Gene Is Linked to Retinal Ganglion Cells Damage in Glaucoma

Lipid metabolism is intimately linked to circadian mechanisms and light signaling. Deteriorated photic transduction because of retinal ganglion cell (RGC) loss occurring with glaucoma progression reduces perceived light amplitude, causing circadian disruption. To investigate associations with RGCs, total cholesterol (TC), its low-density (LDL-C) and high-density (HDL-C) fractions, and triglycerides (TG) were measured, under a controlled meal regimen, during daytime hours in 114 patients diagnosed with primary open-angle glaucoma (POAG). RGC damage was assessed by high-definition optical coherence tomography (HD-OCT). Analysis of eight clock, clock-related, and melatonin receptor gene polymorphisms was performed on 19 patients. RGC loss was associated with changes in lipid metabolism in a time-dependent manner. Morning (08:00) values of HDL-C (r = 0.613, p &lt; 0.0001) and TG (r = 0.568, p &lt; 0.0001) correlated positively with RGC global loss, while LDL-C at 08:00 had a weak correlation (r = 0.235; p = 0.012) but showed a strong correlation in the evening (20:00) (r = 0.533, p &lt; 0.0001). The morning–evening gradients (MEGs, changes at 20:00 versus 08:00) in TC and LDL-C changed sign from a negative to a positive association in patients exceeding the 15% two-eye mean GLV threshold. MEG (LDL-C higher in the evening than in the morning) was positive only in POAG patients with the CLOCK_3111 TT genotype.

Meso- and Rac-[bis(3-phenyl-6-tert-butylinden-1-yl)dimethylsilyl]zirconium Dichloride: Precatalysts for the Production of Differentiated Polyethylene Products with Enhanced Properties.

Ansa-zirconocene complexes are widely employed as precatalysts for olefin polymerization. Their synthesis generally leads to mixtures of their rac and meso isomers, whose separation is often problematic. In this contribution, we report on the synthesis of a novel silyl-bridged bis(indenyl)-based metallocene, and on the separation of its rac and meso isomers by simple recrystallization from toluene. The two complexes, activated by methylaluminoxane (MAO), have been used as precatalysts in ethylene/1-hexene copolymerization. Regardless of the reaction conditions, the meso complex outperformed its rac congener. A similar trend was observed by performing the process in the presence of the silica-supported versions of the complexes. This is remarkable, since meso metallocenes generally display lower activities than their rac analogues. Furthermore, the meso isomer generates polymer products that are more in line with the targets for the preparation of a bimodal PE grade made of a lower-MW high-density (HDPE) fraction and a higher-MW linear low-density (LLDPE) fraction.