High Temperature Phase Change Materials Research Articles

Research on NaCl-KCl High-Temperature Thermal Storage Composite Phase Change Material Based on Modified Blast Furnace Slag

The high-temperature composite phase change materials (HCPCMs) were prepared from solid waste blast furnace slag (BFS) and NaCl-KCl binary eutectic salt to achieve efficient and cost-effective utilization. To ensure good chemical compatibility with chlorine salt, modifier fly ash (FA) was incorporated and subjected to high-temperature treatment for the processing of industrial solid waste BFS, which possesses a complex chemical composition. The HCPCMs were synthesized through a three-step process involving static melting, solid waste modification, and mixing–cold pressing–sintering. Then, the influence of the modification method and the amount of SiC thermal conductivity reinforced material on chemical compatibility and thermodynamic performance was explored. The results demonstrate that the predominant phase of the modified solid waste is Ca2Al2SiO7, which exhibits excellent chemical compatibility with chlorine salt. HCPCMs containing less than 50 wt.% chloride content exhibit good morphological stability without any cracks, with a melting temperature of 661.76 °C and an enthalpy value of 108.73 J/g. Even after undergoing 60 thermal cycles, they maintain good chemical compatibility, with leakage rates for melting and solidification enthalpies being only 6.3% and 0.23%, respectively. The equilibrium was achieved when 40 wt.% of chloride salt was encapsulated upon the addition of 10% of SiC, and the incorporation of SiC resulted in an enhancement of thermal conductivity for HCPCMs to 2.959 W/(m·K) at room temperature and 2.400 W/(m·K) at 200 °C, with an average increase of about 2 times. The cost of the prepared HCPCMs experienced a significant reduction of 81.3%, demonstrating favorable economic performance and promising prospects for application. The research findings presented in this article can offer significant insights into the efficient utilization of solid waste.

Microencapsulation of Al-Si-Fe alloys for high-temperature thermal storage with excellent thermal cycling performance

Metal-based phase change heat storage materials have become a potent candidate to regulate supply and demand of thermal energy due to their high conductivity, latent heat and stability. With the development of high-efficiency energy storage systems, materials with higher phase change temperatures are in demand urgently for more effective energy storage, which had not been achieved. Herein, the industrial Al-Si-Fe alloy with phase change temperature of 869 °C was chosen as heat storage material in this research. Furthermore, to prevent the alloy from the inherent problems such as liquid leakage, oxidation and corrosion at high temperature, a new and simple strategy was developed to micro-capsulate the alloy. The prepared process of microcapsules involved two steps: pre-coated of aluminum hydroxide along with hydrothermal carbon and heat treatment in nitrogen atmosphere. The composition, morphology, and thermal performance of the microcapsules were characterized by XRD, SEM, TEM, and TG-DSC. The results indicated the shell below 1 μm was composed of α-Al2O3 strengthened by network AlN fibers formed through the V-S mechanism. The latent heat of microcapsules reached 187.6 J·g−1 which was 82.9 % relative to raw material. Moreover, the total latent heat of the microcapsules did not change much after 300 cycles between 500 and 900 °C, although the phase transition behavior was altered. Overall, this research provides a novel idea for the encapsulation technology and the application of thermal energy storage materials from preparation and structure, which is conducive to promote the application of high-temperature phase change materials.

Characterization of novel lamellar porous Ti3SiC2 as shape-stabilized high-temperature phase change materials composites for durable enhancement thermal storage properties

In pursuit of leveraging porous media for high-temperature phase change materials (PCMs) to enhance the overall thermal conductivity and encapsulation performance of PCMs, this study delves into the corrosion behavior of Ti3SiC2 with a lamellar porous structure in different corrosive environments at both high and low temperatures. By manipulating the solid content to modify the porous structure, the investigation probes the corrosion phenomena and anti-corrosion mechanisms across various porous configurations. The results reveal that F ions exert the most extensive structural degradation on Ti3SiC2. Based on these insights, a successful fabrication of a molten salt phase change composite material, Ti3SiC2/KCl-NaCl, boasting a lamellar structure was achieved. With an increase in solid content, the thermal conductivity escalates from 6.13 to 9.27 W/(m∙K), tripling the heat conductivity of pure KCl-NaCl. However, this also leads to a reduction in latent heat from 126.7 J/g to 46.2 J/g. Consequently, the phase change energy storage performance of PCM prepared by sample 2 emerges as exceptionally commendable. Following 200 thermal cycles on the composite PCM, no discernible structural damage was observed, albeit a slight performance decline. Hence, the lamellar Ti3SiC2/KCl-NaCl structure not only boasts favorable phase change energy storage capabilities but also demonstrates an extended service life.

High-entropy Ti-Zr-Hf-Ni-Cu alloys as solid-solid phase change materials for high-temperature thermal energy storage

High-performance high-temperature solid-solid phase change materials (SS-PCMs) are urgently demanded for thermal energy storage and thermal management at elevated temperatures in the rapidly developing energy and information industries. Here, we report a novel class of Ti-Zr-Hf-Ni-Cu high-entropy alloys showing high thermal-energy-storage performance at elevated temperatures, which are a robust candidate for high-temperature SS-PCMs. Notably, the figure-of-merit values of these Ti-Zr-Hf-Ni-Cu SS-PCMs are an order of magnitude higher than that of traditional SS-PCMs, due to their much higher thermal conductivity and satisfactory volumetric energy storage capacity as compared to traditional SS-PCMs. Furthermore, the phase transition temperatures of these SS-PCMs can be easily and precisely tuned by composition change, in a wide high-temperature range of 300–470 °C. These high figure-of-merit SS-PCMs with high thermal conductivity have extremely promising prospects for advanced thermal energy storage and compact high-power-density electronic cooling applications. This work opens a new field for exploring high-entropy alloys as solid-solid thermal-energy-storage phase change materials.

A Dual Encapsulation Strategy for High-Temperature Micro PCM Particles with High Cyclic Durability.

Addressing critical issues such as high-temperature corrosion, leakage, degradation, and subpar cyclic performance is imperative for phase change materials (PCMs), prompting the development of appropriate encapsulation techniques to surmount these challenges. In this study, a dual encapsulation strategy is proposed for high-temperature micro PCM particles. Al-Si core is microencapsulated via the "solvent evaporation-heating curing" method. Subsequently, TiO2 is employed as the skeleton material for form-stable encapsulation of PCM microcapsules by "cold pressed sintering". Detailed analysis of the crystalline phase transformation mechanism in the sintering synthesis pathway of TiO2 underscore its potential as a robust structural material with exceptional thermal stability. Furthermore, the incorporation of hexagonal boron nitride (hBN) results in a substantial enhancement of the thermal conductivity of the composites, increasing by 121.1-131.3%. The prepared form-stable phase change microcapsules (FSPCMs) are subjected to 5000 thermal cycles in the air atmosphere. There is no observed PCM leakage or composite ruptures in the FSPCM. Moreover, the oxidized mass gain is merely 3.3%, signifying exceptional oxidation resistance. Thermophysical analysis indicates that FSPCM can retain 91.3% of the enthalpy after 2000 cycles, with over 80% preservation after 5000 cycles, underscoring its remarkable cyclic thermal durability.

Performance investigation and optimization of latent heat exchanger with pin fins based on non-uniform deployment strategy

Latent heat storage technology is an essential way of efficiently utilizing industrial residual heat, which helps to the objective of carbon neutrality in all countries. In this work, latent heat exchangers with pin fins are numerically investigated based on non-uniform deployment strategy and then optimized according to response surface method. The influences of rotation angle, non-uniform fin pitch, non-uniform fin length and combination of phase change materials with different melting temperatures on thermal storage performance are studied. Results show that the increment of rotation angle facilitates the reduction of complete melting time, and the optimal angle accelerates the melting speed by 10.3% compared to the 0° angle. The arrangements of gradually decreasing fin pitch and gradually increasing fin length along flow direction of heat transfer fluid improve the heat storage performance, which can reduce the complete melting time by 7.3% and 22.2% respectively, compared to the uniform arrangement. The multiple phase change materials latent heat exchanger with high melting temperature phase change material placed in high temperature region and low melting temperature phase change material in low temperature region can make better utilization of heat from heat transfer fluid, which can improve the melting speed by 16.8% compared with the single phase change material latent heat exchanger. The optimized latent heat exchanger based on response surface method reduces the complete melting time by 23.4% compared to the original model. In conclusion, the heat storage performance of latent heat exchanger with pin fins effectively improved by adopting the non-uniform deployment strategy.

Experimental analysis of a power-to-heat storage with high-temperature phase change materials to increase flexibility and sector coupling

To boost the flexibility, sector coupling and manageability of renewable energy systems, a unique power-to-heat storage (electric charging, thermal discharging) is proposed. The hybrid thermal energy storage system, including phase change materials, is built using flat pillow-plates and heating rods. Experimental testing is conducted to assess the prototype's electrical and thermal performance. In addition, a parametric study involving several charging and discharging control strategies is proposed in this context.The suggested hybrid thermal storage system provides a total storage capacity of 4.87kWh using nitrate salts as phase-change material (eutectic mixture of KNO3 and NaNO3). The charging efficiency ranges from 65 to 90%, depending on the charging/discharging strategy, and the discharging period can be shortened by more than 1 h. Additionally, active management of the heating rod temperature reduces the charging period by half, making the storage system highly flexible. This demonstrates the ability of this system to aid in modularity and flexibility for effective energy management in the context of renewable energy and industry thanks to an increased storage capacity.

Soft-hard complex microsphere strategy to construct high-temperature form-stable phase change material for melt-spun temperature-regulating fibers

Phase change materials (PCMs) have excellent temperature regulation ability and are usually used in smart wearable devices. However, PCMs prepared by traditional methods cannot be applied to high-temperature (>230 °C) melt spinning, and leakage of PCM is prone to occur during spinning. This work successfully prepared a series of PCMs with high thermal form-stable by the strategy of capillary adsorption of inorganic porous materials and surface microchemical crosslinking and proved that it can effectively solve the above-mentioned problems of high-temperature melt-spinning temperature regulating fibers. This PCM prepared by combining porous SiO2 adsorption and chemical crosslinking of polyethylene glycol derivatives exhibits excellent heat resistance at 130 °C for 40 min. In addition, polycaprolactam (PA6) was selected as the polymer matrix, and PA6-based temperature regulating fibers with excellent temperature regulating functions were prepared. The thermal response time of the fabric prepared from this fiber in the hot environment is 782 s, and the maximum temperature difference is 5.4 °C. Moreover, the exothermic duration in cold environment is 427 s, and the maximum temperature difference is 2.3 °C. This shows that the prepared temperature regulating fiber has good application prospect in heat-regulating devices.

Thermal analysis of phase change materials storage in solar concenter

Thermal analysis of high-temperature phase change materials (PCM) is conducted with the consideration of a 20% void and buoyancy-driven convection in a stainless-steel capsule. The effects of the thermal expansion and the volume expansion due to phase change on the energy storage and retrieval process are explored. The used water to fill the void between two different wax paraffin and stearic acid spheres is considered as a potential PCM for concentrated solar power. The charging/discharging process into and from the capsule wall is simulated under different boundary conditions for laminar and turbulent flows. Computational models are conducted by applying an enthalpy-porosity method and volume of fluid method to calculate the transport phenomena within the PCM capsule, including an internal air void. A simplified two-dimensional model of the PCM contained within the spheres is constructed and thermal analyses are performed for the transition from solid to liquid states. Simulated charging process modes are compared with the theory. According to experiments, the temperature distributions from 40-60 mm without and with 60 mm with copper fin have different behavior. The paraffin takes less time than stearic acid for total transformation at a rate of 0.5. The size of the sphere increases over the amount of time and the phase of the sphere to complete changes as stearic acid expands more than paraffin during the transition. Inserting a rectangular fin, that is made from copper into the ball reduces the cycle time and increases output.

Graphite crucible interaction with Fe–Si–B phase change material in pilot-scale experiments

Abstract Fe–26Si–9B alloy is a promising high temperature phase change material (HTPCM), due to its high heat of fusion, small volumetric change, abundance, and low cost. Additionally, graphite has been identified as a promising candidate for use as a container material for this alloy. In this study, the feasibility of using graphite for Fe–26Si–9B HTPCM is investigated in a pilot-scale. Specifically, 4–5 kg Fe–26Si–9B master alloys were melted in graphite crucibles using an induction furnace, which underwent 2–3 thermal cycles in the temperature range of 1,100–1,375°C. The results showed that SiC and B4C precipitates were formed in the alloys. However, these carbides were found to be present only on the surface of the solidified alloys and not in the main body. Still, the chemical composition of the Fe–26Si–9B alloy remained relatively stable during the thermal cycles. It was also seen that the graphite crucible withstood the temperature cycles without cracking. Therefore, the use of graphite as a container for Fe–26Si–9B phase change material is a promising approach.

Near zero thermal performance loss of Al-Si microcapsules with fibers network embedded Al2O3/AlN shell

Al-Si alloy, a high temperature phase change material, has great potential in thermal management due to its advantages of high heat storage density and thermal conductivity. Microencapsulation of Al-Si alloy is one of the effective techniques to solve high temperature leakage and corrosion. In this paper, commercial Al-10Si alloy micro powders were encapsulated with flexible ceramic shells whose total thickness is below 1 µm by hydrothermal treatment and heat treatment in N2 atmosphere. The compositions and microstructures were characterized by XRD, SEM and TEM. The shell was composed of AlN fibers network structure embedded with α-Al2O3/AlN which prevented the alloy from leaking and oxidizing, as well as had excellent thermal stability. The latent heat of microcapsules was 351.8 J g–1 for absorption and 372.7 J g–1 for exothermic. The microcapsules showed near zero thermal performance loss with latent heat storage (LHS)/ release (LHR) was 353.2/ 403.7 J g–1 after 3000 cycles. Compared with the published Al-Si alloy microcapsules, both high heat storage density and super thermal cycle stability were achieved, showing promising development prospects in high temperature thermal management.

A Brief Review and Its Incorporation with Bibliometric Analysis of Phase Change Materials for Thermal Energy Storage

Reduction of Food Losses and Wastes (FLW) through the use of cold chain is one strategy applied in accelerating the SDGs goals of zero hunger. The application of Thermal Energy Storage (TES) based on PCM (Phase Change Material) is considered as one of best efforts for the simultaneous reduction of food losses and wastes, reduction of energy consumption as well as preserve the right temperature for food product. This paper presents the review of phase change material for thermal energy purposes and its bibliometric analysis. Bibliometric analysis on term of cold chain logistics show that there is correlation between cold chain and terms of optimization, vehicle routing, carbon emission, refrigeration, and phase change materials. The definition of TES and PCM, as well as the advantages of TES based on latent material are described in this paper. PCMs is classified into solid-solid, solid-liquid, solid-gas and liquid-gas based on its phase. The potential generation of gas and larger volume on solid-gas and liquid-gas PCMs limits the application of those two types of PCMs. PCMs is also classified according to the phase change temperature in which low, medium and high temperature PCMs. Organic, inorganic and composite based PCMs are the classification of PCMs based on the chemical composition. Among the types of PCMs, this paper present a deep review of paraffin based organic PCMs. The appearance of term of thermal conductivity in bibliometric analysis on term of organic phase change materials is due to organic PCMs commonly have low thermal conductivity

Performance optimization for a novel two-stage thermoelectric generator with different PCMs embedding modes

In this study, a novel two-stage TEG with different phase change materials (PCMs) embedding modes is proposed to improve the efficiency of TEG systems. The output power and electrical energy of single-stage and two-stage TEG combined with different PCMs is firstly compared at the limit of total length of the PCM containers. Furthermore, the effect of different PCMs embedding modes, including arranged at the heat source side, between two TEGs and heat sink side, on the performance of two-stage TEG system was discussed. Finally, the amount of different PCMs arranged at different locations was optimized. The results showed that although application of high temperature PCM on the heat source side can alleviate the effect of heat source fluctuations to provide more stabilized output power, the total electrical energy is seriously reduced in the two-stage TEG system. Compared with the single-stage TEG system, the two-stage TEG system provides a much higher output power and electrical energy, in which the harvested total electrical energy of the optimum two-stage TEG system is increased by 44.8% with a conversion efficiency of 6.9%. These results are of great significance to the design of advanced TEG system for waste heat recovery.

Controllable preparation and thermal properties of SiC spherical high temperature shape-stable composite phase change materials based on gel-casting

The development of high-temperature composite phase change materials (CPCMs) suitable for mass-production and high-performance is still a very urgent problem in the efficient utilization of renewable energy. In this study, a SiC spherical high-temperature CPCMs based on aqueous gel-casting suitable for batch molding using commercially available silicone molds is proposed. The porosity of the porous SiC framework can be adjusted by changing the content of starch granules in the slurry. The sample containing 20 wt% starch has relatively high open porosity and thermal conductivity, which is considered to be close to the optimal formulation of CPCMs. This formula possesses a high thermal conductivity of 10.2 W·m−1·k−1 benefiting from the continuous thermal transport channels consisting of the uniformly distributed large spherical pores and interconnected small pores. Meanwhile, the thermal storage density of the CPCMs reaches 395.21 J·g−1 in the temperature range of 550 ℃ and 750 ℃ since up to 89.06% of the pores are filled with molten salts. At the same time, the CPCMs exhibit excellent cycle stability in 100 thermal cycles. In particular, these CPCMs can be easily integrated into thermal energy storage (TES) system. Based on the rapid heat storage simulation of the C-D model, the packed-bed latent thermal energy storage system containing spherical CPCMs will have a more uniform temperature distribution and a 26.7% reduction in charging time compared with the traditional packed-bed system. This work provides a new reference for the design of spherical CPCMs in TES systems.

Application and analysis of flip mechanism in the melting process of a triplex-tube latent heat energy storage unit

In order to improve the characteristics of uneven melting in the melting process of the horizontal latent heat energy storage system, the triplex-tube latent heat energy storage unit is taken as the research object, and the flip mechanism is applied to its melting process. Numerical simulation is used for the research, and the numerical model is verified by experimental data. The results show that under different dimensionless times, the melting performance of the unit can be significantly improved by a single flip. When the dimensionless time is 0.4576, it is found that the total melting time of the unit is reduced by 16.17 %, the average heat absorption rate is increased by 14.7 %, but the total heat energy absorption is reduced by 3.85 %. The results show that the addition of a flip can effectively shorten the melting time and increase the heat absorption rate, but it has a negative effect on the total heat absorption in one melting cycle. Moreover, through the comparison of dynamic flow rate, dynamic temperature response, and temperature interval, it is shown that the addition of flip effectively reduces the negative influence of the hard-to-melt zone on the melting performance of the unit during the melting process. The flip mechanism reduces the proportion of high-temperature phase change material in the melting process and makes the melting process more uniform.

Analysis on the thermal behaviour of the latent heat storage system using S-CO2 and H-PCM

Energy storage and utilization of CO2 have attracted increasing attention due to international zero carbon plan. Here, the latent heat storage system using high-temperature phase change material (H-PCM) and supercritical CO2 (S-CO2) is analysed by using CFD simulation, in which the tube containing S-CO2 is submerged in a tank containing the salt with high melting temperature. A new and combined phase transition model is developed to describe the dynamics of PCM in different phase state, and it is validated against experimental data in literature. The dynamics of natural convection is focused, and its effects on the heat storage system are analysed, including maximum natural convection velocity, phase interface, and melting pattern. The results show that natural convection has a great influence on the melting process of the H-PCM in the charging process. The melting pattern of H-PCM could be contrary between the cases with and without considering natural convection. During the discharging process, natural convection has little effect on the heat transfer of energy release due to its short duration. With the increase of ratio between the S-CO2 tube and H-PCM tank, the strength of the natural convection of melting H-PCM is enhanced, especially the duration of natural convection.

Thermal characteristics of melting of a phase change material enhanced by a stainless-steel 304 periodic structure

In this work, melting of a high-temperature inorganic phase change material (PCM) eutectic (with a melting point of 569 °C) within a vertical cylindrical tank has been experimentally investigated. To promote the heat transfer rate, a periodic structure that is constructed by a commercial SS-304 mesh screen has been considered and immersed into the PCM tank. Thermal characteristics of the PCM-periodic structure tank under different initial temperatures (450, 490 and 546 °C) and wall temperatures (620, 640, 660, 680 and 700 °C), are then investigated and reported. The presented experimental data can facilitate practical engineers to find the best operating condition of similar PCM tanks; meanwhile, it can also be employed for the investigation of thermal response of transient heat conduction before melting starts.

Discharge performance of a high temperature phase change material with low-cost wire mesh

Thermal energy storage is increasingly needed in a sustainable world because of its potential of capturing waste heat and being incorporated in solar power plants. For power generation, in particular, as turbine technology advances, a demand for higher temperature thermal energy storage materials also grows. For this purpose, latent thermal energy storage fits in well since it uses phase change materials (PCMs) which generally have a higher energy density compared to their sensible heat counterparts. In the present study, a eutectic Na2CO3(41.69%)-(33.1%)KCl-(25.21%)NaCl phase change material (PCM) with a melting temperature of 569 ° C was chosen as the storage material to experimentally assess the performance benefit of using a readily available stainless steel (ss304) wire mesh (as the periodic structure) to enhance heat transfer within the domain. In addition, for discharging, a numerical model was developed and compared with the experimental results. Furthermore, for discharging, a numerical investigation of the influence of the heat transfer fluid (HTF) flow-rate to the rate of heat transfer was performed. Overall, it was experimentally observed that the charging time for the composite case was shortened by about 35%, compared to the pure PCM case. For discharging, in the axial direction, the composite solidification time when compared to the pure PCM case was on average 10% shorter. Regarding the radial discharging performance of the composite, there was only about 5% improvement compared to the pure PCM case, which was expected due to the thermal contact resistance in the radial direction. Discharging experimental results were used to validate a discharging numerical model. Discharging results from the model showed that increasing the flow rate of the heat transfer fluid (HTF) reduced the time for solidification. It was observed that for the HTF flow rate of 5 L/min, 10 L/min, 20 L/min and 30 L/min, the discharge time was shortened by 23%, 30%, 33% and 35%, respectively.

Development of over 3000 cycles durable macro-encapsulated aluminum with cavity by a sacrificial layer method for high temperature latent heat storage

The high-temperature metallic phase change materials (PCMs) are attracting great attentions as alternatives to sensible heat storage materials in thermal energy storage (TES) systems. However, the high corrosivity, easy leakage and oxidation phenomena of metallic PCMs have limited their applications. This work reports a facile and novel sacrificial layer method with the purpose to create macro-encapsulating aluminum (Al) PCM by alumina (Al2O3) shell characterized by a ‘buffer’ inner cavity. The inner cavity could offer buffer space to accommodate the huge thermal volume expansion of Al core PCM during heating and melting, thereby preventing the breakage of the capsules and ensuring the long-term stability. A series of Al balls with diameters of 4–25 mm were firstly coated with paraffin sacrificial layer then by Al2O3 dough shell, which was finally conducted by the two-step heat treatment, in which a low-temperature stage aimed at removing the paraffin layer while the high-temperature stage aimed at the capsule sintering formation. The final macrocapsules with diameters of 6.5–31.5 mm were obtained, in which the capsules with Al core balls larger than 15 mm showed superior gravimetric and volumetric heat storage density because of their high core–shell ratio. For example, the 25 mm@0.75 mm@2.5 mm macrocapsules could present high heat storage density of 348 kJ/kg and 902 J/cm3 at the temperature range of 600–700 °C. The macrocapsules also showed a long-time thermal cycling stability, since that no damage or leakage was observed over 3000 times of melting and solidification under air atmosphere, indicating that they can be used over 8 years without any degradation of thermophysical properties. This demonstrates the potential application of the Al2O3 encapsulated Al macrocapsules with inner cavity in high-temperature TES systems.

Techno-economic and exergo-economic evaluation of a novel solar integrated waste-to-energy power plant

The content of municipal solid waste generation is increasing due to the industrial and population growth. Energy generation from municipal solid waste is one of the efficient and promising method to dispose waste in a sustainable manner, while reducing the fossil fuel energy limitations. However, conventional waste-to-energy plants have less thermal efficiency due to the higher moisture content that lowers its heating value. The solar thermal integration is one of the proposed solutions to enhance the steam inlet temperature in the power generation system that will further increase the plant performance. In this study, an innovative solar integrated municipal solid waste incineration plant is proposed to advance the waste-to-energy and concentrated solar power thermal energy technologies. The system integration is carried out utilizing the useful solar heat harvested in the heliostat tower receiver system by transferring heat to the working steam of the incineration plant in the heat exchanger and enhance the turbine inlet temperature and the system’s performance considerably. Based on 300 t/d incineration facility, proposed system is investigated exergo-economically by varying certain influential parameters using engineering equation solver and performance has been compared with the conventional reference plant. The system is integrated with high-temperature Phase Change Materials, which able to store thermal energy enough for the light-time system operation. The results attribute that the network output of the proposed integrated facility has substantial improved (almost 12.61 %) but with the penalty of increase in the exergy destruction cost rate. In addition, levelized cost of electricity of the proposed plant is 13.9 % less than the conventional one and it decreases with the rise of steam temperature. Energy efficiency of the proposed plant improves to approximately 36.34 % as direct normal irradiation increases from 650 W/m2 to 900 W/m2. In addition, Incineration boiler is the major source of exergy destruction (almost 50 %) with 175.2 $/hr exergy destruction cost.