High-temperature Liquid Chromatography Research Articles

Recent developments in the HPLC separation of phenolic compounds

Phenolic compounds represent a class of highly complex naturally occurring molecules that possess a range of beneficial health properties. As a result, considerable attention has been devoted to the analysis of phenolics in a variety of samples. HPLC is the workhorse method for phenolic separation. However, conventional HPLC methods provide insufficient resolving power when faced with the complexity of real-world phenolic fractions. This limitation has been traditionally circumvented by extensive sample fractionation, multiple analysis methods and/or selective detection strategies. On the other hand, there is an increasing demand for improved throughput and resolving power from the chromatographic methods used for phenolic analyses. Fortunately, during the last decade, a number of important technological advances in LC have demonstrated significant gains in terms of both speed and resolution. These include ultra high-pressure liquid chromatography (UHPLC), high-temperature liquid chromatography (HTLC), multi-dimensional separations as well as various new stationary phase chemistries and morphologies. In recent years, these technologies have also found increasing application for phenolic analysis. This review seeks to provide an updated overview of the application of recent advances in HPLC to phenolic separation, with the emphasis on how these methodologies can contribute to improve performance in HPLC analysis of phenolics.

General Strategy for Performing Temperature Programming in High Performance Liquid Chromatography: Prediction of Linear Temperature Gradients

This paper describes how an empirical retention model is transferred from temperature-programmed gas chromatography (GC) to high temperature liquid chromatography (HT-HPLC). In order to evaluate the retention prediction, a temperature range from 50 to 180 °C was investigated using two test mixtures consisting of steroids and polycyclic aromatic hydrocarbons. In this temperature range, heating rates from 1.5 °C min(-1) up to 30 °C min(-1) were applied using four different high temperature stable HPLC columns with inner diameters of 1.0, 2.1, 3.0, and 4.6 mm. Temperature lag phenomena in the HPLC column as well as in the column oven are discussed, and it is shown that the linear elution strength (LES) model can be applied without any mathematical extension in order to take a temperature-dependent delay time into account. On the basis of this approximation, it is possible to perform a systematic method development using linear temperature gradients in liquid chromatography. Furthermore, it is shown that only two initial temperature gradient runs are necessary to predict the retention times of the analytes with a maximal relative error of less than 2%.

Kinetic behaviour in supercritical fluid chromatography with modified mobile phase for 5 μm particle size and varied flow rates

After much development of stationary phase chemistry, in recent years the focus of many studies in HPLC has shifted to increase the efficiency and analysis speed. Ultra high pressure liquid chromatography (UHPLC) using sub-2 μm particles, and high temperature liquid chromatography (HTLC), using temperatures above 100 °C have received much attention. These new approaches allow the use of flow rates higher than those classically used in HPLC, reducing the analysis duration. Due to the low viscosity of supercritical fluids, high velocities, i.e. high flow rates, can be achieved with classical pumping systems typically used in supercritical fluid chromatography (SFC). The effects of the flow rate increase with CO 2/methanol mobile phase was studied on the inlet pressure, t 0, the retention factor of the compounds, and on the efficiency. Simple comparisons of efficiencies obtained at varied temperature between SFC and HPLC, with a packed column containing 5 μm particles, show the greater kinetic performances achieved with the CO 2/methanol fluid, and underline specific behaviours of SFC, occurring for high flow rates and sub-ambient temperature. Some values ( N/ t 0) are also compared to UHPLC data, showing that good performance can be achieved in SFC without applying drastic analytical conditions. Finally, simple kinetic plots ( t 0 vs N) at constant column length are used to select combinations of temperature and flow rate necessary to achieve a required theoretical plate number.

Characterization of polyolefins by comprehensive high-temperature two-dimensional liquid chromatography (HT 2D-LC)

Temperature rising elution fractionation hyphenated to size exclusion chromatography (TREF×SEC) is a routine technique to determine the chemical heterogeneity of semicrystalline olefin copolymers. A serious limitation is its applicability to non crystallizing samples. Comprehensive high temperature two-dimensional liquid chromatography (HT 2D-LC) gives an alternative to characterize the chemical heterogeneity of copolymers irrespective of their crystallizability. We have hyphenated interactive HPLC, which separates polyolefins according to their chemical composition, with high-temperature size exclusion chromatography (SEC), which distinguishes polyolefins with regard to their molar mass at 160°C. The first separation step was based on a selective adsorption of macromolecules on a Hypercarb® column packed with porous graphite particles and subsequent desorption by a gradient 1-decanol→1,2,4-trichlorobenzene at 160°C. The SEC column was calibrated with polypropylene (PP) and polyethylene (PE) standards and it turned out that the injection solvent from the first dimension influenced the elution of PP in the SEC column, while the retention of PE was virtually constant. HT 2D-LC was then used to separate a broad variety of polyolefin blends containing PE, PP with different microstructure, ethylene–propylene (EP) and ethylene–propylene–diene (EP(D)M) rubber and ethylene/1-hexene copolymers. For the first time it has been shown that the elution of iPP in the gradient HPLC is molar mass dependent. The results from the HT 2D-LC separation were compared to those from TREF×SEC-experiments. The particular advantage of HT 2D-LC over TREF×SEC is the fact that HT 2D-LC is also applicable to non crystallizing polyolefin samples. The new technique therefore resolves the problem to analyze the chemical heterogeneity of non crystallizing olefin copolymers like EP and EP(D)M copolymers.

Chromatography with Higher Pressure, Smaller Particles and Higher Temperature: A Bioanalytical Perspective

Recent years have seen widespread use of ultra-high-pressure liquid chromatography (UHPLC) in biological fluids. Most commonly the emphasis is on developing high throughput assay methods to reduce the analysis time and cost. Particle size and temperature are chromatographic parameters that can be changed to improve efficiency and obtain rapid separations. UHPLC and high-temperature liquid chromatography (HTLC) are two techniques that reduce the analysis time by decreasing the size of the column packing material and increasing the column temperature, respectively. Both of these techniques have advantages and limitations. In this article we have summarized the history, theoretical background of UHPLC and HTLC and the various advantages and limitations of sample preparation techniques and the detection systems (mass spectrometry and ultraviolet) used for the bioanalytical assays. In addition, selected bioanalytical applications of the two techniques have been reviewed and tabulated.

Separation of short-chain branched polyolefins by high-temperature gradient adsorption liquid chromatography

A new separation principle was recently introduced into the analytical characterization of polyolefins by researchers from the German Institute for Polymers in Darmstadt. It was demonstrated that polyolefins can be selectively separated via high-performance liquid chromatography on the basis of their adsorption/desorption behaviours at temperatures as high as 160 °C. A Hypercarb® column packed with porous graphite gave the best results. The mobile phase consisted of a mixture of 1-decanol and 1,2,4-trichlorobenzene. In this work, the same chromatographic system is applied to the separation of ethylene/alkene and ethylene/norbornene copolymers. It was found that the elution volumes of the samples correlate linearly with the average chemical composition of samples. The elution volume is indirectly proportional to the concentration of branches in the ethylene/alkene copolymer. Branching shortens the length of continuous methylene sequences of the polymer backbone, thus decreasing the probability of orientation of a methylene sequence in a flat conformation on the graphite surface, which enables the most intensive van der Waals interactions between the methylene backbone and the carbon surface. An opposite trend in the elution order has been found for ethylene/norbornene copolymers. The elution volume of the ethylene/norbornene copolymers increased with the concentration of norbornene. It indicates pronounced attractive interactions between graphite and the cyclic comonomer.

A study of some practical aspects of high temperature liquid chromatography in pharmaceutical applications

In the pharmaceutical industry fast and efficient separation techniques play an increasing role among analytical methods because the samples to be investigated grow both in complexity and number, and there is an increasing time pressure to complete the analysis. Reducing the analysis time without decreasing the efficiency is possible using higher pressures, elevated temperatures, smaller particle sizes, or a combination of these approaches. Recently developed chromatographic techniques such as the UHPLC (ultra high performance liquid chromatography) and HTLC (high temperature liquid chromatography) are highly promising in meeting these demands. In this study, high temperature liquid chromatography (HTLC) with a zirconia-based column and temperatures elevated up to 150 °C was used. We investigated the chromatographic behaviour of a steroid active pharmaceutical ingredient (levonorgestrel) and its structurally related impurities as model compounds. The effect of the temperature in the range of 50–150 °C and the flow-rate in the range of 0.5–3.0 ml/min, and using methanol as an organic modifier, were studied for optimisation of the separation method.

High-temperature two-dimensional liquid chromatography of ethylene-vinylacetate copolymers

Temperature rising elution fractionation hyphenated to size exclusion chromatography (TREF × SEC) is a routine technique to determine the chemical heterogeneity of semicrystalline olefin copolymers. Its applicability is limited to well crystallizing samples. High-temperature two-dimensional liquid chromatography, HT 2D-LC, where the chromatographic separation by HPLC is hyphenated to SEC (HPLC × SEC) holds the promise to separate such materials irrespective of their crystallizability. A model blend consisting of ethylene-vinyl acetate (EVA) copolymers covering a broad range of chemical composition distribution including amorphous and semicrystalline copolymers and a polyethylene standard was separated by HT 2D-LC at 140 °C. Both axes of the contour plot, i.e. the compositional axis from the HPLC and the molar mass axis from the SEC separation were calibrated for the first time. Therefore, a new approach to determine the void and dwell volume of the developed HT 2D-LC instrument was applied. The results from the HT 2D-LC separation are compared to those from a cross-fractionation (TREF × SEC) experiment.

High-Temperature Liquid Chromatography Inductively Coupled Plasma Atomic Emission Spectrometry hyphenation for the combined organic and inorganic analysis of foodstuffs

The coupling of a High-Temperature Liquid Chromatography system (HTLC) with an Inductively Coupled Plasma Atomic Emission Spectrometer (ICP-AES) is reported for the first time. This hyphenation combines the separation efficiency of HTLC with the detection power of a simultaneous ICP-AES system and allows the combined determination of organic compound and metals. The effluents of the column were introduced into the spectrometer and the chromatograms for organic compounds were obtained by plotting the carbon emission signal at a characteristic wavelength versus time. As regards metals, they were determined by injecting a small sample volume between the exit of the column and the spectrometer and taking the emission intensity for each one of the elements simultaneously. Provided that in HTLC the effluents emerged at high temperatures, an aerosol was easily generated at the exit of the column. Therefore, the use of a pneumatic nebulizer as a component of a liquid sample introduction system in the ICP-AES could be avoided, thus reducing the peak dispersion and limits of detection by a factor of two. The fact that a hot liquid stream was nebulized made it necessary to use a thermostated spray chamber so as to avoid the plasma cooling as a cause of the excessive mass of solvent delivered to it. Due to the similarity in sample introduction, an Evaporative Light Scattering Detector (ELSD) was taken as a reference. Comparatively speaking, limits of detection were of the same order for both HTLC–ICP-AES and HTLC–ELSD, although the latter provided better results for some compounds (from 10 to 20 mg L −1 and 5–10 mg L −1, respectively). In contrast, the dynamic range for the new hyphenation was about two orders of magnitude wider. More importantly, HTLC–ICP-AES provided information about the content of both organic (glucose, sucrose, maltose and lactose at concentrations from roughly 10 to 400 mg L −1) as well as inorganic (magnesium, calcium, sodium, zinc, potassium and boron at levels included within the 6–3000 mg L −1) species. The new development was applied to the analysis of several food samples such as milk, cream, candy, isotonic beverage and beer. Good correlation was found between the data obtained for the two detectors used ( i.e., ICP-AES and ELSD).

Emerging Analytical Separation Techniques with High Throughput Potential for Pharmaceutical Analysis, Part I: Stationary Phase and Instrumental Developments in LC

In recent years, a trend of change has been observed within pharmaceutical industry. As modern drug discovery has reached a remarkable level of complexity and drugs need to be discovered, developed and produced against strict timelines and within cost- and regulatory constraints, industry seeks "lean" solutions to increase productivity. Among them, increasing the sample throughput of the ever-growing number of necessary (routine) analyses has become a popular target to cut precious time. For the last thirty years, High-Performance Liquid Chromatography (HPLC) has been the leading technology when it comes to various analyses in pharmaceutical industry; however, its necessity of serial analyses taking typically 10-45 min has been a sample throughput-limiting barrier. Lately, the fundamentals of HPLC have been exploited to raise new technologies that can speed up analyses to ground breaking limits, without compromising separation efficiency. This paper reviews some promising technologies, i.e. totally porous sub-2microm particles accompanied by pressures up to 1000 bar (Ultra-Performance Liquid Chromatography or UPLC), fused-core particle technology, monolithic supports and High Temperature Liquid Chromatography (HTLC), having the potential to take LC to the next level in pharmaceutical industry. As each analytical method has its own demands, the advances of the above technologies are discussed for different applications in pharmaceutical analysis where high-throughput analysis can be meaningful, i.e. in a drug discovery and development setting, and in quality operations. Both chemical and biological pharmaceuticals are considered. We discuss the perspectives of these technologies and their realizations up to now in high-throughput pharmaceutical analysis.

Development of Comprehensive Two-Dimensional High Temperature Liquid Chromatography × Gel Permeation Chromatography for Characterization of Polyolefins.

This work documents the development of the title system wherein the first dimension is a separation of polyolefins, according to composition, via an adsorption mechanism on a HYPERCARB stationary p...

High temperature liquid chromatography of intact proteins using organic polymer monoliths and alternative solvent systems

Alternative approaches to conventional acetonitrile gradient methods for reversed-phase liquid chromatographic analysis of intact proteins have been investigated using commercial poly(styrene- co-divinylbenzene) monolithic columns (Dionex ProSwift™ RP-2H and RP-4H). Alternative solvents to acetonitrile (2-propanol and methanol) coupled with elevated temperatures demonstrated complementary approaches to adjusting separation selectivity and reducing organic solvent consumption. Measurements of peak area at increasing isothermal temperature intervals indicated that only minor (<5%) decreases in detectable protein recovery occurred between 40 and 100 °C on the timescale of separation (2–5 min). The reduced viscosity of a 2-propanol/water eluent at elevated temperatures permitted coupling of three columns to increase peak production (peaks/min) by 16.5%. Finally, narrow-bore (1 mm i.d.) columns were found to provide a more suitable avenue to fast, high temperature (up to 140 °C) separations.

Correction to Characterization of Flavor Modulating Effects in Complex Mixtures via High Temperature Liquid Chromatography

Correction to Characterization of Flavor Modulating Effects in Complex Mixtures via High Temperature Liquid Chromatography

Identification of Bisprenylated Benzoic Acid Derivatives from Yerba Santa (Eriodictyon ssp.) Using Sensory-Guided Fractionation

Due to certain off-flavor problems and lacking bitter masking effects with Yerba Santa (Eriodictyon angustifolium and E. californicum) extracts, which are also described as bitter, herbal, medicinal, phenolic, or astringent, methanolic extracts were fractionated and evaluated for their taste properties using a high temperature liquid chromatography (HTLC)-based approach. The taste-guided fractionation led to the identification of a series of novel bisprenylated benzoic acids (erionic acids A (1), B (2), C (3), D (4), E (5), and F (6) and eriolic acids A (7), B (8), C (9), and D (10), respectively), along with the known flavonoids eriodictyol, homoeriodictyol, hesperetin, and chrysoeriol. The new compounds were isolated in larger amounts for characterization from Narrow Leaf Yerba Santa (E. angustifolium) and California Yerba Santa (E. californicum), respectively, using fast centrifugal partition chromatography (FCPC) and HTLC. The structures were elucidated using one and two-dimensional NMR spectroscopy and high resolution mass spectrometry (HR-MS). For E. californicum, data regarding seasonal and climatic variation of the eriolic acid contents and of the flavonoids were collected. The flavor properties of some of the isolated new compounds were evaluated; they showed strong off-flavor characteristics, such as bitter, astringent, phenolic, or woody, and may contribute to the sensory effects observed for crude Yerba Santa extracts. Erionic acid C (3) was not only able to increase the absolute bitterness but also to extinguish the bitter masking effect of homoeriodictyol in a caffeine solution.

Possibilidades e limitações no uso da temperatura em cromatografia líquida de fase reversa

High-temperature liquid chromatography (HTLC) is a technique that presents a series of advantages in liquid phase separations, such as: reduced analysis time, reduced pressure drop, reduced asymmetry factors, modified retentions, controlled selectivities, better efficiencies and improved detectivities, as well as permitting green chromatography. The practical limitations that relate to instrumentation and to stationary phase instability are being resolved and this technique is now ready to be applied for routine determinations.

Characterization of Flavor Modulating Effects in Complex Mixtures via High Temperature Liquid Chromatography

The identification of flavor modulating compounds, for example, bitter masking or sweet enhancing compounds, in complex mixtures such as botanical extracts or food preparations is difficult and time- and work-intensive. To accelerate this process, an improved screening method was developed on the basis of the separation of complex matrixes by the so-called LC Taste setup and subsequent comparative sensory analysis. The eluent containing only water and ethanol was diluted with a basic tastant solution (500 mg L(-1) caffeine and 5% sucrose, respectively) and evaluated by a trained panel by duo comparison tests. This novel method was applied to the known flavor and taste modulating substances homoeriodictyol (1), sterubin (2), hesperetin (3), and lactisol (9) as well as to simple mixtures of homoeriodictyol (1), sterubin (2), and hesperetin (3). To evaluate the potential of the method for more complex matrixes, the protocol was applied to plant extracts from Yerba Santa (Eriodictyon californicum) and honeybush tea (Cyclopia intermedia). The flavor modulating activities reported for homoeriodictyol (1), sterubin (2), and hesperetin (3) could be confirmed in these complex mixtures.

Investigation of porous graphitic carbon at high-temperature liquid chromatography with evaporative light scattering detection for the analysis of the drug combination artesunate—Azithromycin for the treatment of severe malaria

Artesunate combined therapies represent the best option for the treatment of malaria and require the development of new methods of analysis. Retention, selectivity and detection with high-temperature liquid chromatography-porous graphitic carbon-evaporative light scattering detection was studied for artesunate and azithromycin separation. Organic solvent, concentration of organic modifiers, temperature and flow rate were all relevant parameters to optimize this separation. The behaviour of artesunate in the tested conditions appeared close to a neutral compound. In CH 3OH, only azithromycin retention was dramatically altered depending on the [triethylamine]/[formic acid] ratio and on the temperature, whereas in CH 3CN, azithromycin, artesunate, artemisinin and dihydroartemisinin retentions decreased with the temperature increase whatever the organic modifier ratio. The best efficiency was obtained with CH 3CN. 25% variation of the concentration values of the organic modifiers did not significantly influenced the retention. The sensitivity of ELSD increased with the flow rate decrease. Peak area and S/N ratio dramatically decreased with the flow rate increase by 10- and 5-fold for artesunate and azithromycin, respectively. Non-linear calibration curves were obtained for both artesunate and azithromycin.

Use of High-Temperature Liquid Chromatography with Sub-2 µm Particle C18 Columns for the Analysis of Seized Drugs

The use of high-temperature liquid chromatography with sub-2 µm particle C18 columns is described for the analysis of seized drugs. The drug compounds investigated include narcotic analgesics, stimulants, depressants, hallucinogens, and anabolic steroids. Although retention times for 20 solutes of various drug classes decreased with increased temperature (15–95°C) under constant gradient conditions, relative retention times increased, decreased, or remained the same. No significant sample degradation at elevated temperature was observed. The use of rapid gradients at 95°C was well suited for drug screening and the separation of anabolic steroids.

High-temperature liquid chromatography. Part II: Determination of the viscosities of binary solvent mixtures—Implications for liquid chromatographic separations

This paper is the second in a series of consecutive publications, explaining the concept of high temperature liquid chromatography under various important aspects. The second publication deals with the determination of the viscosity of binary solvent mixtures used in reversed phase liquid chromatography in a temperature range between 25 and 250 °C. In literature, only limited data of the temperature dependent viscosities of liquid solvents or binary solvent mixtures can be found. Therefore, the viscosities of the pure solvents as well as the binary mixtures had to be determined experimentally up to 250 °C. The viscosity data were used to estimate the pressure drop in a capillary connecting a high-temperature HPLC system with a mass spectrometer. The solvent perturbation could be avoided by adjusting the diameter of the transfer capillary to the viscosity and vapour pressure of the mobile phase. The viscosity data were also used to show that a significant gain in analysis speed is theoretically feasible. This factor clearly depends on the nature of the solvent system, because for mixtures with a large viscosity maximum at ambient temperature, this effect is most pronounced.

High-temperature liquid chromatography. Part III: Determination of the static permittivities of pure solvents and binary solvent mixtures—Implications for liquid chromatographic separations

This paper is the third in a series of three publications, explaining the concept of high-temperature liquid chromatography under various important aspects. The third publication deals with the determination of the static permittivities of pure solvents and binary solvent mixtures used in reversed-phase liquid chromatography in a temperature range between 25 and 200 °C. Furthermore, a critical comparison is made between the polarity parameter which is generally used to define the elution strength of solvent mixtures and the experimentally determined static permittivities. Also, the necessity for using binary solvent mixtures at elevated temperatures is discussed for efficient method development.