High-speed Measurement Research Articles

Laser induced spark ignition of a gaseous methane–oxygen model rocket combustor

The spatio-temporal evolution of laser induced spark ignition of non-premixed gaseous methane and oxygen is investigated. The reactants are injected into an optically accessible combustion chamber from an oxidizer centered shear-coaxial injector. High-speed schlieren imaging and measurements of laser energy deposited are used to characterize ignition behavior at various spark locations throughout the chamber. A spatial map of ignition probability is generated from tests at multiple axial and radial locations from the point of propellant injection. The rate of pressure rise from successful tests reveals two modes of ignition dependent on the location of the laser-induced breakdown, direct and indirect, based on laser-induced breakdown occurring within reactant jet or in the recirculation region, respectively. Physical processes occurring over multiple timescales throughout the direct ignition method are first discussed. Ignition outcomes associated with the indirect method are determined by the hydrodynamic ejection protruding from the laser spark, the behavior of which is explored in detail using flow statistics extracted from images taken at a single spark location. The spatial–temporal progression of this jet is found to be dependent on deposited laser energy, leading to a relationship between the amount of energy added to the flow and ignition outcome. General bounds for spark location, deposited laser energy, and ejection behavior are identified to predict ignition outcomes. Cases that are an exception from these bounds are investigated in detail to understand the cause of unique behavior. These cases lie within regions of the variable space that are susceptible to stochastic elements of the flow.Novelty and Significance Statement: This work investigates laser induced spark ignition of O2 and CH4 issuing from a shear-coaxial injector in a model rocket combustor. Probability of ignition as a function of deposited energy and spatial location is studied with high-speed schlieren imaging and pressure measurements. Two distinct ignition modes that have previously not been identified, direct and indirect, are dependent on the laser deposition location with respect to the reactant jet. For indirect cases, where laser deposition is at a distance from the reactants, the hydrodynamic jet ejection generated from the breakdown of the plasma plays a critical role on ignition probability. The behavior of the ejection jet is characterized to provide a phenomenological description of the ignition process. The results of this research show the important interaction between chemical, fluid dynamic, and thermodynamic processes and their impact on laser ignition.

High-speed PGC demodulation model and method with subnanometer displacement resolution in a fiber-optic micro-probe laser interferometer

As the key of embedded displacement measurement, a fiber-optic micro-probe laser interferometer (FMI) is of great interest in developing high-end equipment as well as precision metrology. However, conventional phase-generated carrier (PGC) approaches are for low-speed scenes and local error analysis, usually neglecting the global precision analysis and dynamic effect of system parameters under high-speed measurement, thus hindering their broad applications. We present a high-speed PGC demodulation model and method to achieve subnanometer displacement measurement precision in FMI. This model includes a global equivalent resolution analysis and revelation of the demodulation error mechanism. Utilizing this model, the failure issues regarding the PGC demodulation method under high speed and large range are addressed. Furthermore, an ultra-precision PGC demodulation algorithm based on the combination of static and dynamic delay adaptive regulation is proposed to enable high-speed and large-range displacement measurement. In this paper, the proposed model and algorithm are validated through simulation and experimental tests. The results demonstrate a displacement resolution of 0.1 nm with a standard deviation of less than 0.5 nm when measuring at a high velocity of 1.5 m/s—nearly a tenfold increase of the latest study.

Photonic-assisted wideband microwave frequency measurement based on optical heterodyne detection

A photonic-assisted microwave frequency measurement (MFM) method based on optical heterodyne detection is proposed and experimentally demonstrated. In the proposed MFM system, a linearly chirped optical waveform (LCOW) from a three-electrode distributed Bragg reflector laser diode (DBR-LD) and a multi-wavelength signal from a Mach-Zehnder modulator (MZM), where the signal under test (SUT) is modulated on an optical carrier from a distributed feedback laser diode (DFB-LD), are heterodyne detected by the photodetector (PD). A bandpass filter then filters the detected signal, and the envelope is detected by an oscilloscope. Then, frequency-to-time mapping is realized, and the signal frequency is measured. Thanks to the fast tuning rate and large tuning range of the DBR-LD, the proposed MFM system has a high measurement speed and a broad instantaneous measurement bandwidth. In the experimental demonstration, a measurement error below 39.1 MHz is achieved at an instantaneous bandwidth of 20 GHz and a measurement speed of 1.12 GHz/µs. The MFM of a frequency-hopping signal is also experimentally demonstrated. The successful demonstration of the MFM system with a simple structure provides a new optical solution for realizing broadband and fast microwave frequency measurements.

Three-dimensional particle image velocimetry experimental study of transient motion characteristics of different scale vortices in gasoline engine

The paper adopted three-dimensional (3D) Particle Image Velocimetry (PIV) combined with high-speed measurement technology to study the transient motion characteristics of tumble flow induced by small and medium-sized vortices on an optical gasoline engine. Meanwhile, the Proper Orthogonal Decomposition (POD) method was introduced to analyze the evolution of transient vortices, revealing the three-dimensional motion principle of vortices with different spatial scales within the cylinder. The results showed that increasing the engine speed can cause boosted in-plane and out-of-plane velocity, especially for the in-plane velocity. However, the average velocity in the plane was higher than that out of the plane with the difference generally within an order of magnitude. The strong intake jet was the main reason for bringing turbulent kinetic energy in the cylinder. The average kinetic energy and turbulent kinetic energy in the cylinder are both significantly improved at high engine speed. From the results of this experiment, it was revealed that there exists isotropic turbulent pulsation characteristics. Overall, the corresponding flow characteristics of different decomposed modes were different. The first mode section had the lowest average velocity ratio, while the other two had the highest. Due to the dissipation of large vortices into small vortices or the shear action between flow layers, new vortices were generated, leading to the intermittent phenomenon of the motion path of the vortex cluster in the target plane. The average vortex size and velocity circularity corresponding to two varied engine speeds presented a downward trend. The average vortex size was smaller at high engine speed, while the vortex intensity was higher. In addition, increasing the engine speed would decrease the vortex scale but increase the vortex strength. This work provided new fundamental insights into analyzing the characteristics of micro-scaled vortices in turbulent flow, as well as the organization of intake in the gasoline engine.

Air-blast atomization of a liquid film

Air-blast atomizers are extensively used for a variety of purposes. Due to its complexity, the atomization mechanism has not been elucidated. In this study, a mechanistic model is proposed to predict the droplet diameter distribution based on the atomization process of a planar liquid film with co-current gas flows, and its validity is examined by comparing the estimated and measured droplet diameters using high-speed image analysis and laser measurement. As a result, using high-speed imaging, we clarified that the bag film rupture is caused not by the turbulence of the gas flow but by the impact of floating droplets on the liquid film of the expanding bag when the film is thin enough. The average thickness of the liquid film at the bag breakup is of the order of micrometres and varies greatly, resulting in a dispersed distribution of droplet diameters. After the film ruptures, the bag film shrinks towards its transversal and vertical rims due to surface tension, forming large-diameter ligaments. During the contraction process of the bag film, tiny droplets of the order of micrometers are formed at the edge of the perforation. Finally, the remaining ligaments with large diameters fragment into large droplets with submillimetre diameters. The good agreement between the measured and predicted droplet diameter distributions validated the mechanistic model.

Acoustic signatures of single disrupting FSP droplets in a heated oxygen atmosphere

Puffing (weak disruptions) and μ-explosions (strong disruptions) play an important role in the synthesis of nanoparticles via flame spray pyrolysis (FSP), as they increase the mass transport of the liquid precursor-solvent system into the gas phase, thus contributing to the formation of homogeneous nanoparticles. Therefore, the targeted experimental study of droplet breakup using single droplet experiments is an essential step in gaining fundamental knowledge about time- and concentration-dependent mechanisms of these disruptions. Here, we study the disruptive combustion of single droplets containing a commonly applied Tin-based precursor with initial Sn molar concentrations ranging from 0.05 mol L−1 to 1 mol L−1. High-speed imaging techniques have been combined with high sample-rate acoustic measurements to detect, distinguish, and quantify droplet disruption phenomena. It has been demonstrated that precursor concentrations up to 0.25 mol L−1 are more prone to μ-explosions, whereas higher Sn molar concentrations show puffing. This shift in the disruption modes between different precursor concentrations is characterized by a boundary that is acoustically identified by quantifying the strength of a disruption using a disruption strength index. Droplet sizes at the instant of the breakup are suggested to play a central role in causing the different droplet breakup characteristics. While the initial droplet sizes of the different precursor solutions are almost identical, they vary at the instant of disruption, resulting in distinct breakup characteristics. Thus, puffing is detected at the instant of disruption for droplet sizes above 55 μm, whereas μ-explosions occur for smaller droplets. Using high-speed measurements to investigate a fixed precursor concentration with two different initial droplet sizes confirms instantaneous droplet-size-dependent effects on the disruption mode.

High-speed and high-precision measurement of biaxial in-plane displacements: tens of nanometers principle error suppression in microprobe sensors

When the microprobe sensor is faced with the demand of high-speed biaxial displacement measurement, due to the characteristics of phase generated carrier (PGC) technology, accompanying optical intensity modulation (AOIM) and unfavorable phase modulation depth (PMD) will bring about the tens of nanometer cyclic nonlinear errors, further hindering high-speed and high-precision measurement. Herein, a light source intensity stabilization system based on semiconductor optical amplifier (SOA) feedback control is achieved to eliminate the error caused by AOIM in the presence of high-frequency and large-amplitude laser modulation. Based on this, the reasons for large nonlinear errors in biaxial measurements and the inability to ensure the stability of the accuracy of multiple measurement axes are methodically examined, and an effective nonlinear error elimination methodology based on the normalized amplitude correction of active temperature scanning is proposed. The continuity and linearity of the temperature scanning are also discussed. The performed experiments show that the above approach is capable of reducing the displacement demodulation error from the nanometer scale to the sub-nanometer scale. Further, the nonlinear error is reduced to within 0.1 nm for both measurement axes and the performance becomes consistent. The dual-axis measurement resolution of the microprobe sensor reaches 0.4 nm and the measurement speed is better than 1.2 m/s with the standard deviation of lower than 0.5 nm.

A method to partition boiling heat transfer mechanisms using synchronous through-substrate high-speed visual and infrared measurements

Heat transfer during boiling involves a variety of transport mechanisms. Available experimental techniques cannot yet fully delineate these mechanisms which has contributed to a long-standing, persistent challenge of constructing accurate mechanistic models for boiling. In this work, we develop a method to identify and distinguish between the individual heat transfer mechanisms that occur during boiling using synchronous, through-substrate, high-speed visual and infrared measurements. Local heat fluxes are deduced from temperature measurements and a synchronized set of binarized phase maps are obtained from processing high-speed visual measurements. Experimental pool boiling investigation of HFE-7100 fluid on an indium tin oxide surface revealed four distinct heat transfer signatures in the heat flux maps corresponding to liquid convection, contact line evaporation, vapor convection, and local microconvection due to rewetting during boiling. To classify these regions, pixel-wise binary and morphological operations are performed on the phase maps of the entire surface. In contrast with prior partitioning techniques which use standalone heat flux measurements, our synchronous high-resolution visualization enables the region classification around fine bubble footprints that otherwise would not be detected with heat flux maps alone. The heat fluxes and superheats are then partitioned into their underlying mechanisms using classified regions from the phase maps. Analysis of the nucleate boiling regime data shows that different mechanisms contribute in varying degrees to the overall heat transfer at different points along the boiling curve: for the surface-fluid combination studied, single-phase liquid heat transfer is the primary contributor at low heat fluxes while at high heat fluxes, contact line evaporation contributed the most. We further employ the experimental approach to partitioning dynamic processes resulting from step increases in heat input demonstrating its potential for investigating transient phenomena such as dryout. The experimental and post-processing method introduced in this study is the first to delineate partitioning between different heat transfer mechanism regions in the presence of multiple interacting bubbles over the entire surface throughout the boiling curve in both steady and transient operating conditions.

Pole balancing on the fingertip: model-motivated machine learning forecasting of falls.

Introduction: There is increasing interest in developing mathematical and computational models to forecast adverse events in physiological systems. Examples include falls, the onset of fatal cardiac arrhythmias, and adverse surgical outcomes. However, the dynamics of physiological systems are known to be exceedingly complex and perhaps even chaotic. Since no model can be perfect, it becomes important to understand how forecasting can be improved, especially when training data is limited. An adverse event that can be readily studied in the laboratory is the occurrence of stick falls when humans attempt to balance a stick on their fingertips. Over the last 20 years, this task has been extensively investigated experimentally, and presently detailed mathematical models are available. Methods: Here we use a long short-term memory (LTSM) deep learning network to forecast stick falls. We train this model to forecast stick falls in three ways: 1) using only data generated by the mathematical model (synthetic data), 2) using only stick balancing recordings of stick falls measured using high-speed motion capture measurements (human data), and 3) using transfer learning which combines a model trained using synthetic data plus a small amount of human balancing data. Results: We observe that the LTSM model is much more successful in forecasting a fall using synthetic data than it is in forecasting falls for models trained with limited available human data. However, with transfer learning, i.e., the LTSM model pre-trained with synthetic data and re-trained with a small amount of real human balancing data, the ability to forecast impending falls in human data is vastly improved. Indeed, it becomes possible to correctly forecast 60%-70% of real human stick falls up to 2.35 s in advance. Conclusion: These observations support the use of model-generated data and transfer learning techniques to improve the ability of computational models to forecast adverse physiological events.

Water Droplet Collison and Erosion on High-Speed Spinning Wheels

<div>The water droplet erosion (WDE) on high-speed rotating wheels appears in several engineering fields such as wind turbines, stationary steam turbines, fuel cell turbines, and turbochargers. The main reasons for this phenomenon are the high relative velocity difference between the colliding particles and the rotor, as well as the presence of inadequate material structure and surface parameters. One of the latest challenges in this area is the compressor wheels used in turbochargers, which has a speed up to 300,000 rpm and have typically been made of aluminum alloy for decades, to achieve the lowest possible rotor inertia. However, while in the past this component was only encountered with filtered air, nowadays, due to developments in compliance with tightening emission standards, various fluids also collide with the spinning blades, which can cause mechanical damage. One such fluid is the condensed water in the low-pressure exhaust gas recirculation channel (LP-EGR) formulated at cold starts and low-speed high load conditions. This kind of design has been developed to reduce nitrogen oxide emissions and is used in both gasoline and diesel engines. This article presents a state-of-the-art review of this WDE process, focusing on the formation of the condensed water before the compressor wheel, summarizing the influencing factors of WDE and the effects of the damage including using component testbench experiences and simulation methodologies. Inspection possibilities such as high-speed camera measurement and vibration analysis are also an important part of the document.</div>

High-speed laser centerline extraction and heterogeneous measurement architectures for low-cost hardware

Due to its real-time efficiency, stability, and reliability, structured light 3D measurement is widely used in measuring surface quality and manufacturing accuracy of industrial products. With the structured light measurement system's slow acquisition speed and low efficiency, it is difficult to meet the needs of online real-time detection, resulting in sparse 3D contour data and loss of details. To improve the algorithm's running speed and balance hardware resource consumption, a structured light extraction algorithm adapted to hardware acceleration is proposed, which executes the three low-coupling computational modules at eight-pixel parallel speed and in a pipelined manner. In order to further reduce the overall computational efficiency and deployment cost of high-speed structured light measurement tasks, an FPGA camera architecture with parallel acquisition and processing is designed, and the FPGA camera is cooperated with the CPU to form a more efficient heterogeneous measurement system. For samples of different materials and shapes, the standard deviation of sub-pixel coordinates extracted is less than 0.65. With this architecture, it is possible to process video stream with one million pixels at 500FPS, and the power consumption is 2.566w. Experimental results of measuring blocks and steel pipes show that the measurement error is below 0.15 mm. The proposed algorithm and heterogeneous processing measurement architecture are applicable in engineering, especially for high-speed real-time 3D measurement.

Investigation of the Lubricating Conditions in a Reciprocating Sliding Tribotest with Applied Electric Voltage

The appearance, evolution, and proliferation of electric-vehicle motors have introduced new challenges for lubricants. The appearance of electric currents in the shafts of electric motors can dramatically change the original properties of lubricated contacts, leading to mechanism failure. Understanding and controlling this phenomenon can be advantageous for lubrication, but investigating the lubricants requires specific equipment and conditions. Therefore, in this study, we introduced a ball-on-plate reciprocating tribometer capable of applying electric voltage to the elements of the friction pair and measuring the electric contact resistance (ECR) as feedback. Mineral-based paraffin oil was used as a lubricant in this study. The coefficient of friction (COF), wear, surface morphology, and composition were analysed. It was found that high-speed ECR measurement could give valuable information regarding the lubrication conditions in reciprocating friction pairs. This study shows that even tiny currents flowing through the tribo contact can alter the lubricating conditions. Moreover, the polarity of the applied voltage is also of great importance. Applying negative voltage to the harder surface can significantly increase wear if the tribo-film is based on surface oxidation.

Mode-shape magnification in high-speed camera measurements

If motion, identified using image-based methods, is too small to be seen with the naked eye, motion magnification can be used to help with the visualization. Established motion-magnification methods magnify (typically up to 1000 times) the band-passed content of the image data. Especially at higher frequencies, the amplitudes of measured displacements are often below the noise floor. In this research, a novel method for amplifying vibrations, based on experimental modal analysis (EMA), is introduced. The response of the examined structure to dynamic excitation is measured with a simplified, gradient-based, optical flow method and used to perform a hybrid modal analysis in conjunction with a reference accelerometer response measurement. Such a hybrid approach can: (a) identify structural dynamics significantly in the sub-pixel range, and (b) significantly below the image noise floor. The image of the vibrating structure is subdivided using a planar triangle mesh, which is then warped in accordance with the identified mode shape. A mesh-element-wise affine transformation is performed to obtain an image of the magnified mode shape. In the experimental part, the proposed method achieved magnification factors of approximately 40 thousand times, which is an order of magnitude deeper into noise than available before; additionally, the proposed approach is numerically significantly less demanding.The introduced mode-shape magnification presents an alternative to existing motion-magnification methods for applications where the harmonic displacement information is hidden by image noise.

Time-delay fourier transform spectrometer for high-speed spectral measurement

In the field of optics, there exist numerous chaotic processes like dissipative soliton dynamics, random laser generation, and laser scattering. It's very challenging to accurately capture the dynamics of these stochastic processes from the wavelength perspective with traditional spectrometers due to their slow signal integration speeds. Here, we propose a new approach, named time-delay Fourier transform spectrometer (TDFTS), to characterize the spectra of laser pulses with durations ranging from fs to ns with high speeds. Based on a fiber array with different lengths to impose frequency-dependent time delay, TDFTS efficiently maps the spectral distribution of light pulses to the temporal domain, and the spectrum can thus be detected with a photodiode and an oscilloscope. In experimental operation, the TDFTS provides spectral acquisition speeds up to 56 MHz frame rates and a bandwidth of tens of nanometers, while keeping comparable fidelity to traditional grating-scan spectrometers. While its spectral resolution of the current configuration is ∼0.1 nm, it can be further improved to 0.001 nm through optimizing the system. Based on its high speed, high spectral resolution, broad-bandwidth coverage, and compact configuration, TDFTS can be used to monitor nanosecond-scale spectral dynamics of non-repetitive optical processes.

Controlling reaction transfer between Al/Ni reactive multilayer elements on substrates

Reactive multilayers produce exothermic reaction with definite velocity and maximum temperature after ignition, which are the fundamental properties of the reactive multilayer systems. The generated heat with certain velocity makes it widely used in joining, bonding in the packaging, thermal batteries and many more applications. In this work, a distinct approach for achieving a reaction transfer between the reactive multilayers and different materials is demonstrated which can affect the generated temperature and velocity from the self-propagating properties of the reaction. For these intensions, we fabricated the Al/Ni reactive elements with certain separations between elements which allow to observe the reaction front transfer and emitted temperature in the reaction chain. The created separation between reactive elements are periodical and ordered systems with different thermal conductive properties. The temperature and definite velocity were measured by time-resolved pyrometer and high-speed camera measurements. SEM analysis showed the characteristics of the reaction transfer between reactive multilayer elements. It is predicted that: (I) The reaction front stops at a space with critical length; (II) Reducing heat loss through the substrate supports reaction front propagation through spaces; (III) Thermal property design of the spaces between the reactive elements enables property modification of the self-propagating reaction.Graphical abstract

Comparative study of variant shifting-phase coding method based on noise error model

Phase shifting algorithm, which is well-known for its high-accuracy and high-resolution, plays a crucial role in fringe projection profilometry. A class of variant shifting-phase coding method (VSPCM) has been proposed for high-speed 3D measurement. The three kinds of VSPCM include the inner shifting-phase method (ISPM), the intensity-coded method (ICM) and the modified Carré algorithm (MCA). These methods project only four patterns avoiding the need for extra images, yet achieve accuracy comparable to the classical three-frequency heterodyne method. In VSPCM, the shifting-phase, as a key code-word for phase unwrapping, is encoded as a variable value. In practice, the noise and the encoding of shifting-phase have varying degrees of impact on the performance of these methods. But the coded ranges of the shifting-phase were previouly empirical values. Besides, there are no studies related to these factors, and also a lack of comparative researches on such methods. This paper compares three kinds of VSPCM for the first time. We derive the noise error models for shifting-phase and wrapped phase in three methods and examine the impact of variant shifting-phase on fringe orders and wrapped phase in these methods. We find that the abnormal shifting-phase errors predominantly cause fringe orders errors. Fortunately, median filtering can effectively handle shifting-phase errors to ensure successful phase unwrapping. To improve their accuracy, we also deduce that the optimal shifting-phase encoding range is [−77°, 77°] for ISPM, and is [−61°, 61°] for ICM, and is [34°, 74°] for MCA. For wrapped phase errors, the distributions of ICM and MCA exhibit a U-shaped distribution, while ISPM demonstrates a uniform distribution. Based on theoretical analysis and experiment results, this paper gives recommendations for better use of these methods to boost their accuracy and offers valuable guidance for selecting an appropriate VSPCM under the specific measurement requirements.

High-sensitivity and high-speed measurements of ultrashort pulses as short as 74 fs at 1.9 µm using a GRENOUILLE device.

Ultrashort laser pulse sources in the wavelength range of 1.8 to 2 µm have many potential applications including medicine, materials processing, and sensing. In the use of such lasers, a crucial task is to measure their pulse's temporal intensity and phase. Such measurement devices are most useful when they are simple to build and operate and also have high speed and high sensitivity. The GRENOUILLE measurement device with few components, no moving parts, sensitivity of hundreds of picojoules, and measurement speed of hundreds of milliseconds, is commonly used to solve this problem at other wavelengths. In this paper, the measurement of ultrashort pulses by a GRENOUILLE device, developed using a silicon matrix sensor, for pulses in the wavelength range of 1.8 to 2 µm has been demonstrated. It is shown that ultrashort pulses with durations of 74 to 900 fs and a maximum spectral FWHM of 85 nm can be measured with this device. The recently developed ultra-reliable RANA approach was used for pulse retrieval from the measured traces. The device's performance was validated by comparing its measurements with those obtained by the robust FROG technique.

High-speed imaging of evoked rodent mechanical behaviors yields variable results that are not predictive of inflammatory injury.

Few analgesics identified using preclinical models have successfully translated to clinical use. These translational limitations may be due to the unidimensional nature of behavioral response measures used to assess rodent nociception. Advances in high-speed videography for pain behavior allow for objective quantification of nuanced aspects of evoked paw withdrawal responses. However, whether videography-based assessments of mechanical hypersensitivity outperform traditional measurement reproducibility is unknown. First, we determined whether high-speed videography of paw withdrawal was reproducible across experimenters. Second, we examined whether this method distinguishes behavioral responses exhibited by naive mice and mice with complete Freund's adjuvant (CFA)-induced inflammation. Twelve experimenters stimulated naive C57BL/6 mice with varying mechanical stimuli. Paw withdrawal responses were recorded with high-speed videography and scored offline by one individual. Our group was unable to replicate the original findings produced by high-speed videography analysis. Surprisingly, ∼80% of variation was not accounted for by variables previously reported to distinguish between responses to innocuous and noxious stimuli (paw height, paw velocity, and pain score), or by additional variables (experimenter, time-of-day, and animal), but rather by unidentified factors. Similar high-speed videography assessments were performed in CFA- and vehicle-treated animals, and the cumulative data failed to reveal an effect of CFA injection on withdrawal as measured by high-speed videography. This study does not support using paw height, velocity, or pain score measurements from high-speed recordings to delineate behavioral responses to innocuous and noxious stimuli. Our group encourages the continued use of traditional mechanical withdrawal assessments until additional high-speed withdrawal measures are validated in established pain models.

Research on flow field quality measurement of super high speed circulating water channel based on LDV

The flow field quality of the super high speed circulating water channel (SHSCWC) test section in the open (with a free liquid surface state) and closed (with a cavitation tunnel state) was studied. An array of flow field measuring points was established to measure the axial velocity using a laser doppler velocimeter (LDV) for both states. Meanwhile, ultrasonic sensors were used to measure the levelness of the free liquid surface in the test section. The measurement results indicated that in the open state, the non-uniformity and instability of 8 kinds of flow velocity in the flow field section are less than 1.0%, respectively, while the free liquid surface level is less than 25mm at the flow rate of 8m/s. In the closed state, the non-uniformity and instability of eight types of flow velocity in the flow field section are all below 1.0%, with turbulence being less than 0.5%. The measurement results in both states meet the requirements of technical indicators, and provide data support for the experimental research and optimal design of the SHSCWC.

Effect due to Cs injection upon current oscillation of the beam extracted from the J-PARC negative hydrogen ion source

A high-speed emittance measurement system installed at the J-PARC RF negative hydrogen (H-) ion source test stand can construct emittance diagrams of the beam of a specific frequency component. The driving 2 MHz RF power produces small amplitude oscillating components at 2 MHz and at higher harmonic frequencies in the total H- ion beam detected by a Faraday installed downstream of the emittance measurement system. Magnitudes of oscillating component at 2 MHz and 4 MHz frequencies become appreciable as the slits of the emittance measurement system separate the H- ion beam into the position/angle resolved phase space elements. The reconstructed emittance diagrams of H- ion beams for the operation condition with continuous supply of Cs realizing large H- ion current to total extraction current ratios indicate that 2 MHz and 4 MHz frequency oscillating beam components propagate surrounding the center DC beam. Both 2 MHz and 4 MHz oscillating beam components comprise two to three beam particle groups in the phase space. The DC component of the H- ion beam exhibit a single peak in the angular distribution. Meanwhile, oscillating components often take the minima where the DC H- ion beam takes the maximum in the angular distribution diagram. Thus, the regions that produce large amplitude oscillations of the H- ion beam are considered located at the circumference of the beam extraction aperture. One possible explanation for observing larger amplitude beam oscillation can be the enhanced H- ion surface production at the plasma facing the wall of the beam extraction aperture. The operation without the Cs delivery to the source increased electron current coextracted with H- ions and changed the structure of the beam emittance diagram. In the direction perpendicular to the magnetic fields created by a magnetic filter and electron suppression magnets, the peak of the 4 MHz oscillating beam components appeared at the center of the DC beam. This observation suggests the extraction of H- ions formed in the central region by the volume production process near the internal RF antenna. Mechanisms that can excite and diminish the beam fluctuation amplitudes of the extracted H- ion beam are discussed.