High Power Conversion Efficiency Research Articles

Filtered spectrum modeling of high-performance perovskite tandem solar cells: Tailoring absorber properties and electron/hole transport layers for 31.55 % efficiency

In this study, the perovskite tandem solar cell (TPSC) has been accomplished using SCAPS-1D. The present study focuses on comprehensive exploration and detailed optimization using various strategies constructing a tandem device. To calculate high photovoltaic power conversion efficiency (PCE), the numerical analysis has been carried out for a wide-bandgap halide (WBH) FA0.75Cs0·25Pb(I0·8Br0.2)3 of bandgap 1.67eV and a Pb–Sn based narrow-bandgap halide (NBH) FA0.7MA0.3Pb0·5Sn0·5I3 of bandgap 1.22eV as absorber layer in top-cell (TCELL) and bottom-cell (BCELL) respectively. The WBH has huge potential as a front light absorber and the NBH based BCELL provides stability and high performance by accepting high and low energy photons respectively. This method mitigates thermalization and non-absorbed photon loss which results in the growth in PCE. The proposed work demonstrates the impact of active-layer thickness along with defect density on the solar-cell parameters. It has been observed that defect density is low for the optimal performance. An investigation for various electron transport medium (ETMs) and hole transport medium (HTMs) has been done to secure an optimum performing TCELL as well as BCELL. Using filtered-spectrum study along with current-matching method, every PV metric parameter has been analyzed after their deployment into tandem configuration. The numerical investigation has shown promising photovoltaic parameters with aa high open circuit voltage (VOC) of 2.33 V, a short circuit current density (JSC) of 17.07 mA/cm2, a fill factor (FF) of 79.34 % and PCE of 31.55 % in tandem configuration.

Enhanced photovoltaic response in WSe2 photodetector with asymmetric two-dimensional contacts

Asymmetric contact pairs with different work functions provide an efficient method to extract photogenerated carriers in optoelectrical devices. Specifically, vertical optoelectrical devices based on two-dimensional (2D) materials utilize graphene layers as the bottom and top contacts. Whereas an additional terminal is required for electrostatic doping in either top or bottom graphene to enlarge the built-in electric field. Herein, we present an enhanced photovoltaic response in a vertical WSe2 photodetector utilizing asymmetric 2D contacts. A graphite layer and a degenerate SnSe2 are used as the top and bottom contacts, respectively, with a significant difference in their work functions. By establishing a large built-in electric field across the vertical WSe2 layer, a strong photovoltaic effect is achieved, resulting in an open-circuit voltage of 0.37 V and a short-circuit current of 0.42 μA under 532 nm illumination. The device shows high-performance photodetection characteristics, with a responsivity of 32.04 A W−1, external quantum efficiency of 7475%, and specific detectivity of 3.61 × 1012 Jones. Furthermore, the device can generate a maximum output electrical power of 70.9 nW, enabling a high-power conversion efficiency of 3.5%.

Highly efficient and stable perovskite solar cell with sodium glycinate additive

Organic halide perovskite solar cells (PSCs) with high power conversion efficiency (PCE) and low manufacturing cost have been attracting considerable attention. However, defects in perovskite as recombination centers and ion migration paths seriously deteriorate the optoelectronic performance of PSCs. Herein, a facile strategy is devised by introducing sodium glycinate (SG) mulit-functional additive into perovskite to passivate defects. In this way, the typical defects of mismatched leads in perovskite can be passivated by forming ionic bond with carboxylate radical or coordination bond with amino groups of SG. Also, the SG molecules with cross-linking function could improve the grain sizes of perovskite to reduce defects and increase light absorption. Besides, sodium ions of SG can impede the ion migration in perovskite and strengthen the interfacial charge transfer ability. As a result, the PSCs assembled under air condition with SG additive achieved a champion conversion efficiency of 19.32 % due to the comprehensive action of SG, and an improved stability under work and storage conditions. This provides an economical and effective strategy for the industrialization of PSCs.

An Efficient Fiber Gel Dye‐Sensitized Solar Cell with Stable Interlaced Interfaces

AbstractFiber gel dye‐sensitized solar cells (FGDSCs) are recognized as an effective solution for high‐performance, durable and safe wearable power supply. However, poor and unstable interfaces between fiber electrodes and gel electrolytes are bottleneck problems that have restricted the photovoltaic performances of FGDSCs and their stabilities during deformations. Here, an FGDSC with stable interlaced interfaces is designed by incorporating polymerized gel electrolyte into the aligned channels in fiber electrodes and the gaps between photoanode and counter electrode in situ. The interlaced structure of gel electrolyte in FGDSC improves the interfacial stability and provided stable channels for rapid ion diffusions, offering efficient charge transports at interfaces. The resulting FGDSC thus produced a high power conversion efficiency of 7.95%, and it is further maintained by over 90% after bending for 5000 cycles. These FGDSCs can be integrated with fiber batteries as a self‐charging power system, demonstrating an effective power solution for wearables.

Soft Lattice and Phase Stability of α‐FAPbI3

AbstractSince the certified power conversion efficiency (PCE) of perovskite solar cells (PSCs) has reached 26.1%, exactly equal to that of crystalline silicon solar cells, a strong demand for ensuring the long‐term stability of PSCs has arisen for commercialization. The intrinsic stability of the perovskite layer must be guaranteed as a top priority to ensure the whole device's stability. Recently, the state‐of‐the‐art PSCs, performing a high PCE, employ α‐FAPbI3 (FA = formamidinium) for the perovskite layer in spite of its metastable tendency to spontaneously transform into its photoinactive polymorph at PSC operating temperature. In this review paper, the intrinsic structural stability of α‐FAPbI3 soft lattice is understood from the thermodynamic point of view, with key parameters to restrain the undesirable phase transition. Besides, reported experimental results are closely examined to find fundamental origins, derive the enhanced phase stability in each experiment, and understand their role in maintaining the lattice structure from the collective perspective.

The Role of Solution Aggregation Property toward High-Efficiency Non-Fullerene Organic Photovoltaic Cells.

In organic photovoltaic cells, the solution-aggregation effect (SAE) is long considered a critical factor in achieving high power-conversion efficiencies for polymer donor (PD)/non-fullerene acceptor (NFA) blend systems. However, the underlying mechanism has yet to be fully understood. Herein, based on an extensive study of blends consisting of the representative 2D-benzodithiophene-based PDs and acceptor-donor-acceptor-type NFAs, it is demonstrated that SAE shows a strong correlation with the aggregation kinetics during solidification, and the aggregation competition between PD and NFA determines the phase separation of blend film and thus the photovoltaic performance. PDs with strong SAEs enable earlier aggregation evolutions than NFAs, resulting in well-known polymer-templated fibrillar network structures and superior PCEs. With the weakening of PDs' aggregation effects, NFAs, showing stronger tendencies to aggregate, tend to form oversized domains, leading to significantly reduced external quantum efficiencies and fill factors. These trends reveal the importance of matching SAE between PD and NFA. The aggregation abilities of various materials are further evaluated and the aggregation ability/photovoltaic parameter diagrams of 64 PD/NFA combinations are provided. This work proposes a guiding criteria and facile approach to match efficient PD/NFA systems.

High Performance As-Cast Organic Solar Cells Enabled by a Refined Double-Fibril Network Morphology and Improved Dielectric Constant of Active Layer.

High performance organic solar cells (OSCs) are usually realized by using post-treatment and/or additive, which can induce the formation of metastable morphology, leading to unfavorable device stability. In terms of the industrial production, the development of high efficiency as-cast OSCs is crucially important, but it remains a great challenge to obtain appropriate active layer morphology and high power conversion efficiency (PCE). Here, efficient as-cast OSCs are constructed via introducing a new polymer acceptor PY-TPT with a high dielectric constant into the D18:L8-BO blend to form a double-fibril network morphology. Besides, the incorporation of PY-TPT enables an enhanced dielectric constant and lower exciton binding energy of active layer. Therefore, efficient exciton dissociation and charge transport are realized in D18:L8-BO:PY-TPT-based device, affording a record-high PCE of 18.60% and excellent photostability in absence of post-treatment. Moreover, green solvent-processed devices, thick-film (300nm) devices, and module (16.60 cm2) are fabricated, which show PCEs of 17.45%, 17.54%, and 13.84%, respectively. This work brings new insight into the construction of efficient as-cast devices, pushing forward the practical application of OSCs.

All-Round Passivation Strategy Yield Flexible Perovskite/CuInGaSe2 Tandem Solar Cells with Efficiency Exceeding 26.5.

The perovskite/Cu(InGa)Se2 (CIGS) tandem solar cells (TSCs) presents a compelling technological combination poised for the next generation of flexible and lightweight photovoltaic (PV) tandem devices, featuring a tunable bandgap, high power conversion efficiency (PCE), lightweight flexibility, and enhanced stability and durability. Over the years, the imperative to enhance the performance of wide bandgap (WBG) perovskite solar cells (PSCs) has grown significantly, particularly in the context of a flexible tandem device. In this study, an all-round passivation strategy known as Dual Passivation at Grains and Interfaces (DPGI) is introduced for WBG PSCs in perovskite/CIGS tandem structures. The implementation of DPGI is tailored to improve film crystallinity and passivate defects across the solar cell structure, leading to a substantial performance enhancement for WBG PSCs. Subsequently, both rigid and flexible tandem devices are assembled. Impressively, a fully flexible 4T perovskite/CIGS TSCs is successfully fabricated with a PCE of 26.57%, making it the highest value in this field and highlighting its potential applications in the next generation of flexible lightweight PV tandem devices.

Enhancing CsSn0.5Ge0.5I3 Perovskite Solar Cell Performance via Cu2O Hole Transport Layer Integration

Perovskite solar cells (PSCs) have emerged as a promising alternative to traditional silicon solar cells due to their low cost of fabrication and high power conversion efficiency (PCE). The utilization of lead halide perovskites as absorber layers in perovskite solar cells has been impeded by two major issues: lead poisoning and stability concerns. These hindrances have greatly impeded the industrialization of this cutting-edge technology. In light of the harmful effects of lead in perovskite solar cells, researchers have shifted their attention to exploring lead-free metal halide perovskites. However, the present alternatives to lead-based perovskite exhibit poor performance, thus prompting further inquiry into this matter. The primary objective of this research is to investigate the use of Cu2O as a hole transport layer in combination with lead-free metal halide perovskite (CsSn0.5Ge0.5I3) to achieve superior performance. Through meticulous experimentation, the suggested model has achieved outstanding results by optimizing several key variables. These variables include the thickness of the absorber layer (CsSn0.5Ge0.5I3), defect density, and doping densities, as well as the back contact work function and the operating temperature associated with each layer. The proposed FTO/PC60BM/CsSn0.5Ge0.5I3/Cu2O/Au solar cell structure surpassed prior configurations by comprehensively examining key aspects such as absorber layer thickness and defect density, doping densities, and back contact work. The structure has been also compared with multiple electron transport elements and concluded that the proposed model functions superior due to the use of PC60BM as an electron transport layer and it has an improved electron extraction procedure. Finally, the proposed model has achieved the optimized values as Jsc of 31.56 mA/cm-2, Voc of 1.12 V, FF of 81.47%, and PCE of 27.72%. As a consequence of this research, the investigated structure may be an excellent contender for the eventual creation of lead-free solar power cells made from perovskite.

Design highly effective B or N doped mesoporous carbon fibers catalysts for I3-/I- redox couple regeneration in carbon-based dye-sensitized solar cells

Construction of mesoporous structure and improving the conductivity of carbon counter electrode are feasible paths to enhance the catalytic activity in dye-sensitized solar cells (DSCs) toward the I3-/I- redox couple regenerating (IRR). Herein, mesoporous carbon fiber (PCf) has been first synthesized and the DSCs using PCf counter electrode results in a power conversion efficiency (PCE) of 7.12%, significantly surpassing the PCE of 6.01% generated by the DSCs with carbon fiber (Cf) counter electrode without mesoporous structure. Additionally, doping with heteroatoms B or N can further enhance the catalytic performance of PCf. Consequently, B or N doped Cf (BPCf or NPCf) counter electrode-based DSCs achieve high PCE values of 8.43% and 7.96%, respectively, demonstrating PCE improvements of 40.3% and 32.4%. This enhancement in catalytic activity for IRR in DSCs can be first attributed to the increased specific surface area of Cf which can provide more catalytic activated sites. Meanwhile, the enhanced conductivity of PCf by heteroatoms B or N doping is also an important factor for the improved catalytic activity. This work is expected to provide potential path to enhanced the catalytic activity of carbon counter electrode in DSCs toward IRR.

Manipulating Crystal Growth and Secondary Phase PbI2 to Enable Efficient and Stable Perovskite Solar Cells with Natural Additives

HighlightsThe novel ionic cellulose derivative with cyano-imidazolium cation and chloride anion, designed from natural cellulose, promotes the crystallization process, grain growth, and orientation of perovskite in perovskite solar cells (PSCs).The use of ionic cellulose leads to the suppression of defect formation, reduction of grain boundaries, enhancement of carrier extraction, and inhibition of non-radiative recombination, resulting in a high power conversion efficiency of 24.71% in PSCs.The biopolymer-based approach enables excellent stability of PSCs, which maintain over 91.3% of their initial efficiencies after 3000 h in conventional air atmosphere.

Chemical Reaction of FA Cations Enables Efficient and Stable Perovskite Solar Cells.

Organometal halide perovskite solar cells (PSCs) have received great attention owing to a rapid increase in power conversion efficiency (PCE) over the last decade. However, the deficit of long-term stability is a major obstacle to the implementation of PSCs in commercialization. The defects in perovskite films are considered as one of the primary causes. To address this issue, isocyanic acid (HNCO) is introduced as an additive into the perovskite film, in which the added molecules form covalent bonds with FA cations via a chemical reaction. This chemical reaction gives rise to an efficient passivation on the perovskite film, resulting in an improved film quality, a suppressed non-radiation recombination, a facilitated carrier transport, and optimization of energy band levels. As a result, the HNCO-based PSCs achieve a high PCE of 24.41% with excellent storage stability both in an inert atmosphere and in air. Different from conventional passivation methods based on coordination effects, this work presents an alternative chemical reaction for defect passivation, which opens an avenue toward defect-mitigated PSCs showing enhanced performance and stability.

DFT combined to Boltzmann transport theory for optoelectronic and thermoelectric properties investigations for Se (4 & 8 (at.%)) doped Li2SnS3

Cubic Li2SnS3 emerges as a noteworthy ionic conductor and a viable electrode material for lithium secondary batteries. Its application extends to solar cell technologies, owing to its commendable optoelectronic properties and high-power conversion efficiency. In this study, we present density functional theory (DFT)-based first principles calculations for Li2SnS3-xSex (x = 0, 4, and 8% (atomic percent (at.%)) utilizing the modified Becke Johnson (mBJ) approximations, proposing a compelling alternative. Our investigation reveals significant optical absorption in the ultraviolet region for Li2SnS3-xSex (x = 0, 4, and 8%), accompanied by modest effective mass and indirect band gaps of 2.18 eV for the pristine material. Conversely, doped materials exhibit direct band gaps, with values of 2.113 eV for 4% and 2.026 eV for 8%. Furthermore, the calculated thermoelectric power factor underscores the potential and efficacy of Li2SnS3-xSex in thermoelectric energy devices. The findings not only highlight the material’s promise for solar applications but also underscore its candidacy as a novel solid-state electrolyte for lithium-ion batteries. This stems from its robust thermal stability and notable lithium-ion conductivity, positioning Li2SnS3 as a compelling candidate for advanced energy storage technologies.

High efficiency and stability of perovskite solar cells prepared by alkali metal interfacial modification

Perovskite solar cells (PSCs) have attracted much attention at home and abroad due to their excellent photoelectric properties. Defects in the electron transport layer (ETL) and ETL/perovskite interface greatly affect the power conversion efficiency (PCE) and stability of PSCs. In the paper, the surface of tin dioxide (SnO2) ETL was modified by an alkali metal salt (NaBr, KBr, and RbBr) solution to optimize electron transport and passivate SnO2/perovskite. The results show that the photovoltaic performance of the PSCs is significantly improved after interfacial modification, especially the KBr-modified PSC has the highest PCE, which is 7.8% higher than that of the unmodified device, and the open-circuit voltage, short-circuit current density and fill factor are all greatly improved. This improvement is attributed to the fact that interfacial modification reduces the trap density of the SnO2 films, increases the mobility of the SnO2 films film, effectively passivates defects, and significantly inhibits the recombination at the SnO2/perovskite interface. This method aims to use simple and low-cost inorganic materials for effective interface modification.

Hybrid Two‐Step Inkjet‐Printed Perovskite Solar Cells

Perovskite photovoltaics are on their way to commercialization, but crucial advancements are still required to realize scalable and reliable fabrication processes Concerning solution processing of perovskite top solar cells, the hybrid two‐step process offers an auspicious combination of good thin‐film formation control, even on textures, and high power conversion efficiencies (PCEs). Herein, a scalable fabrication process that consists of a hybrid two‐step process and combines evaporated PbI2 with inkjet‐printed organic precursor materials is addressed. It is shown that optimizing the printing parameters enables high PCEs, high reproducibility, and the potential for conformal growth on textured silicon. The perovskite films are free of macroscopic drying effects and omit the use of toxic solvents. To achieve optimal conversion, the morphology of the PbI2 thin film and the selected resolution in the printing process are decisive. To facilitate intermixing and enable stoichiometry, a dimethyl sulfoxide vapor treatment is introduced to increase the PbI2 porosity. Reproducible PCEs are demonstrated with champion devices showing 18.2% which are on par with spin‐coated counterparts. In the results, it is demonstrated that the hybrid two‐step process with an inkjet‐printed second step is a promising scalable process for reliable and high‐quality perovskite deposition even on texture, thereby paving the path toward industrialization.

Design and Optimization of High-Performance Novel RbPbBr3-Based Solar Cells with Wide-Band-Gap S-Chalcogenide Electron Transport Layers (ETLs).

Inorganic cubic rubidium-lead-halide perovskites have attracted considerable attention owing to their structural, electronic, and unique optical properties. In this study, novel rubidium-lead-bromide (RbPbBr3)-based hybrid perovskite solar cells (HPSCs) with several high-band-gap chalcogenide electron transport layers (ETLs) of In2S3, WS2, and SnS2 were studied by density functional theory (DFT) and using the SCAPS-1D simulator. Initially, the band gap and optical performance were computed using DFT, and these results were utilized for the first time in the SCAPS-1D simulator. Furthermore, the impact of different major influencing parameters, that is, the thickness of the layer, bulk defect density, doping concentration, and defect density of interfaces, including the working temperature, were also investigated and unveiled. Further, a study on an optimized device with the most potential ETL (SnS2) layer was performed systematically. Finally, a comparative study of different reported heterostructures was performed to explore the benchmark of the most recent efficient RbPbBr3-based photovoltaics. The highest power conversion efficiency (PCE) was 29.75% for the SnS2 ETL with Voc of 0.9789 V, Jsc of 34.57863 mA cm-2, and fill factor (FF) of 87.91%, while the PCEs of 21.15 and 24.57% were obtained for In2S3 and WS2 ETLs, respectively. The electron-hole generation, recombination rates, and quantum efficiency (QE) characteristics were also investigated in detail. Thus, the SnS2 ETL shows strong potential for use in RbPbBr3-based hybrid perovskite high-performance photovoltaic devices.

Development of natural dye photosensitizers for dye-sensitized solar cells: a review.

Dye-sensitized solar cell (DSSC) is a photovoltaic device that can be produced from natural source pigments or natural dyes. The selection of natural dyes for DSSC application is currently under research. The utilization of natural dye materials that are easy to obtain, cost-effective, and non-toxic can reduce waste during DSSC fabrication. Natural dyes can be extracted from plants through extraction and chromatography methods. The suitability and viability of utilizing natural dyes as photosensitizers in DSSCs can be predicted using appropriate software simulation by varying related parameters to produce high power conversion efficiency. In this context, the purpose of the review is to highlight the evolution of performance improvement in the development of DSSCs with consideration of natural dye extraction and software simulation. This review also focuses on the results of extracting natural dyes from herbal ingredients, which are still very limited in information, and several parts of herbal plants that can be used as natural dye sources in the future of solid-state DSSCs have been identified. Based on the results of this review, the highest efficiency was obtained for the DSSC that used chlorophyll pigments as natural dyes using Peltophorum pterocarpum leaves with 6.07%, followed by anthocyanin pigments as natural dyes using raspberries (black) fruits with 1.5%, flavonoid pigments as natural dyes using Curcuma longa herbs with 0.64%, and flavonoid pigments as natural dyes using Indigofera tinctoria flowers with 0.46%.

Polymerized-Small-Molecule Acceptors Featuring Siloxane-Terminated Side Chains for Mechanically Robust All-Polymer Solar Cells.

Flexible and stretchable organic solar cells (OSCs) show great promise in wearable and stretchable electronic applications. However, current high-performance OSCs consisting of polymer donors (PDs) and small-molecule acceptors (SMAs) face significant challenges in achieving both high power conversion efficiency (PCE) and excellent stretch-ability. In this study, we synthesized a new polymerized-small-molecule acceptor (P-SMA) PY-SiO featuring siloxane-terminated side chains and compared its photovoltaic and mechanical performance to that of the reference PY-EH with ethylhexyl-terminated side chains. We found that the incorporation of siloxane-terminated side chains in PY-SiO enhanced the molecular aggregation and charge transport, leading to an optimized film morphology. The resultant of all-polymer solar cells (all-PSCs) based on PBDB-T/PY-SiO showed a higher PCE of 12.04% than the PY-EH-based one (10.85%). Furthermore, the siloxane-terminated side chains also increased the interchain distance and provided a larger free volume for chain rotation and reconfiguration, resulting in a higher film crack-onset strain (COS: 18.32% for PBDB-T/PY-SiO vs 11.15% for PBDB-T/PY-EH). Additionally, the PY-SiO-based stretchable all-PSCs exhibited an impressive PCE of 9.8% and retained >70% of its original PCE even under a substantial 20% strain, exceeding the performance of the PY-EH-based stretchable all-PSCs. Our result suggests the great potential of the siloxane-terminated side chain for achieving high-performance and stretchable OSCs.

Chalcogen Atoms Regulate the Organic Solar Cell Performance of B-N-Based Polymer Donors.

Donor polymers play a key role in the development of organic solar cells (OSCs). B-N-based polymer donors, as new types of materials, have attracted a lot of attention due to their special characteristics, such as high E(T1), small ΔEST, and easy synthesis, and they can be processed with real green solvents. However, the relationship between the chemical structure and device performance has not been systematically studied. Herein, chalcogen atoms that regulate the OSCs performance of B-N-based polymer donors were systematically studied. Fortunately, the substitution of a halogen atom did not affect the high E(T1) and small ΔEST character of the B-N-based polymer. The absorption and energy levels of the polymer were systematically regulated by O, S, and Se atom substitution. The PBNT-TAZ:Y6-BO-based OSCs device demonstrated a high power conversion efficiency of 15.36%. Moreover, the layer-by-layer method was applied to further optimize the device performance, and the PBNT-TAZ/Y6-BO-based OSCs device yielded a PCE of 16.34%. Consequently, we have systematically demonstrated how chalcogen atoms modulated the electronic properties of B-N-based polymers. Detailed and systematic structure-performance relationships are important for the development of next-generation B-N-based materials.

Perylene Diimide‐Based Low‐Cost and Thickness‐Tolerant Electron Transport Layer Enables Polymer Solar Cells Approaching 19% Efficiency

AbstractThe materials for electron transport layers (ETLs) play a significant role in the performance of polymer solar cells (PSCs) but face challenges, such as low electron transport mobility and conductivity, low solution processibility, and extreme thickness sensitivity, which will undermine the photovoltaic performance and hinder compatibility of large‐scale fabrication technique. To address these challenges, a new n‐type perylene diimide‐based molecule (PDINB) with two special amine‐anchored long‐side chains is designed and synthesized feasibly. PDINB shows very high solubility in common organic solvents, such as dichloromethane (>75 mg ml−1) and methanol with acetic acid as an additive (>37 mg ml−1), which leads to excellent film formability when deposited on active layers. With PDINB as ETLs, the photovoltaic performance of the PSCs is boosted comprehensively, leading to power conversion efficiency (PCE) up to 18.81%. Thanks to the strong self‐doping effect and high conductivity of PDINB, it displays an appreciable thickness‐tolerant property as ETLs, where the devices remain consistently high PCE values with the thickness varying from 5 to 30 nm. Interestingly, PDINB can be used as a generic ETL in different types of PSCs including non‐fullerene PSCs and all‐polymer PSCs. Therefore, PDINB can be a potentially competitive candidate as an efficient ETL for PSCs.