Higher Material Removal Rate Research Articles

Machinability and pulse characteristics of Ti-16Al-14Nb (α/β) alloy in wire-electric discharge machining process: A surface integrity study

The goal of the present work is to produce the efficient cutting of Ti-16Al-14Nb (α/β) alloy through wire-electric discharge machining and contemplate the terminologies such as machining ability, surface integrity and material removing capability. For this, the experimentation has been designed by considering three process parameters, pulse-on time ( Ton), pulse-off time ( Toff) and peak current ( Ip) at three significant levels (low, high, intermediate) in L27 order designed from design of experiments. The effect of these process variables on pulse characteristics, surface roughness ( Ra), kerfwidth ( Kw) and material removal rate ( MRR) is analyzed and mathematically modeled with analysis of variance. The results state that the highest MRR (0.521, 0.51, 0.506 mm3/sec) and low surface roughness (8.91, 8.89, 8.68 µm) values are observed at the highest level (110 µs, 15 µs, 8 A). If the pulse duration is kept at low ( Ton = 40µs, Toff = 3µs), the increase in peak current from 3 A to 8 A leads to a 64.54% increase in MRR and a 52.9% increase in Ra values. ANOVA results stated that Ton has contributed 20.4%, 35.8% and 19.3%, and Ip has contributed 43.1%, 30.5% and 46.6% influence on MRR, Kw and Ra respectively. The voltage–current characteristics studies confirmed that the strong intense pulses at a higher peak current (8 A) resulted in the increased MRR (0.521 mm3/sec) and Ra (8.43 µm) leading to the formation of swages and ridges. The surface integrity analysis derived from Abbott–Firestone curve agreed that the lowest level has shown better skewness ( Rsk = −0.274) and at highest level showed a larger deviation in skewness ( Rsk = +2.672) signifies that higher asymmetry (poor) of the surface.

Parametric analysis, modeling and optimization of the process parameters in electric discharge machining of aluminium metal matrix composite

Optimizing electric discharge machining (EDM) for aluminum/SiCp metal matrix composites poses challenges due to intricate machine parameters and process complexity, impacting process economy and elevating product costs. The research aims to find the optimal combination of process parameters which include pulse on-time, pulse current, duty cycle (%), gap voltage, sensitivity and flushing pressure for EDM of Al/SiCp-MMC using a copper electrode for the selected response factors such as material erosion rate and surface roughness, Ra. The experiments were designed using the central composite design of response surface methodology and an advanced optimization technique known as Teaching–learning-based optimization (TLBO), is applied to find the optimal combination of process parameters to obtain maximum material erosion rate subject to the desired range of surface roughness (SR), Ra. The combination of the high pulse on-time (i.e. 150 μs) and high pulse current (i.e. 12A) results in high material removal rate with deep craters on the machined surface clearly visible in SEM images contrasting the minimized surface roughness at lower values of pulse on-time (50 μs) and the pulse current (4A). Pulse on - time (Ton) is found to be the most significant factor for material erosion rate and surface roughness with percentage contribution of 70.86 and 54.9 respectively for optimization of the response. The regression models were developed at 95% confidence level for material removal rate and surface roughness with R2 value of 0.93 and 0.95 respectively signifying high degree of accuracy in predicting the response. Confirmation tests conducted to check the adequacy of the established models revealed that the percentage error between the predicted and experimental responses is found to be within acceptable levels. Electron discharge machining of the aluminium metal matrix composite at the optimized conditions could provide economical aspect in the aerospace and automobile industry.

3D printed compliance tool incorporated internal-impeller structure for high performance face grinding of titanium alloy

During compliant face grinding of difficult-to-machine areas like the blade runner surface, significant heat accumulation at the tight interface between the workpiece and tool. This leads to limitations in surface integrity and tool life longevity. This study introduces a novel cooling method that incorporates an axially rotating impeller into the cavity of a small compliant grinding tool. The internal impeller structured compliant tool was prepared base on additive manufacturing. Numerical simulations and experimental studies were carried out to investigate its heat transfer mechanisms and its effect on the continuous grinding performance. The findings indicate that while favorable surface roughness and high material removal rates coincide with elevated grinding temperatures, the Shore hardness of the flexible material decreases as the grinding temperature rises. Consequently, there is a reduction in grit cutting depth and an increase in the proportion of rubbing and ploughing grit due to the grit’s height rearranges. The designed internal impeller facilitates the external cooling air with internal vortices to reach the grinding interface zone limiting heat accumulation to below 91.0°C and removing chips to reduce grit adhesion. Consequently, the grinding performance was more consistent, with a stable material removal depth ranging from 97 µm to 103 µm. 3D-printing-based compliant tools provide new insights into consistently high grinding performance for complex parts.

Investigation of the influence of different types of electrolytes on the performance of the Electrochemical Discharge Machining process during micromachining of molybdenum

Electrochemical Discharge Machining (ECDM) is a hybrid process that integrates the principles of Electrochemical Machining (ECM) and Electrical Discharge Machining (EDM) to create micro-holes in both conductive and non-conductive materials that are typically difficult to machine. Given the unpredictable nature of this hybrid method, the composition of the electrolyte emerges as a critical factor influencing the accuracy and performance of the machining process. Consequently, the optimization and analysis of electrolytes are pivotal for the efficient utilization of energy during ECDM and for ensuring machining precision. This study aims to experimentally investigate the impact of various types of electrolytes and their concentrations. These are divided into two categories: neutral solutions, which include sodium nitrate (NaNO₃) and sodium chloride (NaCl), and alkaline solutions, comprising sodium hydroxide (NaOH) and potassium hydroxide (KOH), as well as a mixture of both NaOH and KOH. The evaluation metrics considered include the Material Removal Rate (MRR), Tool Wear Rate (TWR), overcut (OC), Heat Affected Zone (HAZ) and surface quality. It was observed that alkaline solutions, particularly the mixed electrolyte, resulted in higher MRR and HAZ, reduced TWR, and the production of micro-holes with minimized overcut compared to using KOH and NaOH separately or neutral solutions, while also enhancing surface quality. Further analysis using Scanning Electron Microscopy (SEM) images and Energy-Dispersive Spectroscopy (EDS) of the brass tools used with different electrolytes revealed that tools used in KOH and mixed electrolytes exhibited less wear and material erosion compared to those used in NaOH and neutral solutions.

Sustainable Electrochemical Mechanical Polishing (ECMP) for 4H-SiC wafer using chemical-free polishing slurry with hydrocarbon-based solid polymer electrolyte

Large-diameter single-crystal silicon carbide (SiC) wafers with good surface quality are desirable to dramatically improve the performance of SiC-based power electronic devices. However, the preparation of such wafers using a strong oxidative polishing slurry has the limitations of low material removal rate (MRR) and high environmental impact. Electrochemical–mechanical polishing (ECMP) initiates surface removal by electrochemical oxidation without using harsh chemicals, making it an alternative with low environmental impact to conventional polishing. Herein, we propose the use of polystyrene sulfonic acid (PSS), a hydrocarbon-based polymer electrolyte without perfluoro compounds, for ECMP. The SiC surface was effectively oxidized by ECMP using PSS. The effects of the polyelectrolyte crosslinking treatment on the lifetime of polyelectrolyte-incorporated nonwoven cloths were investigated. The optimum electrolytic and mechanical conditions yielded high MRRs of 37 and 14 µm/h for 2- and 4-inch SiC wafers. Moreover, the surface morphologies of the growth face and nonfacet areas was discussed. The wafer-scale evaluation demonstrated the roughness reduction to 0.85 nm Sa (average) after 15-min ECMP of the 4-inch wafer. The polishing-induced residual stress was investigated using microscale and wafer-scale Raman mapping. Overall, the proposed ECMP process offers significant advantages in terms of speed, cost-effectiveness, and environmental impact.

Model for designing process strategies in ultrafast laser micromachining at high average powers

The great potential to scale the productivity of laser micromachining processes offered by the development of ultrafast lasers with average powers exceeding 1 kW comes at the cost of new physical and technical challenges. The large number of adjustable parameters, the different physical process limits, and the various possible optimization strategies complicate the design of suitable laser micromachining processes that enable high quality and high throughput.In this contribution, a comprehensive model is proposed that helps to identify the optimization strategies and process parameters required for the scaling of laser micromachining to high throughput at high average laser power without exceeding the process limits to ensure high surface quality.The model was experimentally verified on the example of laser micromachining of pockets in metals and silicon using an ultrafast laser with an average power of 1.01 kW, a pulse duration of 600 fs, different pulse energies, pulse bursts, and beam diameters. As a result, high material removal rates exceeding 120 mm3/min were achieved for silicon, stainless steel, copper, and aluminum, which exceed previously achieved removal rates by one to two orders of magnitude. The machined surfaces exhibit high quality as confirmed by the low measured roughness of about 1 µm.

Machining Performance Analysis of Ti6-Al-4V in Powder-Mixed EDM Using Green Dielectric Oil

In this investigation, the factors were oil type ([Formula: see text]), powder type ([Formula: see text]), and powder concentration ([Formula: see text]) level, and the machining parameters were the voltage (V), capacitance (pf), pulse-on time ([Formula: see text]), and pulse-off time ([Formula: see text]). The output parameters were the material removal rate (MRR), and tool wear rate (TWR). Three types of oils and powders, along with their respective particle concentrations, were selected for this experiment. Neem, Karanja, and sesame oils were mixed with aluminum oxide (Al2O3), chromium (Cr), and nickel (Ni) powder at 4, 6, and 8[Formula: see text]gm/l, respectively, using an overhead stirrer to investigate the conditions under which the green oil powder mixed mixture yielded a higher MRR and lower TWR during the micro-EDM process of titanium alloy (Ti-6Al-4V) using a 0.8[Formula: see text]mm tungsten carbide (WC) tool with fixed machining parameters (240[Formula: see text]V, 100[Formula: see text]pf, 20[Formula: see text][Formula: see text]s [Formula: see text], and 5[Formula: see text][Formula: see text]s [Formula: see text]). All the powders used in this experiment had a 32-micron (450 mesh) size. The Taguchi L[Formula: see text] orthogonal array and grey relational analysis methods were used to design and optimize the input process parameters for both responses. SEM, optical microscopic analysis, and EDS analysis were performed to examine the surface morphology, characteristics of the WC tool, and elemental composition of both the tool and the workpiece material. The optimum conditions for Karanja oil with a Cr powder mixture concentration of 4[Formula: see text]g/l resulted in higher MRR and lower TWR. However, machining with neem and sesame oils resulted in higher TWR and lower MRR.

Experimental Research of Ultrasonic Cavitation Evolution Mechanism and Model Optimization of RUREMM on Cylindrical Surface

Micro-pits are widely used in the aerospace and tribology sectors on cylindrical surfaces and electrochemical micromachining which are of great significance for the high material removal rate, absence of tool wear, and mechanical stress, while facing significant challenges such as stray corrosion and low machining efficiency. Aiming at the above problems, this paper proposes a comprehensive method called radial ultrasonic rolling electrochemical micromachining (RUREMM) in which an ultrasonic field has been added onto the cylindrical surface. First, a theoretical model was created to gain the rules of the formation and collapse of bubbles in the liquid medium. Second, to analyze the optimal size of the cathode electrode, the COMSOL5.2 simulation software was proposed to research the influence of the electric field on the different dimensions, and the influences of different parameters in RUREMM on material depth/diameter ratio and roughness are explored through processing experiments. Research results found that the cavitation bubble undergoes expansion, compression, collapse and oscillation, where the max deviation is less than 12.5%. The optimized size was chosen as 200 × 200 μm2 and an electrode spacing of 800 μm through a series of electric field model simulation analyses. Relevant experiments show that the minimum pits with a width of 212.4 μm, a depth of 21.8 μm, and a surface roughness (Ra) of 0.253 μm were formed due to the optimized parameters. The research results can offer theoretical references for fabricating micro-pits with enhanced surface quality and processing precision on cylindrical surfaces.

Defect-free grinding of silicon nitride at high material removal rate

Owing to the extreme hardness and toughness of sintered silicon nitride (Si3N4), the material is used in high stress and/or temperature applications such bearings, turbines, and combustion engines. Unfortunately, the same properties which make it ideal for use also make it particularly difficult to machine -- microcracks, inclusions and spalling are all common. While prior research has shown that it is possible to grind sintered Si3N4 without inducing surface damage so long as material is removed entirely under ductile flow, but grind forces associated with ductile Si3N4 material flow are so small as to render the material removal rate (MRR) impractical. Prior researchers have attempted to solve the MRR problem through laser-assisted machining. Laser ablation, by inducing a steep thermal gradient, weakens material through surface and subsurface cracks. Grinding of fractured weakened Si3N4 has been done at upwards of 50 % higher MRR. There are, however, issues with laser ablation, which prevent its widespread use. Laser ablation severely disrupts the microstructure of Si3N4. Because cracks propagate along and through grain boundaries, the irregular morphology makes accurately predicting crack growth from ablation and during subsequent grinding highly problematic. In this proof-of-concept work, researchers determined that it is possible to irradiation weaken Si3N4 without cracking it, and the material can be ground defect-free at a highly productive MRR. Findings suggest present laser-assisted machining methods which fracture weaken Si3N4 prior to grinding may not be the best way to maximize MRR.

Experimental Study of Electrical-Assisted Nanomachining of Monocrystalline Copper Using Customized Tungsten Tip

As a promising micro/nanofabrication method, electrical-assisted nanomachining has obtained substantial attention due to its high material removal rate and attainable superior surface quality. In this study, a rectangular wave electrical signal was applied for nanomachining by a customized tungsten tip. Owing to the coupling effect between the electric field and mechanical force, the cutting depth of the machined grooves can be expanded. In electrical-assisted groove processing, a depth of 270 nm and an aspect ratio of 0.6 on the copper sample can be achieved. The influence of operation parameters including applied voltage, frequency, duty ratio, normal force and cutting speed on the machining performance was investigated in terms of the groove depth, width, aspect ratio, and surface roughness. The potential machining mechanisms should be a combination of electric field force, nanoscale electric discharge, electric contact thermal effects, possible annealing behavior, and scraping and plowing actions induced by mechanical forces.

Effect of grinding parameters and coolants on grindability of Ti grade 9 alloy

For many years, surface roughness has drawn considerable attention, and it is a crucial design element in a variety of circumstances, including components sensitive to fatigue stresses, precision fittings, fastener holes, and aesthetic demands. Grinding the is best conventional machining process to achieve a better surface finish on a given component. Titanium 3Al-2.5 V or Ti grade 9 alloy is primarily utilized in the biomedical, aerospace, and automotive sectors. But because of its low heat conductivity, high chemical reactivity and rapid work hardening, this alloy is known as a difficult-to-cut material. In grinding, the abrasives have low thermal conductivity and small chip sizes, which in turn more heat to being focused in the cutting zone. This heat harms the surface of the workpiece. Therefore, it's crucial to regulate the quantity of heat that the workpiece receives.In this context, this work examines the surface quality of the Titanium 3Al-2.5 V alloy following surface grinding with an Al2O3 wheel under various grinding settings, including surface roughness (Ra), microhardness and material removal rate (MRR) from the workpiece. Techniques for delivering coolant conventionally (flood coolant), dry and using MQL were used and grinding performance were evaluated. The findings demonstrated that the Ra varied from 0.32 to 0.594 µm and hardness on the machine surface varied from 61.7 to 72 HRC. The MRR varied from 0.09 to 0.42 g/minute for the changes in depth of cut, table feed and coolants. Overall, the MQL has produced a good surface finish, high MRR and moderate hardness on the workpiece.

Generation of array of square microcavity on quartz by ultrasonic micromachining process utilizing developed micro tool

Quartz possesses distinct characteristics such as exceptional hardness, high brittleness, non-conductivity, remarkable corrosion resistance, efficient transmission within specific wavelengths, strong electrical insulation properties, and the ability to withstand high temperatures and thermal shocks. These extraordinary attributes have led to its component in a wide range of applications, including the fabrication of microelectronic chips, biochips, biological channels, microfluidics, optical lenses, beam-splitting lenses, etc. Ultrasonic micromachining (USMM) is a highly promising technique within the realm of micromachining to create micro features on quartz surfaces. In the present research, array of square micro tools has been designed and developed by the wire-electrical discharge machining (EDM) process. By utilizing the developed array of square micro tools, microcavity arrays have been generated by the USMM process. The influences of process parameters on material removal rate (MRR), width deviation (WD), angular deviation, and taper of square microcavities have been investigated in the present research work. The higher MRR is obtained as 1.427 mm3/min at higher abrasive slurry concentration and lower WD of micro cavities is obtained as 37 µm and lower taper angle is 1.109° at 5% abrasive slurry concentration. The lower value of angular deviation is obtained as 0.836° at a lower power rating during the generation of an array of square microcavity on quartz by the USMM process. By employing array of micro tools, the accuracy of micro features can be improved, and also productivity can be increased.

Исследование электроэрозионной обработки криогенно обработанных бериллиево-медных сплавов (BeCu)

Introduction. In modern manufacturing world, industries should adapt technological advancements for precision machining of difficult-to-machine metals, especially for beryllium copper (BeCu) alloys. The electrical discharge machining of alloys has proven its viability. The purpose of the work. A literature review indicated that the investigation of electrical discharge machining of BeCu alloys is still in its infancy. Furthermore, the cryogenic treatment of workpieces and electrodes in electrical discharge machining has not received much attention from researchers. Moreover, the impact of magnetic field strength on surface integrity and productivity during electrical discharge machining has not attracted much attention from researchers. The methods of investigation. This paper describes the use of electrolytic copper with different gap current values, pulse on periods, and external magnetic strength for electrical discharge machining of BeCu alloys. This paper examines how the material removal rate, the thickness of the white layer, and the formation of surface cracks are affected by cryogenic treatment of the workpiece and tool, pulse-on time, gap current, and magnetic strength. Results and Discussion. The combination of the cryogenically treated BeCu workpiece and the untreated Cu electrode had the highest material removal rate among all the combinations of workpieces and tools used in this study. The pulse on-time and the strength of the magnetic field had little influence on material removal rate, whereas the gap current had the greatest effect. The maximum achieved material removal rate was 11.807 mm3/min. At a high material removal rate, the observed thickness of the white layer on the horizontal surface ranged from 12.92 µm to 14.24 µm. In the same way, the maximum and minimum values for the vertical surface were determined to be 15.58 µm and 11.67 µm, respectively. According to scanning electron microscopy, the layer thickness was less than 20 µm, and barely noticeable surface cracks were observed in specimens with low, medium and high material removal rates. Obviously, due to the cryogenic processing of the workpiece and the external magnetic strength, there was a slight cracking of the surface and the formation of a white layer.

Investigating damage mechanisms of honeycomb cores machined with PCD circular saw blades

Aluminum honeycomb core (AHC) is extensively applied in aerospace and transportation industries for its exceptional strength-to-weight ratio. However, the unique structure of AHCs limits their manufacture. In this research, the damage mechanism of AHCs is firstly studied with polycrystalline diamond (PCD) circular saw blades to provide high-quality AHCs for wide-format honeycomb composites. The study meticulously examines the various forms of sawing damage incurred by AHCs at different material removal rates (MRR) and categorizes them accordingly. The results show that burrs of AHCs change from tiny blocks to larger strips with the MRR. At high MRR, the predominant failure modes include collapse, deformation, and hot cracking, while at low MRR, AHCs mainly suffer from cracking, micro-collapse, and oxidation by SEM and EDS analysis. A dynamic analytical model of the sawing angle is proposed based on the sawing trajectory to elucidate vibration scratching and burr formation. The effect of the sawing angle is quantified by the deformation displacement and damage area by the optical measurement. The microscopic reciprocating vibration scratching of AHCs is interpreted by the blade’s vibration state. The causes of sawing damage at different MRRs are investigated, indicating that at high MRR, the increased impact of the sawtooth leads to severe vibration scratches, collapses, and strip burrs, whereas, at low MRR, the high-frequency scratching of the sawtooth tends to result in tearing and micro-collapses. A comprehensive description of burr formation is presented by a 3D finite element model. Additionally, the cutting heat is the main cause of the oxidation of sawing surfaces by EDS. This systematic investigation analyzes and explores the sawing damage mechanisms of AHCs, offering in-depth insights for optimizing the sawing process to eliminate surface quality problems and improve the sawing efficiency and accuracy of wide-format AHCs.

Multi-Objective Optimization of Cutting Parameters for Polyethylene Thermoplastic Material by Integrating Data Envelopment Analysis and SWARA-Based CoCoSo Approach

This paper presents a comprehensive study on the multi-objective optimization of cutting parameters for Polyethylene (PE) thermoplastic material utilizing a CO2 laser. Recognizing the pivotal role of precise and efficient cutting in various sectors, from packaging to biomedical engineering, we integrate two potent analytical methodologies - Data Envelopment Analysis (DEA) and Step-Wise Weight Assessment Ratio Analysis (SWARA)-based Comprehensive Criteria Score Optimization (CoCoSo) approach. The cutting parameters chosen for the study were material thickness, power, and cutting speed. The experiments were conducted according to the Taguchi L18 orthogonal array. Measurements of surface roughness and kerf width were performed to examine the cutting quality. Additionally, another response variable, material removal rate, was calculated. By integrating Data Envelopment Analysis and SWARA-Based CoCoSo approach, the experimental condition that yielded the lowest surface roughness, kerf width, and the highest material removal rate was determined. The optimum experimental condition was found to be 4 mm material thickness, 80 W laser power, and 15 mm/s cutting speed. This work, therefore, paves the way for the innovative application of these combined methodologies in enhancing the production processes of PE and other thermoplastic materials, with clear implications for cost-effectiveness and sustainability in the manufacturing sector.

Atomic surface induced by novel green chemical mechanical polishing for aspheric thin-walled crucibles with large diameters

Aspheric thin-walled crucibles with large diameters are widely used for photovoltaics and semiconductor industries, while they have hard-brittle and aspheric characteristics. Nevertheless, these crucibles strictly require atomic surfaces and high material removal rate (MRR). This is a challenge for chemical mechanical polishing (CMP). To break this challenge, a novel green CMP was developed for fused silica, containing ceria, lanthana, hydrogen peroxide, diethylene triaminepentaacetic acid pentasodium, carboxymethyl cellulose sodium and guanidine carbonate. After CMP, surface roughness Ra of 0.115 is obtained at a scanning area of 5 × 5 μm2 measured by atomic force microscopy, and MRR is 563 nm/min. In such an atomic surface, the MRR is the highest compared with those published previously. Transmission electron microscopy confirms that the thickness of damaged layer after CMP is only 2.63 nm. A novel approach of robot floating polishing is proposed for aspheric crucibles with a diameter of 810 mm and a height of 580 mm. Using the developed CMP, surface roughness Sa of 0.178 nm on inner surface of an aspheric thin-walled crucible is achieved under a measurement area of 50 × 50 μm2. X-ray photoelectron spectroscopy (XPS) and electron paramagnetic resonance reveal that the content of Ce3+ increased from 28.54 to 43.76 %. Through Raman, XPS and Fourier transform infrared spectroscopy, CMP mechanisms are elucidated. Densified damaged layer on the surface of fused silica was induced by the transformation of surface structure from six-membered to four- or three-membered network. Ce-OH and Si-OH were formed between fused silica and ceria abrasives, forming Ce-O-Si by condensation reaction of dehydration. The developed green CMP and approach provide new pathway to polish and manufacture atomic surfaces for aspheric thin-walled crucibles with large diameters.

Nonlinear optical effects in polycrystalline transparent Al2O3 ceramics using femtosecond laser pulses—supercontinuum generation and laser damage

Nonlinear optical properties play a key role in technologies such as broadband laser light sources and ultrafast laser machining. With the emergence of transparent nanocrystalline Al2O3 ceramics as an alternative to single crystal alumina (sapphire), it is critical to understand their nonlinear optical behavior. Here, we report the demonstration of supercontinuum generation in polycrystalline alumina ceramics. Substantial broadening was observed when a focused 515 nm pulsed (260 fs) laser propagated through the ceramic sample. The broadening increased with increasing laser power and displayed stokes/anti-stokes asymmetries. At higher incident power, permanent damage was observed. Our results show that transparent nanocrystalline Al2O3 ceramics have a higher material removal rate than single crystal alumina. These results have interesting implications for laser machining as well as integrated photonics.

Analisis Pengaruh Parameter Terhadap MRR Pada Benda Kerja di Mesin CNC Turning dengan Metode Taguchi

A high material removal rate is one of the goals to be achieved when machining parts with CNC turning. However, slow processing affects product processing time and increases production costs. To overcome this problem, it is necessary to set the correct process parameters so that they provide the most influential contribution to the MRR and produce maximum parameter values. This research aims to determine the influence of parameters (spindle speed, feed speed, and feed depth) on MRR and to determine the correct process parameter settings to produce maximum MRR, namely in this experimental design using an orthogonal array L9 (33) with three replications. The material used is ST-60 steel, with the data analyzed using the Taguchi Larger Is a Better method in analysis software. From the results of the mean factor calculation, the percent contribution to feeding was found to be 19.53%, while the depth of feeding was found to be 64.56%. The optimum MRR value is obtained from a combination of parameters in the CNC Turning process on ST-60 steel which can make the response value optimally obtained at the spindle speed 3,184 [rev/min], feeding 0.22 [mm/rev] and depth of cut 2.5 [mm].

Mechanism of friction-induced chemical reaction high-efficient polishing single crystal 4H-SiC wafer using pure iron

This paper proposes a novel method for friction-induced chemical reaction machining of single-crystal 4H-SiC wafers using pure iron. Material Removal Rate (MRR) and surface quality of single-crystal 4H-SiC were studied, and the results demonstrate that both high surface quality and high MRR (Ra: 2.2 nm, MRR: 375 nm/min) were obtained. The mechanism of material removal during friction was investigated by examining the critical roles of friction speed. Solid-state chemical reactions between metal and SiC surfaces can be induced by friction, and the subsequent removal of reactants, resulting in a near-damage-free machined surface. A removal mechanism model of friction was established, which reveals that both the rates of solid-state reaction and reactant removal significantly impact the final removal rate of friction.

Cutting edge preparation of micro end mills by PVD-etching technology

Micromilling tools face significant challenges in achieving cutting edge preparation by mechanical processes due to their small size. To address these limitations, a new approach for cutting edge preparation of micro end mills by physical vapor deposition (PVD) etching technology is presented. By adapting the etching strategy, which is conventionally used as pre-treatment process for PVD technology to clean and condition the surface of cemented carbide substrate, cutting edges of micromilling tools were successfully modified. The high-energy process variation by Advanced Arc-Enhanced Glow Discharge (AEGD) offers the possibility of achieving high material removal rates on the tool surfaces and thereby altering the cutting edge geometry. Fundamental investigations on material removal as well as on the effects on surface topography, sub-surface properties, and coating adhesion of a subsequently applied PVD coating are performed. To influence the topography and the cutting edge geometry, the preparation time tp and bias voltage UB were selected. Subsequently, the machining performance of the modified tools is evaluated in a micromilling process of the hardened powder-metallurgical high-speed steel AISI M3:2 with a hardness of 62 ± 1 HRC. For this purpose, micro end mills of cemented carbide with a diameter of D = 1 mm were conditioned, achieving asymmetric geometric properties of cutting edges with varying average cutting edges rounding of S¯\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$${\\overline S}$$\\end{document}= 5.8 … 14.8 µm and a form-factor of K = 2.0 … 2.7. Based on the application tests a positive influence on the process forces was found. Thus, an efficient approach to cutting edge preparation can be identified by specifically designing ion etching in the PVD coating process.