High Flux Research Articles

High-performance COFs composite nanofiltration membrane fabricated by organobase catalyst

Covalent Organic Frameworks (COFs) composite nanofiltration (NF) membrane has high permeation flux and rejection. However, the reaction rate of COFs is relatively slow. Adding acid catalyst is a common method to shorten reaction time. However, the dissatisfactory synthesis rate will lead to irregular structure of COFs materials. In this work, it is the first time to use organobase as a catalyst to prepare COFs composite membrane. The COFs structure will be optimized and the membrane performance can be enhanced. The prepared TpPa-PIP membrane compared with acid catalyzed TpPa-HAc membrane has better permeability, permeance of 89 L m−2·h−1·bar−1 and CR rejection of 99.54 %. This improvement is because of the TpPa-PIP intermediate made slower reaction speed that improves the overall regularity and crystallinity of COFs. Therefore, it is better method for broadening the application of organobase-catalyzed in preparing membranes.

Photosensitive and high temperature resistant polyamide composite nanofiltration membranes with high flux and stable retention

Currently, most commercial membranes are used at temperatures below 50 °C. For high temperature water treatment, nanofiltration membranes with good thermal stability are highly sought after. In order to construct a novel polyamide thin-film composite nanofiltration (TFC NF) membrane, Congo red (CR) as monomer was introduced to the aqueous phase and the chemical structure of the selective layer was changed. Next, a thorough investigation was conducted into the impacts of the piperazine (PIP) to CR ratio on the surface morphology, separation efficiency and chemical structure of the membranes. The TFC NF membrane prepared after parameter optimization exhibited high retention (Na2SO4, >98 %) and flux up to 30 L·m−2·h−1·bar−1 at room temperature. Moreover, the Na2SO4 retention of the TFC NF membrane decreased by less than 1 % when used at 90 °C, demonstrating excellent heat resistance. Meanwhile, the incorporation of CR allowed the structure of the TFC NF membranes to be altered under UV irradiation conditions, which provided new insights into the optical modulation of the composite membrane properties. A promising and reproducible methodology for the development of high flux TFC NF membrane with thermal stability was offered, achieving a breakthrough in water treatment technology under high-temperature conditions.

Quantifying the High Early Solar Cosmic-Ray Flux with Cosmogenic Neon Isotopes in Refractory Minerals

An enhancement in the activity of the early young Sun resulting in a high charged particle flux has been invoked to explain excesses in spallation-induced nuclides in primitive planetary materials. Astronomical observations of energetic outbursts of young stellar objects (YSOs) also support the idea of an active young Sun. However, the early solar cosmic-ray (SCR) flux has not been well constrained. Here we use measured concentrations of SCR-produced nuclides that formed and are preserved in meteoritical hibonite and spinel, some of the solar system’s oldest solids, and physical models for dust transport in the early protoplanetary disk to determine the magnitude of the early SCR flux. We focus our attention on cosmogenic neon, which cannot have been inherited from precursors and can only be produced in situ in solids. Our modeled effective exposure time to SCRs for these solids is very short, on the order of years. This indicates that the young Sun’s SCR flux recorded in refractory mineral hibonite was up to ∼7 orders of magnitude higher than the contemporary level. Our flux estimate is consistent with the >105× enhanced flux inferred from astronomical observations of greatly enhanced flare activities of YSOs.

Tailoring the characteristics of polyacrylonitrile nanofiltration membranes for nickel removal from wastewater: The influence of binary solvents and pore-forming agents.

This work presents the results of an investigation on the physiochemical and structural characteristics of polyacrylonitrile (PAN) nanofiltration (NF) membranes prepared using a novel concept of binary solvents for nickel (Ni) removal from wastewater streams. The thermodynamic and kinetic aspects are emphasized aiming to optimize dope formulation, membrane performance, and durability. The fabricated membranes were characterized by scanning electron microscopy (SEM), porosimetry, tensile stress/strain, and flux and rejection. Results revealed that the use of an equal (1:1) mixture of n-methyl-2-pyrrolidone (NMP) and dimethylformamide (DMF) as dope solvents led to the formation of membranes with enhanced performance, offering pure water flux of 2.33 L·m-2·h-1·bar-1 and Ni rejection of 90.84%. Moreover, the incorporation of 0.5wt.% PEG as a pore-forming agent to the dope solution further boosted pure water flux to 4.97 L·m-2·h-1·bar-1 with negligible impact on Ni rejection. Besides attractive performance, the adopted strategy offered membranes of exceptionally high flexibility with no sign of defect or failure especially during module fabrication and testing enabling smooth and hassle-free scale-up and extension to other applications. PRACTITIONER POINTS: Optimized solvent mixture: A 1:1 blend of n-methyl-2-pyrrolidone (NMP) and dimethylformamide (DMF) as solvents resulted in enhanced membrane performance. High flux and Ni rejection: The fabricated membranes exhibited a pure water flux of 2.33 L·m-2·h-1·bar-1 and a remarkable Ni rejection of 90.84%. PEG enhancement: Incorporating 0.5wt.% PEG as a pore-forming agent further improved the membrane's pure water flux to 4.97 L·m-2·h-1·bar-1, without compromising Ni rejection. Exceptional flexibility: The adopted strategy yielded membranes with exceptional flexibility, making them suitable for scale-ups and other applications.

Climate Bistability at the Inner Edge of the Habitable Zone due to Runaway Greenhouse and Cloud Feedbacks

Understanding the climate dynamics at the inner edge of the habitable zone is crucial for predicting the habitability of rocky exoplanets. Previous studies using global climate models (GCMs) have indicated that planets receiving high stellar flux can exhibit climate bifurcations, leading to bistability between a cold (temperate) and a hot (runaway) climate. However, the mechanism causing this bistability has not been fully explained, in part due to the difficulty associated with inferring mechanisms from small numbers of expensive numerical simulations in GCMs. In this study, we employ a two-column (dayside and nightside), two-layer climate model to investigate the physical mechanisms driving this bistability. Through mechanism-denial experiments, we demonstrate that the runaway greenhouse effect, coupled with a cloud feedback on either the dayside or nightside, leads to climate bistability. We also map out the parameters that control the location of the bifurcations and size of the bistability. This work identifies which mechanisms and GCM parameters control the stellar flux at which rocky planets are likely to retain a hot, thick atmosphere if they experience a hot start. This is critical for the prioritization of targets and interpretation of observations by the James Webb Space Telescope. Furthermore, our modeling framework can be extended to planets with different condensable species and cloud types.

Catalytic effects of transition metal oxides on HTPB-based fuel polymer matrices

Low regression rate due to difficult pyrolysis is a major challenge in the practical application of terminated hydroxyl‑terminated polybutadiene (HTPB)-based fuels in hybrid rocket propulsion. Accelerating the decomposition of the polymer matrix is an effective method to improve the regression rate of HTPB fuels. To determine the difference in combustion performance between different transition metal oxides loaded HTPB-based fuels, nickel oxide (NiO), ferric oxide (Fe2O3), copper oxide (CuO) and manganese dioxide (MnO2) were introduced into the HTPB matrix at 5% mass fraction. The experimental results showed that the metal oxides could significantly catalyze the pyrolysis of HTPB-based fuels and enhance the fuel regression rate, and the catalytic effect was mainly concentrated in the middle and late stages of the thermal decomposition process of polybutadiene components. Among the four transition metal oxides, CuO and MnO2 showed better catalytic effects on the combustion performance of HTPB-based fuels in the high oxygen mass flux region, while NiO showed better catalytic effects in the low oxygen mass flux region. The present study compares the regression rate of fuel grains modified with different transition metal oxides, which provides a basis for the selection of future catalysts, verifies the catalytic effect of the transition metal oxides on the combustion of HTPB-based fuels and further analyzes the combustion reaction mechanism of the fuels.

Turbulent pipe flow and heat transfer of a binary mixture at supercritical pressure: Influences of cross-diffusion effects

Cross-diffusion effects, including Soret and Dufour effects, are enhanced around the pseudo-critical temperature (Tpc) of a binary mixture. Their influences on heat transfer at supercritical pressure have been scarcely studied. To bridge this gap, large-eddy simulations (LES) are conducted to investigate forced convective heat transfer of a CO2–ethane mixture at supercritical pressures in a circular pipe subject to a uniform heat flux. Both heating and cooling conditions, along with varying initial concentrations and thermodynamic pressures, are included in the simulations. The LES results reveal that the Soret effect causes concentration separation, resulting in a concentration boundary layer. The magnitudes of the thermodiffusion factor (kT) and the radial temperature gradient control the intensity of separation, which is more pronounced at near-critical pressure and high heat flux. Since kT is significant only around Tpc, downstream decay of the concentration separation is observed as the loci of T=Tpc migrate away from the wall so that the local radial temperature gradient diminishes. The primary factors affecting heat transfer are the variations in thermal conductivity and isobaric specific heat resulting from concentration separation. In contrast, the Dufour effect and the accompanying inter-diffusion play negligible roles. In deterioration scenarios, the bulk Nusselt number (Nub) shows a maximum relative drop of 8%, whereas in enhancement scenarios, Nub shows a maximum relative increase in 10%, with both deterioration and enhancement decaying downstream. Cross-diffusion effects have negligible impacts on density and streamwise velocity, but noticeably alter streamwise velocity fluctuation and turbulent kinetic energy.

Precursor boundary layer conditions for shallow and deep convection: inferences from CAIPEEX field measurements over the Indian Peninsula

The diurnal cycle of environmental conditions for shallow and deep convection regimes within the Indian monsoon environment is investigated using comprehensive observations from the surface, boundary layer, and cloud layers. For shallow convection (SC) and deep convection (DC) in the afternoon hours, thermodynamics, moisture convergence, and several other environmental variables provide information on the factors that control the vertical extent of convection in both regimes. The SC regime is characterized by high sensible heat flux, leading to stronger boundary layer turbulence, a higher mixed layer, and increased dry air entrainment from the free troposphere. Evaluation of several pre-conditioning parameters with T-test statistics suggests that stronger mid-level meridional wind shear and lack of mid-level moistening are detrimental to the growth of clouds in the SC regime. Conversely, the DC regime is driven by low surface fluxes and low surface-level buoyancy, with higher boundary layer and mid-layer moisture and more mid-layer instability, supporting larger Convective Available Potential Energy (CAPE). Morning precursor conditions for the preference of SC versus DC regime in the afternoon reveal that total column water vapor, relative humidity and CAPE are significantly higher on DC days. Large-scale moisture transport in the early morning within and above the boundary layer, driven by stronger westerly winds, is a key factor for the development of DC later in the day. This investigation enhances our understanding of boundary layer controls on shallow and deep convection within the Indian Monsoon environment.

CO2 retention in high-pressure/high-temperature reservoirs of the Yinggehai Basin, northwestern South China Sea

Global industry drillings targeted at deep-burial hydrocarbons have renewed the record of maximum sustainable overpressure in sedimentary basins. However, the influence of extremely high overpressure on natural fluid accumulation and artificial waste sequestration is not yet completely understood. To better understand the motion characteristics of the highly overpressured CO2-rich fluid, the CO2 retention capacity was quantified, and the CO2-rich fluid motion trails were evaluated in an ideal natural laboratory in the Yinggehai Basin. The hydraulic sealing capacity was higher than the capillary sealing capacity in the highly overpressured stratum. Relative to the situations of no breach or solely breached by capillary failure, the superposition of capillary and hydraulic failures resulted in the caprock integrity breakage by faults (or fractures), diapirs, and pipes. Meanwhile, the high expulsion flux of CO2-rich fluid caused the consumption of chlorite to generate illite in the caprock of dual-breached fields. The CO2-rich fluid flux of capillary invasion was limited by the inherently low permeability of caprock, which may be insufficient for a dramatic change of hydrogen ions or electron activities to induce remarkable chlorite dissolution in the caprock of the sole-breached field.

Peripheral Blood Lymphocyte Subgroups in Patients Undergoing Hemodialysis with Medium Cutoff Membranes and High-Flux Membranes: THE SHE Continuation Study

Introduction: Chronic kidney disease (CKD) poses a significant global health burden, with increasing prevalence and high morbidity and mortality rates, particularly in end-stage kidney disease (ESKD). While traditional risk factors contribute, the exact mechanisms remain elusive, with inflammation playing a pivotal role. Medium cutoff (MCO) membranes offer promise in improving dialysis outcomes by efficiently clearing uremic toxins without substantial albumin loss. We aimed to elucidate the impact of MCO and high-flux (HF) membranes on peripheral blood lymphocyte subpopulations in hemodialysis patients. Methods: Twenty-four ESKD patients underwent 36 sessions each with MCO and HF membranes. Immunophenotyping by flow cytometry was performed to analyze lymphocyte subsets. Results: NK cell percentages significantly increased with MCO, returning to baseline with HF. Th1 cells decreased post-HF, while Th2 and Tfh cells increased with MCO and persisted. Treg cells remained stable with MCO but decreased with HF. Conclusion: MCO dialysis induced an anti-inflammatory shift, evidenced by increased Th2 and Tfh cells and stable Treg cells. NK cells also responded favorably to MCO. These findings underscore MCO membranes’ potential to modulate immune responses and improve patient outcomes in ESKD.

Developing high-flux dense Janus membrane with robust wetting and scaling resistance: A systematic comparison with Omniphobic membranes

Membrane wetting, scaling and low flux are challenging obstacles for membrane distillation (MD). However, the lack of advanced membranes capable of achieving both high flux and high wetting/scaling resistance constrains MD potential applications. Herein, a dense Janus membrane (JM) was facilely developed by co-depositing a dense PVA/PDA layer on a highly porous PTFE substrate to overcome this dilemma and systematically compared with omniphobic PTFE substrates with varied pore sizes for the first time. Results showed that, unlike flux-resistance “trade-off” observed for PTFE substrates, dense JM effectively resisted 0.4 mM SDS at a high flux of 56.8 LMH and retarded membrane scaling by 20 mM oversaturated gypsum. Robust wetting resistance was primarily attributed to the sieving effect of the sub-nanometer surface layer, which greatly protected substrate from SDS adsorption and feed intrusion, and was less affected by severe surface concentration polarization and relatively low substrate LEP than PTFE substrates. Strongly polar PVA/PDA layer provided a much more thermodynamically unfavorable continuous interface for gypsum adhesion than PTFE substrates, which played a key role in determining anti-scaling behavior. In contrast, gypsum still tended to rapidly cause membrane scaling in stagnant zones within PTFE substrates when flux was increased. This study shall provide new insights in designing high-performance membranes for robust hypersaline wastewater treatment, and highlighting dense JMs with a macroporous substrate and a highly hydrophilic dense surface layer as ideal alternatives.

Highly Anion‐Conductive Viologen‐Based Two‐Dimensional Polymer Membranes as Nanopower Generators

AbstractTwo‐dimensional polymers (2DPs) and their layer‐stacked 2D covalent organic frameworks (2D COFs) membranes hold great potential for harvesting sustainable osmotic energy. The nascent research has yet to simultaneously achieve high ionic flux and selectivity, primarily due to inefficient ion transport dynamics. This is directly related to ultrasmall pore size (<3 nm), much smaller than the duple Debye length in the diluted electrolyte (6–20 nm), as well as low charge density (<4.5 mC m−2). Here, we introduce a π‐conjugated viologen‐based 2DP (V2DP) membrane possessing a large pore size of 4.5 nm, strategically enhancing the overlapping of the electric double layer, coupled with an exceptional positive surface charge density (~6 mC m−2). These characteristics enable the membrane to facilitate high anion flux while maintaining ideal selectivity. Notably, V2DP membranes realize an impressive current density of 5.5×103 A m−2, surpassing benchmarks set by previously reported nanofluidic membranes. In the practical application scenario involving the mixing of artificial seawater and river water, the V2DP membranes exhibit a considerable ion transference number of 0.70 towards Cl−, contributing to an outstanding power density of ~55 W m−2. Theoretical calculations reveal the important role of the large quantity of anion transport sites, which act as binding sites evenly located in the positively charged N‐containing pyridine rings. These binding sites enable kinematic coupling and decoupling between anions and the V2DP skeleton, establishing a continuous Cl− ion transport pathway. This work demonstrates the great promise of large‐area ultrathin 2DP membranes featuring highly organized charged ion transport networks when applied for osmotic energy conversion.

A Planar-Cavity Receiver Configuration for High-Temperature Solar Thermal Processes

Next-generation concentrating solar thermal power (CSP) technologies target a wide spectrum of applications including electricity generation, thermochemical processes, and industrial process heat for broad decarbonization potential. Many of these applications require higher temperatures than those of current commercial nitrate salt systems. Particulate materials are promising candidates for next-generation high-temperature heat transfer and low-cost storage media and can facilitate operation over a wide temperature range. However these materials necessitate novel receiver configurations to accept the high incident flux concentrations that enable high solar-to-thermal receiver efficiency. One option is a novel light-trapping planar cavity receiver configuration in which small cavity-like structures are formed from opaque planar surfaces such that a high incident flux concentration at the cavity aperture is reduced to a wall-absorbed solar flux concentration that is manageable within limited wall-to-particle heat transfer rates. The paper introduces the receiver configuration and provides calculated optical performance for a preliminary 50 MWt receiver design.

Development of Readily Available & Robust High Heat Flux Gardon Gauges

Concentrated solar power (CSP) technologies deliver concentrated solar energy as a heat source to industrial processes, power generation cycles, and chemical cycles. CSP systems require accurate and reliable high flux measurements, and next generation CSP systems will require flux measurement up to 1000 W/cm2. Existing flux measurement devices do not comprehensively meet the flux rating, cycle life, cost, and lead-time needs of stakeholders, necessitating the development of an improved flux sensor. In this study, Sandia National Laboratories (SNL) partnered with Hukseflux Thermal Sensors to develop a low-cost, short lead-time, and robust flux sensor rated to 250 W/cm2. Three prototype circular foil gauge designs were assessed for performance at the National Solar Thermal Test Facility (NSTTF) at SNL. Each gauge design measured flux up to 250 W/cm2 with <5% measurement error. Following baseline error quantification, gauges were exposed to flux above 500 W/cm2 to assess gauge failure mechanisms. Gauges physically survived >500 W/cm2 flux exposure, but measurement error was found to increase after foil coatings reached 400 °C. The results of this study suggest that coating optical properties change at excessive temperatures and that foil coating temperature, rather than heat flux level, dictates the acceptable gauge measurement range.

Texture measurements of archaeological objects at STRESS-SPEC neutron diffractometer

The main advantage of neutron diffraction over X-ray diffraction, arises from the fact that the interaction of neutrons with material is relatively weak and not related to the number of electrons, and consequently the penetration depth of neutrons is about 102-103 larger than that of laboratory X-ray diffraction. This is particular essential for the non-destructive texture analysis of archaeological objects as no additional surface treatments of the samples (e.g. polishing) are necessary. STRESS-SPEC at MLZ is designed as a state of the art multi-purpose diffractometer for strain and texture analysis. Besides the optimized high neutron flux the available large variability in gauge volume definition systems together with the robotic sample handling option offer high flexibility for bulk or gradient texture measurements. Since 2014, local and bulk textures of iron and gold artefacts collected by Bavarian State Archaeological Collection (Munich, Germany) have been thoroughly investigated at STRESS-SPEC. Results showed that heat treatment of iron artefacts at high temperatures can re-orientate the inner crystallites. In the gold foil artefacts, the texture represented by the measured pole figures shows a high symmetry – the so-called Cube component, which is commonly found in annealed fcc materials. For comparison, laboratory samples were produced by rolling, flat hammering, and pin / round hammering and also measured in order to elucidate possible manufacturing and processing routes. In turned out that both rolling and pin / round hammering followed by a high temperature annealing can produce similar pole figures to those of the gold artefacts foils.

Phase stability and microstructure of neutron-irradiated substoichiometric yttrium dihydrides

The impact of the neutron-displacement damage on phase stability and microstructure of substoichiometric yttrium dihydrides (YHx, x <2) were investigated to assess their use as solid moderator in high-temperature nuclear reactors. YHx specimens were, thus, subjected to neutron irradiations in the range of 0.1–2 displacements per yttrium atom (dpa-Y) in the temperature range of 536–878°C at the Oak Ridge National Laboratory's (ORNL's) High Flux Isotope Reactor (HFIR). YHx specimens were initially prepared at stoichiometry (H/Y) ratios of 1.69 and 1.83. HFIR-irradiated specimens were characterized by variety of techniques to investigate H retention characteristics including dimensional analysis, optical microscopy, scanning electron microscopy electron back scatter diffraction (EBSD), transmission electron microscopy, thermal desorption spectroscopy (TDS), and high-energy x-ray diffraction (HE-XRD) characterizations. Overall, YHx exhibited notable structural and phase stability under short-term neutron-irradiation, except for the samples with significant silicon carbide (SiC) interaction at high doses and temperatures. Basic dimensional and mass measurements were misleading for accurate assessment of H retention, as confirmed by EBSD phase maps, XRD line profiles, and TDS signals. Thus, it was discussed that a robust H retention metric is needed to assess irradiated hydrides. Nanoscale cavities were observed as a result of the neutron irradiation in all samples. Although no clear impact of dose and irradiation temperature was determined, the initial H/Y ratio had an impact on the cavity number density where low H/Y specimens had high-resistance to cavity formation. The Y-vacancy cluster formation at the collision stage of the displacement cascade and their stabilization by H were considered to be the likely underlying mechanisms for the observed cavity microstructure.

Study of the fuel irradiation capsule using NEPTUNE_CFD software

The Fuel Irradiation Capsule (FUICA) is an experimental device designed to irradiate fuel elements in a Material Testing Reactor (MTR) during long period. This component is being studied for implementation in the Jules Horowitz reactor (RJH) under construction in France (1).Its function is to irradiate and to cool fuel sample on a passive way by transferring the thermal energy generated to the device periphery, through an annular zone of confined and pressure-regulated water (2). Its external wall, kept cold by the reactor cooling circuit, allows for the heat extraction. Natural convection is the driving force for the heat transfer between the fuel element and the cold wall of the device. By eliminating any internal forced convection cooling system, the device becomes relatively simple and cost-effective.This paper describes the device modeling carried out using the NEPTUNE_CFD software (3). The present work, in its first part, focuses on the behavior of the device depending on the heat flux, and in its second part, the sensitivity to boundary conditions. The objective is to provide a way to design and optimize the fuel capsule thermal characteristics. For that, an arbitrary size of fuel capsule is chosen in order to analyze the physics involved. A sensitivity study is then presented in order to highlight the influence of the physical parameters on the fuel capsule performance.Three operating ranges for the heat transfer are exhibited in this study: moderate in the liquid phase, the heat transfer becomes optimal in the two-phase regime, and even improves with the level of heat flux before deteriorating abruptly for high flux called Critical Heat Flux (CHF). Two observations also arise to improve thermal transfer: in the liquid phase, it is necessary to reduce the water thickness to improve convection, and in the two-phase regime, the heat transfer increases proportionally to the heat flux. In the end, the irradiation capsule is capable of extracting very high heat flux.

Two Models for the Orbital Modulation of Gamma Rays in Cyg X-3

We model the currently available γ-ray data on Cyg X-3 from the Fermi Large Area Telescope. Thanks to Cyg X-3’s very strong γ-ray activity during 2018–2021, the data quality has significantly improved. We study the strong orbital modulation of the γ-rays observed at high γ-ray fluxes. The modulation, as found earlier, is well modeled by anisotropic Compton scattering of the donor blackbody emission by relativistic electrons in a jet strongly misaligned with respect to the orbital axis. We confirm that this model fits well both the average γ-ray modulation light curve and the spectrum. However, we find that if the jet were aligned with the spin axis of a rotating black hole, it would undergo geodetic precession with a period of ∼50 yr. However, its presence is ruled out by both the γ-ray and radio data. Therefore, we consider an alternative model in which the average jet direction is aligned, but it is bent outside the orbit owing to the thrust of the donor stellar wind, and thus precesses at the orbital period. The γ-ray modulation then appears as a result of the variable Doppler boosting of synchrotron self-Compton jet emission. This model also fits the data well. However, the fitted bending angle is much larger than the theoretical one based on the binary and wind parameters as currently known. Thus, both models disagree with important aspects of our current theoretical understanding of the system. We discuss possible ways to find the correct model.

Large-Eddy Simulation Study of Flow and Combustion Dynamics in a Full-Scale Hydrogen-Air Rotating Detonation Combustor-Stator Integrated System

Abstract A first-of-its-kind large-eddy simulation (LES) study is conducted to numerically investigate the combustion dynamics as well as aero-thermal phenomena in a full-scale non-premixed hydrogen-air rotating detonation engine (RDE) integrated with nozzle guide vanes (NGV) acting as the turbine stator. The LES framework incorporates hydrogen-air detailed chemical kinetics and adaptive mesh refinement. A comparative analysis is carried out for two operating conditions with different fuel/air mass flow rates but global equivalence ratio of unity. The LES model is validated against experimental data with respect to detonation wave speed/height, wave dynamics, and axial static pressure distribution. Numerical results indicate significant deflagrative combustion occurring in the fill region near the inner wall due to formation of recirculation zones in the injection near-field driven by the backward facing step. The leading detonation wave is found to be trailed by an azimuthal reflected-shock combustion wave, which consumes unburned vitiated reactants that leak through the main detonation wave. The detonation wave characteristics do not change appreciably with the presence of NGV. The exit flow is found to be nearly fully subsonic and supersonic for the low and high mass flux conditions, respectively. The presence of NGV renders the flow more axial, and significantly impacts the exit Mach number and total pressure. The low mass flux operating point, despite exhibiting more deflagrative losses within the combustor, yields overall lower pressure drop from plenum to exhaust, mainly attributed to lower pressure drop across the injectors.

Oxidation two-dimensional porous carbon membrane for efficient and precise separation of mixed dyes solution

In actual production, dye wastewater typically contains a mixture of two or more dyes. Therefore, developing efficient and precise separation techniques for mixed dyes solution is of great value but still faces great challenges. In this study, we prepared two-dimensional porous carbon sheets (PCS) using Ti3C2 as the precursor through halogenation etching technology. Subsequently, the PCS was oxidized with nitric acid at room temperature to obtain oxidized porous carbon sheets (OPCS). When mixed dyes solution RB/MO and RB/MB were screened using OPCS vacuum filtration self-assembled porous carbon membrane (OPCSM), the rejection rate for the larger dye RB was 99.9 %, while the permeation rates for the smaller dyes MO and MB were 91.0 % and 99.5 %, respectively. Notably, OPCSM also exhibited much higher water flux than the previously reported. The combination of high water flux and precise screening make OPCSM a highly promising membrane for the separation and reuse of mixed dyes.