High-density Polyethylene Research Articles

Pengaruh Penambahan Cacahan Limbah Plastik HDPE (High Density Polyethylene) Sebagai Bahan Tambah Campuran Laston AC-WC (Asphalt Concrete-Wearing Course) Terhadap Karakteristik Marshall

In increase quality vulnerable roads in Indonesia damaged Because influenced by weather, water, load vehicle excess, and construction insufficient pavement​ fulfil requirements, required material add as much as you can increase strength and help repair construction road asphalt the Utilization material waste plastic in construction pavement become good alternative​ in in increase quality pavement road. Objective study This is For know How influence addition waste plastic type High Density Polyethylene (HDPE) against Marshall Laston AC-WC characteristics with variation rate HDPE plastic at 0%, 2%, 4%, and 6%. Marshall characteristics reviewed is mark density (density), VIM (void in mix), VMA (void mineral aggregate), VFA (void filled with asp halt), melting (flow), and stability. Method research used​ with method experiments in the laboratory and refers to Specification General Highways​ 2018. Research results shows the Marshall test on the mixture Laston AC-WC with addition rate HDPE plastic 0%, 2%, 4%, and 6% can be raise mark density (density), stability , VFA ( Void Filled with Asphalt), whereas For VIM (void in mix), VMA (Void Mineral Aggregate) and melt (flow) values experienced decline . Marshall parameter values obtained​​ fulfil standard Specification General Highways​ 2018. Percentage​ rate optimum asphalt (KAO) obtained is 6.0%, Marshall test of variation material plus waste plastic best value​ For density, melting (flow), stability, VIM , VMA, and VFA, namely at levels waste plastic 2%.

Improved thermal conductivity of high‐density polyethylene by incorporating hybrid fillers of copper powders and silicon carbide whiskers

AbstractIn this paper, highly electrically and thermally conductive copper powders (Cu) and electrically insulative yet thermally conductive silicon carbide whiskers (SiCw) were selected as functional fillers and high‐density polyethylene (HDPE) was used as the matrix to prepare thermal conductive composites. By controlling the amount of Cu at 30 vol% which is below percolation threshold, the volume resistivity of the composites is maintained above 1014 Ω cm. The results showed that SiCws entered the area which was not occupied by Cu particles and they played a bridging effect among Cu particles, thereby promoting the formation of intact thermal conductive pathways that contributed to improving the thermal conductivity of corresponding composites. The combination of SiCw:Cu = 3:1 at a filler content of 30 vol% resulted in a thermal conductivity as high as 1.921 W/mK, which is 380% higher than pure HDPE.

Enhancing PEHD pipes reliability prediction: Integrating ANN and FEM for tensile strength analysis

In the pipe industry, pressure pipes have long made use of High-Density Polyethylene (HDPE), which is used extensively. Currently, HDPE pipes are installed in higher numbers in comparison with other plastic pipes. The purpose of this study is to evaluate and compare the predictive capabilities of two methods, including the finite element method (FEM) and artificial neural network (ANN) techniques, for predicting the tensile strength of HDPE pipes used in water distribution systems. Attempts have been made to improve prediction models to better predict the mechanical behavior of these pipes by improving our understanding of the structure and surface characteristics as well as the interactions between the interface and the operating environment. The results show that experimental trial results are in perfect agreement with machine learning techniques. The findings of this study highlight the benefits of using ANN to predict the behavior of HDPE pipes, which may have significant ramifications for the plastics and water distribution industries.

Repercussion of fiber content on the mechanical, thermal, and thermomechanical properties of natural fibers reinforced thermoplastic composites for automotive application

Natural fibers are becoming very popular as a reinforcement in composite materials owing to their benefits, such as low-price, lightweight, availability, and environmental friendliness. In this study, abaca fiber-reinforced polypropylene (PP) and high-density polyethylene (HDPE) composites were created with the help of the injection molding method. Prior to composite fabrication, abaca fibers were chemically treated with a 5 wt% caustic soda (NaOH) solution to improve the bonding between the abaca fibers and the matrix and to enhance their properties. Scanning electron microscopy (SEM) was utilized to assess the fiber surface microstructures before as well as after the chemical treatment, along with the fractured surfaces of tensile specimens. The mechanical properties, such as tensile, bending, and impact strength, of abaca/PP and abaca/HDPE composites were evaluated and compared. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) methods were utilized to investigate the thermal behavior of composites. Also, the dynamic mechanical analysis (DMA) method was utilized to explore the thermomechanical properties of the fabricated composites. The outcomes of the experimental findings showed that abaca/PP composite with 10 and 20 wt% fibers is the best choice of material to be used in the automobile industry.

Microwave-assisted fabrication of high-strength natural fiber hybrid composites for sustainable applications: An experimental and computational study

The present study deals with the fabrication of hybrid composites using biodegradable and ecologically friendly natural fibers and a recyclable thermoplastic matrix. Pure and hybrid natural fiber composites of high-density polyethylene (HDPE) with Kenaf and Ramie fiber, 20 wt%, were fabricated using microwave-assisted compression molding. The composite's mechanical characterization was performed using tensile, flexural, impact, and hardness tests. X-ray diffraction was done to investigate the crystallinity percentage, and scanning electron microscopy of fractured surfaces was performed to determine failure mechanisms. The hybrid composite of HDPE/Ramie and Kenaf exhibited the highest ultimate tensile strength (UTS) at 29.3 ± 1.2 MPa, surpassing HDPE/Kenaf (21.6 ± 1.1 MPa) and HDPE/Ramie (24.3 ± 1.4 MPa) composites. In terms of flexural strength, HDPE/Ramie demonstrated the highest at 19.9 ± 1.5 MPa, while HDPE/Kenaf had the lowest at 18 ± 1.1 MPa. The hybrid composite's flexural strength was intermediate at 19 ± 1.3 MPa. Impact strength followed a similar trend, with the hybrid composite leading at 40.2 KJ/m2, followed by HDPE/Ramie (26.9 KJ/m2) and HDPE/Kenaf (12.3 KJ/m2). Hardness tests revealed the highest hardness in the hybrid composite and the lowest in HDPE/Kenaf. A computational study has been performed to develop a model for predicting the hybrid composites. A strong agreement between both studies has been observed. The developed composite is deemed suitable for various light-duty applications, such as roofing, car interior panels, and mobile covers, offering potential benefits in reducing carbon footprint.

Laboratory-Simulated Photoirradiation Reveals Strong Resistance of Primary Macroplastics to Weathering.

The photodegradation of macroplastics in the marine environment remains poorly understood. Here, we investigated the weathering of commercially available plastics (tabs 1.3 × 4.4 × 0.16 cm), including high-density polyethylene, low-density polyethylene, polypropylene, polystyrene, and polycarbonate, in seawater under laboratory-simulated ultraviolet A radiation for 3-9 months, equivalent to 25-75 years of natural sunlight exposure without considering other confounding factors. After the exposure, the physical integrity and thermal stability of the tabs remained relatively intact, suggesting that the bulk polymer chains were not severely altered despite strong irradiation, likely due to their low specific surface area. In contrast, the surface layer (∼1 μm) of the tabs was highly oxidized and eroded after 9 months of accelerated weathering. Several antioxidant additives were identified in the plastics through low temperature pyrolysis coupled with gas chromatography/mass spectrometry (Pyr-GC/MS) analysis. The Pyr-GC/MS results also revealed many new oxygen-containing compounds formed during photodegradation, and these compounds indicated the dominance of chain scission reactions during weathering. These findings highlight the strong resistance of industrial macroplastics to weathering, emphasizing the need for a broader range of plastics with varying properties and sizes to accurately estimate plastic degradation in the marine environment.

Functionalization of Artwork Packaging Materials Utilizing Ag-Doped TiO2 and ZnO Nanoparticles.

Most of the artworks stored in museums are often kept in inappropriate climatic and environmental conditions that facilitate the formation and growth of microorganisms, such as fungi, which are responsible for many types of biodegradation phenomena. To mitigate and prevent these deteriorative processes, functionalized packaging materials can be used for the storage and handling of artworks. The aim of this study was to develop a potential anti-biodeterioration coating suitable for packaging purposes. TiO2 and ZnO doped with different amounts of Ag (0.5 wt%, 1 wt%, and 3 wt%) were synthesized and dispersed in polyvinyl alcohol (PVA) and acrylic resin (Paraloid B72), then applied on different types of packaging materials (cellulose and the high-density spunbound polyethylene fiber Tyvek®, materials that are frequently used as packaging in museums). Analytical investigations (SEM/EDS, Raman, FTIR, and XRD) were employed to assess dispersion on the packaging material. Furthermore, resistance against biodeteriogens was assessed using Cladosporium sp., a bioluminometer, to define the biocidal efficacy.

The Long-Term Performance of a High-Density Polyethylene Geomembrane with Non-Parametric Statistic Analysis and Its Contribution to the Sustainable Development Goals

The tailings from gold beneficiation can cause various negative impacts, necessitating measures to prevent their transport and environmental contamination. Geomembranes serve as hydraulic barriers in mining tailings reservoirs, thereby supporting the Sustainable Development Goals (SDGs). To ensure that the geomembrane effectively mitigates environmental impact, it is essential to study its durability when applied in the field. This article examines the long-term performance of an HDPE geomembrane exposed for 7 and 11 years at a gold mining tailing site in Brazil. Samples were exhumed from different locations at the dam, and their properties were evaluated. Non-parametric statistics were employed using the Kernel Density Estimator (KDE). For the 11-year-old geomembranes, the probability of the geomembrane reaching nominal failure in terms of tensile strength was 0.4%. The peel separation values exceeded the maximum allowable by the GRI GM13 standard. Although the geomembranes showed significant antioxidant depletion, suggesting they were close to or had already reached their residual stages, they approached nominal failure based on their stress crack resistance but did not rupture. The environmental analysis indicated no significant contamination in the area, corroborating that the geomembrane is fulfilling its function. The non-parametric methodology proved promising for durability analysis and could be applied to other engineering projects with geosynthetics, thereby adding reliability to decision-making in alignment with sustainable development.

Sustainable composites with synergistic combinations of construction and demolition waste: Behavior of rubber, HDPE, PS, and brick after short-term water immersion

The growing concern for environmental sustainability and construction and demolition (C&D) waste management has led to innovative approaches to recycling and reusing these materials. This study presents the development of sustainable composites using a unique mix of C&D wastes: rubber, high-density polyethylene (HDPE), polystyrene (PS), and bricks. Mechanical tests were performed to determine their structural integrity and suitability for construction applications. The composites were further subjected to immersion in water to evaluate their resistance to environmental factors. In addition, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X-ray diffraction (XRD) analyses were performed to obtain information on the chemical and morphological properties of the composites. The synergy achieved by combining C&D waste materials such as rubber, HDPE, PS and bricks resulted in composites that exhibited outstanding mechanical properties. The samples with the composition rubber:HDPE:PS:brick = 15:40:40:5 immersed in water for 21 days presented the best mechanical resistance properties: Rc = 146.51 MPa, Ei = 36.05 kJ/m2, Rt = 11.2 MPa. The results demonstrated that the composites maintained their structural integrity and did not undergo significant degradation when exposed to moisture, highlighting their potential for use in wet or humid environments. FTIR analysis provided valuable information on the chemical composition of the composites. The interactions between the individual components led to the formation of new chemical bonds, strengthening the overall structure of the composite material. SEM images revealed a homogeneous distribution of the components in the composites, confirming their excellent compatibility. XRD analysis showed that the crystal structure of the composites was optimized for mechanical performance, further supporting their suitability for construction applications.

Mitigating the detrimental impacts of low- and high-density polyethylene microplastics using a novel microbial consortium on a soil-plant system: Insights and interactions

The accumulation of polyethylene microplastics (PE-MPs) in soil has raised considerable concerns; however, the effects of their persistence and mitigation on agroecosystems have not been explored. This study aimed to assess the detrimental effects of PE-MPs on a soil-plant system and evaluate their mitigation using a novel microbial consortium (MC). We incorporated low-density polyethylene (LDPE) and high-density polyethylene (HDPE) at two different concentrations, along with a control (0 %, 1 %, and 2 % w/w) into the sandy loam soil for a duration of 135 days. The samples were also treated with a novel MC and incubated for 135 days. The MC comprised three bacterial strains (Ralstonia pickettii (MW290933) strain SHAn2, Pseudomonas putida strain ShA, and Lysinibacillus xylanilyticus XDB9 (T) strain S7–10F), and a fungal strain (Aspergillus niger strain F1–16S). Sunflowers were subsequently cultivated, and physiological growth parameters were measured. The results showed that adding 2 % LDPE significantly decreased soil pH by 1.06 units compared to the control. Moreover, adding 2 % HDPE resulted in a more significant decrease in soil electrical conductivity (EC) relative to LDPE and the control. A dose-dependent increase in dissolved organic carbon (DOC) was observed, with the highest DOC found in 2 % LDPE. The addition of higher dosages of LDPE reduced soil bulk density (BD) more than HDPE. The addition of 2 % HDPE increased the water drop penetration time (WDPT) but decreased the mean weight diameter of soil aggregates (MWD) and water-stable aggregates (WSA) compared to LDPE. The results also revealed that higher levels of LDPE enhanced soil basal respiration (BR) and microbial carbon biomass (MBC). The interaction of MC and higher MP percentages considerably reduced soil pH, EC, BD, and WDPT but significantly increased soil DOC, MWD, WSA, BR, and MBC. Regarding plant growth, incorporating 2 % PE-MPs significantly reduced physiological responses of sunflower: chlorophyll content (Chl; −15.2 %), Fv/Fm ratio (-25.3 %), shoot dry weight (ShD; −31.3 %), root dry weight (RD; −40 %), leaf area (LA; −38.4 %), and stem diameter (StemD; −25 %) compared to the control; however, the addition of novel MC considerably reduced and ameliorated the harmful effects of 2 % PE-MPs on the investigated plant growth responses.

A comprehensive approach to physical recycling of hazardous waste HDPE industrial drums: Overcoming challenges in safety and foam interference

The regeneration of hazardous waste plastics are prerequisites for the sustainable development, and treatment of waste high density polyethylene (HDPE) industrial drums poses a significant challenge in the field of waste plastic recycling. In this study, a multi-step collaborative system was established for the decontamination and classification process of hazardous waste industrial drums. The yield of recycled HDPE particles exceeds 80 wt%. Through multiple experimental verifications, the optimal addition amount of antifoaming agent is 0.6 wt%, achieving the best balance between antifoaming effect and consumption. The motion process of antifoaming agent microdroplets in a static mixer was simulated. And also, through large-scale statistical analysis, the stability and reliability of physical properties and environmental safety of recycled HDPE particles were verified, supporting their reuse in various fields. In sum, this study proposes a feasible physical recycling strategy for hazardous waste HDPE industrial drums, and provides basic data from industrial practice and technical insights.

Comparative Study of Hydrobiological Parameters Between Earthen and High-Density Polyethylene (HDPE) Brackishwater Shrimp Ponds in Ratnagiri, Maharashtra

The current study was carried out to compare the hydrobiological characteristics of a selected shrimp farm in district Ratnagiri taking pond size, stocking density and culture practices into consideration. For sampling, four earthen and four high-density polyethylene (HDPE) ponds were chosen. Most of the water parameters showed significant difference with respect to different types of ponds (earthen and HDPE) viz. temperature, pH, salinity, dissolved oxygen, alkalinity and net primary productivity (NPP) of both crops (p<0.05). First crop showed significant difference among all water parameters except biochemical oxygen demand (p<0.05). Second crop (January-May) showed significant difference (p<0.05) among all parameters except hardness, ammonia, nitrite, gross primary productivity (GPP) and community respiration (CR). Phytoplankton showed significant difference (p<0.05) with respect to different types of ponds for both crops and zooplankton showed significant differences (p<0.05) only during first crop. Results indicated that high-density polyethylene (HDPE) ponds have greater consistency in water quality characteristics than earthen ponds, which could contribute to enhanced shrimp growth and survival.

Characterization of loading, relaxation, and recovery behaviors of high‐density polyethylene using a three‐branch spring‐dashpot model

AbstractThis paper presents an analysis of the stress evolution of high‐density polyethylene (HDPE) at loading, relaxation, and recovery stages in a multi‐relaxation‐recovery (RR) test. The analysis is based on a three‐branch spring‐dashpot model that uses the Eyring's law to govern the viscous behavior. The spring‐dashpot model comprises two viscous branches to represent the short‐ and long‐term time‐dependent stress responses to deformation, and a quasi‐static branch to represent the time‐independent stress response. A fast numerical analysis framework based on genetic algorithms was developed to determine values for the model parameters so that the difference between the simulation and the experimental data could be less than 0.08 MPa. Using this approach, values of the model parameters were determined as functions of deformation and time so that the model can simulate the stress response at loading, relaxation, and recovery stages of the RR test. The simulation also generated 10 sets of model parameter values to examine their consistency. The study concludes that the three‐branch model can serve as a suitable tool for analyzing the mechanical properties of HDPE, and values for the model parameters can potentially be used to characterize the difference among PEs for their mechanical performance.Highlights Developed computer programs to determine parameter values automatically. Explained the unusual stress drop during stress recovery after unloading. Evaluated the statistical range of the parameter values for the good fitting.

Nascently generated microplastics in freshwater stream are colonized by bacterial communities from stream and riparian sources.

The purpose of this study was to examine bacterial colonization of different types of microplastics through time in a freshwater ecosystem. Microplastics are persistent pollutants in aquatic ecosystems. Bacteria readily colonize microplastic surfaces and may contribute to their degradation, but the taxa involved, and their degradative abilities, differ based on factors such as microplastic chemistry, plastic age, and specific ecosystem types. Four different common types of newly manufactured microplastics, high-density polyethylene, low-density polyethylene, polypropylene, and polystyrene, were incubated for 7 weeks in a freshwater stream and sampled. Sample collection was timed to examine the development of early and late bacterial biofilm communities. Microplastics were analyzed for changes to buoyancy, weight, contact angles (an indicator of surface roughness), bacterial community composition, and the number of bacterial cells. Time was the only significant contributing factor in the development of bacterial biofilm communities on microplastic disks over the 7-week study. Notably, the Comamonadaceae were abundant early in the study and decreased in abundance with time, while the Methylococcaceae demonstrated the opposite trend. Different physicochemical properties among the various types of microplastics had only a minor effect on bacterial community compositions of biofilms growing on the microplastics. Additionally, the surfaces of all microplastic disks became rougher over time in the stream. Collectively, our results show that microplastic surfaces undergo surface modification and community succession as time progresses, regardless of microplastic type, in a freshwater stream ecosystem.

Different molecular structure of pigments versus traditional UV Stabilizers on the UV irradiation life of HDPE

As the demands on high-density polyethylene for weather resistance, aesthetics and functionality continue to improve, copper phthalocyanine has recently received attention for enhancing the weathering properties of high-density polyethylene. However, little research has been done on other pigments whether to improve weathering resistance equally. In this work, inorganic and organic pigments added to matrix were explored and compared with the industrialized UV stabilizers. It was found that pigmented polyethylene showed very little color change during 2000 h irradiation except for polyethylene/ultramarine. After 2000 h irradiation, polyethylene/copper phthalocyanine was the best among pigmented polyethylene in tensile strength, copper polychlorinated phthalocyanine following. These two pigments were similar to commonly used light stabilizers in their ability to stop the aging of polyethylene. Chrome oxide and ultramarine were worse, basically aging after irradiation of 500 h. This was consistent with the order of UV absorption ability of pigments at 310 nm - 400 nm.

Improving the thermal performance of vertical ground heat exchanger by modifying spiral tube geometry: A numerical study

Ground heat exchanger (GHE) is the most crucial element of a ground source heat pump (GSHP) system for building cooling and heating by the utilization of geothermal energy. Therefore, intending to enhance the performance of GHE, the present study conducts a computational investigation of the thermal performance of modified spiral tube vertical GHEs. Several modifications of uniform-pitched spiral GHE are made to increase its thermal performance. Some modifications are introduced as variable-pitched spiral tube GHE where spiral inlet pipes are densified in the lower part of GHEs by reducing pitch distance. Conversely, in some modifications, the position of the outlet straight pipe is changed. Water is considered as the working fluid and the inlet temperature of the water is maintained fixed at 300.15 K. After extensive analysis, it is evident that, when the outlet pipe is placed outside of the spiral coil, there is a 7.67 % enhancement in the thermal performance than a traditional uniform-pitched spiral tube GHE. However, modifications like variable-pitched spiral tube GHEs are not significant to improve the thermal performance due to the quick saturation of the ground soil temperature around the GHE pipes. To have a balance between heat transfer rate and pressure drop, thermal performance capability (TPC) and coefficient of performance improvement (COPimprvt) criterion were evaluated and it is found that the uniform-pitched spiral tube GHE along with the outlet pipe at the outside of the spiral provides maximum thermal performance with a maximum TPC value of 1.062 and provides the positive value of COPimprvt criterion. The positive values of COPimprvt indicate that the spiral tube GHEs are energy efficient based on heat transfer and pressure drop. Moreover, spiral GHE with high-density polyethylene (HDPE), concrete pile, and sandy clay outperform the other materials for pipe, backfill, and soil, respectively. Specifically, HDPE pipe, concrete backfill, and sandy clay as soil offer around 7 %, 5 %, and 7.8 % higher thermal performance compared to polyethylene, sand silica, and clay, respectively.

Neutronics simulations for the design of neutron flux monitors in SPARC.

This paper presents the development and application of high-fidelity neutronic models of the SPARC tokamak for the design of neutron flux monitors (NFM) for application during plasma operations. NFMs measure the neutron flux in the tokamak hall, which is related to fusion power via calibration. We have explored Boron-10 gamma-compensated ionization chambers (ICs) and parallel-plate Uranium-238 fission chambers (FCs). We plan for all NFMs to be located by the wall in the tokamak hall and directly exposed to neutrons streaming through a shielded opening in a midplane port. Our simulations primarily use a constructive solid geometry-based OpenMC model based on the true SPARC geometry. The OpenMC model is benchmarked against a detailed CAD-based MCNP6 model. The B10 ICs are equipped with high-density polyethylene (HDPE) sleeves, borated HDPE housings, and borated aluminum covers to shield out scattered neutrons, optimize detector response levels, and make calibration robust against changes in the tokamak hall. The B10 neutron absorption branching ratio may cause the detectors' responses to be non-linear to neutron flux >200keV. However, our simulations unveil that, in the SPARC environment and with the proposed housings and sleeves, >99% of the detector responses are induced by <100keV neutrons. U238's insensitivity to slow neutrons makes this FC a promising candidate for direct fusion neutron measurements. Along with a borated HDPE sleeve, about 60% of the FCs' responses are induced by direct neutrons.

Investigation on the mechanical properties of wood-plastic composites for the application of ceiling panels

Wood-plastic composites are relatively novel composite materials that consist of a blend of wood flour waste with high-density polyethylene and polypropylene plastic waste, designed for use in ceiling applications. Various samples were produced using different ratios from the total weight, including 20:80, 30:70, and 40:60, with sieve sizes of 0.425 mm, 1.18 mm, and 2 mm. The composites were created by melting plastics and sawdust at a temperature of 1800c utilizing the hot-press moldings technique employing diverse formulations. The properties of sample composites were analyzed experimentally based on ASTM standards to investigate water absorption levels as well as flexural strength, impact resistance hardness along with surface morphology via the design of experiments. This research study indicates that nine composite formulations consisting of HDPE and PP plastics combined with wood flour can produce favorable physio-mechanical properties. Among these various combination specimens tested in this study FS3/FC30N exhibited excellent physio-mechanical properties; including desirable values such as water absorption level at 5.5103%, flexural strength at 61.12 Mpa, impact resistance measuring 33.45 J cm−2, and hardness rating up to 80 RHB. Thus it is highly recommended for use in chipboard ceiling panel applications due to its potential benefits.

Effect of Cornshell Fibre Addition on Mechanical Properties of High-Density Polyethylene (HDPE) Composites with Aluminium Oxide (Al2O3) and Maleic Anhydride (MAH) as Coupling Agent

Effect of Cornshell Fibre Addition on Mechanical Properties of High-Density Polyethylene (HDPE) Composites with Aluminium Oxide (Al2O3) and Maleic Anhydride (MAH) as Coupling Agent

The Evaluation of the Use PET and HDPE Plastic Waste as Coarse Aggregate of Lightweight Concrete

The use of goods with plastic-based materials is familiar to society in general. Good for wrapping food, drinks, groceries, and others. Because of so much use, the problem of plastic waste cannot be avoided. Therefore, the purpose of this study is to overcome environmental land problems due to plastic waste. This research focuses on how to apply PET (Poly-Ethylene Terephthalate) and HDPE (High Density Polyethylene) plastic waste to concrete mixtures. PET plastic waste that has been chopped is then heated until melted then poured into molds and allowed to cool and harden. Then crushed and substituted as much as 5%, 10%, 15% and 20% replace the coarse aggregate to improve the characteristics of concrete. The results showed that the use of PET and HDPE in concrete resulted in decreased fill weight, lighter concrete weight, reduced compressive strength, and gave an optimum value of tensile strength at a variation of 10%. The use of PET plastic has a greater absorption value than HDPE, while the tensile strength value of PET is smaller than HDPE. Overall, it is concluded that PET and HDPE plastics have a big role in reducing the problem of plastic waste in the community