High Content Research Articles

Role of slip in hydrogen-assisted crack initiation in Ni-based alloy 725.

We conduct in situ tensile straining experiments to investigate the role of hydrogen and slip in crack initiation in nickel-based alloy 725. Our experiments reveal no tendency for hydrogen to enhance localized slip and no necessity of slip for crack initiation. We use electrochemical charging to introduce hydrogen into samples, melt extraction to measure hydrogen content, and digital image correlation to analyze localized plastic strains during in situ tensile tests in a scanning electron microscope. Cracks initiate both in regions with and without nearby localized slip. Moreover, the fraction of cracks initiating with no nearby slip is greater at higher hydrogen content. Slip-assisted crack initiation generally occurs at locations where intergranular slip is arrested, especially at intersections of slipping coherent twin boundaries with thin twin lamellae. Cracks that initiate without nearby slip occur at a wider variety of microstructural features, including inclusions, triple junctions, and surface flaws.

Out of the blue: Hyperaccumulation of molybdenum in the Indo-Pacific sponge Theonella conica.

Molybdenum is an essential micronutrient, but because of its toxicity at high concentrations, its accumulation in living organisms has not been widely demonstrated. In this study, we report that the marine sponge Theonella conica accumulates exceptionally high levels of molybdenum (46,793 micrograms per gram of dry weight) in a wide geographic distribution from the northern Red Sea to the reefs of Zanzibar, Indian Ocean. The element is found in various sponge body fractions and correlates to selenium. We further investigated the microbial composition of the sponge and compared it to its more studied congener, Theonella swinhoei. Our analysis illuminates the symbiotic bacterium Entotheonella sp. and its role in molybdenum accumulation. Through microscopic and analytical methods, we provide evidence of intracellular spheres within Entotheonella sp. that exhibit high molybdenum content, further unraveling the intricate mechanisms behind molybdenum accumulation in this sponge species and its significance in the broader context of molybdenum biogeochemical cycling.

Heterogeneous CuxO Nano-Skeletons from Waste Electronics for Enhanced Glucose Detection.

Electronic waste (e-waste) and diabetes are global challenges to modern societies. However, solving these two challenges together has been challenging until now. Herein, we propose a laser-induced transfer method to fabricate portable glucose sensors by recycling copper from e-waste. We bring up a laser-induced full-automatic fabrication method for synthesizing continuous heterogeneous CuxO (h-CuxO) nano-skeletons electrode for glucose sensing, offering rapid (< 1min), clean, air-compatible, and continuous fabrication, applicable to a wide range of Cu-containing substrates. Leveraging this approach, h-CuxO nano-skeletons, with an inner core predominantly composed of Cu2O with lower oxygen content, juxtaposed with an outer layer rich in amorphous CuxO (a-CuxO) with higher oxygen content, are derived from discarded printed circuit boards. When employed in glucose detection, the h-CuxO nano-skeletons undergo a structural evolution process, transitioning into rigid Cu2O@CuO nano-skeletons prompted by electrochemical activation. This transformation yields exceptional glucose-sensing performance (sensitivity: 9.893mAmM-1cm-2; detection limit: 0.34μM), outperforming most previously reported glucose sensors. Density functional theoryanalysis elucidates that the heterogeneous structure facilitates gluconolactone desorption. This glucose detection device has also been downsized to optimize its scalability and portability for convenient integration into people's everyday lives.

Statistical Copolymerization-Induced Self-Assembly.

Statistical copolymers have been extensively used in chemical industries and our daily lives, owing to their ease of synthesis and functionalization. However, self-assembly based on statistical copolymers has been haunted by high interfacial energy, poor stability, and low concentration. We proposed the statistical copolymerization-induced self-assembly (stat-PISA) as a general strategy for one-step preparing stable statistical copolymer assemblies with high solids content. The concept was demonstrated through a model dispersion polymerization system comprising a charged hydrophilic monomer and a core-forming monomer, producing spherical micelles via a spinodal decomposition mechanism with an interconnected network intermediate. The stat-PISA was tunable by varying the fraction of charged monomer, the polymer chain length, and the solids content. The statistical copolymer micelles were demonstrated to be a potential Pickering emulsifier with superior stabilizing performances compared to their block copolymer counterparts. The general applicability of stat-PISA was demonstrated by preparing statistical copolymer assemblies with varying surface charges and chemical compositions. Particularly, this strategy is feasible for conventional free radical polymerization, promising for industrial scale-up.

Investigation of hydrogen uptake capacity for FAU, MOR, MTW, MWW

In this study, the hydrogen storage properties of various synthetic zeolites, including Zeolite Y (FAU), Mordenite (MOR), ZSM-12 (MTW), and MCM-22 (MWW) are determined at 77 K and atmospheric pressure. The structures of the zeolites are characterized by XRD, ICP-OES, FE-SEM, TGA and N2 adsorption-desorption isotherms. The results show that H-MCM-22 zeolite has the highest hydrogen storage capacity at 1.0 bar with 1.19 wt%, followed by H-MOR zeolite with 1.05 wt%, H–Y zeolite with 0.75 wt% and H-ZSM-12 zeolite with 0.60 wt%. The hydrogen adsorption data on FAU, MOR, MTW, and MWW at 77 K obey the Sips isotherm model. The experimental data show that the ultra-micropore volume of the zeolite is effective in hydrogen adsorption at low-pressure ranges. In addition, increasing the aluminum content of the zeolite increases the hydrogen adsorption capacity of the zeolite at atmospheric pressure. Therefore, zeolites with channel sizes close to the kinetic diameter of a hydrogen molecule, large cage volumes, and high aluminum content are potential candidates for energy storage applications.

Enhancing high-efficient cadmium biosorption of Escherichia coli via cell surface displaying metallothionien CUP1

ABSTRACT Cadmium (Cd) is one of the common heavy metal pollutants in soil, which can induce various diseases and pose a serious threat to human health. Metallothioneins (MTs) are well-known for their excellent metal binding ability due to a high content of cysteine, which has great potential for heavy metal chelation. In this study, we used the Escherichia coli (E. coli) surface display system LPP-OmpA to construct a recombinant plasmid pBSD-LCF encoding LPP-OmpA-CUP1-Flag fusion protein. Then we displayed the metallothionein CUP1 from Saccharomyces cerevisiae on E. coli DH5α surface for Cd removing. The feasibility of surface display of metallothionein CUP1 in recombinant E. coli DH5α (pBSD-LCF) by Lpp-OmpA system was proved by flow cytometry and western blot analysis, and the specificity of the fusion protein in the recombinant strain was also verified. The results showed that the Cd2+ resistance capacity of DH5α (pBSD-LCF) was highly enhanced by about 200%. Fourier-transform infrared spectroscopy showed that sulfhydryl and sulfonyl groups were involved in Cd2+ binding to cell surface of DH5α (pBSD-LCF). Meanwhile, Cd removal rate by DH5α (pBSD-LCF) was promoted to 95.2%. Thus, the recombinant strain E. coli DH5α (pBSD-LCF) can effectively chelate environmental metals, and the cell surface expression of metallothionein on E. coli can provide new ideas and directions for heavy metals remediation.

Experimental and numerical study on the influence of N2/H2 on the laminar combustion characteristics of syngas premixed flames

This paper primarily analyzes the influence of N2 and H2 content on the laminar combustion characteristics of low calorific value syngas, using a constant-volume combustion bomb to measure the laminar combustion velocity (SL) of the fuel and compare it with five commonly used mechanisms. The study reveals that higher N2 content significantly reduces the SL of CO/CH4/CO2 mixed fuels, primarily due to a general decrease in the mole fractions of key intermediates and net reaction rates. Increasing H2 content leads to an increase in the SL of CO/CH4/CO2/N2 mixed fuels. The thermal effect becomes increasingly prominent with the elevation of H2 content, while the proportion of thermal effect initially decreases and subsequently increases as the equivalence ratio rises. With the increase in N2 content, the mole fraction of NO experiences a significant decrease, and the rate of decline in thermal NO production is even faster. Conversely, with the increase in H2 content, the rate of rise in non-thermal NO generation is faster, and the mole fraction of NO tends to increase.

Multiscale modeling and thermal conductivity evaluation of nano-reinforced composite materials with pore defect

The performance of resin-based composite materials often exhibits diversity due to the designability of various components. Thermal conductivity, an important thermal parameter of the composite, plays a significant role in thermal-chemical reactions, thermal stress analysis, temperature conduction, etc. However, it is relatively difficult to experimentally explore the thermal conduction mechanism of hybrid composite materials, mainly due to the relatively difficult control of various components. Therefore, this paper proposes a sequentially coupled cross-scale numerical method to characterize the thermal conductivity of nano-reinforced composite materials with pores by a multiscale periodic Representative Volume Element model generated by an improved Random Sequential Absorption algorithm. Firstly, periodic temperature boundary conditions are described, and the thermal conductivity performances of nano-reinforced matrix and composite with pores are investigated based on the finite element homogenization theory. Then, the proposed modes are validated and grid sensitivity analysis is conducted, indicating that the optimal grid sizes for the RVE models are 1.9 nm for the nano-reinforced matrix and 0.14 μm for the composite with pores based on a comprehensive comparison of four pore characterization methods, respectively. Furthermore, the study explored the effect of multiple parameters including nanoparticle content, pore content, and pore shape on thermal conductivity. Numerical findings reveal that the thermal conductivity of the nanocomposite matrix exhibits a linear increase with higher particle content. Specifically, compared to 0 % particle content, the thermal conductivity rises by 141.92 % at 12 % particle content. While the composite material's transverse thermal conductivity is sensitive to porosity content, it is less influenced by pore shape. The method proposed in this paper provides an effective approach for studying the thermal conduction of nano-reinforced composite materials with pores, and the research findings also offer theoretical guidance for process engineers.

Improved slag resistance of ferrotitanium slag based Al2O3-SiC-C castables: The effect of reaction between SiC and TiO2

Ferrotitanium slag is a kind of waste slag produced by smelting ferrotitanium alloy. It has high refractoriness (>1790 ℃) and Al2O3 content (≥70 wt%), which can be used to replace bauxite to prepare Al2O3-SiC-C castables. However, excessive substitution will lead to the decrease of slag resistance of Al2O3-SiC-C castables because of impurities in the ferrotitanium slag. In this paper, the slag resistance of ferrotitanium slag based Al2O3-SiC-C castables was improved by increasing the SiC content. The results showed that the castables with 13 wt% SiC had good mechanical properties. Increasing the amount of SiC was beneficial to improve the slag resistance. SiC content increased from 5 wt% to 22 wt%, the erosion index of dynamic slag resistance decreased from 17.05 % to 11.18 %. During the dynamic slag resistance, the TiO2 in the ferrotitanium slag dissolved in the slag, then the SiC reacted with TiO2 in the slag to form TiC coating on the surface of SiC particles. SiC particles wrapped by TiC widely existed in the reaction layer, which prevented further erosion of the slag. Further, the reaction of SiC with TiO2 to consume TiO2 and generate SiO2 increased the viscosity of the slag in the reaction layer, thus hindering slag penetration.

The first complete mitochondrial genome of the genus Laelaps with novel gene arrangement reveals extensive rearrangement and phylogenetics in the superfamily Dermanyssoidea.

We collected 56 specimens ofLaelaps chini from the endemic Hengduan Mountain rat species (Eothenomys miletus) and obtained the first complete mitochondrial genome of L. chini by next-generation sequencing (NGS). The L. chini mitogenome is 16,507bp in size and contains 37 genes and a control region of 2380bp in length. The L. chini mitogenome has a high AT content and a compact arrangement with four overlapping regions ranging from 1 to 2bp and 16 spacer regions ranging from 1 to 48bp. We analyzed 13 protein-coding genes of L. chini mitogenome andfound that protein-coding genes in the L. chini mitogenome preferred codons ending in A/U and codon usage pattern was mainly influenced by natural selection. Cox1 has the slowest evolution rate and cox3 has the fastest evolution rate. We combined the mitochondrial genome of eight species ofgamasid mites in the superfamily Dermanyssoidea from Genbank and theL. chini mitochondrial genometo analyze its rearrangement patterns and breakpoint numbers. We found that the L. chini mitogenome showed a novel arrangement pattern and nine species ofgamasid mites in the superfamily Dermanyssoidea, which have been sequenced complete mitochondrial genomes to date, all showed different degrees of rearrangement. Laelaps chini, Echinolaelaps echidninus and Echinolaelaps fukinenensis were closely related species based on genetic distance and phylogenetic analyses. Notably they are clustered with Varroa destructor of the family Varroidae, suggesting that the family Varroidae is more closely related to the family Laelapidae, but more data are needed to test whether Varroa can be classified under the family Laelapidae. The L. chini mitogenome is the first complete mitochondrial genome for the genus Laelaps, and contributes to further exploration of the mitochondrial gene rearrangements and phylogeny for the superfamily Dermanyssoidea.

Nitrogen deficiency tolerance conferred by introgression of a QTL derived from wild emmer into bread wheat

Key messageGenetic dissection of a QTL from wild emmer wheat, QGpc.huj.uh-5B.2, introgressed into bread wheat, identified candidate genes associated with tolerance to nitrogen deficiency, and potentially useful for improving nitrogen-use efficiency.Nitrogen (N) is an important macronutrient critical to wheat growth and development; its deficiency is one of the main factors causing reductions in grain yield and quality. N availability is significantly affected by drought or flooding, that are dependent on additional factors including soil type or duration and severity of stress. In a previous study, we identified a high grain protein content QTL (QGpc.huj.uh-5B.2) derived from the 5B chromosome of wild emmer wheat, that showed a higher proportion of explained variation under water-stress conditions. We hypothesized that this QTL is associated with tolerance to N deficiency as a possible mechanism underlying the higher effect under stress. To validate this hypothesis, we introgressed the QTL into the elite bread wheat var. Ruta, and showed that under N-deficient field conditions the introgression IL99 had a 33% increase in GPC (p < 0.05) compared to the recipient parent. Furthermore, evaluation of IL99 response to severe N deficiency (10% N) for 14 days, applied using a semi-hydroponic system under controlled conditions, confirmed its tolerance to N deficiency. Fine-mapping of the QTL resulted in 26 homozygous near-isogenic lines (BC4F5) segregating to N-deficiency tolerance. The QTL was delimited from − 28.28 to − 1.29 Mb and included 13 candidate genes, most associated with N-stress response, N transport, and abiotic stress responses. These genes may improve N-use efficiency under severely N-deficient environments. Our study demonstrates the importance of WEW as a source of novel candidate genes for sustainable improvement in tolerance to N deficiency in wheat.

Chemical composition of Ecstasy tablets seized in Poland between 2005 and 2020.

The most commonly associated substance found in Ecstasy tablets is MDMA (3,4-methylenedioxymethamphetamine). In our study, we showed how the composition of psychoactive ingredients in Ecstasy tablets seized on the drug market in Poland has changed in the years 2005-2020. The study material consisted of nearly 20,000 single Ecstasy tablets seized by representatives of law enforcement (the police, prosecutors) from 2005 to 2020 and analysed by the Institute of Forensic Research, Krakow, Poland. The analysis of the tablets was carried out by gas chromatography-mass spectrometry (GC-MS), high-performance liquid chromatography with diode array detection (HPLC-DAD) and ultra-high-performance liquid chromatography with photodiode array detection (UHPLC-PDA). Currently, new types of MDMA tablets are introduced onto the market, available in various colours and shapes. Our study showed that tablets sold on the street as Ecstasy have variable purity and sometimes contain little or no MDMA. The mean content of MDMA in one tablet seized in 2005-2011 decreased from 90 to 50mg. In 2013, Ecstasy tablets with a very high MDMA content (average 195mg per tablet) appeared on the market, but in the next 2years, the MDMA content decreased again. From 2016, the average MDMA content began to rise again, ranging from 60 to 280mg. Tablets sold as Ecstasy also contained completely different psychoactive substances, including new psychoactive substances (NPS) (found in almost 20% of all examined tablets sold as Ecstasy) belonging to different chemical groups or their dangerous combinations (i.e. phenylethylamines, piperazines, tryptamines, cathinones, arylalkylamines, arylcyclohexylamines and piperidines). Such a large variety of psychoactive substances in Ecstasy tablets is associated with a high risk for users unaware of their composition.

Measurement of radon exhalation rate and radiation doses in fly ash samples.

Coal based thermal power plants contribute about ~ 72% of the power generation in India. Indian coal is of bituminous type, having a high ash content with 55-60% ash. Due to considerable environmental importance the collected fly ash has become a subject of worldwide interest in recent years. In the present study radon exhalation rate and the activity concentration of 226Ra, 232Th and 40K radionuclides in fly ash samples from Kasimpur Thermal Power Plant, Aligarh, Uttar Pradesh, India have been measured by 'Sealed Can technique' using LR-115 type II detectors and a low-level NaI (Tl)- based gamma-ray spectrometer, respectively. Radon exhalation rate has been found to vary from 57.1±5.3 to 119.4±7.7 mBq m-2h-1 with an average value of 87.3±5.8 mBq m-2h-1. Activity concentration of 226Ra ranged from 20.0±8.5 to 30.0±9.7Bqkg-1 with an average value 23.4±9.0Bqkg-1, 232Th ranged from 17.0±9.9 to 69.0±13.8Bqkg-1 with an average value of 46.5±12.1Bqkg-1 and 40K ranged from 130.0±7.2 to 332.0±11.1Bqkg-1 with an average value of 177.0±8.1Bqkg-1.

Interactions between Iron Minerals and Dissolved Organic Matter Derived from Microplastics Inhibited the Ferrihydrite Transformation as Revealed at the Molecular Scale.

Microplastic-derived dissolved organic matter (MP-DOM) is an emerging carbon source in the environment. Interactions between MP-DOM and iron minerals alter the transformation of ferrihydrite (Fh) as well as the distribution and fate of MP-DOM. However, these interactions and their effects on both two components are not fully elucidated. In this study, we selected three types of MP-DOM as model substances and utilized Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) and extended X-ray absorption fine structure (EXAFS) spectroscopy to characterize the structural features of DOMs and DOM-mineral complexes at the molecular and atomic levels. Our results suggest that carboxyl and hydroxyl groups in MP-DOM increased the Fe-O bond length by 0.02-0.03 Å through interacting with Fe atoms in the first shell, thereby inhibiting the transformation of Fh to hematite (Hm). The most significant inhibition of Fh transformation was found in PS-DOM, followed by PBAT-DOM and PE-DOM. MP-DOM components, such as phenolic compounds and condensed polycyclic aromatics (MW > 360 Da) with high oxygen content and high unsaturation, exhibited stronger mineral adsorption affinity. These findings provide a profound theoretical basis for accurately predicting the behavior and fate of iron minerals as well as MP-DOM in complex natural environments.

Physiological, transcriptomic and metabolomic insights of three extremophyte woody species living in the multi-stress environment of the Atacama Desert.

In contrast to Neltuma species, S. tamarugo exhibited higher stress tolerance, maintaining photosynthetic performance through enhanced gene expression and metabolites. Differentially accumulated metabolites include chlorophyll and carotenoids and accumulation of non-nitrogen osmoprotectants. Plant species have developed different adaptive strategies to live under extreme environmental conditions. Hypothetically, extremophyte species present a unique configuration of physiological functions that prioritize stress-tolerance mechanisms while carefully managing resource allocation for photosynthesis. This could be particularly challenging under a multi-stress environment, where the synthesis of multiple and sequential molecular mechanisms is induced. We explored this hypothesis in three phylogenetically related woody species co-occurring in the Atacama Desert, Strombocarpa tamarugo, Neltuma alba, and Neltuma chilensis, by analyzing their leaf dehydration and freezing tolerance and by characterizing their photosynthetic performance under natural growth conditions. Besides, the transcriptomic profiling, biochemical analyses of leaf pigments, and metabolite analysis by untargeted metabolomics were conducted to study gene expression and metabolomic landscape within this challenging multi-stress environment. S. tamarugo showed a higher photosynthetic capacity and leaf stress tolerance than the other species. In this species, a multifactorial response was observed, which involves high photochemical activity associated with a higher content of chlorophylls and β-carotene. The oxidative damage of the photosynthetic apparatus is probably attenuated by the synthesis of complex antioxidant molecules in the three species, but S. tamarugo showed the highest antioxidant capacity. Comparative transcriptomic and metabolomic analyses among the species showed the differential expression of genes involved in the biosynthetic pathways of key stress-related metabolites. Moreover, the synthesis of non-nitrogen osmoprotectant molecules, such as ciceritol and mannitol in S. tamarugo, would allow the nitrogen allocation to support its high photosynthetic capacity without compromising leaf dehydration tolerance and freezing stress avoidance.

Effect of soil additives on biogeochemistry of ultramafic soils—an experimental approach with Brassica napus L

Ultramafic soils are characterized by low productivity due to the deficiency of macroelements and high content of Ni, Cr, and Co. Incorporation of ultramafic soils for agricultural and food production involves the use of fertilizers. Therefore, this study aims to find the soil additive that decreases the metallic elements uptake by plant using Brassica napus as an example. In this study, we evaluate the effect of manure (0.5 g N/kg of soil), humic acids (1 g of Rosahumus/1 dm3 H2O; 44% C), KNO3 (0.13 g K/kg of soil), lime (12.5 g/kg of soil), (NH4)2SO4 (0.15 g N/kg of soil), and Ca(H2PO4)2) (0.07 g P/kg of soil) on the phytoavailability of metallic elements. The effect of soil additives on metallic elements uptake by Brassica napus was studied in a pot experiment executed in triplicates. Statistical analysis was applied to compare the effects of additives in ultramafic soil on plant chemical composition relative to control unfertilized ultramafic soil (one-way ANOVA and Kruskal–Wallis test). The study shows that in almost all treatments, metallic elements content (Ni, Cr, Co, Al, Fe, Mn) is higher in roots compared to the aboveground parts of Brassica napus except for (NH4)2SO4, in which the mechanism of Mn accumulation is opposite. The main differences between the treatments are observed for the buffer properties of soil and the accumulation of specific metals by studied plants. The soils with the addition of lime and manure have the highest buffer properties in acidic conditions (4.9-fold and 2.1-fold increase relative to control soil, respectively), whereas the soil with (NH4)2SO4 has the lowest effect (0.8-fold decrease relative to control soil). Also, the addition of manure increases the biomass of aboveground parts of B. napus (3.4-fold increase) and decreases the accumulation of Ni (0.6-fold decrease) compared to plants cultivated in the control soil. On the contrary, the addition of (NH4)2SO4 noticeably increases the accumulation of Ni, Co, Mn, and Al in aboveground parts of B. napus (3.2-fold, 18.2-fold, 11.2-fold, and 1.6-fold, respectively) compared to plant grown in control soil, whereas the humic acids increase the accumulation of Cr in roots (1.6-fold increase). Therefore, this study shows that manure is a promising fertilizer in agricultural practices in ultramafic soil, whereas (NH4)2SO4 and humic acids must not be used in ultramafic areas.

SORGHUM AND ECO-FRIENDLY AGRICULTURE IN INDONESIA

Purpose: This paper reviews the research results on sorghum plants that use organic fertilizer to increase production. Theoretical reference: Sorghum plants also need to be fertilized to increase productivity. The use of chemical fertilizers in plants will have a broad impact on the environment and human health, so it is necessary to have an alternative organic fertilizer that is safe and leads to environmentally friendly agriculture, in addition to being a source of nutrients and to improve the properties of infertile soil. Methods: This research is supported and studied with a descriptive qualitative method. All information is collected through document analysis. The literature taken is the most recent year (the last 10 years). The productivity resulting from applying organic fertilizers is compared to the productivity without applying organic fertilizers. Then see the increase in results. In addition to productivity, the results of research on the quality of sorghum seeds are also seen. Results: According to various research results, applying organic fertilizers increases productivity ranging from 5.66% to 71.28% with an average of 20.96% compared to without organic fertilizers. Conclusions: Indonesia is one of the countries with the potential for the development of sorghum which can be done by environmentally friendly cultivation and the use of organic fertilizers because it is proven to increase productivity and improve the quality of sorghum seeds. Sorghum (Sorghum bicolor (L.) Moench) planting can sustainably meet more food needs because sorghum plants have a higher protein content than corn and rice plants.

Investigation of the Impacts of Solder Alloy Composition and Temperature Profile on Fatigue Life of Ball Grid Array Solder Joints Under Accelerated Thermal Cycling

Abstract This study investigated the thermal fatigue reliability of ball grid array (BGA) solder joints under accelerated thermal cycling, considering the impacts of solder alloy and temperature profile. Applying the Darveaux solder joint reliability assessment, simulations consider lead-based (63Sn37Pb and 62Sn36Pb2Ag) and lead-free (SAC105, SAC305, and SAC405) solder alloys under temperature profiles: 0°C (Tmin) to 100°C (Tmax), −40°C to 85 °C, −40 °C to 125 °C, and −40 °C to 150 °C. Results indicate that SAC305 exhibited the highest equivalent stress, while 63Sn37Pb demonstrated the highest plastic strain and creep strain energy density. SAC105 displayed the lowest stress and strain parameters. Moreover, increasing the thermal cycling temperature range intensifies stress, strain, and damage parameters, with −40 °C to 150 °C showing the highest magnitudes. SAC405 exhibited superior thermal fatigue life compared to other alloys, with its cycles to failure outperforming 63Sn37Pb, SAC105, 63Sn36Pb2Ag, and SAC305 by 16832, 11992, 6218, and 3601 cycles, respectively. Lower temperature ranges enhance thermal fatigue life, with 0 °C to 100 °C recording 8%, 33%, and 53% higher life than −40 °C to 85 °C, −40 °C to 125 °C, and −40 °C to 150 °C, respectively. Notably, higher silver content and lower temperature ranges were associated with increased thermal fatigue life, providing valuable insights for BGA solder joint reliability enhancement.

Rational design of membrane electrode assembly for anion exchange membrane water electrolysis systems

Anion exchange membrane water electrolysis (AEMWE) is a promising and potentially low-cost technology for producing green hydrogen, but a novel manufacturing technique with rational design of the electrodes is essential to improve the performance and stability. In this work, we investigate the effect of electrode structure on activity and the stability of AEMWEs by fabricating membrane electrode assemblies (MEAs). For the first time, the decal transfer method with platinum-group-metal-free (PGM-free) catalyst was successfully used in AEMWEs. With this method, deposition of a compact catalyst layer (CL) on the membrane was achieved without damaging neither the CL nor the membrane. The MEAs were designed for AEMWE using 1 M KOH as the electrolyte and the ionomer content was optimized for both cathode and anode. In the anode, a low ionomer loading improved activity and ionic conductivity, however, a higher ionomer content was beneficial for the cathode. Furthermore, the type of ionomer on the anode side has shown to be the major reason of loss of performance over time. An ionomer with low (1.4–1.7 meq g−1) Ion Exchange Capacity (IEC) and Nafion™ ionomer greatly improved the stability.

Surface properties of the seas of Titan as revealed by Cassini mission bistatic radar experiments

Saturn’s moon Titan was explored by the Cassini spacecraft from 2004 to 2017. While Cassini revealed a lot about this Earth-like world, its radar observations could only provide limited information about Titan’s liquid hydrocarbons seas Kraken, Ligeia and Punga Mare. Here, we show the results of the analysis of the Cassini mission bistatic radar experiments data of Titan’s polar seas. The dual-polarized nature of bistatic radar observations allow independent estimates of effective relative dielectric constant and small-scale roughness of sea surface, which were not possible via monostatic radar data. We find statistically significant variations in effective dielectric constant (i.e., liquid composition), consistent with a latitudinal dependence in the methane-ethane mixing-ratio. The results on estuaries suggest lower values than the open seas, compatible with methane-rich rivers entering seas with higher ethane content. We estimate small-scale roughness of a few millimeters from the almost purely coherent scattering from the sea surface, hinting at the presence of capillary waves. This roughness is concentrated near estuaries and inter-basin straits, perhaps indicating active tidal currents.