Trigonal Research Articles

Synthesis and characterisation of high-purity alumina achieved through a dip coating process

ABSTRACT This study focuses on the synthesis of alumina using a modified citrate method. The chelation process involved thermal activation through biphasic drops, employing the hydrated aluminium nitrate precursor and citric acid complex. The thermal behaviour of the resulting gel was investigated using DSC/TGA followed by FTIR, which revealed absorption bands at distinct temperatures leading up to the formation of white crystallised alumina powder at 1000°C. Structural analysis via XRD parameters indicated that the obtained sample is refined in the hexagonal system with the R-3C space group. SEM observations demonstrated morphology akin to an overlapping hive, highlighting significant stoichiometric purity. The semi-colloidal sol was applied in a dip-coating method to reinforce the matrix of a steel substrate, specifically E335. SEM-EDS analyses revealed the adhesion recorded as a brittle intermetallic phase. Additionally, a transformation of 22% haematite to magnetite was observed under the conditions of coating.

The Influence of Sn Addition on the Magnetocaloric Effects, Magnetic and Mechanical Properties of Fe<sub>2</sub>P-Type Mn-Fe-P-Si Compounds

Mn1.25Fe0.65-xSnxP0.50Si0.50 (0, 0.02, 0.04, 0.05, 0.06, 0.08, 0.09, 0.10, 0.20) series compounds were prepared by mechanical alloying and solid-phase sintering, and their mechanical and magnetic properties were studied. The XRD measurement results show that all the compounds crystalize in Fe2P hexagonal structures, with a space group of P-62m. With the increase in Sn content, the compressive strength is significantly improved, the Curie temperature of the compound gradually decreases, and the nature of magnetic transition is tuned from a weak to strong first-order one, which is confirmed by the increase of thermal hysteresis of the compounds. The maximum magnetic entropy change of the compound increases from 9.3 J/kg·K at x = 0 to 17.2 J/kg·K at x = 0.04 under a magnetic field change of 0 - 3 T.

Atomic Layer Deposition of Nickel Using Ni(dmamb)2 and ZnO Adhesion Layer Without Plasma

In this study, a novel deposition technique that utilizes diethylzinc (C4H10ZnO) with H2O to form a ZnO adhesion layer was proposed. This technique was followed by the deposition of vaporized nickel(II) 1-dimethylamino-2-methyl-2-butoxide (Ni(dmamb)2) and H2 gas to facilitate the deposit of uniform layers of nickel on the ZnO adhesion layer using atomic layer deposition. Deposition temperatures ranged from 220 to 300 °C. Thickness, composition, and crystallographic structure results were analyzed using spectroscopic ellipsometry, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD), respectively. An average growth rate of approximately 0.0105 angstroms per cycle at 260 °C was observed via ellipsometry. Uniform deposition of ZnO with less than 1% of Ni was displayed by utilizing the elemental analysis function via SEM, thereby providing high-quality images. XPS revealed ionizations consistent with nickel and ZnO through the kinetic and binding energies of each detected electron. XRD provided supplemental information regarding the validity of ZnO by exhibiting crystalline attributes, revealing the presence of its hexagonal wurtzite structure.

Stability and properties of six new Ru3Al structures: A first-principles study of mechanical, electronic, and superconducting properties

Ruthenium–aluminium (Ru–Al) alloys demonstrate excellent properties; however, the Ru3Al structure has a higher formation energy than those of other Ru–Al structures. Herein, to identify more stable Ru3Al structures, we employed the CALYPSO code and discovered six stable structures: one hexagonal structure, two monoclinic structures and three orthorhombic structures. First-principles calculations and the density functional theory were used to assess their mechanical, electrical and superconducting properties. The formation energies of these newly discovered Ru3Al structures were lower than those of previously proposed structures, confirming their thermodynamic stability. Elastic constant calculations indicated that all the structures were mechanically stable and ductile. Moreover, electronic structure analyses revealed that the structures were metallic, primarily owing to the contribution of Ru d orbitals. Phonon dispersion and density of states analyses also confirmed the dynamic stability of the structures, with low-frequency phonons contributing considerably to electron–phonon coupling. The superconducting transition temperatures (Tc) of the structures were calculated using the Allen–Dynes-modified McMillan equation. The Cmcm structure showed the highest Tc of 3.99 K, and the P2/c structure showed the lowest Tc of 1.56 K. Overall, this study identified six novel and stable Ru3Al structures with good mechanical and superconducting properties, potentially advancing the development of Ru–Al-based superconductors.

Exploration of laser-assisted chemical bath for enhancing synthesis of undoped and nickel-doped zinc oxide and its potential applications in water purification and mitigating antimicrobial resistance

This study aims to explore the antimicrobial and photocatalytic efficiencies of pure and Ni-doped ZnO nanostructures produced via Laser-assisted Chemical Bath Synthesis (LACBS) to develop sustainable solutions for water treatment and pathogen control amid the global water crisis exacerbated by climate change and environmental pollution. Utilizing zinc acetate dihydrate and hexamethylenetetramine, the nanostructures were synthesized with Ni doping levels of 0.0 %, 1.5 %, 3.0 %, and 4.5 %, targeting their promising photocatalytic and antimicrobial properties to combat contaminants from pharmaceuticals, agriculture, and industries. Morphological analyses using Scanning Electron Microscopy showed a transition from hexagonal particles to nanoflowers, enhancing photocatalytic activity due to increased surface-to-volume ratio. X-ray Diffraction confirmed the hexagonal wurtzite structure, with variations in peak intensities indicating improved crystallinity with Ni doping. Energy Dispersive X-ray analysis verified the purity and successful incorporation of Ni. Photocatalytic assessments indicated up to 99.24 % degradation of Methylene Orange dye under blue laser irradiation within 60 minutes, correlating with Ni content. Antimicrobial tests demonstrated effective inhibition of pathogens such as Escherichia coli, Staphylococcus aureus, and additional strains like Candida albicans and Klebsiella pneumonia, with increasing zones of inhibition corresponding to higher Ni levels, extending up to 37 mm. The results underscore the dual functionality of ZnO nanostructures for applications in sustainable water treatment and antimicrobial controls, highlighting the need for future studies to examine the impacts of further increased doping concentrations on the material properties and efficacy.

Synthesis and application of SBA-15 adsorbent for the removal of organic and inorganic substances.

This study investigates the adsorption of pollutants with different chemical structures; organic Naphtol Green B (NGB) dye and copper on a nanocomposite material with a hexagonal structure of the SBA-15 type. This research is divided into two main parts: the first carries out the synthesis of SBA-15 (Santa Barbra Amourphous) and its derivatives phases functionalized by 3-aminopropyl-triethoxylane (APTES) and calcined at 823K. The second part presents the influence of the adsorption conditions on the adsorption efficiency of NGB dye and copper. High-resolution X-ray diffractogram (XRD) showed three distinct peaks characteristic of highly ordered mesoporous material. Nitrogen adsorption-desorption isotherm of SBA-15 at 77K° is type IV typical of mesoporous materials. In addition, Fourier transform infrared spectroscopy (FT-IR) was also used in the characterization before and after the adsorption of the selected pollutants. At optimal conditions of pH 5.2, initial concentration of 50mg/L, adsorbent dosage of 20mg, and at adsorption time of 90min the maximum removal of pollutants reached 76% and the adsorption capacity was 227.25mg/g for NGB dye and 221.006mg/g for copper. Furthermore, the adsorption kinetics followed the pseudo-second-order model, indicating that chemisorption was the dominant mechanism and the Sips isotherm model best described the adsorption data. Our research demonstrates that the SBA-15 material after modification is an effective adsorbent for removing effluents regardless of their different chemical structure (organic and inorganic).

Strain-Controlled Electronic and Magnetic Properties of Janus Nitride MXene Monolayer MnCrNO2

Two-dimensional (2D) van der Waals (vdW) magnetic materials show potential for the advancement of high-density, energy-efficient electronic and spintronic applications in future memory and computation. Here, by using first-principles density functional theory (DFT) calculations, we predict a new 2D Janus nitride MXene MnCrNO2 monolayer. Our results suggest that the optimized MnCrNO2 monolayer possesses a hexagonal structure and exhibits good dynamical stability. The intrinsic monolayer MnCrNO2 exhibits semiconductive properties and adopts a ferromagnetic ground state with an out-of-plane easy axis. It can sustain strain effects within a wide range of strains from −10% to +8%, as indicated by the phonon dispersion spectra. Under the biaxial tensile strain, a remarkable decrease in the bandgap of the MnCrNO2 is induced, which is attributed to the distinct roles played by Mn and Cr in the VBM or CBM bands. Furthermore, when the compressive strain reaches approximately −8%, the magnetic anisotropy undergoes a transition from an out-of-plane easy axis to an in-plane easy axis. This change is mainly influenced by the efficient hybridization of the d orbitals, particularly in Mn atoms. Our study of the Janus MXene MnCrNO2 monolayer indicates its potential as a promising candidate for innovative electronic and spintronic devices; this potential is expected to create interest in its synthesis.

Ultrasensitive Detection of Dimethylamine Gas for Early Diagnosis of Parkinson's Disease Using CeO2-Coated Ti3C2Tx MXene/Carbon Nanofibers.

Parkinson's disease is a prevalent neurological disorder, with dimethylamine (DMA) recognized as a crucial breath biomarker, particularly at the parts per billion (ppb) level. Detecting DMA gas at this level, especially at room temperature and high humidity, remains a formidable challenge. This study presents an ultrasensitive chemiresistor DMA gas sensor, leveraging the CeO2-coated Ti3C2Tx MXene/carbon nanofiber (CeO2/MXene/C NFs) heterostructure to enhance dimethylamine sensing. The high conductivity of MXene, combined with C-Ti-O bonds and a sp2 hybridized hexagonal carbon structure, increases surface active sites. The presence of Ce3+ promotes the formation of surface-active oxygen species, while the MXene-CeO2 heterojunction broadens the electron depletion layer. Theoretical calculations reveal that the highest adsorption energy for DMA gas is at the Ce top site, explaining the sensor's satisfactory sensitivity, rapid response and recovery process, low detection limit (5 ppb), and high selectivity at room temperature. The Ce3+/Ce4+ dynamic self-refresh mechanism, involving surface hydroxyl elimination, enhances the sensor's performance under high-humid conditions. Clinical breath tests demonstrate the sensor's ability to distinguish between healthy individuals and Parkinson's disease patients, paving the way for developing next-generation sensors for early diagnosis of neurological disorders.

Insight into the Structural and Magnetic Properties of PrZnSi and NdZnSi Compounds Featuring Large Low-Temperature Magnetocaloric Effects.

The magnetocaloric (MC) and magnetic phase transition (MPT) properties in various types of rare earth (RE)-based magnetic materials have been intensively investigated recently, which are aimed at developing suitable MC materials for low-temperature cooling applications and better elucidating their inherent physical properties. We herein provide a combined experimental and theoretical investigation into two new light RE-based magnetic materials, namely, PrZnSi and NdZnSi compounds, regarding their structural, magnetic, MPT, and low-temperature MC properties. Both of these compounds crystallize in an AlB2-type hexagonal structure with a symmetry of the crystallographic space group P6/mmm and reveal a typical second-order-type MPT with ordering temperatures (TC) at approximately 13.5 and 18.5 K for PrZnSi and NdZnSi compounds, respectively. Moreover, they all exhibit large reversible low-temperature MC effects and remarkable performances, which are identified by the parameters of maximum magnetic entropy changes, relative cooling power, and temperature-averaged entropy change (temperature lift 5 K). The deduced values of these MC parameters under a magnetic field change of 0-7 T reach 16.3 J/kgK, 294.46 J/kg, and 15.79 J/kgK for PrZnSi and 15.4 J/kgK, 284.84 J/kg, and 14.95 J/kgK for NdZnSi, respectively, which are evidently better than those of most updated light RE-based magnetic materials with remarkable low-temperature MC performances, indicating that PrZnSi and NdZnSi compounds hold potentials for practical cooling applications.

Cryogenic temperatures promote the pressure-induced polymorphic transition in CoCrFeMnNi high entropy alloy

Pressure-induced polymorphism has recently been demonstrated in several high entropy alloys. This offers a new window into the much-debated issue of phase selection and stability in these systems. Here, we examine the effect of cryogenic temperatures on the pressure-induced transition from face centered cubic to hexagonal close-packed structures of the prototype CoCrFeMnNi (Cantor) alloy. We observe a reduction in the critical pressure for the onset of the polymorphic transition as the temperature decreases, confirming the progressive stabilization of the hexagonal phase with decreasing temperature previously predicted by ab initio calculations accounting for magnetic interactions. We argue that in situ high-pressure experiments at cryogenic temperatures, which suppress time-dependent transformation triggered at higher temperatures, present a unique opportunity to significantly improve our understanding of these complex alloys.

Using the Plasma Jet Method to Create Zinc Nanoparticles and Study Their Structural and Optical Properties as an NH3 Gas Sensor

In this work, zinc nanoparticles were prepared using the low-temperature plasma method at different times 3 min, 5 min, 7 min, 9 min, where the initial reactions of zinc lead to the formation of nanoparticles. The metal interacts with the ionized plasma under different conditions and may turn into an oxide such as exposing the sample to air and raising the temperature of the solution a few degrees as a result of high voltage and within a certain range. The atmospheric pressure plasma system acts as the cathode, while the zinc metal strip acts as the anode. A series of techniques were used, including the use of X-ray diffraction (XRD), ultraviolet-visible spectroscopy and scanning electron microscopy (FESEM). The X-ray diffraction results showed that the samples have polycrystalline structures with hexagonal and cubic structures with a time difference, and the X-ray diffraction results showed the conversion of zinc particles into zinc oxides. FESEM images reveal particle size and shape. The ZnO nanoparticles prepared by the mentioned method seem to form different nanoshapes such as starfish and mushroom nanoparticles. The UV-visible results showed that the samples had an energy gap of about 3.4 eV at a time of 3 min, and this value decreases with increasing reaction time. The appearance of zinc oxides increases gradually with the passage of time. These results provide credibility for the fabrication of ZnO nanostructures for use in future gas sensing applications, despite the inhomogeneity of particle size among ZnO particles, the sensor was also fabricated to detect nitrogen gas (NH3) with different concentrations (17.25 ppm, 46.38 ppm, 78.58 ppm). at room temperature. The ZnO sample showed the highest sensitivity (88.1%) at 7 min. The sensitivity showed different results and increased with reaction time and gas concentration. However, response and recovery time are moderate and decrease as reaction time increases.

From disorder to order: A dynamic approach to mesophase formation in soft sphere model.

This study explores the dynamics of self-assembly and mesophase formation through molecular dynamics simulations of hexagonal and lamellar systems using a simplified coarse-grained model. We focus on characterizing the order-disorder transitions driven by temperature variations and emphasize the often overlooked disordered regime, which serves as a precursor to periodic mesoscale ordering. Our findings not only underscore the morphological richness of the disordered regime, comparable to that of its periodic counterparts, but also reveal the presence of clustering regimes within isotropic phases, thus corroborating prior experimental and theoretical observations. By employing the dynamic correlation coefficient, this work introduces a novel approach to understanding the fundamental mechanisms of mesophase formation, providing new insights into the complex dynamics of self-assembly.

Pressure-tuning of α-RuCl3 towards a quantum spin liquid

The layered material α-RuCl3 is a promising candidate to realize the Kitaev quantum spin liquid (QSL) state. However, at ambient pressure, deviations from the perfect Kitaev geometry prevent the existence of the QSL state at low temperatures. Here we present the discovery of a pressure-induced high-symmetry phase in α-RuCl3, which creates close to ideal conditions for the emergence of a QSL. Employing a novel approach based on Bragg and diffuse scattering of synchrotron radiation, we reveal a pressure-induced reorganization of the RuCl3-layers. Most importantly, this reorganization affects the structure of the layers themselves, which acquire a high trigonal symmetry. For this trigonal phase the largest ratio between the Kitaev (K) and the Heisenberg exchange (J) ever encountered is found: K/J = 124. Additionally, we demonstrate that this phase can also be stabilized by a slight biaxial pressure. This not only resolves the conflicting reports of low-temperature structures in the literature, but also facilitates the investigation of the high-symmetry phase and its potential QSL using a range of experimental techniques.

Effects of Gd on the microstructure and mechanical properties of GdxCoCrFeNiV0.4 high-entropy alloys

This study investigated the microstructure and mechanical properties of GdxCoCrFeNiV0.4 alloys. Various techniques such as XRD, SEM, EBSD, and TEM were utilized, alongside hardness and compression tests at room temperature. The findings revealed that the high-entropy alloy without Gd element exhibited a single face-centered cubic (FCC) phase. Upon the introduction of Gd element, the phase composition shifted to FCC + hexagonal structure (HS) phases, and further addition of Gd resulted in the presence of FCC + HS + body-centered cubic (BCC) phases. Additionally, the inclusion of Gd element led to the precipitation of Gd-rich particles within the alloy. The Vickers hardness test results revealed a significant increase in alloy hardness as the Gd content rose, from 177.5 HV for Gd0 to 848.4 HV for Gd0.4. This suggests that the presence of the HS phase and BCC phase notably influences alloy hardness. Furthermore, compressive test outcomes demonstrated that the alloy's yield strength rose from 173.74 MPa for Gd0 to 1356.17 MPa for Gd0.3 with increasing Gd content. However, the excessive addition of Gd elements results in significant precipitation of V and Cr elements, leading to grain coarsening, adversely affecting its mechanical properties. The high strength of Gd-containing high-entropy alloys can be attributed to various strengthening mechanisms, such as solid solution strengthening, the presence of the HS phase, the precipitation of a small number of Gd-rich particles, and the grain refinement caused by the addition of Gd.

Developing a novel calcium silver zeolite for caries management

ObjectiveTo develop a novel calcium silver zeolite (Ca-Ag-Zeo) and assess its biocompatibility, physiochemical properties and antimicrobial effects.MethodsCa-Ag-Zeo was synthesized using ion-exchange method with calcium chloride, silver nitrate and Zeolite X (Zeo). Silver zeolite X (Ag-Zeo) and Zeo were set as control. The chemical structure, morphology, crystal structure and elemental composition of Ca-Ag-Zeo was characterized by X-ray diffraction spectrum, scanning electron microscopy, transmission electron microscopy and energy dispersive spectroscopy, respectively. Its biocompatibility on the human gingival fibroblasts was assessed by cell counting kit-8 assay. Its physiochemical properties were determined by the released calcium and silver ion using Inductive Coupled Plasma Emission Spectrometry for up to 12 weeks. The antimicrobial properties on Streptococcus mutans, Lactobacillus acidophilus, Lactobacillus casei, and Candida albicans were assessed by minimum bactericidal concentration (MBC) or minimum fungicidal concentration (MFC) assay.ResultsCa-Ag-Zeo with a hexagonal cage structure was synthesized. As for biocompatibility, the half-maximal inhibitory concentration (± SD in mg/mL) of Ca-Ag-Zeo, Ag-Zeo and Zeo in human gingival fibroblasts were 0.52 ± 0.05, 0.15 ± 0.01 and 3.35 ± 0.58, respectively (Zeo > Ca-Ag-Zeo > Ag-Zeo; p < 0.05). As for physiochemical properties, the accumulated ion release (± SD in mg) of Ca-Ag-Zeo, Ag-Zeo and Zeo were 0.011 ± 0.003, 0 and 0 for calcium ion, respectively (Ca-Ag-Zeo > Ag-Zeo, Zeo; p < 0.001), and 0.213 ± 0.032, 0.209 ± 0.019 and 0 for silver ion, respectively (Ca-Ag-Zeo, Ag-Zeo > Zeo; p < 0.001). As for anti-microbial ability, the MBC/MFC (mg/mL) of Ca-Ag-Zeo, Ag-Zeo and Zeo were 32, 16 and > 256 against Streptococcus mutans; 32, 16, > 256 against Lactobacillus acidophilus; 16, 16, and 256 against Lactobacillus casei; 0.25, 0.125; and 2, 1, > 256 against Candida albicans, respectively.ConclusionA novel Ca-Ag-Zeo was developed. It presented better biocompatibility compared to Ag-Zeo. It released calcium and silver ions sustainably, and it could inhibit the growth of common cariogenic microorganisms.

Optimising Additive Manufacturing to Produce PLA Sandwich Structures by Varying Cell Type and Infill: Effect on Flexural Properties

The objective of this research is to optimize additive manufacturing processes, specifically Fused Filament Fabrication (FFF) techniques, to produce sandwich structures. Mono-material specimens made of polylactic acid (PLA) were produced, where both the skin and core were fabricated in a single print. To optimize the process, variations were made in both the base cell geometry of the core (Tri-Hexagon and Gyroid) and the core infill (5%, 25%, 50%, and 75%), evaluating their effects on static three-point bending behavior. Optical microscopy was employed to assess both the structure generated by additive manufacturing and the fracture modes. The findings reveal that increasing the infill, and thus the core density, enhances the mechanical properties of the structure, although the improvement is such that samples with 50% infill already demonstrate excellent performance. The difference between hexagonal and Gyroid structures is not significant. Based on microscopic analyses, it is believed that the evolution of 3D printers, from open to closed chamber designs, could significantly improve the deposition of the various layers.

High-pressure synthesis, structure and physical properties of two quasi-one-dimensional compounds Ba9Nb2.54Te15 and Ba9Ta1.89Te15

Two quasi-one-dimensional compounds Ba9Nb2.54Te15 and Ba9Ta1.89Te15 were synthesized under high pressure and high temperature conditions and systematically characterized by structural, transport and magnetic measurements. Both the two compounds crystallize into a hexagonal structure with the space group P-6c2 (No. 188). The structure consists of trimeric face-sharing octahedral Nb/TaTe6 chains separated by a large distance (>10 Å), thus presenting a strong one-dimensional crystal structure. The transport properties suggest that both the two compounds are semiconductors with a band gap ∼ 0.15 eV for Ba9Nb2.54Te15 and ∼ 0.22 eV for Ba9Ta1.89Te15. Magnetic properties characterization indicates that Ba9Nb2.54Te15 displays no long-range-order above 2 K, but with an effective moment μeff ∼ 1.8 μB/f.u., while Ba9Ta1.89Te15 exhibits a diamagnetic behavior. Our results demonstrate that, in the sequence of Ba9V3Te15, Ba9Nb2.54Te15 and Ba9Ta1.89Te15, the occupation in the transition metal sites decreases, the semiconducting band gap increases, and the magnetism changes from ferromagnetism to diamagnetism.

Revelation of the high surface insulation performance of the electron-delocalized group through molecule self-assembly on alumina insulator

Surface modification of vacuum insulators is a promising way to improve their surface insulation performance but commonly used surface modification technologies in surface insulation area such as fluorination and plasmas treatment are unable to control the surface chemical components at the molecular level, which makes it hard to explore molecular groups with high surface insulation performance. In this paper, molecule self-assembly is introduced to control the surface molecular structure precisely and vacuum surface insulation performance of a special molecular structure electron-delocalized group is studied. Hexagonal phenyl group containing delocalized electrons and cyclohexyl group with the same hexagonal molecular structure but without delocalized electrons are grafted onto the surface of alumina insulators through molecule self-assembly. Secondary electron emission yield test shows that phenyl group endows alumina insulators lower SEY than cyclohexyl group. Correspondingly, phenyl group grafted alumina insulators show higher surface insulation performance than cyclohexyl group. The results indicate that group containing delocalized electrons can endow insulators higher surface insulation characteristics.

Synthesis and characterization of fluorescent carbon dots obtained from citrus x sinensis by an eco-friendly method

The synthesis and characterization of fluorescent carbon dots (CDs) obtained by an environmentally friendly method through carbonization, fragmentation and centrifugation of orange peel (citrus x sinensis) are reported. By thermogravimetry, 4 degradation regions associated with hemicellulose, lignin and organic matter were found. The SEM micrograph shows a rough surface morphology with flakes and granulation due to the carbonization process. X-ray diffraction (XRD) shows a hexagonal crystalline structure associated with graphitic carbon, which was confirmed by Raman scatterings, Raman spectroscopy that presented two main vibrational bands, D and G, associated with active defects in the graphitic carbon crystalline structure. The Transmission electron microscopy (TEM) micrograph showed CDs of size 33.65 ± 0.68n, and with High-Resolution TEM (HRTEM) an interplanar distance of 0.213 nm in the direction of the crystal planes (100) of graphitic carbon was obtained, which were confirmed by XRD and Raman spectroscopy. X-ray photoelectron spectroscopy revealed the relative atomic composition and identified the strongest photoelectron transitions of carbon, sp2 (286 eV) and sp3 (285 eV), in graphitic carbon. Ultraviolet–visible (UV–Vis) spectroscopy of the CDs obtained from fragmentation graphitic carbon showed a band at 205 nm associated with CC bonds π-π* of CC and n-π*, as well as two bands at 276 and 328 nm associated with bond transitions. The Fourier Transform Infrared (FTIR) spectrum showed bands associated with CHs bonds as well as CC, CN bonds of the CDs. Fluorescence spectroscopy showed three emission bands at 2.43, 2.54 and 2.87 eV. The CDs showed the emission of the characteristic blue colour.

Interpenetrated Donor-Acceptor Heterojunctions in 2D Conjugated Dibenzo[g,p]chrysene-Based Kagome Covalent Organic Frameworks.

Dibenzo[g,p]chrysene can be viewed as a constrained propeller-shaped tetraphenylethylene with reduced curvature and has been utilized to construct dual-pore kagome covalent organic frameworks (COFs) with tightly packed two-dimensional (2D) layers owing to its rigid and more planar structural characteristics. Here, we introduce 2D COFs based on the node 4,4',4″,4‴-(dibenzo[g,p]chrysene-2,7,10,15-tetraphenyl)tetraamine (DBCTPTA) featuring extended conjugation compared to the dibenzo[g,p]chrysene-3,6,11,14-tetraamine (DBCTA) node. We establish two exceptionally crystalline imine-linked 2D COFs with a hexagonal dual-pore kagome structure based on the DBCTPTA core. The newly synthesized thienothiophene (TT) and benzodithiophene (BDT)-based DBCTPTA COFs show a tight stacking behavior between adjacent layers. Furthermore, we obtained an unprecedented, interpenetrated electron-donor/acceptor host-guest system with an electron-donating BDT DBCTPTA COF synthesized in situ with the soluble fullerene derivative [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) serving as molecular acceptor. The BDT DBCTPTA COF@PCBM film shows a much shorter amplitude-averaged PL lifetime of 7 ± 2 ps compared to 30 ± 4 ps of the BDT DBCTPTA COF film, indicating the light-induced charge transfer process. The successful in situ formation of interpenetrated donor-acceptor heterojunctions within 2D COFs offers a promising strategy for establishing D-A heterojunctions in diverse framework materials with open channel systems.