Increase In Height Research Articles

Wind Pressure of Low-rise Buildings Based on Wind-tunnel Numerical-simulation Test

Based on the numerical-simulation test data from the wind tunnel, the wind-pressure characteristics of low-rise buildings with gable roofs are examined and compared to standard values under different roof slopes, eave heights and terrains. To further investigate the underlying mechanisms of variation, a numerical-simulation study was conducted for selected conditions. The results indicate that when the roof slope is less than 3:12, the negative value of the shape coefficient for the windward roof of the building can reach up to -0.89, far exceeding the code value of -0.5. It is suggested that when the slope is not larger than 3:12, the shape coefficient for the windward roof should be -0.9 and the coefficient for the leeward roof should be determined through linear interpolation within the range from -0.4 to -0.75 based on the roof's slope size. With the increase of eave height and the decrease of ground roughness, the vortex intensity of the roof and the leeward surface increases and the area proportion of high negative pressure area in the vortex influence range increases. Thus, the negative value of the shape coefficient for the roof and the leeward surface becomes larger, which is higher than the code value. It is proposed that under an eave height of 12 m, the shape coefficient for the windward roof should be -0.95. Meanwhile, those of the leeward roof, leeward surface and sidewall 2 should be -0.6 under open terrain. Keywords: Low-rise buildings, Wind-tunnel test, Wind load, Shape coefficient, Numerical simulation

COMPATIBILITY STUDY OF HYDROCARBON RESINS WITH RUBBER COMPOUNDS FOR TIRE APPLICATIONS

ABSTRACT The addition of hydrocarbon resins to rubber compounds has a significant impact on their properties such as wet grip and rolling resistance. These performance characteristics have a strong correlation with the compatibility of the resin with the rubber matrix. Incompatible resins can cause excessive broadening of the damping curve, which results in poor rolling resistance. Compatibility, however, allows maximization of wet grip while minimizing the effect on rolling resistance. Compatibility is promoted by lower resin molecular weight and structural similarity to the polymers being blended. In this study, a method based on the Fox equation has been developed to quantitatively characterize the compatibility between resin and natural rubber (NR), a binary system. The dynamic shear rheometer (DSR), a tool new to the tire industry, is used to investigate the interaction between resin and two rubbers (i.e., a ternary system of NR–butadiene rubber [BR]–resin and solution polymerized styrene–butadiene rubber [SSBR]–butadiene rubber [BR]–resin), with a specific emphasis on resin partitioning among rubber blends. In addition, the DSR is applied to assess the Tg shift and tangent delta peak height, providing insight into the compatibility between rubbers and resin. A curve-fitting model was developed for the SSBR–BR–resin system to depict the relationship between these two parameters and the physical and chemical properties of resins, with the selection of resins featuring different degrees of aromaticity, Tg, and molecular weight. The findings indicated that higher Tg increased aromaticity and that lower molecular weight of the resin resulted in an elevated Tg shift in the blend, while lower molecular weight led to an increase in the tangent delta peak height. Our findings supply insight into the performance of rubber–resin blends and introduce a new screening tool for characterizing these blends in their green state.

Study on the impact of wave characteristics on the performance of full-scale tidal turbine

The operation of tidal turbines is inevitably influenced by waves, and extensive research has undoubtedly been conducted on this topic. However, most investigations of such studies have utilized small-scale turbines, with a primary focus on the load characteristics of the turbines themselves. There is a slight deficiency in attention to the wave characteristics that contribute to these loads. To bridge this gap, this study develops a computational fluid dynamics (CFD) model of a full-scale tidal turbine. The model's accuracy is assessed through flume experiments using a scaled-down version, validating the numerical approach against wave conditions. Employing actual tidal flow velocity and wave data as input, this study specifically examines how variations in wave period and height affect turbine performance. The analysis reveals a nuanced decrease in time-averaged performance with increases in wave period and height. Load fluctuations arise from wave impacts, turbine rotor rotation, and their interaction. With the increase in wave period or height, the fluctuations caused by the wave impacts and the interaction increase, while those induced by rotor rotation exhibit a slow growth trend but essentially remain stable.

Preliminary Exploration of Physiology and Genetic Basis Underlying High Yield in Indica–Japonica Hybrid Rice

The utilization of heterosis is of great significance in improving rice yield. To explore the physiological and genetic basis for high yield in indica–japonica hybrid rice, Zheyou18 (z18) and Yongyou12 (y12) were used as materials and compared with indica hybrid rice, Zheyou12 (z12); japonica hybrid rice, Liangyoupeijiu (LYPJ); and the conventional lines zhe04B (04B) and zhehui818 (h818) under seedling growth vigor, functional leaf morphology, chlorophyll content, yield component, panicle trait, and InDel heterosis analysis. Z18 and y12 showed the largest increase in plant height 6 d and 9 d after germination; the root dry weight of z18 was 31.2% and 42.0% higher than its parents on the 12th d. The length of functional leaves ranked in the middle, while the width was the largest, resulting in z18 and y12 having the largest leaf area. Yield components showed that z18 and y12 had the highest number of primary branches, spikelets, and grains, and grain yield, which was 58.1 g in z18, increased by 29.8% and 8.7%, respectively, in comparison with h818 and LYPJ. The InDel genetic distance was significantly positively correlated with single spike weight, with r reaching 0.771, making it the only consistent and most correlated among the seven traits. Therefore, we speculated that as the InDel genetic distance expands, heterosis mainly manifests in the increase in single spike weight. This study comprehensively explored the physiological mechanism of yield improvement in indica–japonica-hybrid rice and used InDel genetic distances to study the genetic basis of heterosis, which will be helpful for future rice yield improvement.

Aerosol influence on cloud macrophysical and microphysical properties over the Tibetan Plateau and its adjacent regions.

This study uses aerosol optical depth (AOD) and cloud properties data to investigate the influence of aerosol on the cloud properties over the Tibetan Plateau and its adjacent regions. The study regions are divided as the western part of the Tibetan Plateau (WTP), the Indo-Gangetic Plain (IGP), and the Sichuan Basin (SCB). All three regions show significant cloud effects under low aerosol loading conditions. In WTP, under low aerosol loading conditions, the effective radius of liquid cloud particles (LREF) decreases with the increase of aerosol loading, while the effective radius of ice cloud particles (IREF) and cloud top height (CTH) increase during the cold season. Increased aerosol loading might inhibit the development of warm rain processes, transporting more cloud droplets above the freezing level and promoting ice cloud development. During the warm season, under low aerosol loading conditions, both the cloud microphysical (LREF and IREF) and macrophysical (cloud top height and cloud fraction) properties increase with the increase of aerosol loading, likely due to higher dust aerosol concentration in this region. In IGP, both LREF and IREF increase with the increase in aerosol loading during the cold season. In SCB, LREF increases with the increase in aerosol loading, while IREF decreases, possibly due to the higher hygroscopic aerosol concentration in the SCB during the cold season. Meteorological conditions also modulate the aerosol-cloud interaction. Under different convective available potential energy (CAPE) and relative humidity (RH) conditions, the influence of aerosol on clouds varies in the three regions. Under low CAPE and RH conditions, the relationship between LREF and aerosol in both the cold and warm seasons is opposite in the WTP: LREF decreases with the increase of aerosol in the cold season, while it increases in the warm season. This discrepancy may be attributed to a difference in the moisture condition between the cold and warm seasons in this region. In general, the influence of aerosols on cloud properties in TP and its adjacent regions is characterized by significant nonlinearity and spatial variability, which is likely related to the differences in aerosol types and meteorological conditions between different regions.

The Effect of Supplementation with Organic Acid and Oregano Oils in Drinking Water on Pekin Duck Growth and Welfare

This study evaluated duck growth, health, and welfare in response to water supplementation with organic acid (OA) and oregano oils (OOs) in Pekin duck. The treatments used in this study included a control (CON) treatment with no water additives given, an OA treatment (ProPhorce Exclusive NC®), and an OO treatment (Nubiotic 4X Concentrate®). The OA and OO improved the feed conversion ratio (FCR) and body weight (BW) (p < 0.01) compared to the control (CON). Both OA and OO showed differences (p < 0.05) in villus height and crypt depth compared to the CON. But only OA showed an increase (p < 0.01) in villus height and villus height/crypt depth ratio. On D 35, the total plasma corticosterone levels, heterophil-to-lymphocyte ratios, and asymmetry scores for OA and OO were decreased (p < 0.05) compared to CON, indicating lower stress susceptibility. The pH levels of OA ceca and jejunum were lower (p < 0.05) compared to CON. Tibia breaking strength was increased (p = 0.02) for OA compared to CON, while no differences were found with OO (p > 0.05). In conclusion, these experiments indicate that OA and OO can be used to improve duck growth, feed efficiency, stress susceptibility, and bird welfare.

A new method of mining pressure control for roof cutting in advance working face

After the extraction of deep coal resources, the original stress state is disrupted, leading to increased abutment stress ahead of the working face. This heightened pressure causes significant deformation in the roadway preceding the working face. To tackle this issue, a pioneering method called Roof Cutting in Advance of the Working Face(RCAWC) has been introduced to mitigate deformation by proactively alleviating pressure. This method leverages the principle of conservation of energy within the rock mass system, augmenting the fragmentation energy of the roof rock mass through controlled blasting. This process aims to release the accumulated energy within the rock mass, thereby reducing pressure. This research not only elucidates the mechanism employed by RCAWC to counteract mining pressure but also delineates the evolving pattern of bearing pressure at various RCAWC heights. The findings reveal a shift in the abutment stress curve from a single-peaked to a double-peaked pattern after roof cutting. Notably, there is a significant reduction in abutment stress as the RCAWC height increases. However, as the thick roof is cut off, the negative correlation effect diminishes. Subsequently, an engineering implementation was carried out. Following the adoption of RCAWC technology, roadway deformation decreased by 63.6 % to 75 %, and the size of the protective coal pillar reduced by approximately one-third. These findings underscore the remarkable effectiveness of RCAWC technology in impeding the propagation of mining pressure towards roadways, reducing the extent of abutment stress, and ultimately alleviating stress and deformation within the surrounding rock formation.

A Base Layer of Ferrous Sulfate-Amended Pine Bark Reduces Phosphorus Leaching from Nursery Containers

Phosphorus (P) fertilizers applied to container-grown nursery crops readily leach through pine bark-based substrates and can subsequently runoff and contribute to surface water contamination. The objectives of this research were to determine the effect of adding a layer of FeSO4·7H2O-amended pine bark (FSB) to the bottoms of nursery containers on P leaching characteristics. Phosphorus and iron (Fe) leaching in response to FSB layer height (4 or 7.5 cm), FeSO4·7H2O rate (0.3, 0.6, or 1.2 kg·m−3 Fe), and form (i.e., granular versus liquid) used to formulate the FSB layer, and the inclusion of dolomite in the FSB layer were also investigated. Greenhouse studies lasting 15 and 19 weeks were conducted, in which 2.5 L nursery containers containing the FSB layer treatments below non-amended pine bark substrate were fertilized with 199 or 117 mg P from a soluble or controlled-release fertilizer, respectively. Leachate resulting from daily irrigation was collected and analyzed for P and Fe weekly. All FSB treatments leached less P than the control (non-amended pine bark only), with P reductions ranging from 22% (4 cm FSB with 0.3 kg·m−3 Fe) to 73% (7.5 cm FSB with 1.2 kg·m−3 Fe). Phosphorus leaching decreased linearly with an increase in Fe rate or layer height. The amount of Fe that leached from containers with FSB was <5% of that applied, regardless of the Fe rate. Granular- and liquid-applied FeSO4·7H2O with or without dolomite were equally effective at reducing P leaching. Adding 0.6 kg·m−3 Fe to the bottom 500 cm3 of pine bark increased P adsorption by 0.053 mg·cm−3 P, which equates to 17.9 mg P adsorbed per gram of FeSO4·7H2O added. Results from this research suggest that including an FSB layer in the bottom of nursery containers is an effective strategy for reducing P runoff from container-based nursery production sites.

Potencial Simbiótico de Microrganismos do Solo na Promoção do Crescimento de Espécies Arbóreas da Mata Atlântica

The objective of this study was to evaluate the potential of topsoil obtained from a natural forest fragment in the Brazilian Atlantic Forest to serve as a source of symbiotic microorganisms capable of promoting the growth of native tree species in ecological restoration projects. In greenhouse conditions, 14 experiments in a completely randomized design were conducted in 1,700 cm³ pots filled with sterilized substrate. The effect of adding 80 g of topsoil, either in natura or sterilized, to the substrate was tested on the growth of 14 tree species. Plant height, stem diameter, mycorrhizal colonization and dry masses of shoot, roots, and nodules of tree species were measured. Applying the topsoil to the pots generally resulted in significant increases in height and stem diameter of seedlings compared to the control group during the four to six-month evaluation period. This effect was particularly greater in the nodulating species Plathymenia reticulata, Dalbergia nigra and Mimosa bimucronata, with increases in height and stem diameter of up to 328% and 484%, respectively. Forest topsoil also had a positive impact on the growth of shoot, roots, and nodules of the plants, significantly differing from the control groups. Only the plants that received the topsoil in natura exhibited mycorrhizal colonization and the formation of nodules in nitrogen-fixing species. These plants that established mycorrhizas and nodules presented higher concentrations of phosphorous and nitrogen in their biomass, respectively. Under controlled conditions, the use of forest topsoil proved to be a promising strategy for the introduction of microorganisms that can enhance the growth of tree species, thereby holding potential for implementation in nurseries and field settings.
 

EFFECT OF OKORO [(Albizia zygia (J.F.) Macbr)] LEAFY BIOMASS AND NPK FERTILISER ON THE GROWTH AND YIELD OF SWEET PEPPER (Capsicum annum L.)

Agricultural productivity and sustainable crop management are pivotal aspects of global food security and economic stability. The quest for efficient and environmentally friendly practices in crop production has led to a surge in research exploring the utilisation of organic materials alongside conventional fertilisers to enhance crop growth and yield. An experiment was conducted over a growing period of three months, starting in August 2023 at the research field of Kwame Nkrumah University of Science and Technology, Kumasi-Ghana, to investigate the effects of Albizia zygia leafy biomass in combination with NPK fertiliser on the growth and yield of sweet pepper (Capsicum annum L.). A randomised complete block design was employed with four treatment groups replicated four times, including various combinations of A. zygia leafy biomass and NPK fertiliser, alongside control groups of sole fertiliser application and untreated plots (T1). The treatments were as follows: T1 = No biomass, no NPK (control); T2 = 0.5348 kg of A. zygia leafy biomass per 4.86 m2 (1100.5 kg/ha of A. zygia leafy biomass); T3 = 0.2463 kg of NPK per 4.86 m2 (506.7 kg/ha of NPK); and T4 = 0.2674 kg of A. zygia leafy biomass per 4.86 m2 + 0.1231 kg of NPK (550.3 kg/ha of A. zygia leafy biomass + 253.4 kg/ha of NPK). The assessed parameters were plant height, number of leaves, number of branches, fruit yield and fresh fruit weight. Significant variations (p ˂ 0.05) were observed in the growth parameters (plant height, number of leaves, number of branches) and yield attributes (fruit yield and fresh fruit weight) of sweet pepper among the treatments. The combined application of A. zygia leafy biomass and NPK fertiliser (T4) exhibited increased effects on plant height, number of leaves, number of branches, fruit yield and fresh fruit weight compared to individual treatments and control groups (p ˂ 0.05). Notably, the treatment combining A. zygia leafy biomass and NPK fertiliser (T4) demonstrated a substantial increase in plant height (44.58 cm), a significant improvement in the number of leaves (42.98) and a remarkable enhancement in the number of branches (11.33) compared to the sole applications and the control group. Furthermore, the combined treatment significantly increased (p ˂ 0.05) the yield parameters, including fruit yield and fresh fruit weight per hectare, showcasing an increase of 8796/ha and 23.91 t/ha, respectively, compared to sole fertiliser application and the control. The findings from this study demonstrated that the incorporation of A. zygia leafy biomass, either solely or in combination with NPK fertiliser, positively impacted the growth and yield of sweet pepper plants. These results highlight the potential of A. zygia leafy biomass as a valuable organic amendment for sustainable and enhanced crop production, offering promising implications for agricultural practices aimed at improving yield and plant growth.

Redox priming could be an appropriate technique to minimize drought-induced adversities in quinoa.

The exogenous use of the redox compound (H2O2) plays a significant role in abiotic stress tolerance. The present study investigated various H2O2 application methods (seed priming, foliar spray, and surface irrigation) with varying concentration levels (0 mM, 5 mM, 10 mM, 15 mM, 40 mM, 80 mM, and 160 mM) to evaluate the efficiency of supplying exogenous H2O2 to quinoa under water-deficit conditions. Drought stress reduced quinoa growth and yield by perturbing morphological traits, leading to the overproduction of reactive oxygen species and increased electrolyte leakage. Although all studied modes of H2O2 application improved quinoa performance, surface irrigation was found to be sensitive, causing oxidative damage in the present study. Seed priming showed a prominent increase in plant height due to profound emergence indexes compared to other modes under drought conditions. Strikingly, seed priming followed by foliar spray improved drought tolerance in quinoa and showed higher grain yield compared to surface irrigations. This increase in the yield performance of quinoa was attributed to improvements in total chlorophyll (37%), leaf relative water content (RWC; 20%), superoxide dismutase (SOD; 35%), peroxidase (97%), polyphenol oxidase (60%), and phenylalanine ammonia-lyase (58%) activities, and the accumulation of glycine betaine (96%), total soluble protein (TSP; 17%), proline contents (35%), and the highest reduction in leaf malondialdehyde contents (MDA; 36%) under drought stress. PCA analysis indicated that physio-biochemical traits (proline, SOD, TSP, total chlorophyll, MSI, and RWC) were strongly positively correlated with grain yield, and their contribution was much higher in redox priming than other application methods. In conclusion, exogenous H2O2 application, preferably redox priming, could be chosen to decrease drought-induced performance and yield losses in quinoa.

Utilization of Eggshell-Derived Calcium Carbonate as an Eco-Friendly Fertilizer Enhancing Growth of Rosa Abientina, Rosa, and Fragaria × ananassa, and Soil Health

This research paper investigates the potential of eggshells as an eco-friendly fertilizer for enhancing the growth of Fragaria Ananassa (commonly known as strawberry), Rosa Abientina, and Rosa while also exploring its influence on soil microbial dynamics through calcium carbonate enrichment. The study employs a multifaceted approach, integrating greenhouse experiments and soil analyses to comprehensively assess the impact of eggshell-derived calcium carbonate on plant physiology and soil microbial communities. The findings aim to contribute valuable insights into sustainable agricultural practices and the utilization of organic waste materials for improved crop cultivation. Eggshell-derived calcium carbonate emerges as a compelling solution for environmentally mindful fertilization, offering multifaceted benefits in enhancing plant growth and fortifying soil health. By controlling the potential of kitchen waste repurposing, farmers can revolutionize agricultural practices, concurrently improving soil fertility while mitigating waste accumulation. This study's insights underscore the transformative potential of eggshell-based fertilizers, not only in optimizing agricultural productivity but also in fostering a sustainable approach to food production. Furthermore, the experimental findings reveal promising results, especially with species such as Rosa Abientina, Fragaria Ananass, and Rosa, where all three species showed a significant increase in height after being treated with powdered eggshells. This underscores the efficacy of eggshell-derived calcium carbonate in promoting robust growth across diverse plant species. Embracing these innovations holds promise for addressing the pressing challenges of environmental sustainability and global food security, marking a significant stride towards a more resilient and resource-efficient agricultural ecosystem.

Multi-Parameter Inversion Optimization for Transverse Rib Profile Enhanced Convective Heat Transfer

The convective heat transfer performance of the rib-element approach in the channel is influenced by the transverse rib profile. In present work, a nonlinear multi-parameter optimization method based on inversion optimization is proposed and further used to obtain the optimal rib profile in a rectangular channel. Firstly, four conventional profiles as the original ribbed channel were selected to obtain the convective heat transfer performance of the channel by experiment and numerical solution; secondly, several control points were selected along the profile, and the polar radius was updated, and curve fitting was carried out. The results show that the inversion optimization can optimize the rib profile to improve the convective heat transfer performance. As the number of control points increases, the optimized profile changes hardly. The inversion optimization yields a similar optimized profile regardless of the original rib profile. With the increase of original rib height, the enhanced heat transfer performance of optimized profile is better. For the ribbed channel with original height 0.4 × channel height, as the Reynolds number increases from 6000 to 33,000, the performance evaluation criteria of the optimized profile increase by 14.94% to 21.2% compared with the original triangular profile.

Longitudinal Analysis of Latvian Child Growth: Anthropometric Parameters Dynamics from Birth to Adolescence.

This study provides a comprehensive analysis of the physical development patterns from birth to adolescence, utilizing a longitudinal dataset of 70 children monitored from birth until 17 years of age. The research focuses on the variability of growth trajectories, emphasizing the role of genetic and environmental factors in influencing these patterns. Key findings indicate that most children undergo one or two periods of accelerated growth, with significant variability in the timing and magnitude of these growth spurts. The study also highlights the adaptive nature of growth changes over generations, influenced by ecological, nutritional, and socio-economic conditions. The longitudinal approach reveals critical insights into the timing of peak growth velocities, demonstrating that girls reach their growth peak approximately one year earlier than boys. The analysis of intergenerational growth patterns suggests a significant increase in average height over the century, attributed to genetic diversity and changes in lifestyle and nutrition. This study's findings emphasize the importance of updating physical development standards regularly to reflect the changing genetic and environmental landscape. The variability in growth patterns and their correlation with health outcomes in later life highlights the need for targeted public health strategies that address the underlying socio-economic and environmental determinants of health. This research contributes to the understanding of physical development trajectories and provides a foundation for future studies aimed at optimizing health outcomes from early childhood through adolescence. The primary objective of this article is to meticulously analyze the dynamics of height growth and accurately identify the periods of accelerated bodily development within the context of longitudinal research.

Effects of Humic Acids on Calorific Value and Chemical Composition of Maize Biomass in Iron-Contaminated Soil Phytostabilisation

An interesting feedstock for energy purposes is plant biomass due to its renewability, widespread availability and relatively low cost. One plant with a high and versatile use potential is maize. Plants used for energy production can be grown in polluted areas, e.g., with iron. The aim of the study was to determine the effect of humic acids (HAs) on the yield, calorific value and other energy parameters and chemical composition of maize biomass applied as a phytostabiliser on iron-contaminated soil. The soil was contaminated with iron at 0, 250, 500 and 750 mg kg−1. The HAs were added to the soil in the following amounts: 0, 0.3, 0.6 and 0.9 g kg−1 of soil. Soil contamination with iron had relatively little effect on the heat of combustion and calorific value of biomass and very strongly reduced plant height (42%), dry matter yield (95%) and energy production of maize biomass (90%), the SPAD index at the fifth leaf unfolded stage (44%) (as opposed to the stem elongation stage), sodium, magnesium and phosphorus contents, and increased calcium, potassium and nitrogen contents of maize. The application of HAs to the soil had a positive and very large effect on both the height and biomass parameters studied, resulting in an increase in plant height (22%), dry matter yield (67%) and energy production from maize biomass (62%). Changes in the heat of combustion and calorific value of the biomass were minimal but positive. HAs contributed to a decrease in the value of the SPAD index during the stem elongation phase of maize and in the content of all macronutrients in maize biomass as a result of a reduction in the effect of iron on macronutrient content and to a significant increase in maize dry matter yield in plots with their application. The application of HAs appears to be an effective adjunct in the phytostabilisation of iron-contaminated soils by growing crops for energy purposes.

3D Weight-Bearing CT Imaging Analysis of Foot Mechanics: Bridging High Heels and Hallux Valgus

Introduction/Purpose: Evidence in the literature suggests the negative effects of using High Heels (HH), becoming a challenge for clinicians and researchers since they are welcomed by women worldwide, mainly due to the subjective power of attractiveness given to them. Although some people blame HH as one of the causes of Hallux Valgus (HV), until now, there are no studies in the literature that effectively prove a cause-effect relationship between HH and HV. The objectives of this study are: (1) to analyze whether the increase in heel height can lead to HV and (2) to evaluate whether HV can increase in severity with increasing heels. We hypothesized that an increase in heel height could cause and increase the severity of HV deformity. Methods: Comparative cross-sectional study. Forty-one feet from twenty-one participants (11 males and 10 females, aged 30.8 ± 8.9 years, and with Body Mass Index 25.5 ± 2.0 m kg2) were recruited. HH shoes were designed for this study with three heights for each participant: 3, 6, and 9 cm. The inclusion criteria were: no regular wearing of heels. The exclusion criteria were: Hallux Valgus diagnosis and/or any orthopedic conditions that affect the Foot and Ankle joints. Hallux Valgus Angle (HVA), Intermetatarsal Angle (IMA), First-Metatarsal Phalangeal Angle, 1st-to-5th Intermetatarsal Angle, First Tarsometatarsal Angle (axial), Second tarsometatarsal angle (axial), Hindfoot Moment Arm (HMA) (mm), Saltzman 45 angle and, Foot Ankle Offset (FAO) were measurement using semiautomated software analysis. Multiple comparisons were performed (Bonferroni's for normal distributions and Wilcoxon test for no normal distributions) when there was a main effect on an outcome (p < 0.05). Results: With the increase in HH, we noticed a progressive increase in HVA (p < 0.001), IMA (p < 0.001), First-Metatarsal Phalangeal Angle (p < 0.001), First Tarsometatarsal Angle (axial) (p < 0.001), and the Second tarsometatarsal angle (axial) (p < 0.001). The Hindfoot Moment Arm (HMA) (mm), Saltzman 45 angle, and Foot Ankle Offset (FAO) had hindfoot varization behavior. When we stratified the groups and compared them, we noticed that an increase of 3 cm in heels slightly increased HVA and IMA (p > 0.05). However, heel increases above 6 cm significantly increased HVA and IMA (p > 0.001). Based on Coughlin's classification, a 3 cm heel increase promoted a mild HV and increases above 6 cm caused a moderate HV. Conclusion: Based on data from our study with patients without Hallux Valgus through analysis with WBCT versus high heels, we conclude that increasing heel height can lead to Hallux Valgus and can progressively increase the severity with increasing high heels. High heels above 6 cm can lead to moderate Hallux Valgus. These findings may be an essential step toward a better understanding of the effects of increasing high heels on Hallux Valgus pathology.

Impact of protein and carnitine consuption on outcomes of care development of full-term newborns with critical perinatal diseases

There were studied results of the impact of increased consumption of proteins and L-carnitine in the nutrition program of full-term newborns with perinatal diseases on the results of physical development and inpatient treatment features. The purpose of the work was to study the correlations between short-term higher consumption of protein and carnitine by full-term newborns and the results of their physical development, the duration of hospital care development. The vital signs of 59 full-term newborns were studied in a randomized controlled trial in the period 2017-2020. The main critical disease of the perinatal period in newborns of both groups was found to be hypoxic-ischemic encephalopathy of a moderate degree in 86.7% and 86.2%, without a statistically significant difference. One group (n=30) received nutrition with mother's milk or formula, the second group (n=29) received similar nutrition with fortification with a protein and L-carnitine supplement during the hospital stay. At the beginning and at the end of the treatment, physical development of the newborns was studied and correlations between the obtained data were investigated. Newborns of both groups did not differ in characteristics at the beginning of the study. The proportions of the newborns' weight corresponded to the limits of the 50% percentile. The group with increased consumption of protein and carnitine, fortification group (FG) demonstrated better indicators of physical development, they regained body mass faster. Body mass of the newborns of the fortification group goup was 3966.9±439.1 g, compared to the standard nutrition (SN) group, with indicators being 3554.6±452.3 g, at p=0.003. The rate of increase in body length in FG was twice that of the SN group. Consumption of a larger dose of protein was accompanied by a shorter stay in the intensive care unit – 10.0 (8.0; 12.0) days versus 12.0 (11.0; 16.0) days, with U=235.0; p=0.002; earlier discharge from the hospital – 21.0 (19.0; 27.0) days versus 26.5 (22.0; 31.0) days, with U=267.0, p=0.01. Carnitine supplementation in the FG group led to an increase in the level of free carnitine in the blood plasma samples taken before the discharge from the hospital. The study of correlations revealed a positive correlation between the consumption of a full dose of proteins and the total increase in height (R=0.3, p<0.05), the increase in body weight (R=0.3, p<0.05). A negative correlation was found between the protein level and the duration of treatment in the hospital (R= -0.3, p<0.05). The level of free carnitine had a positive effect on the increase in body length (R=0.51, p<0.05), daily weight gain (R=0.3, p<0.05). A poor increase in body length was associated with a longer duration of respiratory support: the correlation had an inverse direction R= -0.4, p<0.05. Improving nutritional strategies has significant prospects for improving care development of full-term babies with critical perinatal states.

Effect of Plant Density on Mechanical Harvest Efficiency of New Mexico Pod-type Green Chile Pepper

Summary. New Mexico green pod-type chile (Capsicum annuum) has significant importance as a vegetable crop. The cultivation and trade of New Mexico pod-type green chile are culturally significant within New Mexico (USA) and contribute to the state’s economy by providing income and employment to farmers and through supporting industries. However, because of the high cost and limited availability of labor, New Mexico pod-type green chile acreage has declined. Traditionally, New Mexico pod-type green chile is hand-harvested when the fruit are full-size but physiologically immature. To preserve and expand the production of New Mexico pod-type green chile, the adoption of mechanical harvest technologies is essential. In 2015 and 2016, experiments were conducted at New Mexico State University’s Los Lunas Agricultural Science Center (Los Lunas, NM, USA) to examine the effects of increased planting density on New Mexico pod-type green chile fruit size, plant architecture, and mechanical harvest efficiency. Two commercial New Mexico pod-type green chile cultivars, NuMex Joe E. Parker and AZ-1904, were direct-seeded on 17 Apr 2015 and 14 Apr 2016. On 11 Jun 2015 and 14 Jun 2016, three plant density treatments were implemented at 39,000 (high), 23,000 (medium), and 15,000 (standard) plants/acre. Before harvest, plant measurements, including height, width, height to first bifurcation, stem diameter, and number of lateral basal branches, were obtained. Plots were mechanically harvested using an inclined double helix harvester, and harvested material was sorted into marketable green fruit, machine-broken fruit, and nonpod plant material. Fruit measurements, including fruit weight, width, length, pericarp thickness, and number of locules, were obtained. Both cultivars exhibited a 9% increase in height to bifurcation accompanied by fewer basal branches grown at high density. Plant density did not significantly affect the fruit length, width, number of locules, and pericarp thickness. Plants grown at high density had an increased percentage of marketable fruit, with ‘NuMex Joe E. Parker’ having a higher percentage of marketable green fruit compared to ‘AZ-1904’. The results demonstrated that an increase in planting density in production fields to 39,000 plants/acre coupled with cultivar selection enhanced efficiency in a mechanical harvest system.

Amelioration of growth of maize (Zea mays L.) seedling using plant growth promoting bacteria

This research was aimed to screen plant growth promoting bacteria (PGPB) from soil and study its effect on maize plant growth. PGPB were isolated from Saurashtra coastal region soil and cultured in Nitrogen fixing Ashby’s medium to find potent of PGPBs, we conducted a thorough screening process, assessed their abilities in phosphate and zinc solubilization, siderophore production, hydrogen cyanide (HCN) release and the antifungal activity was performed against Fusarium oxysporum, a pathogenic fungus. These tests helped us identify bacteria with plant growth-promoting characteristics for plants. Bacterial isolates which provided better results were sequenced and sequences were submitted to NCBI. Bacterial isolates selected for application on maize in primary screening showed most treated seeds increased the seedling vigor of maize. In the latter stages of screening where bacterial consortia were developed from primary and secondary screening. In 30 days, the experiment in maize plant height, number of leaves, chlorophyll content and anatomy was analysed. All the bacterium consortiums displayed an increase in height (24.75%), number of leaves (47.77%) and total chlorophyll content (23.59%) as compared to the control maize plant. Additionally, microscopic examination of the treated plants showed improved growth, especially in the increased starch grain content in the leaves, stems and roots. Out of the eleven PGPB consortia, 3 specific PGPB consortia in this study have significantly substantiated the growth of maize plants as evidenced by the comprehensive analysis of anatomical features.

Comparison of ZnO-based varistor performance by doping Zn–Sb–O phase and Sb2O3 respectively

In this study, ZnO–Bi2O3–Cr2O3–MnO2–B2O3 (ZBCMB) varistors were made by doping Zn–Sb–O phase and Sb2O3 phase in low-temperature respectively. Compared with the Sb2O3 doped sample, the breakdown field strength (E1mA) was effectively reduced from 605.36 V/mm to 440.24 V/mm due to the doping of Zn–Sb–O phase. The trend of the nonlinear coefficient α is similar for Sb2O3 and Zn–Sb–O doping, although Zn–Sb–O doping leads to a higher α = 64. This is due to the fact that the preparation of Zn–Sb–O phase avoids the oxygen vacancy reduction effect caused by the direct reaction of Sb2O3 with Bi2O3. The doping of Zn–Sb–O effectively increases the concentration of adsorbed oxygen, which has a very large positive effect on the formation of interfacial states and the increase of the potential barrier height.