Heavy Metals Research Articles

Smartphone-assisted colorimetric sensor arrays based on nanozymes for high throughput identification of heavy metal ions in salmon

The rapid, precise, and high-throughput identification of multiple heavy metals ions holds immense importance in ensuring food safety and promoting public health. This study presents a novel smartphone-assisted colorimetric sensor array for the rapid and precise detection of multiple heavy metals ions. The sensor array is based on three signal recognition elements (AuPt@Fe-N-C, AuPt@N-C, and Fe-N-C) and the presence of different heavy metal ions affects the nanozymes-chromogenic substrate (TMB) catalytic color production, enabling the differentiation and quantification of various heavy metal ions. Combined with a smartphone-based RGB mode, the colorimetric sensor array can successfully identify five different heavy metal ions (Hg2+, Pb2+, Co2+, Cr6+, and Fe3+) as low as 0.5 μM and different ratios of binary and ternary mixed heavy metal ions in just 5 min. The sensor array successfully tested seawater and salmon samples with a total heavy metal content of 10 μM in the South China Sea (Haikou and Wenchang). Overall, this study highlights the potential of smartphone-assisted colorimetric sensor arrays for the rapid and precise detection of multiple heavy metal ions, which could significantly contribute to food safety and public health monitoring.

Pollution Characteristics and Risk Assessment of Heavy Metals in the Soil of a Municipal Solid Waste Landfill Site

ABSTRACT With the excavation of landfill sites, the disposal and reduction of organic-rich soils with high proportions of heavy metals have become urgent issues. This study focuses on the pollution characteristics and ecological risks associated with heavy metals in the humus soil of a municipal solid waste (MSW) landfill. The results indicate that the concentrations of heavy metals in the humus soil followed the sequence of Cu > Zn > Cr > Pb > Ni > As > Cd > Hg, and Cu and Cd exhibited the highest exceedance multiples. Except for Cr, the concentrations of the heavy metals in the humus soil were higher than those in combustible components, with a strong Hg correlation. Heavy metal forms indicate varying degrees of mobility and stability; Cr, As, Hg, and Pb were stable, while Ni, Cd, Cu, and Zn showed higher mobility. The results of the principal component analysis reveal that heavy metals primarily originate from industrial and agricultural waste. Finally, the geoaccumulation index of the metals indicated that Cu, Zn, Cd, and Pb exhibited severe contamination. Most importantly, Cd posed the greatest environmental risk as it has the highest effective content, bioavailability, and mobility. This study provides a scientific foundation for mitigating heavy metal pollution in the humus soil of landfill sites.

Heavy metal changes related to land use changes in a karst area: a case study in Changshun, Guizhou Province, China

Karst areas are often characterized by fragile ecological systems, and environmental pollution has increased the pressures on people living in such regions. This study aimed to investigate the status of pollution caused by heavy metals (Pb, Cd, Hg, As, and Cu) in soils based on different land uses in Changshun County, a karst area in southwestern China. Soil samples were collected from natural forestlands (NFLs), natural brush lands (NBLs), natural pasture lands (NPLs), artificial forestlands (AFLs), artificial brush lands (ABLs), and artificial pasture lands (APLs) for evaluation. The results suggest that the soil profile characteristics of the heavy metals studied herein vary significantly among different land uses. The heavy metal concentrations in all soil samples collected from NFLs were lower than those in samples from other land uses. Forest trees can protect soil from heavy metal pollution caused by atmospheric deposition; this is especially true for Hg. In cultivated forestlands and brush lands, special attention should be devoted to Cd pollution in the soil, which may be caused by the use of fertilizers. Changing both natural and artificial pastoral lands to forestlands could benefit the local ecosystems as it may reduce Hg contamination.

Land-Use Pattern-Based Spatial Variation of Physicochemical Parameters and Efficacy of Safe Drinking Water Supply along the Mahaweli River, Sri Lanka

Exploration of the pollution status of river-based water sources is important to ensure quality and safe drinking water supply for the public. The present study investigated physicochemical parameters of surface water in the upper segment of River Mahaweli, which provides drinking water to the Nuwara Eliya and Kandy districts of Sri Lanka. River surface water from 15 intakes and treated water from 14 Water Treatment Plants (WTPs) were tested for pH, water temperature, turbidity, EC, COD, 6 anions, 21 cations, 3 pesticides, and 30 antibiotics once every 3 months from June 2022 to July 2023. Except for turbidity and iron concentrations, all other parameters were within the permissible range as per the Sri Lanka Standard Specification for Potable Water (SLS 614:2013). The uppermost Kotagala WTP raw water had a high concentration of iron due to runoff from areas with abundant iron-bearing minerals. Turbidity increased as the river flowed downstream, reaching its highest value of 13.43 NTU at the lowermost Haragama. Four intakes had raw surface water suitable for drinking as per the Water Quality Index (WQI). Pollution increased gradually towards downstream mainly due to agricultural runoff, industrial effluents, and urbanization. Poor water quality at the upstream Thalawakale-Nanuoya intake was due to highly contaminated effluent water coming from Lake Gregory in Nuwara Eliya. Cluster analysis categorized WTP locations in the river segment into 3 clusters as low, moderate, and high based on contaminations. Principal component analysis revealed that the significance of the 41.56% variance of the raw water was due to the pH and the presence of heavy metals V, Cr, Ni, Rb, Co, Sr, and As. All treated water from 15 WTPs had very good to excellent quality. In general, heavy metal contamination was low as indicated by the heavy metal pollution index (HPI) and heavy metal evaluation index (HEI). The treatment process could remove up to 94.7% of the turbidity. This is the first attempt to cluster the river catchment of the Mahaweli River based on physicochemical parameters of river water. We present here the land-use pattern-based pollution of the river and efficacy of the water treatment process using the Mahaweli River Basin as a case study. Regular monitoring and treatment adjustments at identified points are recommended to maintain the delivery of safe drinking water.

Multidimensional Approach for the Assessment of Environmental Pollution and Health Risk Associated With V, Ni, Cr, Cu, and Zn in the Recent Sediments of Kabini Interstate River, Southeastern Western Ghats, India

ABSTRACTThe present work intends to study the variation of heavy metals (HMs) to scrutinize the scenario of pollution index and associated environmental risk, as well as source weathering conditions along the Kabini River. The decreasing order of concentration of HMs along the basin is Cr > V > Ni > Zn > Cu. The paper spotlights the pollution grade in sediments, assessed by the geo‐accumulation index (Igeo), contamination factor (Cf), pollution load index (PLI), and enrichment factor (Ef). The assessment of ecological risk is studied as potential ecological risk index (RI), toxic risk index (TRI), and modified hazard quotients (mHQs). As per the Igeo and Cf, V and Cr concentrations are higher in the region. Further, PLI confirmed that 35% of samples exceeded the limits of sediment quality guidelines. The RI and TRI values show that a higher ecological risk is associated with Ni, V, and Cr and with Cu and Cr, respectively. Additionally, the 23% Ni and 20% Cu samples from mHQ indicate the severity of pollution in the aquatic environment. The inputs from anthropogenic and natural sources change the concentration of these HMs along the region. Moreover, the study of CIA and plagioclase index of alteration plots confirmed the low to intense weathering conditions. The statistical approach shows the linkage between Cr–V, Cu–Zn, and principal component analysis–derived prominent sources: industrial and agricultural runoff, as well as higher silicate weathering, contribute to the HMs concentration in the region. The Kabini River passes through different climatic and land‐use domains of Kerala and Karnataka, which eventually regulate the HM concentration and geo‐environmental processes in the region and affect the health risk to humans in one or the other way. The reference data generated from the present work are absolutely new and would be significant in the future for deriving sustainable development plans for the well‐being of human beings and precious natural resources.

Metabolic engineering-enabled dual-color biosensor for discriminative and sensitive detection of toxic lead and mercury in environmental waters

The ubiquity of toxic heavy metals, particularly lead (Pb) and mercury (Hg), in environmental waters severely threatens ecosystems and human health. We developed a metabolic engineering-based dual-color bacterial biosensor for the sensitive and discriminative detection of Pb(II) and Hg(II) at nanomolar levels. The biosensor leverages the synthetic biology approach to integrate two pigments, prodeoxyviolacein (PDV) and deoxyviolacein (DV), into a single construct that responds distinctly to Pb(II) and Hg(II), respectively. The engineered E. coli biosensor exhibits a detection range of 0.732–3000 nM for Pb(II) and 0.183–750 nM for Hg(II), with low detection limits of 0.732 nM for Pb(II) and 0.183 nM for Hg(II). The biosensor demonstrated high sensitivity, selectivity, and accuracy with a recovery rate close to 1 in freshwater and seawater matrices. Notably, the biosensor's visual readout allows for rapid, equipment-free assessment. It is a practical tool for real-world monitoring of heavy metal pollution, especially in remote or resource-limited settings. This study underscores the potential of whole-cell biosensors as a sustainable and effective alternative to traditional heavy metal detection methods.

Geochemical Modeling and Quality Assessment of the Surface Waters from the Mouhoun River System, Burkina Faso: Implications of Water–Rock Interactions and Anthropogenic Activities

Major ion and heavy metal geochemistry was used to investigate the factors that control the Mouhoun River water quality in western Burkina Faso. Major cation concentrations was in the following decreasing order: Ca2+> Na+> K+> Mg2+, reflecting silicate weathering. However, relatively high HCO3- and SO42- concentrations could be related to dissolution of calcite and sulfide minerals, respectively. The average heavy metal concentrations in the riverine system were in the following order: FeT>Ag>Mn>Zn>Pb>Cu>Ni>AsT>Cr>Hg>Co>Cd with FeT and Ag exceeding the World Health Organization permissible limits. Concentrations of all heavy metals, except Cr, were higher in the Mouhoun system compared to the average world river concentrations. Adsorption and speciation models showed that Zn, Ag, Cd, Co, Cr and Ni are likely to remain in their free ionic forms, and thus posing serious threats to aquatic life and human health. Ag-Hg-Ni-Cd association around Poura and Tenado on the principal component plot suggested that the widespread artisanal gold mining in these areas may have contributed to these metals’ loading. In contrast, NH4+, Pb, Cu, Cr, AsT and Zn were clustered around a densely populated and industrialized Kou watershed, pointing to agricultural and industrial sources of these pollutants. Furthermore, the Kou River had the highest metal index followed by Tenado, Samendeni, Poura and Boromo. Hence, the chemistry of the Mouhoun River and its tributary appears to be mainly controlled by population density and various anthropogenic activities taking place in their drainage basins. The findings could provide avenues for sound and sustainable water resource management in a water scarce semi-arid environment.

Agricultural waste-based biochars for sustainable removal of heavy metals from stabilized landfill leachate.

In this work, biochars were used as adsorbents to remove Cu, Cd, and Zn ions in a real stabilized leachate from a controlled landfill. Oak fruit shells biochar (OFSBC) and date palm fibers biochar (DPFBC) were obtained by pyrolysis of oak fruit shells and date palm fibers at 700°C and 400°C, respectively. OFSBC and DPFBC showed well-developed structures and high specific surface areas (520.16 m2/g and 470.46 m2/g, respectively). Equilibrium adsorption of heavy metal ions on DPFBC and OFSBC occurred after 4h and 2h of stirring. The removal efficiencies of Cu, Cd, and Zn ions were 97.01%, 94.40%, and 80.59% with DPFBC and 90.10%, 88.33%, and 76.16% using OFSBC, respectively. The Avrami fractional order model was appropriate for describing kinetic adsorption. Increasing the dose of adsorbent improves heavy metal ion retention. Thermodynamic tests have proven the spontaneous and endothermic adsorption of these heavy metals. The electrostatic attraction, ion exchange, complexation, metal-π bending, and surface precipitation and pore filling were regarded as the most predominant heavy metal retention mechanisms from the landfill leachate onto the biochar surface. Separately, the DPFBC showed the best performance than OFSBC regarding the improvement of leachate quality. Chemical oxygen demand (COD), biological oxygen demand (BOD5), ammoniacal nitrogen (NH3-N), and phosphorus (P) were respectively removed at an efficiency of 53.57%, 29.17%, 36.07%, and 37.5%, respectively. Thus, the results allow highlighting that the adsorption on DPFBC and OFSBC can be an effective alternative in the practice of landfill leachate treatment.

BIOACCUMULATION OF CU AND CO IN LEAFY AND FRUIT VEGETABLES FROM THE SUBURBS OF MITROVICA, KOSOVO

Contamination of vegetables with heavy metals is one of the basic environmental problems, especially in developing cities, primarily due to the uncontrolled level of pollution caused by industrial growth and the increase in the number of vehicles using petroleum fuels. This paper aims to determine the bioconcentration of heavy metals Cu and Co in leafy and fruit vegetables grown near Kosovska Mitrovica (Republic of Kosovo). Three places near Kosovska Mitrovica (Zvečan, Frashër, and Polski) are grown: parsley, spinach, lettuce, peppers, eggplant, and cucumber. All analyzed crops are from the 2023 harvest. In the same period, an analysis was made of the soil on which the crops were grown. The bioconversion factor (BF)of the selected leafy and fruit vegetables was also determined. The ICP-MS technique was used to determine the concentration of Cu and Co in soil and leafy and fruit vegetables. From the obtained analyzes it was determined that the soil in Frashër contains the highest amount of Cu and Co - 58.4 mg/kg and 11.6 mg/kg respectively. The amount of Cu in the examined dry leafy and fruit vegetables is in the range from 5.38 mg/kg to 22.4 mg/kg, and of Co from 0.27 mg/kg to 2.99 mg/kg. The bioconcentration factor of the studied leafy and fruit vegetables of Cu and Co is in the range of 0.04 to 0.26 and 0.15 to 0.65 respectively. The accumulation of Co in the analyzed vegetables is higher than the accumulation of Cu, due to the higher BF values for Co. The statistical processing of the results (t-test) showed that there is a difference in the concentration of Cu and Co between leafy and fruit vegetables, but there is no statistically significant difference because the obtained p-values are greater than the marginal p-values.

Zinc Accumulation Pattern in Native Cortaderia nitida in High Andes (Ecuador) and Potential for Zinc Phytoremediation in Soil

The aim of this work was to determine the content of heavy metals in soil and, for the first time, in wild Cortaderia nitida, and to discuss its potential as a metal phytoremediator plant. We sampled sediments (bulk and rhizosphere) and C. nitida (roots and shoots) in three nearby spots with different land uses (urban, industrialized and agricultural) along the Chibunga river basin (Ecuador). We analyzed the physico-chemical parameters in soil and heavy metal contents in soil and plants. The agricultural sediments showed the highest conductivity and redox potential, but the lowest pH. Among all the metals analyzed in soil and plants, we only found significant values of Zn and Fe. We observed clear differences in patterns of Zn distribution throughout soil and plants among the three areas sampled, thus suggesting that soil properties played an important role in Zn compartmentalization. Also, C. nitida demonstrated effective Zn translocation from roots to shoots, especially in farmlands (translocation factors between 1.64 and 2.51). Together with the results obtained for other Cortaderia species in metal-polluted areas, this study proposes C. nitida as a candidate to further study its metal phytoremediation potential and encourages this research in heavy metal-enriched soils.

ACCUMULATION OF HEAVY METALS IN APPLES AND PEARS FROM THE SUBURBS OF MITROVICA, KOSOVO

Intake of heavy metals through the food is a food safety problem that seriously affects consumer health. Therefore, information is needed on the intake of food contaminated with heavy metals and their concentrations, to assess the potential risk for human health. This paper aims to determine the accumulation of metals in apples and pears grown in the surroundings of Kosovska Mitrovica (Republic of Kosovo) and the bioconcentration factor (BF). With the help of the ICP-MS technique, were determined the amounts of Cu, Fe, Co, Mn, Ni, and Cr in apples and pears grown in three regions - Zvečan , Frashër, and Polski. From the conducted tests, the highest concentrations in apples and pears were determined for iron (on average 100.67 mg/kg for apples and 107.4 mg/kg for pears) and the lowest concentrations for cobalt (on average 0.13 mg/kg for apples and 0.18 mg/kg for pears). The lowest bioconcentration factor in apples is 0.01 (for Fe, Co, and Mn in all three regions), and the highest is 0.32 (for Cr in Zvečan). When determining the bioconcentration factor in pears, the lowest (0.01) was determined for iron (in all three regions) and manganese (in Zvečan and Frashër regions), and the highest bioconcentration factor was determined for copper – 0.46 (Polski region). There is a very high correlation between the values obtained for the analyzed metals in apples and pears. According to BF values, pears extract twice as much Cu and Co from the soil compared to apples, and the extraction of other metals from the soil is the same for both types of fruit.

Probabilistic human health risk assessment of commercially supplied jar water in Gopalganj municipal area, Bangladesh

Every day, the amount of quality fresh water decreases notably due to contamination of drinking water. As a result, people use commercially supplied jar water in the southern part of Bangladesh as well as in the Gopalganj municipal area. This study aims to investigate the physicochemical parameters, trace elements, and microbial parameters for assessing human health risks from oral ingestion of these elements. This study gathered commercially supplied jar water samples from 15 companies in the Gopalganj municipal area during the post-monsoon season. Temperature, potential of hydrogen (pH), total dissolved solids (TDS), electrical conductivity (EC), and salinity showed significant variation among the samples, and the level was within the national and international standard limits. The concentrations of iron (Fe) and arsenic (As) were measured using a UV–VIS spectrophotometer and atomic absorption spectroscopy (AAS), respectively. The microbial analysis was conducted by the membrane filtration method. The study found that the water samples had an average concentration of 0.16 mg/L in terms of Fe and 0.016 mg/L in terms of As, with the mean value of As exceeding the standard limits. On the other hand, the mean Fe concentration value did not exceed the standards. Probable human health risk from heavy metal in the jar water was determined by hazard quotient (HQ), hazard index (HI), and carcinogenic risk (CR) assessments. A child (HI = 3.5914) is more vulnerable to non-carcinogenic human health risks than an adult (HI = 1.6931). Furthermore, pollution in water samples was found to pose a high carcinogenic risk, with children (CR = 1.6 × 10−3) being more vulnerable to carcinogenic risk than adults (CR = 7.5 × 10−4). In the microbial analysis, 100% of the samples exceeded the total coliform and fecal coliform standard limits, and 80% of the samples exceeded the Escherichia coli standard limits. Among the samples, 7% present high risk, around 47% present medium risk, 26% show low risk, and 20% show no risk based on the E. coli standard limits. This study did not find any samples that exceeded the extremely high limit for E. coli concentration. This study found that drinking jar water samples had inadequate quality, which may increase the risk of water-borne infections such diarrhea as well as heart disease, diabetes, and cancer. As a result, the manufacturer of drinking water in jars must carry out the essential quality control procedures, and the government should regularly monitor the procedures.

Assessment of Heavy Metals (Cr, Cu, Pb, and Zn) Bioaccumulation and Translocation by Erigeron canadensis L. in Polluted Soil

This work aims to assess the bioavailability and bioaccumulation of Cr, Cu, Pb, and Zn in the soil–plant system (Erigeron canadensis L.) in the zone of anthropogenic impact in Dnipro city, a significant industrial and economic centre of Ukraine. Sampling was carried out at three locations at distances of 1.0 km, 5.5 km, and 12.02 km from the main emission sources associated with battery production and processing plants in Dnipro. The concentrations of heavy metals such as Cr, Cu, Pb, and Zn were analysed using atomic emission spectrometry from soil and parts of Erigeron canadensis L. The highest concentrations of elements in the soil, both for the mobile form and the total form, were determined to be 48.96 mg kg−1 and 7830.0 mg kg−1, respectively, for Pb in experimental plot 1. The general ranking of accumulation of elements in all experimental plots, both for the plant as a whole and for its parts, was as follows: Zn > Cu > Cr > Pb. Zn for plants was the most available heavy metal among all studied sites and had the highest metal content in the plant (339.58 mg kg−1), plant uptake index (PUI-506.84), bioabsorption coefficient (BAC-314.9), and bioconcentration coefficient (BCF-191.94). According to the results of the study, it is possible to evaluate Erigeron canadensis L. as a hyperaccumulator of Zn, Cu, and Cr and recommend it for phytoextraction of soils contaminated with Zn, Cu, and Cr and phytostabilization of soils contaminated with Pb.

Effects of Ageing on Surface Properties of Biochar and Bioavailability of Heavy Metals in Soil

This study aims to explore the effects of biochar ageing on its surface properties and the bioavailability of heavy metals in soil. The biochar was subjected to chemical oxidation/dry–wet cycles (CDWs), chemical oxidation/freeze–thaw cycles (CFTs), and natural ageing (NT) to analyze changes in the elemental composition, pH, specific surface area, pore volume, and surface functional groups. Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM) were applied to characterize the functional groups and microstructure, and the BCR sequential extraction method was employed to demonstrate the fractionation distribution of Cu, Cd, and Pb. The results showed that the CDWs and CFTs treatments significantly reduced the carbon content of the biochar (with a maximum reduction to 47.70%), increased the oxygen content (up to 49.17%), and notably increased the specific surface area and pore volume. The pH decreased significantly from 9.91 to 4.92 and 4.99 for the CDWs and the CFTs, respectively. The FTIR analysis indicated notable changes in hydroxyl and carboxyl functional groups, and the SEM revealed severe microstructural damage in biochar after the CDWs and CFTs treatments. The heavy metal fractionation analysis indicated that exchangeable Cu, Cd, and Pb significantly increased after the CDWs treatment, reaching 31.40%, 5.25%, and 6.79%, respectively. In conclusion, biochar ageing significantly affects its physicochemical properties and increases the bioavailability of heavy metals, raising concerns about its long-term remediation effectiveness.

The Utilization of Carbonated Steel Slag as a Supplementary Cementitious Material in Cement.

Carbon emission reduction and steel slag (SS) treatment are challenges in the steel industry. The accelerated carbonation of SS and carbonated steel slag (CSS) as a supplementary cementitious material (SCM) in cement can achieve both large-scale utilization of SS and CO2 emission reduction, which is conducive to low-carbon sustainable development. This paper presents the utilization status of CSS. The accelerated carbonation route and its effects on the properties of CSS are described. The carbonation reaction of SS leads to a decrease in the average density, an increase in the specific surface area, a refinement of the pore structure, and the precipitation of different forms of calcium carbonate on the CSS surface. Carbonation can increase the specific surface area of CSS by about 24-80%. The literature review revealed that the CO2 uptake of CSS is 2-27 g/100 g SS. The effects of using CSS as an SCM in cement on the mechanical properties, workability, volume stability, durability, environmental performance, hydration kinetics, and microstructure of the materials are also analyzed and evaluated. Under certain conditions, CSS has a positive effect on cement hydration, which can improve the mechanical properties, workability, bulk stability, and sulfate resistance of SS cement mortar. Meanwhile, SS carbonation inhibits the leaching of heavy metal ions from the solid matrix. The application of CSS mainly focuses on material strength, with less attention being given to durability and environmental performance. The challenges and prospects for the large-scale utilization of CSS in the cement and concrete industry are described.

The human health risks assessment posed by the presence of heavy metals in the rice varieties available in the Neyshabur market.

The present study was designed to determine the levels of heavy metals (Cu, Pb, Ni, Cr, Zn, Mn, Cd, and Co), Mn, and As in Iranian-grown rice and imported rice consumed in Neyshabur City. For this research, 90 samples from 30 different brands widely consumed in this city were collected. The content of heavy metals and the health risks associated with their use were then studied. The study found that Zn (14.21mgkg-1) had the highest content in Iranian and imported rice varieties, whereas Cd (0.02mgkg-1) had the lowest value. The health risk assessment was also done in three scenarios and separately for two types of rice. The results showed that the total hazard quotient (i.e., THQ) was measured for all metals and all three scenarios, and for both types of rice, it is THQ > 1, which indicates the risk of non-carcinogenic in rice. The cancer risk for three scenarios and two types of imported andIranian rice is in the unsafe range for As (8.80× 10-4 to 7.00× 10-3),Ni (4.60 × 10-4 to 3.60 × 10-3) and Cr (2.20 × 10-4 to 1.90 × 10-3) and negligible for Pb (1.09 × 10-6 to 1.49 × 10-5) and Cd (7.83 × 10-6 to 8.20 × 10-5).

Effective remediation of mercury (II) from aqueous solutions using CS-MnFe2O4-CoS-MWCNTs: Box-Behnken design optimization and adsorption isotherm, kinetics, and thermodynamics evaluation.

Mercury (Hg) is a hazardous heavy metal, non-biodegradable and toxic, posing a serious threat to aquatic life and human health. Therefore, the removal of Hg ions from contaminated water using effective and eco-friendly adsorbents is necessary. In the present study, three magnetic chitosan-based organic-inorganic nanocomposites, such as CS-MnFe2O4, CS-MnFe2O4-CoS, and CS-MnFe2O4-CoS-MWCNTs, were designed and constructed to investigate their capacity for adsorbing Hg ions from aqueous solutions. The physicochemical properties of prepared composites were characterized by various analyses. The BET analyses indicated their high surface area and porous structure, and the N2 adsorption-desorption showed that the modification of CS in three stages by MnFe2O4 and crosslinking reaction, CoS preparation, and MWCNT incorporation resulted in increased N2 adsorption. The XRD confirms the synthesis of MnFe2O4 and CoS in the CS matrix and also the distinct peaks of MWCNTs. The CS-MnFe2O4-CoS-MWCNTs showed acceptable thermal stability with 45% char yields and superparamagnetic properties with magnetic saturation (Ms) of 16 emu g-1. The interactive impacts of independent variables (pH, contact time, and adsorbent dosage) on the removal percentage of Hg(II) onto three prepared adsorbents, as well as the process optimization, were assessed by the Box-Behnken design. The optimum conditions were identified, and the data from the analysis of variance showed that the three independent factors (pH, contact time, and adsorbent dosage) significantly influenced the adsorption of Hg(II). The adsorption isotherm and thermodynamics analysis investigation showed that at low concentrations of Hg(II), the adsorption process was both endothermic and spontaneous for the studied adsorbents.

Retraction Note: The modulatory potential of herbal antioxidants against oxidative stress and heavy metal pollution: plants against environmental oxidative stress.

Retraction Note: The modulatory potential of herbal antioxidants against oxidative stress and heavy metal pollution: plants against environmental oxidative stress.

Contamination of Arsenic Speciation in Rice

Rice is the staple food of people in Asian countries, especially in Laos, where it is carbohydrate stuff that plays an essential role as a source of energy to support human beings. Arsenic (As) is a heavy metal of which naturally occurring; it can be found in soil, rocks, and natural water sources; and is caused by human activities such as mining activities, the use of agro-chemicals (pesticides, herbicides, etc.) in agriculture. Therefore, it is possible to deposit and contaminate the environment such as the paddy soil and the irrigation; afterward, it can initiate the arsenic residues in the agricultural productions that harvesting from the contaminated area, which is the rice grain. Furthermore, the arsenic residue can give rise to a health impact on those who consume the toxic rice. According to the analysis results of arsenic contamination in the 3 types of rice samples revealed that: in the HSV sample, the total amount of arsenic was 0.11 mg/kg, and the total inorganic arsenic (iAs) was 0.09 mg/kg which included the amount of inorganic arsenic AsV was 0.02 mg/kg, the inorganic arsenic AsIII was 0.07 mg/kg; the total arsenic in the TDK8 sample was 0.19 mg/kg, the (iAs) was 0.01 mg/kg, and the amount of arsenic AsV was 0.01 mg/kg, the amount of arsenic AsIII was 0.08 mg/kg; the total arsenic in the Composite rice was 0.14 mg/kg, the (iAs) was 0.08 mg/kg, the AsV and AsIII were 0.006 mg/kg and 0.08 mg/kg, respectively. In conclusion, the arsenic residue was contaminated in all three rice samples, but the residue of total arsenic and inorganic arsenic (iAs) did not exceed the maximum permissible limit of the international standard or CODEX which is 0.3 and 0.2 mg/kg, respectively.

Characterization of Sinorhizobium strains isolated from arid and semi-arid areas of Morocco promoting the growth of Vachellia gummifera

Vachellia gummifera is a nitrogen-fixing shrub endemic to Morocco, and represents a suitable candidate for reforestation programs in dry areas. In this study, we identified seven root microsymbionts of V. gummifera, and determined their phenotypic characteristics, Plant Growth-Promoting (PGP) activities and their symbiotic efficiency. The bacteria were isolated from root nodules of the plant grown in Moroccan forest soils located in arid and semi-arid regions. The 16S rRNA gene sequences analysis of seven isolates showed similarity values ranging from 99.85% to 99.92% with Sinorhizobium fredii USDA205T. The phenotypic analyses displayed that the strains use different carbohydrates, mainly mono and di-saccharides, as a sole carbon source, and 13 out of 15 amino acids tested as the sole nitrogen source. The strains have variable tolerance to heavy metals, but are sensitive to salinity and high temperature, as no one grew in the presence of 2% NaCl (w/v) or at 40 °C, respectively. On the other hand, the strains grew in a very high osmotic stress environment induced by PEG 6000 (20% w/v), and they all grow in a pH range between 6.5 and 9. The strains possess PGP activities, such as phosphate solubilization, siderophore, and indole acetic acid production. Inoculation under axenic conditions showed that the strains increased the aerial biomass of inoculated plants up to 217%, whereas the relative symbiotic efficiency percentages (74.87–140,3%) showed that most strains are very efficient. From all these results we concluded that our strains may be proposed as inoculum for large-scale applications, such as reforestation programs.