Heat Transfer Considerations Research Articles

Simulation of fluid flow with Cuprophan and AN69ST membranes in the dialyzer during hemodialysis.

Hemodialysis is a crucial procedure for removing toxins and waste from the body when kidneys fail to perform this function effectively. This study addresses the need to improve the efficiency and biocompatibility of membranes used in dialyzers. We simulate fluid flow through two types of membranes, Cuprophan (cellulosic) and AN69ST (synthetic), to understand the complex mechanisms involved and quantify key variables such as pressure, concentration, and flow. This study presents a detailed model that applies mass conservation equations and Navier-Stokes principles adapted for porous media, along with heat and mass transfer considerations. The results revealed significant differences in the flow behavior and filtration efficiency between the two membranes, highlighting the superiority of the AN69ST membrane in terms of flow rate and toxin removal. This model serves as a valuable tool for characterizing new porous membranes in dialysis applications, enabling the prediction of the temperature, pressure, and concentration profiles. By providing this information without requiring extensive experimentation, the model complements the design and evaluation of new membranes and, optimizes their development. The ability to predict these profiles is crucial because they directly influence the parameters that determine treatment effectiveness. Moreover, this study underscores the importance of continued innovation in membrane materials and designs, contributing to improved clinical outcomes and treatment efficiency, representing a significant advancement in healthcare.&#xD.

Utilizing Distribution of Relaxation Times Analysis for Water Content Management in Anion Exchange Membrane Fuel Cells

Amid escalating concerns over air pollution and energy scarcity, Anion Exchange Membrane Fuel Cells (AEMFCs) are increasingly recognized as a viable solution for power generation, offering high efficiency, and zero emissions. Water plays a critical role within these systems as a reactant, consumed at the cathode and generated at the anode. This process can lead to disparities in water content, potentially compromising the cell's performance. Therefore, it is imperative to maintain optimal water distribution to facilitate effective charge transport and enhance electrochemical reaction kinetics. Consequently, devising a robust water management strategy is essential to ensuring the sustained operation and longevity of AEMFCs.Characterizing the water conditions at the anode and cathode under various operational states (normal, drying, or flooding) is a pivotal step underpinning effective water management strategies. Electrochemical Impedance Spectroscopy (EIS) provides a valuable tool for examining various resistances associated with kinetics, mass transport, and ohmic losses across different operational timescales, thereby facilitating a detailed assessment of water transport dynamics. Traditional analyses of EIS data often depend on equivalent circuit models, which require predefined assumptions and the selection of initial components. However, this study adopted the Distribution of Relaxation Times (DRT) methodology for its exceptional capability to disaggregate components, enabling a more nuanced analysis of the polarization processes. The DRT methodology was applied to scrutinize the patterns of loss and variation within each polarization process under varying water flooding and drying conditions at the anode and cathode. Moreover, to deepen our comprehension of how water content influences mass transport and electrochemical reaction kinetics, a three-dimensional multi-physics model for AEMFCs was developed. This model comprehensively integrates considerations of water phase transitions, heat and mass transfer, as well as the transport of liquid and dissolved water, alongside electrochemical reactions. These efforts collectively forge a comprehensive and systematic framework to advance the application of the distribution of relaxation times in optimizing fuel cell performance.

Benzopyrene content in soil and atmosphere near boiler house

The paper considers a boiler house using firewood as fuel. The amount of combustion products and harmful substances such as nitrogen oxides, soot, carbon monoxide, suspended solids and benzopyrene formed during the combustion of 13 tons of birch wood per year is determined for it. Particular attention is paid to the content of benzopyrene as a substance capable of migrating from the atmosphere into water bodies, soil and belonging to the first hazard class, thereby affecting the quality of plant products, animal feed and human health. Being a strong carcinogen, benzopyrene affects the immune system, development processes, is capable of causing mutations and being transmitted to subsequent generations. Based on software, long-term average concentrations of benzopyrene in the air in the ground layer at a height of 2 m from the surface at eight points on the ground near the emission source and at the boundary of the corresponding sanitary protection for the boiler house under consideration were calculated. It was found that for this emission source, no excess of the content of this substance in the atmosphere is observed, and the influence of the wind rose on its dispersion is shown. Using laboratory studies of the soil near the source, it was found that the concentration of benzopyrene during its accumulation over 7 years on lands intended for agricultural use does not exceed the permissible values. Also, in the work, based on the law of conservation of energy and consideration of heat transfer from combustion products through a cylindrical wall into the surrounding space during transverse flow around the pipe, expressions are written that allow determining the temperature of the outgoing flue gases taking into account their thermophysical properties, pipe material and climatic features of the area.

Two-phase magnetohydrodynamic blood flow through curved porous artery

Blood arteries are important part of our cardiovascular system. A comprehensive study of shape and anatomy of blood arteries allows to elucidate the dynamics of blood flow in these arteries. Typically, the arteries are a curved-tube like structure, with arterial walls exhibiting a composition of various porous layers. The current study embarks on a theoretical exploration of a two-fluid model of blood flow and heat transfer through the curved artery under an influence of a magnetic field. The artery walls are composed of Brinkman and Darcy layers. The blood flows through a curved artery exerts centrifugal forces on the arterial walls that leads to change the blood flow patterns. The significant effects of curvature along with the intensity of an applied magnetic field on the blood flow patterns, heat transfer, and resistance impedance in curved artery have been investigated in the present work. The mathematical model of the proposed work is tackled by the homotopy analysis method using physically relevant boundary and interface conditions. The significant outcome of the present work is that the heat transfer rate increases with the increase in the curvature parameter, and it reduces on raising the couple stress parameter and Hartmann number. The novelty of this work lies in the consideration blood flow and heat transfer in inner endothelial layers of curved porous artery. The result presented in this work is vital to assess the condition of atherosclerosis, aneurysms, vasculties, blood clot, etc.; beyond this, the present model can be extended for medical diagnostics, treatment planning, medical device design, drug delivery optimization, and biomedical engineering research. This study can ultimately contribute for improved patient care and outcomes in cardiovascular medicine.

Numerical study of the particle-scale heat transfer in the HTR-PM pebble bed based on GPU-DEM

An essential aspect of the design of a pebble bed high-temperature gas-cooled reactor (HTGR) is the consideration of heat transfer. A particle-scale heat transfer model was developed based on the previous GPU-DEM numerical model. This model includes the heat conduction of the particles in contact, the radiative heat transfer among particles, and unidirectional convection heat transfer in the flow field. The comparison of the predicted results with the results of the TF-PBEC experiment demonstrates the accuracy of the conduction and radiation modules within the current model. Based on the current model and the porous media model, a numerical study of the natural convection heat transfer in the High-Temperature gas-cooled Reactor-Pebble-bed Module (HTR-PM) after reactor shutdown is performed. This paper systematically introduces the model design, pebble bed generation, flow field calculation, and heat transfer simulation. The results indicate that natural convection contributes to removing residual heat in the reactor core, and a higher pressure leads to better convection heat transfer. At extremely low Reynolds numbers (Re < 10), convection heat transfer is comparable to conduction and radiation, while for pressurized pebble beds (Re = 50–500), convection heat transfer dominates. Furthermore, the influence of different models used to calculate the Nusselt number of the results is compared and analyzed. For most cases, the differences in the temperature distribution of the pebble bed obtained from the different correlations are minor. However, the impact of porosity on the local Nusselt number cannot be ignored in the extremely low Reynolds numbers flows. Overall, the particle-scale heat transfer model can provide more effective reference information for the design and construction of an HTGR.

Thermal design of a non-isothermal microfluidic channel for measuring thermophoresis

Thermophoresis describes mass transport in a non-isothermal temperature field and thus provides a fundamental understanding of the behavior of colloidal particles. Various methods have been proposed for measuring the Soret coefficient, a representative value of thermophoresis. In particular, microscopic channels are an emerging method as they shorten the equilibrium time and allow direct observation of the particles. However, little emphasis has been placed on the simultaneous consideration of fluid dynamics, heat transfer, and mass transfer characteristics within the microfluidic channel, despite the simultaneous presence of natural convection and thermodiffusion phenomena. In this study, we present a novel approach to address this gap by introducing a figure of merit, which incorporates essential parameters to accurately characterize a specific cell configuration. This figure of merit allows for the identification of a reliable measurement range in a microfluidic channel with a temperature gradient, while accounting for fluid dynamics, heat transfer, and mass transfer characteristics. The proposed approach is validated through rigorous simulations and experiments, enabling an evaluation of the impact of figure of merit-derived parameters on the measurement channel. The findings from our study demonstrate that the figure of merit serves as a representative measure for stable thermophoretic measurements in a microfluidic channel. Moreover, we propose a threshold value that signifies the transition from a diffusion-dominant to a convection-dominant field.

Morphological changes and color development during cookie baking-Kinetic, heat, and mass transfer considerations.

Color and shape are important quality attributes in baked goods, particularly cookies. Composition and processing conditions determine and influence color development and morphological changes in these baked goods. The objective of this study was to systematically evaluate the evolution of color and shape during baking to determine useful correlations that can be implemented during the assessment and modeling of the baking process. Cookies (AACC-I standard protocol 10-53.01) were baked at 185, 205, and 225°C. Moisture content, water activity, surface temperature, characteristic dimensions (radius and thickness), and color indexes (lightness, redness, blueness, and browning index [BI]) were monitored at different locations on the cookie surface and baking times. Relationships among the tested conditions were explored using correlation analysis. The cookies' dimensions and color indexes were strongly correlated with changes in moisture content over time, and those relationships were characterized using empirical models. The temperature dependence of the kinetic parameters of the changes in lightness and BI was also described and deemed independent of the location on the cookie surface. This study provides insights into the influence of heat and mass transfer on the physical and physicochemical changes of cookies during baking. The kinetic and secondary models developed in this study can serve as important components for establishing a comprehensive approach for coupling heat transfer, mass transfer, and reaction kinetics to estimate and optimize cookie-baking processes. PRACTICAL APPLICATION: The findings from this study provide valuable information for better understanding the morphological changes and color developments during the cookie-baking process. The quantitative data and models generated in this study will allow identifying baking conditions for better quality development.

Large-scale PANDA facility – radiation experiments and CFD calculations

Abstract CFD modelling of the thermo-hydraulic phenomena in the containment during the various phases of a severe accident necessarily requires consideration of radiative heat transfer – in the presence of steam. These radiative phenomena include (i) energy transfer within the gas mixture and (ii) between the gas and surrounding structures. Preliminary calculations carried out for these types of experiments within the OECD/NEA HYMERES-2 project with the CFD code containmentFOAM using a Monte Carlo solver for thermal radiation, demonstrated that the radiative heat transfer is significant even for very small amounts of vapour in the range of ≈0.1 % to ≈2 %. For this reason, the test matrix was tailored to the two opposite extremes: either gas compositions with a low vapour/steam content, where radiative heat transfer can be neglected, or gas mixtures with higher vapour contents, so that radiative heat transfer plays a dominant role. For the selected experiments of the H2P2 series and the corresponding CFD calculations, a vessel with a diameter of 4 m and a height of 8 m was preconditioned with different air-vapour mixtures (a) at room temperature and (b) elevated temperatures. A stable helium layer was then built-up in the upper part of the vessel. The gas was then compressed by injecting helium from above which resembles with best efforts a compression with a piston in a cylinder. This results in a height-dependent and transient increase of the gas temperature. These experiments and the associated CFD calculations were developed to isolate the phenomena of thermal radiation as good as possible from convective and diffusive effects – within the always present experimental limitations. For the reference experiment with ‘dry conditions’ corresponding to the lowest experimentally possible humidity of ≈0.1 %, we show that the use of a model without radiation provides the best agreement between the experimental and numerical results. For the much higher steam content of ≈60 %, the statistical narrow band correlated-k model (SNBCK), non-gray gas model, is the best candidate for future calculations – with computationally forgivable additional effort. We also provide with the Filtered Rayleigh Scattering technique (FRS) an outlook for a possible future instrumentation approach to better meet the requirements of the CFD community.

6-Stroke water injection engine literature review with an introduction of heat transfer and thermodynamic analysis

AbstractInternal combustion engines have played a crucial role in the advancement of society. Consequently, there has been a persistent need to enhance their efficiency and performance. The water-injected six-stroke engine is based on conventional four-stroke engines, producing additional power by injecting water into the hot combustion products during the expansion stroke, thereby increasing the overall engine efficiency. However, a comprehensive review that consolidates existing knowledge and identifies future research opportunities in six-stroke engine technology is lacking. This study addresses this gap by thoroughly examining the thermodynamic operation of six-stroke engines and analyzing the impact of water injection on engine performance. The review covers literature from 1994 to 2023, categorizing studies based on the modeling approach, working fluid, thermodynamic cycle, and consideration of heat transfer. Among the 18 analyzed articles, predominantly published from 2015 to 2019, half utilize analytical models, while the rest employ experimental models addressing heat transfer losses. Notably, water injection exhibits a substantial influence, manifesting as a 5.18% increase in brake power and a 1.55% enhancement in thermal efficiency, particularly with acetylene as the working fluid. Finally, a literature overview of water injection in hot gas environments within the engine cylinder was conducted in addition to a preliminary thermodynamic analysis of the Otto and Diesel cycles to compare different configurations outlined in the literature. The lack of studies, experimental setups, and non-idealized models that consider factors such as heat transfer or water evaporation during injection is evident. By critically synthesizing the available literature, this study offers valuable insights into the potential advantages, limitations, and prospects of six-stroke engine studies.

Effect of aspect ratio on mechanical anisotropy of lattice structures

Triply periodic minimal surface (TPMS) lattice structures with controllable mechanical properties and porous architecture are promising candidates for lightweight and energy-absorbing applications. In parametric structural design, the research on structural geometric characteristics, such as aspect ratio (R) and surface curvature, has mainly focused on fluid and heat transfer considerations. However, their impact on multi-directional mechanical properties has yet to be thoroughly investigated. This study, combining representative volume elements (RVE) based on periodic boundary conditions and theoretical surface morphological characteristics, investigates the mechanical properties and deformation behavior of lattice structures with different aspect ratios in multiple directions. The results indicate that the aspect ratio highly influences the deformation behavior of the lattice structure in different directions. The local curvature and force state of the lattice structure can be adjusted by aspect ratio to reduce local stresses and deformations in different loading directions. Compared with the simulation results of representative volume elements, the structural stress concentration and failure position can be predicted by the Gaussian curvature distribution. In addition, the elastic modulus of the structures in the [100] and [001] directions can also be adjusted by aspect ratio. Through experimental verification in the [001] direction, the structure with an aspect ratio of 2 can greatly enhance the elastic modulus (121%∼440%), maximum stress (10%∼183%), and energy absorption (33%∼85%). The significance of this work is to improve the understanding of the influence of geometric features on the mechanical properties and deformation behavior of lattice structures, which provides a new design approach for triply periodic minimal surface lattice structures in applications of impact protection and bone scaffold.

Three-dimensional analysis of thermoelastic damping in couple stress-based rectangular plates with nonlocal dual-phase-lag heat conduction

Since thermoelastic damping (TED) plays a decisive role in the functioning of micro/nanoresonators, accurate assessment of its magnitude in these tiny systems is imperative. Successfully simulating the thermomechanical behavior of various mechanical elements requires consideration of heat transfer in all three principal directions. Furthermore, there is no denying the impact of size on the mechanical and thermal domains. In light of these reasons, the current study strives to create a three-dimensional (3D) size-dependent TED model for rectangular micro/nanoplates via the use of the modified couple stress theory (MCST) and nonlocal dual-phase-lag (NDPL) heat transfer model concurrently for the first time. To accomplish this, by applying the Galerkin method to the 3D NDPL-based heat equation, the relation of temperature field is derived. Moreover, the coupled thermoelastic constitutive relations are extracted by including the couple stress effect. Lastly, by exploiting the obtained relations in the energy dissipation approach, an analytical TED formula in the form of infinite trigonometric series is attained. To appraise the rightness of derived formulation, the method of model reduction is applied. Moreover, an elaborate convergence analysis is implemented to realize the number of sufficient terms of the provided solution that result in well-grounded outcomes. A rigorous simulation study is also accomplished on the role of 3D heat conduction, scale parameters of MCST and NDPL model, boundary constraints, geometry and material in the variations of TED. Findings imply the definite impact of heat conduction dimension on TED value in rectangular plates with a large ratio of thickness to length and width.

A Consideration of Heat Transfer between the Head and the Media in HAMR

A Consideration of Heat Transfer between the Head and the Media in HAMR

Thermomechanical modeling of the shearing process during fine blanking of quenched and tempered steel

In order to develop an alloy design for fine blanking of deformation mechanism-based sheet metal materials such as high manganese steel, knowledge of the temperature during the shearing process is required. Thermomechanical modeling of shear zone temperature requires consideration of contact heat transfer, which depends on stress state as well as temperature. This paper deals with a methodology for calibrating the contact heat transfer coefficient during fine blanking using indirect temperature measurements. For this purpose, a thermomechanically coupled finite element (FE) model was designed considering thermoviscoplasticity, temperature-dependent physical and thermophysical parameters as well as a steady-state calibrated contact heat transfer coefficient. Experimental fine blanking tests were carried out to validate the model using force, die roll and thermography measurements based on varied blanking velocities. The thermomechanically coupled FE modeling showed a sufficiently accurate correspondence regarding the experimentally determined blanking force, die roll as well as sheared surface temperature. Thermographically determined sheared surface temperatures allowed calibration of locally different contact heat transfer coefficients as a simplified approach under steady-state conditions.

Review on nanofluid preparation, stability analysis, and heat enhancement by nanofluids in pipe with passive elements

Heat enhancement applications such as heat exchangers, heating, ventilation, and air-conditioning systems, nuclear and chemical plants, etc., help to increase the thermal rating and performance of the system in addition to decreasing the cost, and size of the system. The heat exchanger design is very complex compared to other designing procedures, which requires proper heat transfer value and consideration of pressure drop, performance of the system, reliability, and durability of the system. The major drawback of the conventional fluid is its low thermal conductivity, which creates a negative impact on heat transfer, the nanofluids need to overcome this limitation. This paper reviews the preparation of nanofluid, stability analysis of nanoparticles, typical nanoparticles, and base fluids in heat transfer augmentation. Passive element heat enhancement techniques like twisted tapes showed positive results in laminar flow compared to turbulent flow, and ribs on the geometry, conical nozzles, and rings are better for turbulent flows than laminar flows. This article highlighted the main gaps and challenges for future research.

Water/ice mixture- and freezing-front motion in a non-isothermal liquid bridge

We experimentally investigate the water/ice mixture- and freezing-front behavior in a water liquid bridge under isothermal and non-isothermal conditions. We find rapid propagation, temporary suspension, and regression of the water/ice mixture front, and finally, it merges with the freezing front when part of the liquid bridge is higher than the freezing temperature. However, freezing-front propagation follows dendritic ice formation, and a protrusion forms at the middle of the liquid bridge as long as the whole liquid bridge is lower than the freezing temperature. We explain those phenomena by quasi-stationary heat-transfer considerations.

Numerical modelling for design of microchannel reactors: Application to hydrogen production from methanol by steam reforming

Microchannel reactors involve chemical-reaction engineering problems in their design and operation, with heat and mass transfer considerations dominating their practicability and efficiency. Study of the fundamental transport phenomena necessitates their description in sophisticated mathematical form. The present study seeks to address this particular problem by investigating the effects of various factors on the transport processes in a heterogeneously catalysed microchannel steam reforming reactor. Numerical modelling for reactor design was performed using a model that accounted for complex catalyst dynamics. Dimensionless number analyses were conducted to understand the nature of the transport processes. The reactor performance was evaluated by means of various parameters, and design recommendations were made. Different operating limit lines were mapped out, and various definitions of energy efficiency were distinguished. The results indicated that the use of microchannel technology enables the achievement of unusually favourable conversion. While mass-transfer limitations are dominant, the reaction is practically feasible at millisecond contact times. A maximum output power in excess of 70 watts per channel can be reached, and energy efficiencies up to about 70 percent are available. The operating limit line can be changed as desirable to maintain the desired product yield throughout the range of conditions. While an optimum velocity for maximum efficiency exists, the flow rate and catalyst loading must be carefully adjusted to simultaneously control the conversion and maximum power within certain needed limits.

Explicit–implicit schemes for non-isothermal filtration problem: Single-temperature model

In this paper, we consider a non-isothermal filtration model for a two-phase immiscible incompressible fluid, for the numerical implementation of which an explicit–implicit algorithm is proposed. The problem is presented in a mixed generalized formulation, and an explicit–implicit method of the IMPES type is used to calculate the pressure, full velocity and water saturation, and an explicit–implicit scheme is built to calculate the temperature and heat flux with explicit consideration of convective heat transfer. At the beginning of the article, the mechanism of temperature homogenization of according to temperature heterogeneous system is considered. In computational experiments, special attention is paid to the comparison of the non-isothermal model with the isothermal one, including the discussion of fingering instability.

Exploring Propagating Soliton Solutions for the Fractional Kudryashov–Sinelshchikov Equation in a Mixture of Liquid–Gas Bubbles under the Consideration of Heat Transfer and Viscosity

In this research work, we investigate the complex structure of soliton in the Fractional Kudryashov–Sinelshchikov Equation (FKSE) using conformable fractional derivatives. Our study involves the development of soliton solutions using the modified Extended Direct Algebraic Method (mEDAM). This approach involves a key variable transformation, which successfully transforms the model into a Nonlinear Ordinary Differential Equation (NODE). Following that, by using a series form solution, the NODE is turned into a system of algebraic equations, allowing us to construct soliton solutions methodically. The FKSE is the governing equation, allowing for heat transmission and viscosity effects while capturing the behaviour of pressure waves in liquid–gas bubble mixtures. The solutions we discover include generalised trigonometric, hyperbolic, and rational functions with kinks, singular kinks, multi-kinks, lumps, shocks, and periodic waves. We depict two-dimensional, three-dimensional, and contour graphs to aid comprehension. These newly created soliton solutions have far-reaching ramifications not just in mathematical physics, but also in a wide range of subjects such as optical fibre research, plasma physics, and a variety of applied sciences.

Theoretical and experimental validation of critical thermal properties of advanced vacuum bagging for composite manufacturing

The vacuum bagging is a common but critical step of various manufacturing process chains for Carbon/Glass Fibre reinforced polymers (C/GFRP). Whilst developing a new generation of vacuum bagging, significant efforts have been made to deeply understand the relevant physics fields, process variables involved and to provide predictive approaches to support dimensioning and scaling exercises prior to implementation into real production process. Main features of the new bagging system are, (1) the reduction of material diversity through merging of various properties within one single layer and, (2) the suppression of critical folding steps by using thermoforming for pre-shaping purposes. This paper will mainly focus on considerations of heat transfer during the pre-shaping of the film, directly on the CFRP part short before the curing step. For the better risk assessment of the short time exposition of an uncured composite part to the heat flow, a problem of transient coupled field analysis involving heat transfer via conduction, convection and radiation is formulated and solved by using Finite Element Analysis in COMSOL under consideration of realistic process conditions. Further a section dedicated to the comparison of the obtained results with measurements performed on a system including an IR-emitter, the bagging material, a ground plate and in some studies as well a CFRP sample is included. During the study the influence of time, power output of the emitter, distance between emitter and surface as well as irradiation angle has been assessed including a comparison of simulated results and performed measurements.

A comparative analysis of integrating thermochemical oxygen pumping in water-splitting redox cycles for hydrogen production

Solar thermochemical hydrogen (STCH) is a promising route for renewable fuel production, but efficiency and cost concerns must be addressed before it can contribute meaningfully to decarbonization efforts. The oxygen removal (reduction) step of two-step STCH redox cycles needs high temperature (1300–1500 °C) and low oxygen partial pressure (10-5-10-3 bar). This consumes significant energy by way of redox reheating, re-radiation losses and pumping work. Thermochemical oxygen pumping (TcOP) has been shown to be more efficient than mechanical pumps in the medium vacuum range, enabling higher heat-to-fuel efficiency and potentially lower reduction temperatures. We have previously proposed a novel Reactor Train System for STCH and reported significant efficiency and productivity improvements by replacing mechanical pumps with TcOP. The current work is a comparative analysis of different implementations of TcOP and its hybridization with conventional oxygen removal schemes like mechanical vacuum pumps and inert gas sweep. The integration of these hybrid TcOP systems with different STCH reactor systems using redox monoliths or particles is analyzed in terms of energy use along with mass and heat transfer considerations. Our results show that direct oxygen transfer between STCH and TcOP reactors results in the best performance for reduction oxygen partial pressures below 10 Pa. Furthermore, we show that achieving reduction pressures of 1 Pa and lower is challenging with existing reactor systems due to a combination of low gas density and relatively high molar flowrates. This challenge also applies to other oxygen removal systems like vacuum pumps and inert sweep.