Fundamental Mode Research Articles

Principle of contrast-enhanced ultrasonography.

Sonazoid, an ultrasound contrast agent, has been covered by insurance in Japan since January 2007 for the diagnosis of hepatic mass lesions and is widely used for diagnosing not only primary liver cancer but also liver metastases such as those from breast cancer and colorectal cancer. Contrast-enhanced ultrasound for breast mass lesions has been covered by insurance since August 2012 after phase II and phase III clinical trials showed that the diagnostic performance was significantly superior to that of B-mode and contrast-enhanced magnetic resonance imaging. This paper describes the principles of imaging techniques in contrast-enhanced ultrasonography including the filter, pulse inversion, amplitude modulation, and amplitude-modulated pulse inversion methods. The pulse inversion method, which visualizes the second-harmonic component using the nonlinear scattering characteristics of the contrast agent, is widely used regardless of the contrast agent and target organ because of its high resolution. Sonazoid has a stiffer shell and requires a higher acoustic amplitude than Sonovue to generate nonlinear vibrations. The higher transmitted sound pressure generates more tissue harmonic components. Since pulse inversion allows visualization of the tissue harmonic components, amplitude modulation and amplitude-modulated pulse inversion, which include few tissue harmonic components, are primarily used. Amplitude modulation methods detect nonlinear signals from the contrast agent in the fundamental band. The mechanism of the amplitude modulation is considered to be changes in the echo signal's phase depending on the sound pressure. Since the tissue-derived component is minor in amplitude modulation methods, good contrast sensitivity can be obtained.

Frequency-Tunable SIW Band-Reject Filter with Increased Fundamental Mode Bandwidth for Spectrum Underlay Cognitive Radio

This paper presents the design of a frequency-tunable substrate-integrated waveguide (SIW) band-reject filter, specifically for spectrum underlay cognitive radio operation. The proposed filter has a simple tuning circuit but provides a wide frequency tuning range from 2.9 to 4.4 GHz (41%). The second resonant mode has been suppressed using a simple quadrature coupling; hence, the fundamental mode bandwidth of the filter has been increased from 2.08 GHz to 3.36 GHz. Due to its wide tuning range, simple tuning circuit, and increased fundamental mode bandwidth, the proposed filter is greatly important in underlay cognitive radio construction. The second-order filter has also been developed, and its performance is analyzed with both simulation and measurement. It gives a tunable bandwidth of 41%, an insertion loss of more than 10 dB, and a fundamental mode bandwidth of 3.36 GHz. The filter performance is also analyzed after connecting it to the standard horn antenna. Finally, from the total efficiency plots, it has been concluded that the proposed filter achieves all the above advantages with a low-lossy nature.

Analytical Study of Damped Standing Longitudinal MHD Waves in Flowing Coronal Loops: The Effect of Thermal Conduction

The longitudinal magnetohydrodynamic (MHD) oscillations of coronal loops have been investigated in dissipative flowing loops. Thermal conduction has been considered as the damping mechanism of the wave. We aim to construct the damped longitudinal waves by superposing two propagating waves that propagate in opposite directions. The two propagating components must have the same oscillation frequencies and damping rates, which has been described impossible by some authors, but we have used a technique to overcome this difficulty. The equations of motion are combined to obtain a differential equation for the velocity perturbation. Using the weak damping condition, the perturbation method is used to solve the dispersion relation. In the leading order approximation, the oscillation frequency of the standing waves is determined. In the first-order approximation, we let both the oscillation frequency and wavelength of the propagating waves be perturbed due to the presence of thermal conduction, which enables us to determine the damping rate of the standing waves. Our results show that the plasma flow is an essential parameter in determining the effectiveness of the damping mechanism. Also, the exact solutions of the dispersion relation have been determined without using weak damping assumption. Interestingly the two solutions are the same. Introducing plasma flow to the coronal loop causes the period ratio of the fundamental mode to the first overtone to decrease more.

Bulged CH3NH3PbBr3 Microwires for Single‐Mode Lasing

Herein, the lasing action of fabricated bulged CH3NH3PbBr3 microwires is demonstrated with features of a low threshold, narrow linewidth, single‐mode operation, and high intensity. Benefiting from the bulged end facets, the CH3NH3PbBr3 microwires are feasible for constructing a high‐brightness, whispering‐gallery‐mode(WGM)‐type, and single‐mode laser while suppressing Fabry–Pérot‐type multi‐mode lasing. Numerical simulation unveils that the bulged end facets result in the significantly reduced reflectivity of fundamental waveguided modes. The obtained microlasers require neither complex structures (such as distributed Bragg reflector) nor careful pumping adjustment, suggesting the practical feasibility of a higher single‐mode lasing intensity than conventional WGM perovskite microlasers. The results provide new routes to realize high‐performance perovskite microlasers and their potential application in sensing refractive index.

Cylindrical Vector Beam Holography without Preservation of OAM Modes.

Orbital angular momentum (OAM) multiplexed holograms have attracted a great deal of attention recently due to their physically unbounded set of orthogonal helical modes. However, preserving the OAM property in each pixel hinders fine sampling of the target image in principle and requires a fundamental filtering aperture array in the detector plane. Here, we demonstrate the concept of metasurface-based vectorial holography with cylindrical vector beams (CVBs), whose unlimited polarization orders and unique polarization distributions can be used to boost information storage capacity. Although CVBs are composed of OAM modes, the holographic images do not preserve the OAM modes in our design, enabling fine sampling of the target image in a quasi-continuous way like traditional computer-generated holograms. Moreover, the images can be directly observed by passing them through a polarizer without the need for a fundamental mode filter array. We anticipate that our method may pave the way for high-capacity holographic devices.

The role of non-uniform magnetization texture for magnon–magnon coupling in an antidot lattice

We numerically study the spin-wave dynamics in an antidot lattice based on a Co/Pd multilayer structure with reduced perpendicular magnetic anisotropy at the edges of the antidots. This structure forms a magnonic crystal with a periodic antidot pattern and a periodic magnetization configuration consisting of out-of-plane magnetized bulk and in-plane magnetized rims. Our results show a different behavior of spin waves in the bulk and in the rims under varying out-of-plane external magnetic field strength, revealing complex spin-wave spectra and hybridizations between the modes of these two subsystems. A particularly strong magnon–magnon coupling, due to exchange interactions, is found between the fundamental bulk spin-wave mode and the second-order radial rim modes. However, the dynamical coupling between the spin-wave modes at low frequencies, involving the first-order radial rim modes, is masked by the changes in the static magnetization at the bulk–rim interface with magnetic field changes. The study expands the horizons of magnonic-crystal research by combining periodic structural patterning and non-collinear magnetization texture to achieve strong magnon–magnon coupling, highlighting the significant role of exchange interactions in the hybridization.

Corrosion damage identification based on the symmetry of propagating wavefield measured by a circular array of piezoelectric transducers: Theoretical, experimental and numerical studies

The article investigates the results obtained from numerical simulations and experimental tests concerning the propagation of guided waves in corroded steel plates. Developing innovative methodologies for assessing corrosion-induced degradation is crucial for accurately diagnosing offshore and ship structures exposed to harsh environmental conditions. The main aim of the research is to analyze how surface irregularities affect wave propagation characteristics. An investigation was conducted for antisymmetric fundamental mode A0. Specifically, the study examines the asymmetrical wavefronts generated by nonuniform thickness in damaged specimens. Initially, numerical analysis explores the impact of thickness variation on wave field symmetry. Corroded plates with varying levels of degradation are modeled using the random fields approach, with degradation levels ranging from 0 % to 60 %. Subsequently, the research investigates how the standard deviation of thickness distribution (from 5 % to 20 % of the initial thickness) and excitation frequency (from 50 to 150 kHz) influence recorded signals and the shape of reconstructed wavefronts. Each scenario compares wavefront symmetry levels estimated using rotational and bilateral symmetry degrees as indicative parameters. The numerical simulations are complemented by experimental tests conducted on plates with three different degradation levels. The results demonstrate the efficacy of the proposed wave field analysis approach for assessing structural integrity, as evidenced by the agreement between numerical predictions and experimental observations.

Resonant Forcing by Solar Declination of Rossby Waves at the Tropopause and Implications in Extreme Events, Precipitation, and Heat Waves—Part 1: Theory

The purpose of this first article is to provide a physical basis for atmospheric Rossby waves at the tropopause to clarify their properties and improve our knowledge of their role in the genesis of extreme precipitation and heat waves. By analogy with the oceanic Rossby waves, the role played by the pycnocline in ocean Rossby waves is replaced here by the interface between the polar jet and the ascending air column at the meeting of the polar and Ferrel cell circulation or between the subtropical jet and the descending air column at the meeting of the Ferrel and Hadley cell circulation. In both cases, the Rossby waves are suitable for being resonantly forced in harmonic modes by tuning their natural period to the forcing period. Here, the forcing period is one year as a result of the variation in insolation due to solar declination. A search for cause-and-effect relationships is performed from the joint representation of the amplitude and phase of (1) the velocity of the cold or warm modulated airflows at 250 mb resulting from Rossby waves, (2) the geopotential height at 500 mb, and (3) the precipitation rate or ground air temperature. This is for the dominant harmonic mode whose period can be 1/16, 1/32, or 1/64 year, which reflects the intra-seasonal variations in the rising and falling air columns at the meeting of the polar, Ferrel, and Hadley cell circulation. Harmonics determine the duration of blocking. Two case studies referring to extreme cold and heat waves are presented. Dual cyclone–anticyclone systems seem to favor extreme events. They are formed by two joint vortices of opposite signs reversing over a period, concomitantly with the involved modulated airflows at the tropopause. A second article will be oriented toward (1) the examination of different case studies in order to ascertain the common characteristics of Rossby wave patterns leading to extreme events and (2) a map of the globe revealing future trends in the occurrence of extreme events.

Enhanced Photon-Pair Generation Based on Thin-Film Lithium Niobate Doubly Resonant Photonic Crystal Cavity

In this work, a doubly resonant photonic crystal (PhC) cavity is proposed to enhance second harmonic generation (SHG) efficiency and photon pair generation rate (PGR). Through the exploration of geometry parameters, a band-edge mode within the light cone is identified as the first harmonic (FH) mode, and a band-edge mode outside the light cone is designated as the second harmonic (SH). Subsequently, by increasing the layers of the core region, a heterostructure PhC cavity is designed. The results showcase a doubly resonant PhC cavity achieving a 133/W SHG efficiency and a photon pair generation rate of 3.7 × 108/s. The exceptional conversion efficiency is attributed to the high quality factors Q observed in the FH and SH modes with values of approximately 280,000 and 2100, respectively. The remarkably high Q factors compensate for nonlinear efficiency degradation caused by detuning, simultaneously making the manufacturing process easier and more feasible. This work is anticipated to provide valuable insights into efficient nonlinear conversion and photon pair generation rates.

A Multiplexing Optical Temperature Sensing System for Induction Motors Using Few-Mode Fiber Spatial Mode Diversity

Induction motors are widely applied in motor drive systems. Effective temperature monitoring is one of the keys to ensuring the reliability and optimal performance of the motors. Therefore, this paper introduces a multiplexed optical temperature sensing system for induction motors based on few-mode fiber (FMF) spatial mode diversity. By using the spatial mode dimension of FMF, fiber Bragg grating (FBG) carried by different spatial modes of optical paths is embedded in different positions of the motor to realize multipoint synchronous multiplexing temperature monitoring. The paper establishes and demonstrates a photonic lantern-based mode division sensing system for motor temperature monitoring. As a proof of concept, the system demonstrates experiments in multiplexed temperature sensing for motor stators using the fundamental mode LP01 and high-order spatial modes LP11, LP21, and LP02. The FBG sensitivity carried by the above mode is 0.0107 nm/°C, 0.0106 nm/°C, 0.0097 nm/°C, and 0.0116 nm/°C, respectively. The dynamic temperature changes in the stator at different positions of the motor under speeds of 1k rpm, 1.5k rpm, 2k rpm with no load, 3 kg load, and 5 kg load, as well as at three specific speed–load combinations of 1.5k rpm_3 kg, 1k rpm_0kg, 2k rpm_5 kg and so on are measured, and the measured results of different spatial modes are compared and analyzed. The findings indicate that different spatial modes can accurately reflect temperature variations at various positions in motor stator winding.

Influence of the Experimental Setup on Electromagnetic Pulses in the VHF Band at Relativistic High-Power Laser Facilities

We present experimental results for the controlled mitigation of the electromagnetic pulses (EMPs) produced in the interactions of a 1 PW high-power 30 fs Ti:Sa laser VEGA-3 with solid-density targets transparent to laser-forward-accelerated relativistic electrons. This study aims at the band of very high frequencies (VHFs), i.e., those in the hundreds of MHz, which comprise the fundamental cavity modes of the rectangular VEGA-3 vacuum chamber. We demonstrate mode suppression by a tailoring of the laser-produced space charge distribution.

Microwave synthesis of magnesium phosphate-rGO as an effective electrode for supercapacitor application

Abstract Transition metal phosphate based materials is being used for energy storage because of P–O covalent bond which facilitates more storage compared to other transition metals and this covalent bond enhanced the electrochemical performance for supercapacitor applications. Pure magnesium phosphate (Mg3(PO4)2) were synthesized via microwave synthesis as the composite varies with rGO (MgPO-XrGO) X=25,50,75,100mg. The prepared composite materials were examined employing XRD, Raman, FT-IR, SEM and XPS studies. Electrochemical studies (CV, EIS, GCD) of three electrode system for the prepared electrodes were performed using Biologic SP-150 with 2M (H2SO4) as electrolyte. From the XRD results, triclinic structured MgPO was confirmed (JCPDS card #35–0329) and rGO has enhanced the crystallinity of MgPO composite. From Raman analyses, the well graphitization nature of rGO in composite MgPO was identified and from XPS analysis chemical composition of the elements was analyzed. The FT-IR fundamental modes of vibrations of PO 4 3 − ${\text{PO}}_{4}^{3-}$ (γ 1,γ 3,γ 4) were obtained. The electrochemical analysis of the prepared material such as pure and composite materials showed better performance. The high specific capacitance was obtained for MgPO-50rGO because MgPO has high coordination with rGO. As Mg2+ oxidation state has high chemical reactivity compared to other earth metals and other advantage is P–O covalent bond that enhanced the performance of the electrode. By facilitating these advantages, rGO is included as composite to develop the electrode to favor the practical applications. By using the optimum level rGO composite with MgPO4-50rGO a better new candidate was successfully developed for supercapacitor applications. The fabricated MgPO-50rGO//Activate carbon full cell set up exhibited the specific capacitance 61 Fg−1 at 1 Ag−1, 21.7 Wh kg−1 energy density and 790.0 W kg−1 power densities and explored outstanding capacitive retention in 2 electrode full cell setup cyclic stability of 99.1 % over the 5000 cycles.

Synthesis, Crystal Structure, and Optical and Magnetic Properties of the New Quaternary Erbium Telluride EuErCuTe3: Experiment and Calculation.

This paper reports for the first time on a new layered magnetic heterometallic erbium telluride EuErCuTe3. Single crystals of the compound were obtained from the elements at 1120 K using CsI as a flux. The crystal structure of EuErCuTe3 was solved in the space group Cmcm (a = 4.3086(3) Å, b = 14.3093(9) Å, and c = 11.1957(7) Å) with the KZrCuS3 structure type. In the orthorhombic structure of erbium telluride, distorted octahedra ([ErTe6]9-) form two-dimensional layers (Er(Te1)2/2e(Te2)4/2k-)∞2, while distorted tetrahedra ([CuTe4]7-) form one-dimensionally connected substructures (Cu(Te1)2/2e(Te2)2/1t5-∞1) along the [100] direction. The distorted octahedra and tetrahedra form parallel two-dimensional layers (CuErTe32-∞2) between which Eu2+ ions are located in a trigonal-prismatic coordination environment (EuTe610-). The trigonal prisms are connected by faces, forming chains (Eu(Te1)2/2(Te2)4/22-∞1) along the [100] direction. Regularities in the variations in structural parameters were established in the series of erbium chalcogenides (EuErCuCh3 with Ch = S, Se, and Te) and tellurides (EuLnCuTe3 with Ln = Gd, Er, and Lu). Ab-initio calculations of the crystal structure, phonon spectrum, and elastic properties of the compound EuErCuTe3 were performed. The types and wavenumbers of fundamental modes were determined, and the involvement of ions in the IR and Raman modes was assessed. The experimental Raman spectra were interpreted. The telluride EuErCuTe3 at temperatures below 4.2 K was ferrimagnetic, as were the sulfide and selenide derivatives (EuErCuCh3 with Ch = S and Se). Its experimental magnetic characteristics were close to the calculated ones. The decrease in the magnetic phase transition temperature in the series of the erbium chalcogenides was discovered.

Temperature-Switch-Controlled Second Harmonic Mode Sensor for Brain-Tissue Detection.

Identifying brain-tissue types holds significant research value in the biomedical field of non-contact brain-tissue measurement applications. In this paper, a layered metastructure is proposed, and the second harmonic generation (SHG) in a multilayer metastructure is derived using the transfer matrix method. With the SHG conversion efficiency (CE) as the measurement signal, the refractive index ranges that can be distinguished are 1.23~1.31 refractive index unit (RIU) and 1.38~1.44 RIU, with sensitivities of 0.8597 RIU-1 and 1.2967 RIU-1, respectively. It can distinguish various brain tissues, including gray matter, white matter, and low-grade glioma, achieving the function of a second harmonic mode sensor (SHMS). Furthermore, temperature has a significant impact on the SHG CE, which can be used to define the switch signal indicating whether the SHMS is functioning properly. When the temperature range is 291.4~307.9 Kelvin (K), the temperature switch is in the "open" state, and the optimal SHG CE is higher than 0.298%, indicating that the SHMS is in the working state. For other temperature ranges, the SHG CE will decrease significantly, indicating that the temperature switch is in the "off" state, and the SHMS is not working. By stimulating temperature and using the response of SHG CE, the temperature-switch function is achieved, providing a new approach for temperature-controlled second harmonic detection.

Multiphysics simulations of a cylindrical waveguide optical switch using phase change materials on silicon

This work presents the design and multiphysics simulation of a cylindrical waveguide-based optical switch using germanium-antimony-tellurium (GST) as an active phase change material. The innovative cylindrical architecture is theoretically analyzed and evaluated at 1550 nm wavelength for telecommunication applications. The dispersion relation is derived analytically for the first time to model the optical switch, while finite element method (FEM) and finite difference time domain (FDTD) techniques are utilized to simulate the optical modes, light propagation, and phase change dynamics. The fundamental TE01 and HE11 modes are studied in detail, enabling switching between low-loss amorphous and high-loss crystalline GST phases. Increasing the GST thickness is found to increase absorption loss in the crystalline state but also slows down phase transition kinetics, reducing switching speeds. A 10 nm GST layer results in competitive performance metrics of 0.79 dB insertion loss, 13.47 dB extinction ratio, 30 nJ average power consumption, and 3.5 Mb/s bit rate. The combined optical, thermal, and electrical simulation provides comprehensive insights towards developing integrated non-volatile photonic switches and modulators utilizing phase change materials.

Two port high gain and low mutual coupling dielectric resonator based array antenna for 5G mm-wave applications

In this communication, a two-port ceramic based array radiator at mm-wave frequency range is structured and analysed. 3-dB power divider based microstrip feed line is utilised to excite the rectangular aperture. The same aperture is used to feed the ceramic, which creates fundamental hybrid mode (HEM11δ ) inside the dielectric resonator. Feeding structure is designed on RT Duroid substrate having thickness 0.254 mm and permittivity 2.2. The length and width of the substrate is 60.0 mm and 30.0 mm respectively. Alumina material is used to design the ceramic having permittivity 9.8. The exclusive feature of the proposed antenna design is to get highly directional pattern along with high gain (more than 13.5 dBi) in mm-wave frequency range with the assistance of 1*4 array structure. Orthogonal orientation of antenna ports adds the polarization diversity concept, which in turns improve the isolation level more than 50 dB. Measured results confirm that the designed antenna works effectively in between 31.5–32.8 GHz. Broadside radiation pattern and good value of Envelop correlation coefficient (less than 0.1)/Diversity gain (10.0 dB) make the designed antenna employable for n257 frequency band of 5G mm-wave applications.

Dynamic embedding of effective harmonic normal mode vibrations in all-atomistic energy gap fluctuations: Case study of light harvesting 2 complex.

Environmental effects in excitation energy transfer have mostly been modeled by baths of harmonic oscillators, but to what extent such modeling provides a reliable description of actual interactions between molecular systems and environments remains an open issue. We address this issue by investigating fluctuations in the excitation energies of the light harvesting 2 complex using a realistic all-atomistic simulation of the potential energy surface. Our analyses reveal that molecular motions exhibit significant anharmonic features, even for underdamped intramolecular vibrations. In particular, we find that the anharmonicity contributes to the broadening of spectral densities and substantial overlaps between neighboring peaks, which complicates the meaning of mode frequencies constituting a bath model. Thus, we develop a strategy to construct a minimally underdamped harmonic bath that has a clear connection to all-atomistic dynamics by utilizing actual normal modes of molecules but optimizing their frequencies such that the resulting bath model can best reproduce the all-atomistic simulation results. By subtracting the underdamped contribution from the entire fluctuations, we also show that identifying a residual spectral density representing all other contributions with overdamped behavior is possible. We find that this can be fitted well with a well-established analytic form of a spectral density function or, alternatively, modeled as explicit time dependent fluctuations with muti-exponential or power law type correlation functions. We provide an assessment and the implications of these possibilities. The approach presented here can also serve as a general strategy to construct a simplified bath model that can effectively represent the underlying all-atomistic bath dynamics.

Phase-shifted third harmonic modulation technique for induction heating applications to improve soft switching capability

Phase-shifted third harmonic modulation technique for induction heating applications to improve soft switching capability

Magnetoelectric effect in a Metglas–langatate ring heterostructure for current sensing

The magnetoelectric (ME) effect was observed and investigated in a planar ring-type heterostructure containing mechanically coupled rings of magnetostrictive amorphous alloy Metglas and a piezoelectric single crystal langatate. The structure was excited by a circumferential ac magnetic field in the presence of a circumferential dc bias magnetic field. Due to the absence of demagnetization and the high acoustic quality factor of the langatate, a high ME field conversion coefficient of α E ≈ 53 V (Oe cm)−1 was obtained at the frequency 221 kHz of the fundamental radial acoustic resonance mode. The structure can be used as a non-contact ac or dc current sensor. The sensitivity of the structure to the ac current was 1.6 V A−1, whereas for the dc current it reached 4.2 V A−1.

Dead Zone Fault Detection Optimization Method for Few-Mode Fiber Links Based on Unexcited Coupled Higher-Order Modes

Dead Zone Fault Detection Optimization Method for Few-Mode Fiber Links Based on Unexcited Coupled Higher-Order Modes