Growth Process Research Articles

On the elastoplastic behavior in collisional compression of spherical dust aggregates

Aggregates consisting of submicron-sized cohesive dust grains are ubiquitous, and understanding the collisional behavior of dust aggregates is essential. It is known that low-speed collisions of dust aggregates result in either sticking or bouncing, and local and permanent compaction occurs near the contact area upon collision. In this study, we perform numerical simulations of collisions between two aggregates and investigate their compressive behavior. We find that the maximum compression length is proportional to the radius of aggregates and increases with the collision velocity. We also reveal that a theoretical model of contact between two elastoplastic spheres successfully reproduces the size- and velocity-dependence of the maximum compression length observed in our numerical simulations. Our findings on the plastic deformation of aggregates during collisional compression provide a clue to understanding the collisional growth process of aggregates.Graphic abstract

Physical Mechanisms of Improved Performance of Scaffolded Zinc-Silver Battery Cathodes.

Nanostructuring can greatly improve the electrode stability of rechargeable battery systems, such as Zn-Ag. In this report, we investigate the physical mechanisms by which nanostructuring alters structural properties of nanomaterials and thereby influences the structural stability of electrodes. We specifically consider the effects of Au-based nanoscaffolds on Ag. Through density functional theory calculations, we propose that the charge transfer at the Au-Ag interface can facilitate the formation of Ag2O from Ag centers. Structural analysis of samples prepared in this work shows that Ag2O is extruded from Au-Ag material in the form of sheets. Interestingly, the length scale of such protrusions depends on the Au mole fraction that significantly alters the system's overall structural morphology. We rationalize these findings via kinetic Monte Carlo simulations of the Ag2O growth process and highlight the role of Au as a heterogeneous nucleation center.

Achieving significant grain refinement efficiency in Mg-Al alloys via a GNP@MgO composite refiner

Master alloys containing Zirconium (Zr) serve as effective grain refiners in most commercial cast magnesium (Mg) alloys. However, their efficacy is diminished in Mg–Al series alloys due to the formation of Al–Zr compounds. In this work, a novel Mg-GNP@MgO master alloy was prepared utilizing the in-situ reaction between CO2 and Mg. The grain refinement efficiency of this composite inoculation on Mg–9Al alloys was systematically investigated using SEM-EBSD, HRTEM observations, Density Functional Theory (DFT), and Sharp Interface Model (SIM) calculations. The findings suggest that the composite grain refiner (GNP@MgO) exerted a notable refining influence on Mg–9Al alloy. Through the conventional casting process, the average grain size was refined to approximately 13 μm upon the addition of 3 vol% GNP@MgO, achieving a grain refinement efficiency of 90 %. The enhanced refining efficiency arises from the synergistic control over the nucleation and growth processes of α-Mg grains, facilitated by GNP@MgO particles. This process includes improved heterogeneous nucleation, triggered by the newly formed Al4C3 phases through the interaction between GNPs and Al element, followed by the limited expansion of α-Mg grains induced by the nano-sized MgO particles. The MgO particles predominantly gather around grain boundaries to establish stable nano-coating layers, thereby exerting a substantial Zener pinning effect. The pinning role played by the MgO nanoparticles was also verified by a sharp interface model. The findings in this work not only carve out a new avenue for the grain refinement of cast Mg–Al alloys but also inspire fresh perspectives for the development of novel grain refiners.

The effect of subcooling on hydrate generation and solid deposition with two-phase flow of pure water and natural gases

Deepwater oil and gas transportation systems play a crucial role in energy supply, but also face the challenges of hydrate generation and blockage. The study observed hydrate generation and deposition at different subcooling degrees and flow rates by using a high-pressure fully visualized recirculation pipeline. It was found that the subcooling degree has a nonlinear positive correlation with the total amount of hydrate generated. The hydrate formation at 11.7 °C subcooling was 4.5 times higher than that at 9 °C subcooling. According to the hydrate conversion rate analysis, the hydrate growth process under low subcooling conditions directly transitions from the bubble-promoting zone to the termination point of hydrate generation. Combined with the deposition state of the pipe wall and the differential pressure change curves, the risk of blockage at different subcooling levels and flow rates can be assessed.

Classification of tomato seedling chilling injury based on chlorophyll fluorescence imaging and DBO-BiLSTM

IntroductionTomatoes are sensitive to low temperatures during their growth process, and low temperatures are one of the main environmental limitations affecting plant growth and development in Northeast China. Chlorophyll fluorescence imaging technology is a powerful tool for evaluating the efficiency of plant photosynthesis, which can detect and reflect the effects that plants are subjected to during the low temperature stress stage, including early chilling injury.MethodsThis article primarily utilizes the chlorophyll fluorescence image set of tomato seedlings, applying the dung beetle optimization (DBO) algorithm to enhance the deep learning bidirectional long short term memory (BiLSTM) model, thereby improving the accuracy of classification prediction for chilling injury in tomatoes. Firstly, the proportion of tomato chilling injury areas in chlorophyll fluorescence images was calculated using a threshold segmentation algorithm to classify tomato cold damage into four categories. Then, the features of each type of cold damage image were filtered using SRCC to extract the data with the highest correlation with cold damage. These data served as the training and testing sample set for the BiLSTM model. Finally, DBO algorithm was applied to enhance the deep learning BiLSTM model, and the DBO-BiLSTM model was proposed to improve the prediction performance of tomato seedling category labels.ResultsThe results showed that the DBO-BiLSTM model optimized by DBO achieved an accuracy, precision, recall, and F1 score with an average of over 95%.DiscussionCompared to the original BiLSTM model, these evaluation parameters improved by 9.09%, 7.02%, 9.16%, and 8.68%, respectively. When compared to the commonly used SVM classification model, the evaluation parameters showed an increase of 6.35%, 7.33%, 6.33%, and 6.5%, respectively. This study was expected to detect early chilling injury through chlorophyll fluorescence imaging, achieve automatic classification and labeling of cold damage data, and lay a research foundation for in-depth research on the cold damage resistance of plants themselves and exploring the application of deep learning classification methods in precision agriculture.

Over-expression of LsEXPA6, a lettuce expansin gene, improves cadmium stress tolerance in transgenic Arabidopsis

Cadmium (Cd) is a harmful heavy metal that is highly toxic to plants and animals. Expansins are cell wall proteins inducing cell wall loosening and participate in all plant growth and development processes which are associated with cell wall modifications. We investigated lettuce’s expansin gene LsEXPA6 and found that LsEXPA6 overexpression Arabidopsis lines were much more resistant to cadmium stress. Our results revealed that the root system of the expa6 mutant was suppressed under cadmium stress, resulting in shorter plant height, reduced biomass, and a significant increase in cadmium content in the plants compared with wild-type plants, whereas LsEXPA6 overexpression lines had a well-developed root system and reduced cadmium accumulation in the roots and shoots of the plants. The above results indicated that overexpression of LsEXPA6 affected root development and reduced Cd absorption in Arabidopsis. In addition, the higher absorption capacity of nutrients, increased antioxidant enzymes activities, improved chlorophyll and photosynthetic function in the overexpression Arabidopsis plants, supported the Cd stress tolerance mechanism. Taken together, these results provided a new insight on the role of expansin proteins in the tolerance of plants to Cd stress by root cell elongation.

In Situ Studies on the Influence of Surface Symmetry on the Growth of MoSe2 Monolayer on Sapphire Using Reflectance Anisotropy Spectroscopy and Differential Reflectance Spectroscopy

The surface symmetry of the substrate plays an important role in the epitaxial high-quality growth of 2D materials; however, in-depth and in situ studies on these materials during growth are still limited due to the lack of effective in situ monitoring approaches. In this work, taking the growth of MoSe2 as an example, the distinct growth processes on Al2O3 (112¯0) and Al2O3 (0001) are revealed by parallel monitoring using in situ reflectance anisotropy spectroscopy (RAS) and differential reflectance spectroscopy (DRS), respectively, highlighting the dominant role of the surface symmetry. In our previous study, we found that the RAS signal of MoSe2 grown on Al2O3 (112¯0) initially increased and decreased ultimately to the magnitude of bare Al2O3 (112¯0) when the first layer of MoSe2 was fully merged, which is herein verified by the complementary DRS measurement that is directly related to the film coverage. Consequently, the changing rate of reflectance anisotropy (RA) intensity at 2.5 eV is well matched with the dynamic changes in differential reflectance (DR) intensity. Moreover, the surface-dominated uniform orientation of MoSe2 islands at various stages determined by RAS was further investigated by low-energy electron diffraction (LEED) and atomic force microscopy (AFM). By contrast, the RAS signal of MoSe2 grown on Al2O3 (0001) remains at zero during the whole growth, implying that the discontinuous MoSe2 islands have no preferential orientations. This work demonstrates that the combination of in situ RAS and DRS can provide valuable insights into the growth of unidirectional aligned islands and help optimize the fabrication process for single-crystal transition metal dichalcogenide (TMDC) monolayers.

Timing mowing for maximal energy gain - Managing foraging habitat of wintering geese under extreme drought conditions

The availability of high-quality food resources is a critical determinant of wildlife fitness. Over the past two decades, phenological mismatch - the temporal misalignment between animals’ peak nutrient demand and optimal resource availability - has emerged as a significant conservation challenge. This issue is particularly worrisome for migratory birds, which must accumulate energy reserves to meet the elevated metabolic demands of migration between breeding and wintering grounds. In Poyang Lake, a crucial wintering ground along the East Asian-Australasian flyway, increasing asynchrony between vegetation growth and the migration of herbivorous waterbirds significantly impedes conservation efforts and presents a major management challenge for this Ramsar wetland. This study evaluates the efficacy of mowing, a grassland management measure, in regulating plant growth processes and restoring food resources for geese. In-situ mowing experiments were conducted with varying timings in Carex wet meadows, the primary foraging habitats of geese. Optimal mowing times were identified, and the maximum goose carrying capacity was assessed by comparing Carex growth and nutritional dynamics with goose dietary requirements. The results reveal that mowing effectively slows down the aging process of Carex, and protein content is identified as a critical limiting factor for geese foraging. Different mowing timings extend the suitable foraging period by 11–25 days. Estimates suggest varying carrying capacities with different mowing timings, supporting goose populations ranging from 133 to 2,046 in Changhuchi Lake during wintering. The optimal mowing window is early October, avoiding dates before late September and after late November. Moreover, multiple-stage mowing is recommended to accommodate different wintering stages. The study highlights mowing as a potential habitat restoration approach for goose conservation, effectively mitigating the challenges imposed by phenological mismatch directly and indirectly caused by anthropogenic activities.

Genome-wide survey of KT/HAK/KUP genes in the genus Citrullus and analysis of their involvement in K+-deficiency and drought stress responses in between C. lanatus and C. amarus

BackgroundThe KT/HAK/KUP is the largest K+ transporter family in plants, playing crucial roles in K+ absorption, transport, and defense against environmental stress. Sweet watermelon is an economically significant horticultural crop belonging to the genus Citrullus, with a high demand for K+ during its growth process. However, a comprehensive analysis of the KT/HAK/KUP gene family in watermelon has not been reported.Results14 KT/HAK/KUP genes were identified in the genomes of each of seven Citrullus species. These KT/HAK/KUPs in watermelon were unevenly distributed across seven chromosomes. Segmental duplication is the primary driving force behind the expansion of the KT/HAK/KUP family, subjected to purifying selection during domestication (Ka/Ks < 1), and all KT/HAK/KUPs exhibit conserved motifs and could be phylogenetically classified into four groups. The promoters of KT/HAK/KUPs contain numerous cis-regulatory elements related to plant growth and development, phytohormone response, and stress response. Under K+ deficiency, the growth of watermelon seedlings was significantly inhibited, with cultivated watermelon experiencing greater impacts (canopy width, redox enzyme activity) compared to the wild type. All KT/HAK/KUPs in C. lanatus and C. amarus exhibit specific expression responses to K+-deficiency and drought stress by qRT-PCR. Notably, ClG42_07g0120700/CaPI482276_07g014010 were predominantly expressed in roots and were further induced by K+-deficiency and drought stress. Additionally, the K+ transport capacity of ClG42_07g0120700 under low K+ stress was confirmed by yeast functional complementation assay.ConclusionsKT/HAK/KUP genes in watermelon were systematically identified and analyzed at the pangenome level and provide a foundation for understanding the classification and functions of the KT/HAK/KUPs in watermelon plants.

Interaction of defects, martensitic transformation and slip in metastable body centred cubic crystals of Ti-10V-2Fe-3Al: A study via crystal plasticity finite element methods (CPFEM)

Metastable β titanium alloys are widely applied in many industries. These alloys can have plastic deformation via dislocation slip, twinning, stress-induced martensite (SIM), or a combination of these. These alloys fail in a ductile manner via a process of void nucleation, growth, and coalescence. Inherent defects, such as voids, are commonly attributed to poor mechanical properties. In this study, aspects of plastic anisotropy in damage accumulation are investigated for metastable crystals that deform by combined slip and SIM. The focus of this study is to understand the evolution of damage due to inherent voids in metastable Ti-10V-2Fe-3Al single crystals. This investigation is conducted using crystal plasticity-based 3D finite element (FE) calculations. A unit-cell FE model involving a spherical void is deformed under constant stress triaxiality and lode parameter. We investigated four triaxiality values at differing lode parameters in three crystal orientations. The void growth was found to be heavily dependent on crystal orientation at low triaxialities. At higher triaxialities, SIM is found to inhibit the void growth via accommodation of the required deformation in the surrounding material. Orientations aligned favourable with SIM undergo significantly less void growth. The accommodation of deformation in the surrounding matrix was found to help preserve the integrity of the void, preventing the localisation of deformation around the void. At lower lode parameter and at higher stress triaxiality this impedes the exponential growth of the void. While, at higher lode parameter with low triaxiality SIM was found to delay the collapse of the void into a crack like morphology. This study not only deepens our understanding of the mechanical behaviour of metastable β titanium alloys, but also unveils the complex interplay between inherent defects, stress-induced martensite, and slip-based plasticity within their crystalline structure, offering fresh perspectives on enhancing material performance.

Preparation of poly(acrylonitrile-co-styrene) microspheres by reflux precipitation polymerization

Poly(acrylonitrile-co-styrene) microspheres are utilized in several applications due to their superior mechanical properties, excellent chemical stability, and tunable surface modification. In this work, poly(acrylonitrile-co-styrene) microspheres were synthesized in ethyl acetate usingreflux precipitation polymerization. The average particle size and morphology of microspheres were carefully measured to investigate the responding influencing factors. In the growth process of these microspheres, the average particle size of poly(AN-co-St) microspheres changed a little after 180 min. However, the yield of the microspheres continued to increase until 420 min. The properties of the solvents had a significant impact on both the average particle size and the morphology of the poly(AN-co-St) microspheres. The concentrations of the initiator and the cross-linker have minimal effect on the average particle size of poly(AN-co-St) microspheres. By controlling the monomer content at 25 wt%, the yield of these microspheres could reach 82%. The method is straightforward to operate andthe prepared microspheres exhibithigh sphericity and uniformity. As a result, it shows great promise for thepreparation of submicron poly(AN-co-St) microspheres.

When inclusive growth is not enough: advances and limitations of development policies in Uruguay 2005–2019

ABSTRACT Along most of the 2005–2019 period, Uruguay experienced an impressive economic growth. The country extended its public policies across industrial, technological, and social domains. However, there was a dearth of significant structural changes, constraining Uruguay’s ability to embark on a sustained developmental trajectory. Our findings reveal that the majority of implemented policies were designed to enhance competitiveness and build capabilities horizontally, rather than promoting structural changes. This allows us to discuss the dynamic nature of developmental processes marked by increasing policy challenges. In doing so, we stress the relevance of policy support and coordination to sustain inclusive growth processes.

Body Height of MPS I and II Patients after Hematopoietic Stem Cell Transplantation: The Impact of Dermatan Sulphate.

Hematopoietic stem cell transplantation (HSCT) comprises one of the two main treatment regimens for patients with mucopolysaccharidoses (MPS). There is a scarcity of literature concerning the process of growth in children with Mucopolysaccharidosis type I (MPS I) and Mucopolysaccharidosis type I (MPS II) after HSCT. The aim of this manuscript was to evaluate the therapeutic effect of HSCT on the heights of patients with MPS I and MPS II. It was an observational, single-center study on patients with MPS I and II treated with HSCT. 6 MPS patients, including 4 MPS I and 2 MPS II, underwent HSCT at a median age of 2 years. All patients are alive to date, with a median age of 7.7 years (range 5.5-12 years) at the last follow-up. In both (MPS I and MPS II) groups of patients treated with HSCT, the growth rate was higher than in untreated patients and was found to be in line with the population norm. In both MPS I and MPS II patients who were treated with HSCT, normalization of urinary GAG excretion was observed. Additionally, no bands of DS and HS in GAG electrophoresis were visible. Both MPS I and MPS II patients presented height gain after HSCT compared to the curves of untreated patients. The absence of dermatan sulphate after HSCT could lead to normal growth in bone length.

Joseph Schumpeter, Allyn Young, and the future of capitalism

Schumpeter placed the entrepreneur and innovation at the center of capitalism and thought that once monopoly capitalism inevitably emerges, the link between individual initiative and innovation will be broken. Capitalism will then undermine its own institutional context and socialism would ultimately emerge. But his support for socialism was nuanced and restricted to mature capitalism; for him, unfettered capitalism was preferable to socialism with fascist features. For Young Smith’s relationship between the division of labor and market size was central to growth, and the role of the entrepreneur was more to find markets than innovation. The objective of this paper is to analyze the contrasting views of Schumpeter and Young on endogenous process of growth and the future of capitalism itself, particularly pertaining to the emergence of monopoly capitalism.

Directional self-assembly of organic vertically superposed nanowires

Organic crystal-based superimposed heterostructures with inherent multichannel characteristics demonstrate superior potential for manipulating excitons/photons at the micro/nanoscale for integrated optoelectronics. However, the precise construction of organic superimposed heterostructures with fixed superimposed sites remains challenging because of the random molecular nucleation process. Here, organic vertically superimposed heterostructures (OSHs) with fixed superimposed positions are constructed via semi-wrapped core/shell heterostructures with partially exposed cores, which provide preferential nucleation sites for further molecular epitaxial growth processes. Furthermore, the relative length ratio from 21.7% to 95.3% between interlayers is accurately adjusted by regulating the exposed area of the semi-wrapped core/shell heterostructures. Significantly, these OSHs with anisotropic optical characteristics demonstrate well regulation of excitation position-dependent waveguide behaviors and can function as photonic barcodes for information encryption. This strategy provides a facile approach for controlling the nucleation sites for the controllable preparation of organic heterostructures and advanced applications for integrated optoelectronics.

Molecular dynamics simulation study of graphene synthesis by rotating arc plasma

The rotating arc plasma method, based on its unique characteristics, provides a simple, efficient, and catalyst-free approach for graphene material synthesis. This study employs molecular dynamics simulations to theoretically investigate the detailed growth process of graphene at the atomic scale using plasma. During the growth process, different radicals serve as dissociation precursors within the plasma. Simulation results indicate that the growth process of graphene clusters involves three stages: extension of carbon clusters, cyclization of carbon chains, and coalescence of clusters into sheets. Firstly, the precursor concentration affects the size of graphene clusters; increasing the precursor concentration enlarges the cluster size but also increases the likelihood of curling. Secondly, increasing the hydrogen content in the precursor can reduce the growth rate of clusters, decrease dangling bonds at the periphery of clusters, thereby slowing down cluster closure and maintaining a well-defined sheet structure. Lastly, appropriately elevating the simulation temperature can enhance the reaction rate during the simulation process without altering the reaction pathway. These research findings establish the foundation for understanding the growth mechanism of graphene.

Heterogeneous atoms mediated formation MnCo2S4/PNG heterostructures for high-performance supercapacitors

Transition metal sulfides are considered as potential electrode materials for high performance energy storage devices. However, structural instability during electrochemical reactions has seriously hindered their wide applications. In this study, we demonstrate that MnCo2S4/PNG (N- and P-doped graphene) composite constructed with hetero-atomic induction exhibits excellent morphological stability. Heterogeneous atoms doping on graphene can change its surface charge distribution. Under the induced effect of surface charge, the crystal growth and assembly process of MnCo2S4 nanostructure are changed as well, which leads to MnCo2S4 nanoparticles (NPs) uniformly anchored on the curled and folded PNG layer. In this case, it avoids the agglomeration of MnCo2S4 NPs, and thus increasing the specific surface area and pore volume of the composite, which is conducive to the full contact between the electrode and the electrolyte and therefore the rapid diffusion rate of the electrolyte ions at the interfaces. The obtained 1.4MnCo2S4/PNG material has a specific capacitance of 2465 F g−1 at 1 A g−1. In addition, the electrode possesses high conductivity, excellent rate performance and cyclic stability. The assembled 1.4MnCo2S4/PNG//PNG asymmetric supercapacitor yields an energy density of up to 65.1 Wh kg−1 under the power density of 800 W kg−1, showing excellent energy storage characteristics.

Preparation of robust superhydrophobic stainless steel mesh for Oil-Water separation through Mn-Assisted control of one-step electrodeposited Zn growth

Removing oil spills from water presents a significant challenge in environmental remediation. Among various separation materials available, superhydrophobic materials have emerged as promising solutions, notable for their efficiency, cost-effectiveness, and eco-friendliness. The precise control of micro/nanostructure synthesis plays an essential role in creating superhydrophobic surfaces. Herein, the present study demonstrates controlled growth of well-defined hexagonal platelet-like micro/nanostructures of zinc crystals. This is achieved through deliberate manipulation of the electrodeposition crystal growth process, a facet frequently disregarded in previous studies. Notably, the present work, based on the distinctive properties of the Zn hexagonal close-packed structure (hcp), focuses on the effects of incorporating Mn and deposition parameters on the performance of Zn coatings. These findings offer valuable insights into selectively constructing Zn crystal planes for future electrodeposition endeavors. The resulting zinc/manganese stearate (SZM) coating on stainless steel mesh (SSM) shows remarkable water contact angles, reaching an impressive 163.1 ± 2.4°, in accordance with the Cassie-Baxter theory. This feature facilitates highly efficient oil–water separation. Coupled with size sieving of SSM, SZM coatings exhibit an oil–water separation efficiency of up to 99.86 % and a flux as high as 55.58 kL/m2h. Furthermore, the SZM coating exhibits long-lasting superhydrophobicity and exceptional corrosion resistance, even when subjected to challenging conditions such as high temperatures up to 200℃, pressure reaching 7 kg/cm2, or exposure to chemical and mechanical stresses. These enduring properties make SZM coatings suitable for constructing gravity-based and continuous oil–water separation systems, establishing them as a practical solution for diverse oil–water separation applications.

Evaluating the Impact of UVC Exposure on Forage Maize Seeds under Hydroponic Condition

Background: UV radiation, with shorter wavelengths than visible light, plays a pivotal role in stimulating growth processes and boosting the synthesis of beneficial compounds in plants. Moreover, it triggers morphological changes and genetic responses, shaping plants’ physical traits and adaptability. Nevertheless, a nuanced understanding is necessary as excessive UV exposure can also cause harm, underscoring the complexity of the relationship between UV radiation and plants. The study aimed to evaluate the effect of ultraviolet C (UVC) light exposure on the germination and growth of forage maize seeds under controlled conditions in an indoor crop. One sample of seeds was exposed to UVC light, while the other was not. Methods: The experiment was carried out for 14 days, with the plants subjected to mixed blue-red light, fertigation and kept at a maximum external temperature of 30°C and maximum internal temperature of 25.1°C. UVC light is applied for 10 minutes to the seeds before germination. Result: The results showed that the plants exposed to UVC light had an average growth increase of 3cm compared to those that did not receive the treatment. However, the protein content of both sets of seedlings was similar. The study suggests that further research is necessary to determine the optimal duration and distance for UVC exposure to minimize any potential negative effects on the plants. It also highlights the need to investigate the effect of UVC radiation on the nutritional content of hydroponic crops to ensure that the increased growth does not come at the expense of nutritional quality. The experiment was carried out in Medellin, Colombia, with a maximum solar radiation of 1000 W/m2 and an altitude of 1500 meters. Overall, the study provides evidence that UVC radiation can enhance the growth of hydroponic maize seedlings, but more research is needed to fully understand its effects. At the end, there is an improvement in the growth of forage corn in seeds that have been subjected to UVC light compared to those that have not. It is worth highlighting the need for more research on changes in nutritional components in general.

A machine-learning interatomic potential to study dry/wet oxidation process of silicon

We developed an accurate and efficient machine learning potential with DFT accuracy and applied it to the silicon dry/wet oxidation process to investigate the underlying physics of thermal oxidation of silicon (001) surfaces. The accuracy of the potential was verified by comparing the melting point and structural properties of silicon, the structural properties of a-SiO2, and the adsorption properties on the silicon surface with experiment and DFT data. In subsequent thermal oxidation simulations, we successfully reproduced the accelerated growth phenomenon of the wet oxidation in the experiment, discussed the oxide growth process in detail, and elucidated that the accelerated growth is due to hydrogen in the system that both enhances the adsorption of oxygen on the silicon surface and promotes the migration of oxygen atoms. Finally, we annealed the oxidized structure, counted the defect information in the structure before and after annealing, and analyzed the defect evolution behavior during the annealing process.