Ground Structure Research Articles

Using copper-coated round rod electrodes at various depths in freshwater marshes

Purpose: High-voltage electrical equipment requires a grounding installation in order to protect lives in freshwater swamps with a hydrogen potential of 6.75. To build a grounding structure, it is required to know the resistance value and grounding materials, namely copper-coated rod electrodes at different depths.
 Research methodology: The research was conducted in a freshwater swamp close to the shampooing substation using field observations and direct measurement of soil resistance values, followed by a literature review and comparisons using COMSOL simulation and FEM Analysis.
 Results: The results of direct research and simulations indicate that in order to accomplish a grounding resistance value < 5 ohms according to the PUIL 2011 standard for a single rod system made of copper, it is necessary to optimize the depth of the grounding electrode within a range of 10 meters, which differs from the simulation results of ground resistance measurement and the Comsol application. The percentage error is 1.05%.
 Limitations: This research analyzes the results of measurements and grounding analysis using Comsol Multiphysics at a depth of 1 meter for a particular type of copper-coated round rod electrode at depths of 1, 1.5, and 2 meters.
 Contributions: The results of the study offer information on the usefulness of grounding resistance in freshwater wetlands with a pH greater than 6, where several rod electrode types are utilized to compare future research.

Design process of a compact Tri-Band MIMO antenna with wideband characteristics for sub-6 GHz, Ku-band, and Millimeter-Wave applications

This article proposes a tri–band Multiple Input Multiple Output (MIMO) antenna operating at 5.2 – 5.7 GHz (5G Wi–Fi), 11.8 GHz – 17.3 GHz (Ku–band), and 23.4 GHz – 37.3 GHz (5G millimeter–Wave) frequency bands. The proposed MIMO antenna consists of a 2 × 2 configuration with a defective ground structure on Rogers–5880 substrate. An innovative passive decoupling structure, featuring thin microstrip lines positioned between the radiating elements, has been meticulously engineered to ensure a high level of isolation, achieving values of less than −20 dB. The peak gain of the MIMO antenna is found to be 3.05 dB, 5.27 dB, and 6.97 dB at 5.5 GHz, 17 GHz, and 35.5 GHz frequency bands, respectively. Measured ECC is less than 0.007, and DG is greater than 9.96. The radiation efficiency is above 90 %, TARC is less than –10 dB and channel capacity loss is below 0.4 Bits/s/Hz in all the bands of operation. The simulated and measured results are found to be in good agreement and the proposed MIMO antenna offers numerous advantages, including extensive frequency coverage, broad bandwidth, exceptional isolation, high gain, and efficiency. Consequently, it emerges as a promising choice for devices operating in Sub-6 GHz, Ku-band, and millimeter-wave applications.

Multi-d-Occupancy as an Alternative Definition for the Double d-Shell Effect.

Despite the prevalence of first-row transition metal-containing compounds in virtually all areas of chemistry, the accurate modeling of these systems is a known challenge for the theoretical chemistry community. Such a challenge is shown in a myriad of facets; among them are difficulties in defining ground-state multiplicities, disagreement in the results from methods considered highly accurate, and convergence problems in calculations for excited states. These problems cause a scarcity of reliable theoretical data for transition metal-containing systems. In this work, we explore the double d-shell effect that plagues and makes the application of multireference methods to this type of system difficult. We propose an alternative definition for this effect based on the mixing among d-occupancy configurations or the multi-d-occupancy character of the wave function. Moreover, we present a protocol able to include this effect in multireference calculations using an active space smaller than that usually used in the literature. A molybdenum-copper model system and its copper subsystem are used as example study cases, in particular, the molybdenum-copper charge transfer of the former and the electron affinity of the latter. We have shown that our alternative definition can be used to analyze their reference wave functions qualitatively. Based on this qualitative description, it is possible to optimize an active space without a second d-shell able to obtain relative energies accurately. Seeing the double d-shell effect through the lens of a multi-d-occupancy character, it is possible to correctly describe the wave function, improve the accuracy of the relative energies, and reduce the computational cost of multireference calculations. That way, we believe that this alternative definition has the potential to improve the modeling of first-row transition metal-containing compounds both for their ground and excited electronic structures.

An antenna array utilizing slotted conductive slab: inspired by metasurface and defected ground plane techniques for flexible electronics and sensors operating in the millimeter-wave and terahertz spectrum

This paper describes an innovative design of an antenna array that is metamaterial inspired using sub-wavelength slots and defected ground structure (DGS) for operation over millimeter-wave and terahertz (THz) spectrum. The proposed antenna array consists of a 2 × 4 array of conductive boxes on which are implemented rectangular slots. The presence of dielectric slots introduces resonant modes within the structure. These resonant modes result in enhancing the electromagnetic fields within the slots, which radiate energy into free space. The resonant frequencies and radiation patterns depend on the specific geometry of the slots and the dielectric properties. The antenna array is excited through a single microstrip line. The radiating elements in the array are interconnected to each other with a microstrip line. Unwanted mutual coupling between the radiating elements can degrade the performance of the antenna. This was mitigated by defecting the ground plane with rectangular slots. It is shown that this technique can enhance the array’s reflection coefficient over a wider bandwidth. The array was constructed on polyimide substrate having dielectric constant of 3.5 and thickness of 20 μm. The design was modelled, and its performance verified using an industry standard electromagnetic package by CST Studio Suite. The proposed array antenna has dimensions of 20 × 10 mm2 and operates between 80 and 200 GHz for radiation gain better than 4 dBi and efficiency above 55%. The peak radiation gain and efficiency are 7.5 dBi and 75% at 91 GHz, respectively. The operational frequency range of the array corresponds to a fractional bandwidth of 85.71%.

Size Reduction and Harmonics Suppression in Microwave Power Dividers

In this paper, several types of microstrip power divider are studied and compared in terms of harmonics suppression and size reductions. The importance of this research lies in the fact that power dividers are critical components in various communication systems, and their performance directly affects the overall system efficiency. The conventional structure of the power divider has an acceptable performance at operating frequency in terms of excellent output ports isolation, low insertion loss, and high return loss, but occupies large size and passes unwanted signals at higher frequencies along with desired signal without any suppression. Harmonics are popular distortion and has different distortion impacts in many different facilities. Recently, several techniques are introduced to overcome these drawbacks. Applied open stubs, applied resonators, lumped reactive components such as capacitors and inductors, coupled lines, defected ground structure (DGS), and electronic band gaps are common methods, which are widely used to overcome these drawbacks. Finally, the study results show that the resonator-based power dividers and coupled-line-based power dividers have good performances in terms of size reduction and harmonic suppression but increase insertion loss parameter. Furthermore, the lumped reactive component-based power dividers and applied DGS and electromagnetic bandgap cells suppress unwanted harmonics, but they need extra process to fabrication, which is undesirable. Moreover, the open-stub-based power dividers have moderate performance with simple structure, but size reduction and harmonics suppression are not so superior in this method.

Design of a Circularly Polarized Micro-Strip Antenna for Aircraft Tracking Based on BeiDou III Compatible with Multi-Navigation System.

This paper proposed a right-handed circularly polarized (RHCP) micro-strip antenna for multi-navigation system applications. The size of the antenna is 70 mm × 70 mm × 2 mm, which is fabricated on an FR4 substrate. A meandering technique on a patch layer and asymmetrical defected ground structures (DGS) are employed to achieve the purpose of miniaturization and increase the bandwidth of the axial ratio. The prototype of this antenna is fabricated according to simulations where the bandwidth of return loss, bandwidth of axial ratio, and radio pattern are further testified. The bandwidth of return loss (S11) and axial ratio (AR) of the antennas are from 1.540 GHz to 1.612 GHz and 1.554 GHz to 1.601 GHz, which would be available for L1 of GPS, L1 of SBAS, E1 of Galileo as well as B1I and B1C of BDS-3, the last two of which can be used for aircraft tracking. The relative bandwidth is 2.98%, which satisfies the standard of wide-band patch antennas.

Effect of anion and methylation on the interionic interactions and reactivity of 1-butyl-2,3-dimethyl imidazolium-based ionic liquids

The study presents the investigation of anion and methylation effects on the interionic interactions, thus explaining the variations in the reactivity, electronic, and spectroscopic features in 1-butyl-2,3-dimethyl imidazolium-based ionic liquids with chloride, tetrafluoroborate, and hexafluorophosphate anions. Ground state electronic structures, IR and Raman spectra, electronic transition characteristics, and chemical shifts of the ionic liquids were obtained using DFT calculations at the B3LYP/6–311++G(d,p) level of theory. The calculated electron densities were analyzed to determine intra- and interionic interactions at critical points using Reduced Density Gradient and topological analysis through the atoms-in-molecules approach. Experimental spectroscopic characterizations were performed using the FT-IR, FT-Raman, NMR, and UV–vis techniques. These techniques and DFT calculations provide essential contributions to interpreting spectral features concerning the structure and dynamics of ionic liquids. Furthermore, molecular docking studies were performed to determine the binding status of studied ionic liquids with human serum albumin to explore their activity, thus reporting their potential due to their demand in pharmacology.

Engineering planar antenna using geometry arrangements for wireless communications and satellite applications

A triple-band microstrip patch antenna designed for the IEEE 802.16e WiMAX, IEEE 802.11a WLAN, C-band downlink communications, and Ku-band radar recent applications is suggested in this article. The planned antenna operates at 2.45, 6, and 14 GHz resonant frequencies. The antenna fulfilled triple-band physical characteristics covering industrial, scientific, and medical (ISM) bands between (2.1–2.8) GHz; (5.6–6.5) GHz for wireless local area network (WLAN) or ultra-wideband (UWB) services; and 12.7–16 GHz for future two-way 5G:6G either broadcasting or mobile satellite communications. To achieve better return loss performance, parametric studies are carried out using Microwave Studio (CST MWS). The proposed antenna is designed on the FR4 as a hosting medium of total size 46 × 38 × 1.6 mm3, combined with a planar transmission line (T.L.) feed and defected ground structure (DGS). The simulated antenna’s input reflection coefficient (S11) results and the far-field measurements show good agreement. The fabricated prototype achieves peak gain values of 2.8, 3.8, and 4.7 dBi, respectively, and bidirectional radiation characteristics. A comparative study with other recent publications is implemented to validate the consistency of the design.

Application of Gradient-Dependent Optimal Interpolation in Fishery Analysis of Neon Flying Squid (Ommastrephes bartramii) in the Kuroshio–Oyashio Confluence Region

A key issue in fishery forecasting is the collection of high-precision subsurface environmental data. A data assimilation method, named gradient-dependent optimal interpolation, was used to construct the near-real-time vertical temperature and salinity structure of a squid fishery ground based on Argo observations. The results were verified by truth-finding comparisons and applied to analyze the relationship between neon flying squid and the subsurface environment in the Kuroshio–Oyashio Confluence Region. The temperature and salinity differences between the constructed results and survey data were less than ±0.5 °C and ±0.02, respectively. Most of the relative analysis errors were less than the observational errors. Statistical analysis revealed that the most suitable temperature for squid was 18–24 °C at the near-surface (<5 m), although the squid can endure a temperature range from 11 to 12 °C at a depth of 300 m. There was an obvious thermocline in the fishery ground, with a thermocline depth of 65 m and a mean strength of approximately 0.10 °C/m. The regressive relationship between vertical temperature (thermocline parameters) and squid catch per unit effort (CPUE) followed the exponential (Gaussian) function. The most suitable salinity was 33.0–34.2 at depths shallower than 300 m.

Design of half circular wideband antenna for ship radar

The research aims to design a wideband antenna for the ship's radar. The ship's radar works on the S-Band range whose wavelengths range from 8 to 15 cm with a frequency of 2-4 GHz, This antenna design uses a new approach involving the use of Defected Ground Structure (DGS) and Defected Microstrip Structure (DMS), which builds on the initial theory. The results of the study obtained a bandwidth value of 1.6 GHz, an impedance antenna value of 49.7 ohms, with a total efficiency of -0.3356 a working frequency range ranging from 1.74 GHz to 3.3 GHz. The radiation pattern obtained the main lobe magnitude value of 3.85 dBi, Main lobe direction of 162.0 deg, angular width (3dB) of 76.7 deg, and side lobe level of -1.1 dB. From the results of working frequency, it is found that the antenna can be used for airborne warning & control (AWACS), remote sensing, WiFi, Bluetooth, mobile communication, XM radio, airport surveillance radar (ASR), radioastronomy, wireless LAN, ZigBee, missile guidance.

Hexagonal Microstrip Patch Antenna with Defective Ground Structure for Wideband Applications

The complexity and variety of modern wireless communication devices have resulted in an increase in the need for high-performance and wideband antennas. This research proposes an innovative approach for enhancing the bandwidth of hexagonal patch antennas using a microstrip line feed and the Defected Ground Structure (DGS) technology. The area of the hexagonal patch with defective ground structure wideband antenna is 32×24 mm2. The wideband ability and compact dimensions of the hexagonal patch antenna make it attractive. The DGS approach is used to change the resonant behavior of the antenna, resulting in a significant bandwidth enhancement. The simulation results demonstrate that combining DGS with the microstrip feed leads to significant enhancements in gain, radiation characteristics, and impedance bandwidth. The approach has potential for a range of wireless communication applications that demand wide performance in a compact antenna design.

Numerical investigations on the dynamic responses of metro tunnel-soil-ground building under oblique incidence of seismic wave

With the development of urban rail transits, the metro tunnels frequently underpass the above-ground buildings, and understanding the dynamic responses of metro tunnel-soil-ground buildings experiencing oblique incidence of seismic waves is of crucial importance. Considering that the seismic waves in the near-field seismic area are mostly obliquely incident to the ground at a certain angle, a two-dimensional numerical model for tunnel-soil interaction system and tunnel-soil-above ground structure was established by Abaqus software, in which the viscoelastic boundary and equivalent nodal forces were adopted to simulate the ground motion. The effects of tunnel burial depth, tunnel spacing, and tunnel frame spacing on the seismic responses of metro tunnel-soil and metro tunnel-soil-above ground building were analyzed under oblique incidence of SV wave with different incident angles. It was found that the tunnel depth has a significant effect on the lining dynamic bending moment and axial force peak, and its influence is closely related to the site category. The tunnel spacing has a minor impact on the dynamic response of the lining structure. The incident angle has a significant effect on the peak value of the dynamic shaft force of the lining. The application of the frame on the ground has a significant impact on the tunnel. The influence of above-ground buildings and tunnel burial depth should be considered when tunnel design is carried out.

Updating model parameters and predictions in SEM tunnelling using a surrogate-based Bayesian approach

This paper presents a surrogate-based Bayesian approach for updating the ground parameters within an application of the observational method in sequential excavation method (SEM) construction. A three-dimensional (3D) finite-difference model is used in the forward analysis to simulate SEM construction explicitly considering 3D multi-face excavation effects and ground–structure interaction. The polynomial-chaos Kriging (PCK) method was employed to provide a surrogate for the 3D finite-difference model to alleviate the cost of probabilistic analysis. The uncertain geotechnical parameters are updated during SEM construction through a progressive Bayesian updating procedure. Time-series observations of multiple types of measurements are used to form the likelihood function. The posterior distributions of the uncertain parameters are derived from the affine invariant ensemble sampling (AIES) algorithm. The proposed framework is illustrated through application to data from the Regional Connector Transit Corridor (RCTC) crossover cavern project constructed in downtown Los Angeles. The uncertainties of the geotechnical parameters were substantially reduced. The posterior estimations indicate higher elastic modulus and cohesion of the Fernando formation than what was assumed before the construction. The updated predictions of the ground surface, subsurface and structural deformations showed improvement in agreement with the field measurements through the continuous updating process.

A low loss microstrip line on thin flexible substrate film by defected ground structure

A low loss microstrip line on thin flexible substrate film by defected ground structure

Design and Fabrication of a 2-Port Multiple Antenna System for mmWave Application

The next-generation wireless communication technology heading towards the mmWave band requires multiple antenna systems to achieve high diversity, high data rates, and reliability. The design of multiple antenna systems is always associated with the problem of mutual coupling between antenna elements. In order to achieve better system performance, the mutual coupling between the elements has to be minimized. This work basically aims to minimize the mutual interaction among the antenna elements. A 2-port multiple antenna system is presented, with the defected ground structure as a decoupling technique, in order to minimize the mutual coupling. The single microstrip patch antenna is initially designed to operate at 24 GHz; later, it is transformed into a 2-port multiple antenna system. The transformed 2-port multiple antenna is loaded with the defective ground structure. The designed antenna system is fabricated, and practical measurements are carried out. The isolation achieved with defective ground structure through simulation is −27dB, and the practical measured value is −40dB. The 2-port multiple antenna system performance is assessed through the following metrics: Envelope Correlation Coefficient(ECC), Diversity Gain(DG), and Channel Capacity Loss(CCL). For the proposed 2-port multiple antenna the obtained values of ECC, DG and CLL are 0.004, 9.99dB and 0.4 bit/s/Hz. The results of the simulated structure are in good agreement with the fabricated structure. The result shows that defective ground is the better technique to achieve isolation between the closely placed antennas. The defective ground structure is the simplest technique in comparison with other techniques, such as metamaterial, energy band gap etc. The major novelty of the work includes, the design of a 2-port multiple antenna system with single slot and achieving the isolation more than −47dB without affecting the antenna resonating frequency.

Second- and Third-Harmonic Backscatter Through a Bandstop Filter Using Defected Ground Structure

In this brief, a novel harmonic-backscatter-rectifier (HBR) is introduced for simultaneous rectification and harmonic-based uplink. The proposed (HBR) employs a rectifier to generate both DC power and the harmonic carriers for backscattering communication, and a dual-band reconfigurable band-stop filter using defected ground structure (DGS) to modulate the second and third harmonics with low-power consumption and same input impedance at f0 all the time. As a proof of concept, an HBR prototype operating at 1.85 GHz was designed and experimented. An uplink data rate of 8 Mbps (4 Mbps × 2) was achieved when the HBR was fed with -10 dBm RF power, and the data modulation consumed less than 27.7 pJ/bit. In addition, a passive harmonic tag was implemented with the proposed HBR and a low-power binary sequence generator, which demonstrated a continuous uplink of 12 kbps at -6 dBm RF power.

High Isolation Wideband MIMO Antenna without Decoupling Technique for IoT Applications

This paper presents a method a high isolation wideband MIMO antenna without using any decoupling technique. This is achieved by transforming a strip line to a 1 ×2 MIMO antenna using Hilbert transform and Defected Ground structure is used in the antenna to resonate the antenna in for IOT and 5G sub-6 GHz bands. The proposed antenna has a size of 50 × 49.8 × 1.6 mm 3 and operates in the frequency band of 4.6 GHz to 5.94 GHz. The antenna simulated in ANSYS HFSS showed that its parameters Envelope correlation coefficient (ECC), Total Active Reflection Coefficient (TARC), Diversity gain (DG) and Channel Capacity Loss (CCL) are less than 0.04, -25 dB, 9.98 to 10 dB and less than 0.4 bits/s/Hz respectively. The radiation pattern of the antenna in both E-plane and H-plane has been simulated which the uniform distribution of power in the space.

Design of novel highly sensitive sensors for crack detection in metal surfaces: theoretical foundation and experimental validation

The application of different types of microwave resonators for sensing cracks in metallic structures has been subject of many studies. While most studies have been focused on improving the sensitivity of planar crack sensors, the theoretical foundation of the topic has not been treated in much detail. The major objective of this study is to perform an exhaustive study of the principles and theoretical foundations for crack sensing based on planar microwave resonators, especially defective ground structures (DGS) including complementary split ring resonators (CSRRs). The analysis is carried out from the equivalent circuit model as well as the electromagnetic (EM) field perspectives, and guidelines for the design of crack sensors with high sensitivity are developed. Numerical and experimental validation of the provided theoretical analysis is another aim of this article. With this aim, the developed guidelines are used to design a crack sensor based on a single-ring CSRR. It is shown that the sensitivity of the proposed sensor is almost three times higher than the sensitivity of a conventional double-ring CSRR. Moreover, it is demonstrated that folded dumbbell-shape DGS resonators can be used to achieve even higher sensitivities. The CSRR-based crack sensors presented in this study and other studies available in the literature are only sensitive to cracks with a specific orientation. To address this limitation, a modified version of the DGS is proposed to sense cracks with arbitrary orientations at the cost of lower sensitivity. The performance of all the presented sensors is validated through EM simulation, equivalent circuit model extraction, and measurement of the fabricated prototypes.

Wideband and Highly Selective BandPass Filter Using Substrate Integrated Waveguide Technology for Ku-Band Applications

A new compact design of bandpass filter using substrate integrated waveguide (SIW) is proposed and analyzed in this paper. It offers good in-band return loss, low insertion loss, wide passband, and high stopband attenuation. The filtering response is achieved by loading a couple of inverted tuning fork-shaped defected ground structures (DGS) on the bottom of the SIW cavity. DGS is utilized to enhance the upper stopband performance. To validate, the filter is fabricated using Rogers RT/Duroid 5880 with 0.508 mm thickness and tested. The filter has a center frequency of 15.44 GHz with 19% fractional bandwidth (FBW). The return loss is more than 20 dB and the insertion loss is about 1.2 dB. It finds its application in Ku band satellite communication.

A System for Monitoring and Normative Qualification of Building Structure Vibrations Induced by Nearby Construction Works

Mechanical action can damage physical objects, such as building structures. The transfer of energy to the ground through the falling mass, forming a crater, can cause kinematic forces in the soil medium. An effect of these forces, connected with the technology of geotechnical machines, is vibrations of the ground and building structures. When finding the energy impact on the object is difficult or even impossible, vibration monitoring and indirect estimation of the negative energy impact effects is possible. Commercial off-the-shelf solutions exist for vibration monitoring and recording, but they are dedicated to one application type and are relatively expensive. This paper presents a proprietary system for monitoring and recording vibrations of building objects transmitted through the ground. This allows for local registration and remote administration and presentation of data via a computer network. Vibrations can be analysed according to the requirements of developers and clients. The developed system shows that creating an effective approach for collecting data on building vibrations using components from different suppliers is possible. The waveforms collected using the system confirm the effectiveness and flexibility of the presented solution, providing a possibility of using the results to decide whether the vibrations are within the standard limits.