Graphene-based Absorber Research Articles

Single/Multi-band graphene-based disk THz absorbers with single graphene layer: conceptual design

Single/Multi-band graphene-based disk THz absorbers with single graphene layer: conceptual design

Graphene pixel based broadband polarization insensitive THz absorber

Abstract Suppressing undesired radiation and eliminating stray radiation in a high-frequency circuit might be challenging. Ultra-high frequency (UHF) electromagnetic wave absorbers are finding new applications in both the military and civilian domains. Obtaining an ultra-wide absorption band in a thin, single-layer Terahertz absorber becomes difficult. Also, achieving perfect absorption bandwidth on transverse electric (TE) and transverse magnetic (TM) mode is very sensitive. This paper presents a polarization-independent graphene-based absorbers with a near unity absorption band of 2.32 THz and 3.78 THz in a lower mid-infrared regime. The structure’s unit cell consists of cross-slot circular patches with Au as a ground separated by SiO2. To improve the absorption band another graphene layer was placed between the top and dielectric material. The absorber is polarization independent under normal incidence because of the deposited graphene structure’s fourfold symmetry. Both TE and TM polarizations were investigated, with wide-band absorption observed up to 60° incident angles in both cases. In terms of the lowest frequency of absorption, the prototype is deemed to be as thin as ∼ 0.1 λ max for both absorbers. Similarly, the effective homogeneity criteria in the subwavelength region are supported by the unit cell’s period of ∼ 0.1 λ max . The proposed absorber-2 shows 10 % higher FBW than existing work.

Dynamic tunable triple-band terahertz perfect absorber based on graphene metamaterial

This work developed a graphene-based perfect absorber with dynamic tuning capabilities. This absorber consists of a metal substrate, a layer of graphene square rings, a layer of graphene disks, and two layers of SiO2 dielectric sandwiched between them. Simulation results demonstrate absorption peaks at 1.23 THz, 4.2 THz, and 6.38 THz, with respective absorption rates of 99.9 %, 99.8 %, and 98.3 %. By analyzing the distributions of the electric field and surface current at the central frequencies of the three absorption peaks, the excitation mechanism of each absorption peak was discussed. It was found that by adjusting graphene's chemical potential, the absorption spectrum can be actively controlled. Furthermore, the absorber is insensitive to polarization and can sustain the stability of the absorption spectrum within an incident angle range of 0∼35°. This work has the potential to advance the research of multi-band terahertz absorbers, dynamically tunable devices, and other graphene-based photonic devices.

Metal-free ultrathin terahertz absorber with independently tunable dual narrow bands

Abstract A technique is introduced to precisely control the resonance behaviour of a metal-free graphene-based terahertz absorber by independently tuning dual resonant peaks. The proposed ultrathin absorber features a multilayer configuration, with two isolated resonator layers of patterned graphene on dielectric (SiO2) substrates, and a thin graphite sheet at the bottom serving as a reflector. The stacked arrangement enables independent tunability of the high-absorptivity resonant peaks at 7.33THz and 9.34THz. The structure, with a thickness of just λ/15 of the free-space wavelength, offers a compact design suitable for space-constrained applications. Its symmetrical geometry ensures polarization insensitivity and stable performance for incident angles up to 60°. Simulated results, analysed via CST Studio and validated with an Equivalent Circuit Model (ECM), demonstrate excellent thermal stability. Furthermore, the narrowband response of the proposed absorber improves its sensitivity for refractive index variations induced by biomolecular interactions validating its suitability in biosensing applications. The absorber demonstrates peak absorption across both the resonant frequencies with an analyte optimised at 1.5μm thickness. Sensitivity levels of 1.1THz/RIU and 1.05THz/RIU along with figure-of-merit (FOM) values of 2.11 and 2.23. are recorded for the lower and upper bands, respectively. The absorber offers enhanced selectivity owing to low values of full-width at half maximum (FWHM). High Q-factors of 12.85 and 19.3, confirm its strong potential for refractive index sensing. 

Electric-Controlled Switching ON/OFF of Bands in a Graphene-Based Multi-band Metamaterial Absorber

Electric-Controlled Switching ON/OFF of Bands in a Graphene-Based Multi-band Metamaterial Absorber

Graphene-Based Dual-Band Metasurface Absorber with High Frequency Ratio.

In this paper, we propose a novel dual-band metasurface absorber with a high frequency ratio based on graphene. By carefully designing a centrally symmetrical graphene pattern and positioning it on a glass medium, while utilizing ITO as a ground, the metasurface absorber achieves remarkable high frequency ratio microwave absorption. Specifically, this metasurface absorber exhibits two distinct resonance points at 3.7 GHz and 14 GHz, with an impressive frequency ratio over 3.5. It achieves over 90% absorption efficiency in the frequency ranges of 3.5-4.5 GHz and 13.5-14.5 GHz, highlighting its capability to effectively absorb microwaves across widely spaced frequency bands. Furthermore, the metasurface absorber demonstrates optical transparency and polarization insensitivity, adding to its versatility and potential applications. The measured results of the fabricated prototype validate its design and potential for practical use.

Metasurface Absorber for Blood Hemoglobin Concentration.

In this study, a biosensing scenario is developed for monitoring blood quality based on the detection of blood hemoglobin concentration. The procedure involves considering the blood sample as the dielectric with different refractive indexes for different concentrations of hemoglobin. Usually, the sensitivity to design parameters is the major issue with the metasurface-based detection. To address this issue, a three-layer graphene-based wave absorber is designed and modeled using passive circuit elements. The major idea behind this work is to maximize the device sensitivity against the blood sample. The research methodology involves impedance matching between the device and the surrounding environment, while full-wave simulation is also performed and compared to ensure circuit view accuracy. The findings suggest that the proposed graphene-based absorber can efficiently monitor blood quality via dual absorption peaks. The simulation results extracted from impedance matching and the full-wave method indicate frequency shifts of the second absorption peak. These shift values are interpreted based on hemoglobin concentration. Additionally, ample analyses are provided to show the reliability of the proposed absorber against geometrical aspects, incident angle, external stimulation, and the graphene electron relaxation time.

Graphene-based metamaterial ultrawideband absorber with enhanced terahertz performance

In this paper, we present a graphene-based metamaterial ultrawideband absorber operating in the terahertz regime. The absorber is composed of two patterned and continuous graphene layers, a bottom gold layer, and a SiO2 substrate that separates the continuous graphene layer from the gold layer. The absorption spectrum is enhanced by integrating a graphene resonator with water, which has frequency-dependent permittivity. The water is encapsulated in polytetrafluoroethylene (PTFE) in the form of a circular ring sandwiched between the two graphene layers. Simulation results show that the absorber attains a 90 % absorption bandwidth of about 14.55 THz. The proposed absorber is polarization-insensitive under normal incidence. For TE polarization, the absorption level remains stable for incident angles θ from 0° to 55° across the entire frequency band (14.55 THz), except for the 5–8 THz range. For TM polarization, the absorption level remains stable for θ ranging from 0° to 60° over the entire bandwidth. Additionally, the absorption level is consistent for both TM and TE polarizations across the entire bandwidth for incident angles φ from 0° to 90°.

Retraction Note: A graphene-based triple-band THz metamaterial absorber for cancer early detection

Retraction Note: A graphene-based triple-band THz metamaterial absorber for cancer early detection

Graphene/carbon nanotube aerogels with ultralow filling ratio through perfect cross-linking interface for efficient microwave absorption

Utilizing high-efficiency electrostatic assembly and a scalable freeze-drying technique followed by carbonization, we have developed a series of unique, lightweight, hierarchically porous 1D+2D aerogels containing carbon nanotubes (CNTs) and reduced graphene oxide (rGO). By manipulating the interaction between CNTs and graphene oxide perjurer in cellulose nanofiber (CNF), CNTs can uniformly distribute along the graphene cell walls via an exceptional cross-linking interface in the resultant rGO/CNT aerogels. This arrangement enables abundant heterogeneous interfaces, endowing the aerogels with high conductivity and polarization loss capacity. Moreover, the 1D+2D microstructure of CNT/rGO and the hierarchical pore architecture of the aerogels facilitate multiple scattering, further enhancing their loss capacity toward electromagnetic wave absorption (EMW). Coupled with the optimized impedance matching derived from the adjustable dielectric properties, the aerogels exhibit outstanding EMW absorption with a filling ratio of merely 2 wt%. Specifically, a minimum reflection loss (RLmin) of −49.61 dB and an effective absorption bandwidth (EAB) of 4.16 GHz are achieved. With a filling ratio of 3 wt%, the RLmin reaches −77.51 dB, accompanied by an EAB of 3.84 GHz, surpassing the reported carbon or graphene-based aerogel EMW absorbers. In this work, the ultra-low filling ratio resulting from high conductivity confers a practical design for fabricating lightweight carbon-based aerogels suitable for high-efficiency EMW absorption, manifesting multiple applications in electromagnetic compatibility and aerospace contexts.

Polarization-selective terahertz absorber based on square cyclic graphene surface

Graphene-based absorbers are highly valued in terahertz technology due to their efficient performance. In this study, we theoretically propose a tunable, high sensitivity, single-band terahertz perfect absorber with polarization coherence that exhibits stable performance across a broad range of incidence angles. Simulation results show that the absorber's sensitivity to both TM and TE waves can be maintained at about 2 THz/RIU, with optimal values above 13.3 RIU−1 for TM waves and 12.9 RIU−1 for TE waves, and all Q-factors above 52. Furthermore, the impedance matching approach is utilized to explain the mechanism underlying its efficient absorption, and the electric field distribution is used to analyze the polarization coherence phenomena. We also propose a polarization-insensitive hetero-geometric structure based on the original structure, which allows for the separation of the absorption peaks by adjusting the geometrical parameters. These results show that the structure has a wide range of applications in aerospace, communication engineering, and image processing.

Engineering multifunctionality graphene-based nanocomposites with epoxy-silane functionalized cardanol for next-generation microwave absorber

As technology advances, the demand for effective microwave-absorbing materials (MAM) to mitigate electromagnetic wave interference is growing. Two-dimensional (2D) materials are increasingly favored across various fields for their high specific surface area, electrical conductivity, low density, and dielectric loss properties. This study presents lightweight nanocomposites composed of graphene nanoplatelets blended with epoxy resin (ER) and cardanol with silane-functionalized (SFC) as a toughening agent. The resulting nanocomposites exhibit a high surface roughness of 130 nm and an enhanced hydrophobicity, as evidenced by a high contact angle. Notably, the ER/SFC/GNP sample at 3 wt% (0.075 g) achieves a minimum reflection loss value of −18 dB at a thickness of 10 mm, indicating improved impedance matching and enhanced dielectric loss capability. The increasing damping factor ratio to approximately 0.95 further augments the reflection loss performance. The research aims to develop cost-effective, efficient, lightweight graphene-based nanocomposite absorbers.

Graphene-based tunable broadband metamaterial absorber for terahertz waves

In order to overcome the limitations exhibited by traditional absorbers in electromagnetic wave absorption, such as the extremely narrow absorption bandwidth and uncontrollable absorption results, this paper proposes a novel tunable broadband metamaterial absorber based on graphene. Compared to other terahertz absorbers, the absorber designed in this study exhibits simpler structural design, compact form, thin thickness, efficient absorption performance, and a broader bandwidth. This absorber adopts a three-layer structure, including a patterned monolayer graphene metasurface, a dielectric layer, and a metal substrate. The structure of this patterned graphene consists of four triangular graphene resonators, achieving both high absorption efficiency and maintaining an exceptionally wide absorption bandwidth. The simulation results indicate that at a Fermi energy level Ef of 0.45 eV, the absorber achieves a broadband absorption rate of over 90 % in the 3.287 THz to 5.247 THz frequency range under normal terahertz wave incidence conditions. By analyzing different quantities of the triangular graphene structure on the top of the absorber, we found that the wide absorption bandwidth of the absorber is mainly attributed to the structural coupling of the top-layer graphene in the absorber. Furthermore, through the study of electric field amplitude and current distribution, we stumbled upon that when terahertz waves are incident on the absorber, due to the structural coupling between the graphene layers, electric resonance and magnetic resonance occur within the absorber, resulting in the absorption effect. Finally, through the study of geometric parameters, different polarization angles and oblique incidence angles of the incident waves, as well as different Fermi energy levels of graphene, we discovered that by adjusting the Fermi energy level of graphene, the bandwidth and absorption performance of the absorber can be flexibly tuned. In addition, this absorber exhibits wide-angle absorption characteristics and polarization-insensitive properties, providing potential application prospects in fields such as terahertz thermal imaging and stealth technology.

Graphene-based polarization insensitive structure of ultra-wideband terahertz wave absorber

Graphene, a new smart material, has gained a lot of attention recently because of its tunable band structure and strong light-matter interaction. In comparison with typical absorbers, graphene absorbers have emerged as a highly attractive substitute for various types of applications. To broaden the absorption bandwidth, a two-dimensional graphene-based ultra-wideband and polarization-insensitive novel terahertz (THz) absorber with absorption over 95 % from 3.0 THz to 8.5 THz is proposed, with peak absorption of 99.9 % at 6.6 THz and average absorption of 98.4 % for the 5.5 THz bandwidth. The surface plasmon increased by the gold-graphene structure, the Mei resonance, and the interference cancellation between metasurfaces collectively contribute to the ultra-wideband absorption. To obtain nearly perfect broadband terahertz absorption, a single layer of graphene is used. The finite difference time domain (FDTD) approach is used for absorber analysis. In addition, the absorber is insensitive to the polarization angles and incidence angles of incident electromagnetic waves. The proposed graphene-based absorber dominates previously reported wideband THz absorbers in terms of over 95 % bandwidth, absorption peak value, and overall volume. This research will present a novel idea for the design of an ultra-wideband absorber, which can be considered a suitable candidate for different potential applications in terahertz imaging, sensors, photodetectors, and modulators.

Graphene-based Multilayer Surface Plasmon Resonance Solar Absorber in the UV to MIR Region for Renewable Energy Application

Graphene-based Multilayer Surface Plasmon Resonance Solar Absorber in the UV to MIR Region for Renewable Energy Application

Switchable THz wave absorber based on disks and its complement graphene surfaces

A new geometrical vision for a graphene-based THz wave absorber is investigated in this work. A high-performance THz absorber is proposed to exploit complementary conventional periodic arrays of graphene disks. The equivalent circuit model is modified to take account of the complement pattern. The absorber works in two different operational modes based on chemical potential values. One mode shows absorption around 1 THz while the other one expresses perfect absorption at 6 THz and 9 THz. Such a considerable shifting ability via gate stimulations makes the proposed absorber an ideal block for reconfigurable metasurface. The comparison between the circuit model and full-wave simulation verifies an excellent match while ample sensitivity analysis are reported to show the reliability of the proposed switchable THz absorber.

Polarization-insensitive graphene-based band-notched frequency selective absorber at terahertz

This paper introduces a new polarization-insensitive graphene-based frequency selective absorber (FSA) with a reflective notch designed for terahertz applications. The proposed structure features two absorption bands on either side of a central reflection band. The design composes a lossy frequency selective surface (FSS), a bandstop FSS with a metal backing, and an air spacer between. A wideband absorber structure is developed in the first step, leveraging graphene as an absorbent material in the lossy layer to achieve wideband absorptive characteristics. Subsequently, a reflection band is introduced by integrating a bandstop, lossless FSS layer into the absorber structure. The overall structure demonstrates two distinct absorption bands, characterized by absorptivity exceeding 80% within the frequency ranges of 0.30 to 0.57 and 0.67 to 0.90 THz. Simultaneously, a reflection notch is achieved at 0.60 THz. Extensive simulations assessed the performance of the designed FSA. The proposed structure exhibits stability under oblique incidence up to 40 deg and allows tunable absorption specifications by adjusting the chemical potential of graphene. It is noteworthy that the FSA reflector offers advantages such as eliminating the need for complicated, high-cost 3-D structures and welding of the lumped resistors.

Solar thermal applications of graphene-based block-ring resonator solar absorber using TiC–W materials

Solar absorbers enable the use of solar energy, a renewable and plentiful resource, minimizing reliance on finite fossil fuels and contributing to sustainable energy practices. The solar absorber that is studied here has an average absorptance of 96.85 % with a simple design and inexpensive materials. This design has two layers of resonator and active layer Block Ring Base Solar Absorber (BRBSA) structure. This study employs tungsten (W) as a resonator and titanium carbide (TiC) as a dielectric layer. The absorption spans from 100 to 3200 nm, with an average absorption exceeding 94 % across the entire structure. Notably, over 97 % of absorption occurs within the range of 210–710 nm, and the highest absorption, reaching 99.9 %, is observed in the wavelength range of 1510–1650 nm. The structure demonstrates high absorption rates across various regions, including 95.85 % in the UV region, 97.89 % in the visible, 95.73 % in the near-infrared, 95.87 % in the mid-infrared, and 89.56 % in the far-infrared region. After analyzing various potential variations of the proposed structure, an optimal design was identified. The parametric study was conducted to determine the optimal physical properties. Additionally, the electric field intensity analysis confirmed the proposed structure's broadband and constant absorption response. This Block Ring Base Solar Absorber has various uses, including solar drying systems, cookers, vaporizers, and warmers.

Graphene-Based Metamaterial Absorber with Perfect Multi-band Absorption

Graphene-Based Metamaterial Absorber with Perfect Multi-band Absorption

Wideband low-RCS and gain-enhanced antenna using frequency selective absorber based on patterned graphene

In this paper, a double-layer patterned graphene-based frequency-selective absorber (DGFSA) is proposed as a means of reducing an antenna’s radar cross-section (RCS) while simultaneously increasing its gain. The antenna consists of a patch antenna with Multi-Graphene Frequency Selective Absorber (MGFSA) mounted on top. The DGFSA consists of double-layer patterned graphene and a band-pass frequency selective surface (FSS). Two patterned graphene lossy layers with different square resistances are used, which broaden the electromagnetic (EM) wave absorption bandwidth of the DGFSA, thus greatly reducing the out-band monostatic RCSs of the patch antenna. Meanwhile, due to the quasi-Fabry-Perot (F-P) effect, the gain of the proposed antenna is enhanced by 2.4 dB. Additionally, the low-RCS antenna reduces the monostatic RCS from 1.32 to 17 GHz under y-polarization and from 1.4 to 16.8 GHz under x-polarization, respectively. Furthermore, a decrease in the bistatic RCS is accomplished. Results from simulations and measurements match up nicely, which means the antenna we proposed has a good application on the stealth platform.