Good Mechanical Properties Research Articles

Multi-pass butt welding of thick TA5 titanium-alloy plates by MIG: Microstructure and Properties

A 35 mm-thick sheet of TA5 titanium alloy was successfully joined by metal inert-gas (MIG) welding. The welded joints were analyzed in a more integrated and comprehensive manner. The joint microstructure was analyzed by OM, SEM, EBSD, and TEM. Mechanical properties were analyzed by tensile, impact, and microhardness tests. The corrosion resistance of the joints was determined by FeCl3 immersion corrosion. Experimental results showed that the mechanical properties and corrosion resistance of the fusion zone (FZ) were poorer than those of the base material (BM). The mechanical properties of the welded joints were related to the acicular grains in the FZ. The 260A joints showed relatively good mechanical properties. With increased welding current, the proportion and size of the acicular grains increased, and the strength of the joint increased, but the plastic toughness decreased. When the welding current was too small, anisotropy occurred in the FZmiddle, which affected the mechanical properties of the joints. The corrosion resistance of the FZ was lower than that of the BM, and the corrosion resistance of the three groups of joints decreased in the order 300A > 230A > 260A.The welding current affected the corrosion resistance of the FZ by influencing the grain size of the FZ, the frequency of the HAGBs, and the GND density.

Layer effects on MXenes electrode and it applied to silicon composite structures

Despite the very high capacity of Si (4200mAh g−1), the widespread application of Si anodes has been hampered by drastic volume changes (up to 300 %) during cycling, leading to electrical contact losses and thus a sharp drop in capacity as the cycle life is shortened. Here we present a class of layered MXene/Si electrodes, which consist of nano-Si embedded in the interlayers of MXene to form a coupling effect, which can inhibit the huge volume change of Si during cycling. Therefore, layered MXene/Si has a highly reversible capacity, much improved cycling performance and excellent mechanical properties. First-principles calculations reveal the excellent electronic conductivity and good diffusion ability of layered MXene/Si, confirming the rapid storage of Li ions. This study provides useful information for the development and production of anode materials with high energy density and good mechanical properties.

Https://epg.science.cmu.ac.th/ejournal/journal-detail.php?id=11813

In this study, waste magnesite (WM) particles with different weight fractions (2.5%, 5%, and 7.5%) were used as particulate material in 6061 aluminium alloy to produce composites with improved properties. The composite material was manufactured using a stir-casting method. A surface morphology investigation confirms the uniform distribution and good interfacial bonding of the WM particles within the alloy base. The addition of 5% WM particles was found to improve the values of tensile strength of 146.68 MPa, hardness of 131.6 HV and coefficient of friction of 0.565. Incorporating 7.5% WM was found to give a low wear of 161 μm and a corrosion current of 8.5 x 10-6 A. The results obtained confirm that such a proportion of WM particles in Al 6061 alloy provides excellent anticorrosion protection, wear properties, and good mechanical properties. Adding 5% WM to Al 6061 improves overall performance characteristics among other ratios.

Experimental Simulation of Directional Crystallization of SiMo Cast Iron Alloyed with Al and Cr

SiMo ductile cast iron combines ease of part fabrication with good mechanical properties, including a usable plasticity range. Its poor corrosion resistance inherited from grey cast iron could be alleviated through alloying with Al or Cr additions capable of forming a dense oxide scale protecting the substrate. However, the presence of Al and Cr in cast iron tends to make the material brittle, and their optimum alloying additions need to be studied further. The present work was aimed at investigating the effect of crystallization rates on microstructure changes during directional crystallization of SiMo-type alloys with up to 3.5% Al and 2.4% Cr. The experiment was performed using the Bridgman–Stockbarger method. The tubular crucible was transferred from the hot section to cold section at rates ranging from 5 mm/h to 30 mm/h with a 4/5 crucible length and then quenched. The introduced Al promoted graphitization up to a point, wherein, at the highest applied addition, the graphite precipitation preceded crystallization of the rest of the melt. A rising level of Cr in these alloys from 1% to 2.4% resulted in the formation of low and high contents of pearlite, respectively. The higher crystallization rates proved effective in increasing the ferrite content at the expense of pearlite. In the investigated cast iron samples with smaller applied alloying additions, Widmanstätten ferrite or ausferrite, i.e., fine acircular phase, were often found. The switch from directional crystallization to quenching caused a transition from a liquid to solid state, which started with nucleation of islands of fine austenite dendrites with chunky graphite eutectic separating them. As these islands expanded, they pushed alloying additions to their sides, promoting carbide or pearlite formation in these places and forming a super-cell-like structure. The performed experiments helped gather information concerning the sensitivity of the microstructure of SiMo cast iron modified with Al and Cr to crystallization rates prevailing in heavy cast structures.

A Comparative Analysis of Low and High SiC Volume Fraction Additively Manufactured SiC/Ti6Al4V(ELI) Composites Based on the Best Process Parameters of Laser Power, Scanning Speed and Hatch Distance

Silicon carbide (SiC) exhibits intriguing thermo-physical properties such as higher heat capacity and conductivity, as well as a lower density than Ti6Al4V(ELI). These properties make SiC a good candidate for the reinforcement of Ti6Al4V(ELI) with respect to its use as a heat shield in aero turbines to increase their efficiency. The traditional materials used in aircraft structures were required to have a combination of good mechanical properties such as strength, stiffness, and hardness and low weight, as well as low thermo-physical properties such as coefficient of thermal expansion (CTE) and thermal conductivity. The alloy Ti6Al4V(ELI) has a density of 4.45 g/cm3, which is lower than that of structural steel (7.4 g/cm3) and higher than that of aluminium (2.5 g/cm3). Lower density benefits light weighting. Aluminium is the lightest of the traditional materials used but has relatively low strength. The CTE of SiC of 4.6 × 10−6/K is lower than that of Ti6Al4V(ELI) of 8.6 × 10−6/K, while the density of SiC of 3.21 g/cm3 is lower than that of Ti6Al4V(ELI) of 4.45 g/cm3. Therefore, from the theory of composites, SiC/Ti6Al4V(ELI) composites are expected to have lower densities and CTEs than those of Ti6Al4V(ELI), thus providing for lightweighting and less thermal related buckling or separation at their joints with carbon/epoxy resin panels. The specific strength, stiffness, and Knoop hardness of SiC of 75–490 kNm/kg, 132 MNm/kg, and 600–3800 GPa, respectively, are generally larger than those of Ti6Al4V(ELI) of 211 KNm/kg, 24 MNm/kg, and 880 GPa, respectively. Therefore, investigating reinforcement of Ti6Al4V(ELI) with SiC particles is worthwhile as it will lead to the formation of composites that are stronger, stiffer, harder, and lighter, with lower values of CTE. For additive manufacturing, this requires initial studies to optimise the process parameters of laser power and scanning speed for single tracks. To print single tracks in the present work, different laser powers ranging from 100 W to 350 W and scanning speeds ranging from 0.3 m/s to 2.7 m/s were used for different SiC volume fraction values of values. To print single layers, different values of hatch distance were used together with the best values of laser power and scanning speed determined elsewhere by the authors for different volume fractions of SiC. Through optical microscopy, the built tracks and their cross sections were examined. By using laser power and scanning speeds of 200 W and 1.2 m/s, and 150 W and 0.8 m/s, respectively, the best tracks at 5% and 10% volume fractions were obtained, whereas the best tracks at 25% volume fraction were achieved using a laser power of 200 W and a scanning speed of 0.5 m/s. Furthermore, the results showed that the maximum SiC volume percentage of 30% resulted in limited or no penetration. Therefore, it is concluded from the study that parts with improved mechanical properties can be produced at SiC volume fractions ranging from 5% to 25%, while parts produced at the high volume fraction of 30 % would have unacceptable mechanical qualities for the final part.

Bottom-up Assembling Hierarchical Enamel-like Bulk Materials with Excellent Optical and Mechanical Properties for Tooth Restoration.

Enamel has good optical and mechanical properties because of its multiscale hierarchical structure. Biomimetic construction of enamel-like 3D bulk materials at nano-, micro-, mesh- and macro-levels is a challenge. We reported a novel facile, cost-effective, and easy large-scale bottom-up assembly strategy to align 1D hydroxyapatite (HA) nanowires bundles to 3D hierarchical enamel structure with the nanowires bundles layer-by-layer interweaving orientation. In the strategy, the surface of oleate templated ultralong HA nanowires with a large aspect ratio was functionalized with amphiphilic 10-methacryloyloxydecyl dihydrogen phosphate (MDP). Furtherly, the MDP functionalized HA nanowire bundles were assembled layer-by-layer with oriented fibers in a single layer and cross-locked between layers at a certain angle at mesoscale and macroscale in the viscous bisphenol A-glycidyl methacrylate (Bis-GMA) ethanol solution by shear force induced by simple agitation and high-speed centrifugation. Finally, the excessive Bis-GMA and ethanol were removed, and (Bis-GMA)-(MDP-HA nanowire bundle) matrix was densely packed under hot pressing and polymerized to form bulk enamel-like materials. The composite has superior optical properties and comparable comprehensive mechanic performances through a combination of strength, hardness, toughness, and friction. This method may open new avenues for precisely controlling the nanowires assembly to develop hierarchical nanomaterials with superior properties for many different applications. This article is protected by copyright. All rights reserved.

SUPERHYDROPHOBIC ALL-CELLULOSE COMPOSITE VIA HEXADECYLTRIMETHOXYSILANE AND HDTMS/SILICA

All-cellulose composite (ACC) is a novel single polymer composite (SPC) that consists of cellulose for both reinforcing fiber and matrix phases. ACC has good mechanical, thermal, and optical properties due to compatibility of reinforcing fiber and matrix phases. However, abundant hydroxyl (OH) groups in the cellulose structures resulted in higher hydrophilicity of ACC, thus limiting the potential use in outdoor applications. In this study, ACC was fabricated using solvent infusion processing (SIP) from rayon textile with sodium hydroxide (NaOH)/urea solution to partially dissolve the cellulose fibers, followed by regeneration and drying processes. Subsequently, ACC was treated using two different coating solutions: (i) hexadecyltrimethoxysilane (HDTMS) and (ii) HDTMS/SiO2 (silica). As a result, an efficient water repellency for HDTMS/SiO2-treated ACC was observed, showing a water contact angle of 159.3∘, as compared to HDTMS-treated ACC with a water contact angle of 144.1∘. However, a slightly higher water absorption of 52% was observed for HDTMS/SiO2-treated ACC, as compared to only 44% for HDTMS-treated ACC. Both treated ACCs showed smooth and homogeneous structures upon completion of the treatment.

An In-Depth Investigation of the Effects of Tungsten Inert Gas Welding Process Parameters on Hardness and Corrosion Resistance of 2205 DSS Weldments: New Design of Experiment Parametric Studies and Optimization

The aim of this work is to examine and analyze, using response surface methodology, how the TIG welding process parameters of welding current (WC), welding speed (WS), and N2 with argon as shielding gas affect the hardness and corrosion resistance of 2205 DSS weldments. Due to the equal amounts of ferrite and austenite phases and alloying elements, duplex stainless steel DSS offers good mechanical properties and corrosion resistance. The mechanical characteristics and resistance to corrosion of the weld zone, as well as the heat-affected zone of the DSS, are, however, disturbed as a result of the welding process since it changes the distribution of these two phases and also the alloy is thermally disturbed. Therefore, in this work, an in-depth investigation of the effects of the above-mentioned parameters on the DSS quality has been performed. Results showed that increasing welding current while decreasing welding speed, which corresponds to the highest heat input, led to lower critical pitting potential and weld zone hardness but higher heat-affected zone hardness. The same results were obtained for decreasing welding current while increasing welding speed, which correspond to the lowest heat input. However, the addition of a small percent (%) of N2 to argon shielding gas resulted in increasing the critical pitting potential and decreasing the hardness in welds and heat-affected zones. Numerically, the RSM planned experimental results showed that an optimum welding current of 175A, welding speed of 170 mm/min, and 10% N2 with argon as shielding gas maximized the critical pitting potential up to 318 mV and optimized the hardness of the weld and heat-affected zone to about base metal hardness of 288 and 286 HV, respectively.

Cention-N: A Review

An ideal material used for restoration should be adhesive, tooth coloured, resistant to wear, nontoxic and biocompatible with the tissue. Various direct filling materials are available in dentistry such as amalgam, glass ionomer cement (GIC) and esthetic composite material, each of them having its advantages and disadvantages hence proper selection of restorative materials will help for its clinical success. Cention-N is a new alkasite, bulk filling, basic tooth-coloured, radiopaque material introduced by Ivoclar Vivadent in 2016. It is a self-curing filling material with optimum light curing. It consists of an isofiller which reduces the polymerization shrinkage and utilizes an alkaline filler which is capable of releasing acid-neutralizing ions. It presents with good mechanical properties and long-term stability due to the cross-linking of methacrylates in the final restoration hence it can be used in load-bearing areas. Cention-N can be efficiently used in pediatric patients as it is moisture resistant and releases fluoride which helps in remineralizing teeth thus preventing secondary caries. The use of caution is restricted in the anterior tooth as it is available only in one shade.

A Review of Sisal Fiber-Reinforced Geopolymers: Preparation, Microstructure, and Mechanical Properties.

The early strength of geopolymers (GPs) and their composites is higher, and the hardening speed is faster than that of ordinary cementitious materials. Due to their wide source of raw materials, low energy consumption in the production process, and lower emissions of pollutants, they are considered to have the most potential to replace ordinary Portland cement. However, similar to other inorganic materials, the GPs themselves have weak flexural and tensile strength and are sensitive to micro-cracks. Improving the toughness of GP materials can be achieved by adding an appropriate amount of fiber materials into the matrix. The use of discrete staple fibers shows great potential in improving the toughness of GPs. Sisal is a natural fiber that is reproducible and easy to obtain. Due to its good mechanical properties, low cost, and low carbon energy usage, sisal fiber (SF) is a GP composite reinforcement with potential development. In this paper, the research progress on the effect of SF on the properties of GP composites in recent decades is reviewed. It mainly includes the chemical composition and physical properties of SFs, the preparation technology of sisal-reinforced geopolymers (SFRGs), the microstructure analysis of the interface of SFs and the GP matrix, and the macroscopic mechanical properties of SFRGs. The properties of SFs make them have good bonding properties with the GP matrix. The addition of SFs can improve the flexural strength and tensile strength of GP composites, and SFRGs have good engineering application prospects.

Recent Advances in Magnesium–Magnesium Oxide Nanoparticle Composites for Biomedical Applications

Magnesium (Mg) is considered an attractive option for orthopedic applications due to its density and elastic modulus close to the natural bone of the body, as well as biodegradability and good tensile strength. However, it faces serious challenges, including a high degradation rate and, as a result, a loss of mechanical properties during long periods of exposure to the biological environment. Also, among its other weaknesses, it can be mentioned that it does not deal with bacterial biofilms. It has been found that making composites by synergizing its various components can be an efficient way to improve its properties. Among metal oxide nanoparticles, magnesium oxide nanoparticles (MgO NPs) have distinct physicochemical and biological properties, including biocompatibility, biodegradability, high bioactivity, significant antibacterial properties, and good mechanical properties, which make it a good choice as a reinforcement in composites. However, the lack of comprehensive understanding of the effectiveness of Mg NPs as Mg matrix reinforcements in mechanical, corrosion, and biological fields is considered a challenge in their application. While introducing the role of MgO NPs in medical fields, this article summarizes the most important results of recent research on the mechanical, corrosion, and biological performance of Mg/MgO composites.

Porous gradient hydrogel promotes skin regeneration by angiogenesis

The skin has a multilayered structure, and deep-seated injuries are exposed to external microbial invasion and in vivo microenvironmental destabilization. Here, a bilayer bionic skin scaffold (Bilayer SF) was developed based on methacrylated sericin protein to mimic the skin’s multilayered structure and corresponding functions. The outer layer (SF@TA), which mimics the epidermal layer, was endowed with the function of resisting external bacterial and microbial invasion using a small pore structure and bio-crosslinking with tannic acid (TA). The inner layer (SF@DA@Gel), which mimics the dermal layer, was used to promote cellular growth using a large pore structure and introducing dopamine (DA) to regulate the wound microenvironment. This Bilayer SF showed good mechanical properties and structural stability, satisfactory antioxidant and promote cell proliferation and migration abilities. In vitro studies confirmed the antimicrobial properties of the outer layer and the pro-angiogenic ability of the inner layer. In vivo animal studies demonstrated that the bilayer scaffolds promoted collagen deposition, neovascularization, and marginal hair follicle formation, which might be a promising new bionic skin scaffold.

Study of Biocomposite Films Based on Cassava Starch and Microcrystalline Cellulose Derived from Cassava Pulp for Potential Medical Packaging Applications

This study aimed to develop biocomposite films based on cassava starch and microcrystalline cellulose (MCC) derived from cassava pulp for potential medical packaging applications. MCC was extracted from cassava pulp, and its structure and chemical composition, crystallinity, and thermal properties were characterized. The MCC showed a yield of 14.92% and crystallinity of 46.91%. Different MCC contents (1%, 3%, and 5% w/w of starch) were incorporated into cassava starch films. The effects of MCC contents on film properties, including morphology, thickness, mechanical strength, chemical interactions, moisture content, surface wettability, and water activity index, were studied. The effects of UV-C sterilization on the disinfection of starch/MCC on film properties were determined. Results showed that all starch/MCC films exhibited good transparency and thickness ranging from 127 to 144 µm. As MCC content increased from 1 to 5%, Young’s modulus and tensile strength of the films improved significantly from 112.12 to 488.89 MPa and 3.21 to 11.18 MPa, respectively, while elongation at break decreased from 44.74 to 4.15%. Incorporating MCC also reduced film surface wettability, with the water contact angle increasing from 69.17° to 102.82°. The starch/3%MCC holds promise as a biocomposite film for medical packaging applications, offering advantages in terms of good transparency, mechanical properties, and surface hydrophobicity. Furthermore, the absence of microbial growth in the sterilized gauze pad with sealing in the sterilized starch/3%MCC film confirms that the UV-C sterilization, 30 min for each side at 254 nm effectively eliminated any microorganisms present on the starch/3%MCC film without damaging the film properties. This finding highlights a reliable approach to ensuring the sterility of starch/MCC films for medical packaging applications.

A novel conductive microtubule hydrogel for electrical stimulation of chronic wounds based on biological electrical wires

Electrical stimulation (ES) is considered a promising therapy for chronic wounds via conductive dressing. However, the lack of a clinically suitable conductive dressing is a serious challenge. In this study, a suitable conductive biomaterial with favorable biocompatibility and conductivity was screened by means of an inherent structure derived from the body based on electrical conduction in vivo. Ions condensed around the surface of the microtubules (MTs) derived from the cell’s cytoskeleton are allowed to flow in the presence of potential differences, effectively forming a network of biological electrical wires, which is essential to the bioelectrical communication of cells. We hypothesized that MT dressing could improve chronic wound healing via the conductivity of MTs applied by ES. We first developed an MT-MAA hydrogel by a double cross-linking method using UV and calcium chloride to improve chronic wound healing by ES. In vitro studies showed good conductivity, mechanical properties, biocompatibility, and biodegradability of the MT-MAA hydrogel, as well as an elevated secretion of growth factors with enhanced cell proliferation and migration ability in response to ES. The in vivo experimental results from a full-thickness diabetic wound model revealed rapid wound closure within 7d in C57BL/6J mice, and the wound bed dressed by the MT-MAA hydrogel was shown to have promoted re-epithelization, enhanced angiogenesis, accelerated nerve growth, limited inflammation phases, and improved antibacterial effect under the ES treatment. These preclinical findings suggest that the MT-MAA hydrogel may be an ideal conductive dressing for chronic wound healing. Furthermore, biomaterials based on MTs may be also promising for treating other diseases.

Calcipotriol Nanosuspension-Loaded Trilayer Dissolving Microneedle Patches for the Treatment of Psoriasis: In Vitro Delivery and In Vivo Antipsoriatic Activity Studies.

Psoriasis, affecting 2-3% of the global population, is a chronic inflammatory skin condition without a definitive cure. Current treatments focus on managing symptoms. Recognizing the need for innovative drug delivery methods to enhance patient adherence, this study explores a new approach using calcipotriol monohydrate (CPM), a primary topical treatment for psoriasis. Despite its effectiveness, CPM's therapeutic potential is often limited by factors like the greasiness of topical applications, poor skin permeability, low skin retention, and lack of controlled delivery. To overcome these challenges, the study introduces CPM in the form of nanosuspensions (NSs), characterized by an average particle size of 211 ± 2 nm. These CPM NSs are then incorporated into a trilayer dissolving microneedle patch (MAP) made from poly(vinylpyrrolidone) and w poly(vinyl alcohol) as needle arrays and prefrom 3D printed polylactic acid backing layer. This MAP features rapidly dissolving tips and exhibits good mechanical properties and insertion capability with delivery efficiency compared to the conventional Daivonex ointment. The effectiveness of this novel MAP was tested on Sprague-Dawley rats with imiquimod-induced psoriasis, demonstrating efficacy comparable to the marketed ointment. This innovative trilayer dissolving MAP represents a promising new local delivery system for calcipotriol, potentially revolutionizing psoriasis treatment by enhancing drug delivery and patient compliance.

Fabrication of antibacterial bone scaffold based on carbonate-substituted hydroxyapatite containing magnesium from black sea urchin (Arbacia lixula) shells reinforced with polyvinyl alcohol and gelatin

Carbonate-substituted hydroxyapatite containing magnesium (Mg–C-HAp) was introduced through dissolution-precipitation treatment of hydroxyapatite containing magnesium (Mg-HAp) based on a black sea urchin (arbacia lixula) shells as novel biogenic materials. Based on chemical composition analysis, the Mg–C-HAp formed A- and B-type CHAp, which contained high carbonate ions. The Ca/P ratio of Mg–C-HAp was 1.707, very close to the biological bone apatite of 1.71. The Mg content in Mg–C-HAp was also relatively high, with the Mg/(Ca + Mg) ratio of 0.139, which is beneficial for antibacterial agents. The morphology of Mg–C-HAp showed particles with nanosize that provide a large surface area of ion promotion. The antibacterial test revealed that the Mg–C-HAp performed high antibacterial activity against Pseudomonas aeruginosa. The Mg–C-HAp-based porous scaffolds were then fabricated using the freeze-drying method with variations of polyvinyl alcohol (PVA) and gelatin fraction. According to the physicochemical analysis, the addition of PVA and gelatin in the scaffold structure decreased the crystallinity of the Mg–C-HAp/PVA/Gel scaffold. This lower crystallinity indicates high biodegradability, which is good for new bone growth. The macropores of the Mg–C-HAp/PVA/Gel scaffold were appropriate for new bone and blood vessel formation. The micropores of the Mg–C-HAp/PVA/Gel scaffold can be a medium for cells to grow. The microporosity of the Mg–C-HAp/PVA/Gel scaffold was also suitable for cell nutrient promotion. The compressive strength of the Mg–C-HAp/PVA/Gel scaffold was sufficient for bone regeneration. The Mg–C-HAp/PVA/Gel scaffold demonstrated high antibacterial activity against P. aeruginosa, so the Mg–C-HAp/PVA/Gel scaffold can maintain the role of Mg and carbonate content for antibacterial purposes. The good physicochemical, mechanical, and antibacterial properties of the Mg–C-HAp/PVA/Gel scaffold represented its suitable characteristics for antibacterial bone scaffolds.

Corrosion Enhancement of PM Processed Magnesium by Turning Native Oxide on Mg Powders into Carbonates

In addition to its use as a lightweight material, pure magnesium is a promising candidate for prospective bioimplants considering its excellent biocompatible properties. Regardless of what Mg application is used, the ultimate goal is to improve magnesium's mechanical properties and degradation behaviour. Because of the high affinity for oxygen native oxide layer of gas-atomized powders is naturally formed in contact with the atmosphere. S/TEM investigation of the native oxide of the Mg powder particles revealed a nonhomogeneous nano-crystalline MgO layer. MgO is relatively soluble in water and does not provide sufficient corrosion protection. Among various surface treatment methods, conversion of the non-protective magnesium oxide to carbonate products is possible depending on the environmental conditions. This work used a simple experimental method using CO2 and water vapour to achieve surface carbonation of Mg powders. Two carbonated samples and pure magnesium were prepared by direct extrusion. The samples after carbonation retained good mechanical properties and the layer of carbonates had a significant impact on corrosion resistance. 1 day carbonation resulted in transformation of native oxide into amorphous layer and reduction of corrosion rate. Longer carbonation (10 days) revealed layer growth and transformation of native oxide to crystalline nesquehonite structure.

Layer-by-Layer Construction of Antibacterial and Anticoagulant Blood Contacting Materials.

Vascular transplantation is a common treatment for Cardiovascular disease (CVD). However, the mismatch of mechanical, structural, or microenvironmental properties of materials limits the clinical application. Therefore, the functional construction of artificial vessels or other blood contact materials remains an urgent challenge. In this paper, the composite nanofibers of polycaprolactone (PCL) with dopamine and polyethylenimine (PEI) coating are first prepared, which are further self-assembled by anticoagulant hirudin (rH) and antimicrobial peptide (AMP) of HHC36 through layer-by-layer (LBL) method. The results of FTIR and XPS analysis show that hirudin and AMP are successfully loaded on PEI-PDA/PCL nanofibers and the hydrophilicity is improved. They also show good mechanical properties that the ultimate tensile strength and elongation at break are better than natural blood vessels. The antibacterial results show that the antibacterial effect is still 93% against E. coli on the fifth day because of the stable and continuous release of HHC36 and rH. The performance of anticoagulant activity also exhibited the same results, which APTT is even 9.7s longer in the experimental group than the control group on the fifth day. The novel materials would be effectively solve the formation of thrombosis around artificial blood vessel grafts and the treatment of inflammation.

A Single Component, Single Layer Flexile Foam Evaporator with the Higher Efficiency for Water Generation.

One of the greenest and promising ways to solve the problem of freshwater crisis is surface solar steam generation from seawater. A great number of photothermal materials with multi-component and multi-layered delicate yet complex structures often suffer from either low evaporation rate or high energy loss. Here, we present a single component foam evaporator with steam generation rate of up to 4.32kg m-2 h-1 under 1 sun irradiation. The evaporator is constructed from an aniline oligomer as a single light-absorbing component, covalent linked with polyethylene glycol to form a monolithic polymer foam. Floating on the seawater, the foam has absorbance of 99.5% over the entire solar spectral range and low thermal conductivity (0.0077W K-1m-1) that effectively retains heat in the material and at the interface. After 3 months of continuous outdoor natural sunlight irradiation, the evaporator maintains a stable and durable evaporation rate. Moreover, the materials have good mechanical properties (7.48MPa young's modulus and 57.38% elongation at break) and excellent chemical resistance in 10 common organic solvents and aqueous solutions of pH = 1 to 14. This study provides a new system and strategy for desalination, steam power generation, treatment of polluted water and sewage, etc. This article is protected by copyright. All rights reserved.

Sulfonated cobalt phthalocyanine/NH2-MIL-125 heterojunction modified electrospun nanofiber membrane for emulsion separation and PMS-photocatalysis synergistic degradation

Membrane technology for wastewater remediation has generated significant interest, however, the single functionality, dull wettability and easy fouling property of the membrane hinder its practical application. Herein, a self-cleaning and multi-use superwetting nanofiber membrane was prepared by electrospinning and subsequent spraying technique. The sulfonated cobalt phthalocyanine/NH2-MIL-125 (CoPcS/NMIL) heterojunction was uniformly enrobed over polyethylene terephthalate (PET) electrospun membrane derived from waste PET bottles. The unique CoPcS/NMIL heterojunction exhibited a dual driving effect in photocatalytic activity and membrane wettability. Therefore, the fabricated CoPcS/NMIL@PET composite membrane demonstrated its capability to address complex water pollution issues effectively. The composite membrane exhibited notable flux permeation ability (538–3180 L m−2 h−1) and achieved excellent separation efficiency of over 99 % for diverse oil-in-water emulsions under the gravity filtration condition. Notably, the membrane can efficiently deal with stubborn high-viscosity crude oil fouling profiting from the photocatalytic self-cleaning function. A high flux recovery ratio of 93.6 % and a low irreversible fouling resistance ratio of 6.4 % can be obtained after 30 min of visible light irradiation. Impressively, CoPcS/NMIL@PET membrane exhibited enhanced permeation flux, separation efficiency and self-cleaning capacity compared to NMIL@PET membrane. Meanwhile, the CoPcS/NMIL@PET-activated peroxomonosulfate (PMS) system exhibited extremely high degradation performance for RhB under visible light with the degradation efficiency of 98 % within 10 min, suggesting its potential in the rapid purification of water-soluble organic pollutants. In addition, the CoPcS/NMIL@PET membrane has good chemical stability and mechanical properties for potential long-term use. Moreover, the demulsification mechanism in oil-water separation and PMS-photocatalysis synergetic mechanism over the fabricated CoPcS/NMIL@PET membrane were also investigated in detail. The research offers a promising approach for the design and fabrication of novel nanofiber membranes that incorporate photosensitizers and MOFs functional surfaces to address the challenges associated with such wastewater treatment.