Good Breathability Research Articles

Spray-Coated Ultrathin and Porous Films for Physiological Sensing and Force Detection.

Epidermal electronics employed on human skin for the long term require good breathability and nonforeign wearing. In this work, we combine phase separation and spray coating to fabricate a porous and ultrathin electrode within minutes as well as micrometer-scale porous pressure sensors. The resulting electrodes show a water vapor transmission rate of 18.4 mg·cm-2·h-1, sheet resistance of 5.2 Ω/sq, and thickness below 5 μm. The introduction of the biogel further reduced the electrode-skin impedance, which is lower than that of the commercial gel electrode, indicating that the electrode can have a high degree of conformal contact with the skin. The epidermal electronics prepared by this strategy exhibit an excellent performance in force sensing. Such results strongly prove the efficiency and practicality of the strategy.

3D Bristle-Structured, Knitted-Fabric-Based Triboelectric Sensors for Machine Learning-Based Motion Recognition.

With the development of electronic technology, triboelectric-based sensors have been widely researched in fields such as healthcare, rehabilitation training, and sports assistance due to their manufacturing convenience and self-powering advantages. Among them, 3D fabric-based triboelectric sensors not only possess advantages such as easy mechanized production, good breathability, and ease of wearing but also their unique 3D structure enhances the specific surface area, thereby amplifying the sensitivity. This study proposes a 3D bristle-structured fabric made by a digital knitting technology that has not been studied widely for triboelectric devices. By applying the 3D bristle structure with a large specific surface area to the single jersey fabric, the effective contact area during friction can be increased, resulting in a higher surface charge density. Additionally, the microcapacitor-like effect provided by the numerous microstructures allows the device to store more surface charge, further improving the output performance. The study systematically investigates the output performance of four different structures assembled by single jersey and 3D bristle-structured fabrics. The optimal sample exhibits a 57% higher output voltage than that of the reference 2D fabric sample. The 3D bristle-structured fabric demonstrates linear high sensitivity and distinct output performance when used as a sensor. Finally, a machine learning integration is applied to judge motion to assist a baseball pitcher in a self-training system.

Core-Shell Composite Nanofibers with High Temperature Resistance, Hydrophobicity and Breathability for Efficient Daytime Passive Radiative Cooling.

Radiative cooling technology, which is renowned for its ability to dissipate heat without energy consumption, has garnered immense interest. However, achieving high performance, multifunctionality, and smart integration while addressing challenges such as film thickness and enhancing anisotropic light reflection remains challenging. In this study, a core-shell composite nanofiber, PVDF@PEI, is introduced and designed primarily from a symmetry-breaking perspective to develop highly efficient radiative cooling materials. Using a combination of solvent-induced phase separation (EIPS) inverse spinning and (aggregation) self-assembly methods (EISA or EIAA) and coaxial electrostatic spinning (ES), superconformal surface anisotropic porous nanofiber membranes are fabricated. These membranes exhibit exceptional thermal stability (up to 210°C), high hydrophobicity (contact angle of 126°), robust UV protection (exceeding 99%), a fluorescence multiplication effect (with a 0.6% increase in fluorescence quantum efficiency), and good breathability. These properties enable the material to excel in a wide range of application scenarios. Moreover, this material achieved a remarkable daytime cooling temperature of 8°C. The development of this fiber membrane offers significant advancements in the field of wearables and the multifunctionality of materials, paving new paths for future research and innovation.

Amoxicillin-laded sodium alginate/cellulose nanocrystals/polyvinyl alcohol composite nanonetwork sponges with enhanced wound healing and antibacterial performance

Wound healing is a complex process and reuires a long repair process. Poor healing effect is normally a challenge for wound healing. Designing sponge dressings with drug-assisted therapy, good breathability, and multiple functional structures effectively promotes wound healing. In this work, a flexible amoxicillin-laded (AMX) sodium alginate (SA)/cellulose nanocrystals (CNCs)/ polyvinyl alcoho (PVA) (SA/CNCs/PVA-AMX, SCP-AMX) wound dressing was designed and built with an excellent porous structure, suitable porosity, and anti-bacterial properties for promoting wound tissue reparation. The porous structure of the wound dressing was fabricated by freeze-thawing cyclic and freeze-dried molding process. This wound dressing exhibited a 3D porous structure for soft-tissue-engineering application, including high porosity (84.2%), swelling ratio (1513%), tensile strength (1.79 MPA), and flexibility. With the inhibition zones of Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) being 1.96 and4.58 cm, respectively, this wound dressing demonstrated good antibacterial activity against E. coli and S. aureus. More importantly, wound healing assay in vivo indicates that SCP-AMX could inhibit wound infection, promote collagen deposition, reduce inflammation, and accelerate granulation tissue and wound healing. Thus, the reported wounding dressings present excellent biocompatibility, high antibacterial activities, and excellent biosafety with great potential in wound healing applications.

Designing self-cleaning & flexible multifunctional wearable heater

Wearable fabric heater has aroused wide concern in personalized temperature regulation. However, it is still challenging to develop multifunctional wearable heater with multimodal & fast thermal response, good flexibility, strong abrasion, excellent washability, good antibacterial performance, and recyclability. To accomplish these properties, a self-cleaning & flexible multifunctional wearable heater is designed by spraying mixture of Ti3C2Tx MXene/ZnO composite and PDMS on cotton fabric (CF-MZP). The designed CF-MZP fabric heater shows high photothermal/electrothermal/synergistic conversion properties and fast thermal response (just 30 s). Furthermore, the CF-MZP fabric possesses excellent superhydrophobic and self-cleaning properties that endow the heater with strong abrasion, excellent washability, and good antibacterial performance. Interestingly, the CF-MZP heater also exhibits good breathability, durability and flexible performance, which is demonstrated as a flexible wearable heater attached to knuckle position of a human body, showing steady temperature of around 50.9 °C at a voltage of 3 V or about 80.5 °C upon NIR lamp (0.2 W cm-2) irradiation, either relaxed and bending (90° or 180°) states. Furthermore, the CF-MZP heater can be recycled by separating ordinary oil-water mixture and high viscous heavy oil. Consequently, the designed CF-MZP fabrics provide a good perspective application in self-cleaning, recycled, and flexible wearable heaters.

Advanced Applications of Porous Materials in Triboelectric Nanogenerator Self-Powered Sensors.

Porous materials possess advantages such as rich pore structures, a large surface area, low relative density, high specific strength, and good breathability. They have broad prospects in the development of a high-performance Triboelectric Nanogenerator (TENG) and self-powered sensing fields. This paper elaborates on the structural forms and construction methods of porous materials in existing TENG, including aerogels, foam sponges, electrospinning, 3D printing, and fabric structures. The research progress of porous materials in improving TENG performance is systematically summarized, with a focus on discussing design strategies of porous structures to enhance the TENG mechanical performance, frictional electrical performance, and environmental tolerance. The current applications of porous-material-based TENG in self-powered sensing such as pressure sensing, health monitoring, and human-machine interactions are introduced, and future development directions and challenges are discussed.

Skin-like breathable wound dressings with antimicrobial and hemostatic properties

Wound healing requires a contamination-free, sterile, and breathable environment. However, to develop an ideal wound dressing with all these functionalities simultaneously poses significant challenges. In this study, we designed a wound dressing that mimics the structure of skin with good breathability and protective functions. The wound dressing consists of a hydrophilic Poly(3-hydroxybutyrate-co-4-hydroxybutyrate) (P34HB) membrane coated with zinc oxide nanoparticles and a hydrophobic polyvinylidene fluoride (PVDF) membrane. Meanwhile, plasma treatment was also utilized to bond the two layers, resulting in an enhancement of 60 % in mechanical properties. The crosslinked fibrous membranes exhibited uniform stress distribution when stretching. Due to the unique structures of the wound dressing, it demonstrates wound exudate management, antibacterial functions, and hemostatic properties. The hydrophobic layer guided wound exudate towards the hydrophilic layer and the zinc oxide nanoparticles acted as a barrier against external bacteria and released zinc ions to inhibit bacterial growth in the exudate. Moreover, the water vapor transmission rate (WVTR) was measured to be over 86.55 kg/m2/day, the hemolysis rate was 2.38 %, and an impressive 81.98 % healing rate was recorded during in vitro wound healing. This skin-mimicking wound dressing shows great potential as a promising solution for the therapy of chronic wounds and infections.

Rapid identification of silk products by attenuated total reflection–mid-infrared spectroscopy and extreme learning machines

Silk is a high-quality fiber of natural protein and its amino acid composition is close to that of the human skin. The texture of pure silk is elegant, soft and comfortable to wear, with good breathability and hygroscopicity, as well as excel dirt absorption and sterilization. It is essential to identify natural pure silk products and various non-silk and adulterated silk products with other fibers. The work focuses on exploring the feasibility of combining attenuated total reflection–mid-infrared (ATR-MIR) spectroscopy feature selection, extreme learning machines (ELM), and ensemble and for rapid identification of silk products. A dataset consisting of 70 silk samples and 83 other fiber samples was prepared. The dataset is split evenly into training and test sets for building and validating predictive models. Simulated annealing (SA) was used for pre feature selection. A total four kinds of ELM models including full-spectrum, subspace and ensemble models were developed and compared. The optimized local model and the ensemble model achieve the best and most stable performance, i.e., with 100% accuracy. It seems that SA, ELM combined with ATR-MIR technique may be a potential alternative to traditional analytical methods of silk identification, which can avoid time-consuming and labor-intensive chemical analysis.

Technological progress in Russian military sports suits: the history of the use of materials and fabrics from the end of the 19th century to the beginning of the 21st century

The subject of the study is technology in military sports suits of Russian military personnel. The object of the study is the progress in the production technologies of military sports suits. The author examines in detail the history of the use of various materials and fabrics for the production of military sports suits, from the end of the 19th century to the beginning of the 21st century. Special attention is paid to the analysis of the properties of various materials. The author shows that fabrics with high strength, wear resistance and good breathability are most suitable for military sports suits of Russian servicemen. The fabrics used for the production of military uniforms must meet a number of requirements. At the same time, such properties of fabrics as crease, drapery, hydroscopicity, dust capacity, heat-shielding properties, shrinkage, thread shedding, thread expansion in seams, sliding should be taken into account. The main research methods were theoretical methods – the method of analysis, generalization, systematization, classification of literary sources on the research topic. The novelty of the research consists in a comprehensive analysis of the basic properties, characteristics and requirements for fabrics used for the manufacture of military suits. A retrospective analysis and comparison of costumes from different eras were carried out. The main conclusion of the study is that from the end of the 19th century to the 21st century, the use of fabrics for military clothing has undergone significant changes. It is shown that at the end of the 19th century, military clothing was mainly made from natural fabrics such as cotton, wool and linen. With the advent of synthetic fibers in the 20th century, fabrics became more durable, lightweight, quick-drying and resistant to external factors. In the 21st century, with the development of fabric production technologies for military clothing, special mixtures of natural and synthetic fibers, as well as membrane materials, began to be used to provide high protection, comfort and functionality for military personnel. The author's special contribution to the study is the generalization of the results of various studies, the comparison of the main characteristics of fabrics used in various historical times with modern fabrics and materials.

Superelastic bamboo fiber-based spongy aerogel for flexible piezoresistive sensors with wide response range and high sensitivity

Superelastic, breathable, and flexible piezoresistive sensors with excellent sensing performance are drawing tremendous attention in wearable electronics and sleeping furnishings. However, simultaneous realization of their high performance is still a huge challenge. In this study, inspired by the pore structure of natural sponges, a high-performance sponge-like bamboo fiber/graphene oxide aerogel piezoresistive sensor (M−CBF−rGO) was prepared utilizing bamboo fibers (BFs) and graphene oxide (GO) as raw materials through freeze casting and carbonization. Benefiting from the unique porous structure with effective absorbing/releasing energy, the M−CBF−rGO aerogel sensor exhibits excellent superelasticity (not being destroyed under 90 % deformation), mechanical durability (7,000 cycles), and good breathability. Moreover, the M−CBF−rGO sensor demonstrates ultra-high strain sensitivity (892.9), a wide detection range (0–300 kPa), and a fast recovery time (20 ms). Taking advantage of these benefits, the M−CBF−rGO sensor can not only be applied to detect human signals ranging from finger motion to swallowing recognition, but also integrated into the cushioning materials of upholstered furniture to generate a sensing array for monitoring and recogniting human activity including sitting postures and sleeping positions in real-time. This sensor demonstrates the potential application prospects in the fields of human health diagnosis, smart wearable products, and intelligent upholstered furniture.

Washable and stable coaxial electrospinning fabric with superior electromagnetic interference shielding performance for multifunctional electronics

There is an urgent need for multifunctional and wearable smart devices to address the growing environmental impact on the human body, especially for pregnant women. However, it is big challenge to explore fabric combined multi-functions, such as EMI shielding, electrical therapy and biomotion detection while maintaining their intrinsic durability and washability. Here, we have employed an efficient coaxial electrospinning technique, followed by Ag precursor reduction and polydimethylsiloxane spraying to fabricate a multifunctional film which contains core–shell fibers with polyurethane/carbon nanotube (CNT) as core and polyurethane/Fe3O4 as shell. The CNT and the Ag nanoparticles (AgNPs) form double conductive network for EMI shielding, electrical heating and biological motion detection. The Fe3O4 provides magnetic loss and helps the fibers to provide rich attachment sites for AgNPs. The obtained film has an excellent combination of high EMI SE (110.0 dB in X-band), large Joule heating (up to 230 °C at 3 V), good sensing performance and large sensing range of 230 % strain. In addition, it showed an extremely superior durability and stability in complex conditions, good breathability and wash stability, ensuring the comfort wearing. This study offers an outstanding paradigm to construct next generation intelligent fabric combined versatility, stability and wearing comfort for protection of pregnant women and military solider.

Breathable and washable MXene@gallic acid cross-linked textile assisted by borax for personal multi-protection wearables

Achieving multifunctional integration with comfortability and durability comparable to conventional textiles is one of the ultimate pursuits of personal protective wearables. Herein, a multi-protective textile with breathable, moisture-permeable and washable properties is reported, which is realized by cross-linking of electroactive MXene@gallic acid (MG) with the cationized cotton. Cationic modification reduces the charge repulsion between MG and cotton fibers, and promotes the deposition of conductive media on textile surface. After borax (STB) cross-linking, the obtained textile exhibits superior service stability and can be subjected to conventional washing, exhibiting antioxidant stability during natural storage. Importantly, the cross-linked textile inherits the properties of good breathability, softness and bendability as the original fabric. With the outstanding conductivity (260 mS/cm) and high absorptivity of the solar spectrum (0.920), the textile was used for Joule heating and solar heating, demonstrating their potential in the field of thermal management. Meanwhile, the textile demonstrates excellent antibacterial activity against Gram-negative Escherichia coli and Gram-positive Staphylococcus aureus, and maintained satisfactory antibacterial effect (>90 %) even after ten washing cycles. This facile strategy for fabricating personal protective textiles, based on cross-linking cotton fiber with electroactive mediators offers favorable durability, comfortability and multifunctionality, providing a scalable and sustainable approach for manufacturing multi-protective wearables.

Photoelectric dual-mode triggered phase change materials for all-weather personal thermal management and shape memory

To cope with the demand of more complex and variable applications, it is urgent to develop dual-mode triggered, breathable, and shape-memory wearable heaters for all-weather personal thermal management of composite phase change materials (PCMs). Herein, after high-temperature carbonization of ZnCo-MOF (metal–organic framework) nanosheet array grown in situ on flexible and breathable carbon cloth (CC) and subsequent encapsulation of polyethylene glycol (PEG), the as-prepared PEG/CC@Co/CNT (carbon nanotube) composite PCMs exhibited good breathability, mechanical strength (tensile strength of 9.15 MPa), thermal energy storage density (114.19 J/g), and shape memory due to the synergy of flexible CC skeleton and rigid PEG. More importantly, composite PCMs possessed excellent solar-thermal (93.7 %, 100 mW/cm2) and electro-thermals (94.5 %, 2.0 V) conversion and storage capacity, benefiting from the conjugation effect of high graphitized carbon/carbon heterostructure with fast electron/photon/phonon transmission and the localized surface plasmon resonance effect of Co nanoparticles. Therefore, the integration of solar heating and Joule heating into breathable composite PCMs can be accurately used for next-generation all-weather, all-season, dual-mode triggered personal thermal management, including indoor/outdoor, daytime/night, rainy/cloudy and other complex and changeable scenarios.

A water-resistance and breathable fabric-based sensor with high sensitivity for air and underwater applications

A wearable sensing device, it not only has good breathability to ensure long-term wearing comfort but also needs to have waterproof ability to avoid sweat erosion. However, most reported works only have breathability or waterproof ability, which greatly limits their application. Herein, we designed and fabricated a water-resistant and breathable sensor based on non-woven fabric via the simple methods of 3D direct writing and spray coating. The sensing principle of supercapacitive and the micro uneven structure of fibers endows the sensor with high sensitivity (77.19 kPa−1), wide detection range (0–65 kPa), fast response speed (within 50 ms), cycle stability (over 10,000 cycles). The stearic acid (STA) coating method enables the sensor with excellent hydrophobicity (water contact angle of about 160.9°) and waterproof ability that can work normally in humid environments and even underwater. Benefiting from the natural micropore structure of fibers, the sensor demonstrates excellent air permeability (359.4 mm s−1). As a result, the fabric-based sensor can monitor human motions, and physiological signals and recognize gestures in the normal open-air and underwater environment, demonstrating its huge potential in underwater applications.

Knitting-stitching bifacial metafabrics with switchable thermal and moisture transmissibility for multimodal dynamic personal thermoregulation.

Smart textiles with thermal and moisture management functionalities are highly desirable for enhancing human comfort and reducing weather-related health issues. However, achieving high-performance thermoregulatory fabrics that simultaneously exhibit reversible cooling and heating functions, and effective sweat management through industrial fabrication, remains challenging due to the lack of compatible textile technologies capable of manipulating hierarchical structures. Herein, a robust thermal and moisture-managing metafabric (TMM fabric) with a stitching-interlaced-knit structure is developed using industrialized machine knit technology. Unlike layered fabrics, this knitted structure endows the TMM fabric with different appearances on its two opposite surfaces for reversible photon management, while integrating these surfaces into an all-in-one construction using interlacing yarns. The interlacing yarns also serve as pathways for heat and moisture transmission, enhancing thermal conduction and water transportation. A coupling agent-assisted zinc oxide nanoprocessing is further applied to the cooling surface of the TMM fabric to improve solar reflectivity. The bifacial TMM fabric demonstrates on-demand radiative/evaporation cooling and photo-thermal heating capacities by simply flipping the fabric, achieving an effective temperature regulation of over 17 °C. Furthermore, the TMM fabric shows desirable electro-thermal performance, enabling it to protect the human body from harsh low-temperature conditions of -18 °C. Moreover, the TMM fabric demonstrates good breathability and robust mechanical properties. This facile structural design as a paradigm provides a new insight for producing scalable, robust and efficient personal thermoregulation textiles adaptive to superwide temperature changes using well-engineered textile structures.

Stretchable textile with ultra-high electromagnetic interference shielding performance based on porous wrinkled conductive network

The soaring growth of flexible electronic devices has boosted the demand for electromagnetic interference (EMI) shielding materials with excellent stretchability, stability and even breathability. However, it is still a challenge to develop conductive materials with outstanding stretchable EMI shielding performance. In this work, we developed a textile with porous wrinkled conductive network through in situ polydopamine-assisted deposition of silver nanoparticles (AgNPs) on wrinkled fiber mat and polydimethylsiloxane post modification. This unique wrinkled conductive networks endows the textile with excellent electrical conductivity (103700 S/m), good breathability, superhydrophobicity, and ultra-high stretchable EMI shielding properties. The EMI shielding effectiveness (EMI SE) of the textile reaches 101.1 dB in unstretched state and still maintains at 94.1 dB at 100 % tensile strain. The superhigh EMI SE under such a high strain is much higher than the previously reported results so far. Moreover, the textile shows exceptionally good cyclic tensile durability under 100 % stain. After 1000 tensile cycles with 100 % strain, the EMI SE of sample only drops by 3.8 %. This work provides a new path for developing stretchable high EMI shielding performance materials, which is of great significance to solve the EMI problems of emerging flexible and wearable electronic devices.

Pectin extracted from Premna Microphylla Turcz for preparation of a “sandwich” multi-property sensor film involved with deep eutectic solvent

An acidic deep eutectic solvent (DES, choline chloride/citric acid) was used to efficiently extract edible pectin from Premna microphylla Turcz (PMTP) and further prepare the film sensor with the purpose of “four birds with one stone” with the roles of extractant, coalescent, conductivity promoter and bacteriostatic agent. The optimized extraction process accorded with pseudo second-order kinetics, which was carried out at 78.2 °C for 1.29 h with the solid-liquid ratio of 1:34.66 g/mL with the yield up to 0.8210 g/g. After comprehensive characterizations of pectin product, a simple casting method was used to prepare the PMTP-DES based composite film. It showed that the composite film has promising compatibility, smooth surface, good breathability and ideal homogeneity. After 30 power on/power off cycles at 10 V, it exhibited satisfied conductivity stability. Moreover, the PMTP-DES film could be simply assembled as the flexible visual temperature sensor, with sensitive response at breathing or finger touch; it exhibited the highest sensitivity of 134 %/°C when the external temperature changed from 15 to 55 °C. Besides, the composite film also has preferable antimicrobial activity. The whole results and findings were aimed to contribute for the raw material, composition, preparation, and functions of the existing flexible functional materials.

Biocompatible Cryogel with Good Breathability, Exudate Management, Antibacterial and Immunomodulatory Properties for Infected Diabetic Wound Healing.

Due to the complex microenvironment and healing process of diabetic wounds, developing wound dressing with good biocompatibility, mechanical stability, breathability, exudate management, antibacterial ability, and immunomodulatory property is highly desired but remains a huge challenge. Herein, a multifunctional cryogel is designed and prepared with bio-friendly bacterial cellulose, gelatin, and dopamine under the condition of sodium periodate oxidation. Bacterial cellulose can enhance the mechanical stability of the cryogel by improving the skeleton supporting effect and crosslinking degree. The cryogel shows outstanding breathability and exudate management capability thanks to the interpenetrated porous structures. I2 and sodium iodides produced in situ by reduction of sodium periodate provide efficient antibacterial properties for the cryogel. The cryogel facilitates macrophage polarization from M1 to M2, thus regulating the immune microenvironment of infected diabetic wounds. With these advantages, the multifunctional cryogel effectively promotes collagen deposition and neovascularization, thus accelerating the healing of infected diabetic wounds.

PEGylated curcumin-loaded poly(vinyl alcohol)/Zwitterionic poly(sulfobetaine vinylimidazole)-grafted chitosan nanofiber as a second-degree burn wound dressing

Burn injuries damage skin function and increased the risk of infection. Using natural-inspired antibiotic-free nanofibrous in wound healing has attracted increasing attention. Here, mPEG-Curcumin (mPEG-CUR) was synthesized through a novel, cheap, and high-efficiency method, and incorporated onto poly(vinyl alcohol) (PVA)/zwitterionic poly(sulfobetaine vinylimidazole)-grafted chitosan (CS-g-PNVIS) nanofiber. Due to the lack of electrospinning capability of CS-g-PNVIS and its brittleness, to obtain nanofibers with uniform and bead-free morphology, PVA was used as an electrospinning aid polymer, so that the prepared nanofibers have suitable mechanical properties with an average diameter between 115 ± 18–157 ± 39 nm. The heat-treated nanofibers have adequate swelling and dimensional stability. Time-killing assay proved the antibacterial activity of the mPEG-CUR-loaded nanofibers towards Gram-positive and Gram-negative bacterium. The MTT investigation illustrated the non-cytotoxicity and biocompatibility of the nanofibers. In vivo studies exhibited significant improvement in the mean wound area closure by applying mPEG-CUR nanofibers. The mPEG-CUR-loaded nanofibers showed the highest antioxidant (86 %) power after 40 min. Moreover, nanofibers possess a desirable WVT rate (3.4 ± 0.24–5.5 ± 0.3 kg/m2.d) and good breathability and had the potential to supply a suitable moist environment in the wounded area. This approach can be the beginning of a new path in designing a new generation of nanofiber mats for wound healing applications.

Design and performance research on the automatic sweat-treating fabrics used for ski suits

Skiers sweat a lot during training, and the sweat will create a wet-cold type environment between the ski suit and the athlete, reducing the wearer’s comfort. In this study, high hygroscopic materials and hydrophobic functional particles were integrated onto the inner fabric of the ski suit by dipping, scraping, spraying and other methods. A kind of fabric with automatic sweat-treating function used for ski suits was developed and the sweat-guiding, sweat-absorbing, sweat-holding, breathing and thermal insulation properties of the samples were tested by using a liquid guiding performance tester, a water content tester, an infrared thermal imager, a thermal plate, an air permeability tester, a moisture permeability tester and other equipment. The results show that the method of changing the hydrophobic properties of different areas of fabric surface and combining and distributing fabrics with different absorbing properties can be used actively to guide the flow direction of sweat on the fabric surface. The samples designed in this study can effectively delay the time for the ski suits to enter the wet-cold type state. Treated samples can effectively protect the insulation layer from being affected by sweat and steam. Before and after sweat absorption, the temperature of the insulation layer of treated samples changes relatively slowly compared with the control group. After finishing, the breathability of the sample decreased, while it still had a good breathability. In conclusion, the automatic sweat-treating fabric developed in this study has good sweat-treating performance.