Geophysical Studies Research Articles

Damage assessment of Siverek Castle during the Kahramanmaraş Earthquakes (Mw 7.7 and Mw 7.6) on 06 February 2023: Remediation and strengthening proposals

On February 6, 2023, two significant earthquakes with magnitudes (Mw) of 7.7 and 7.6 struck Turkey, occurring nine hours apart. In addition to the tragic loss of over 50,000 lives in the earthquakes centered in Kahramanmaraş, hundreds of thousands of engineering structures, such as residences, schools, hospitals, historical landmarks, highways, and more, were severely damaged. This study assesses the damages and risk scenario following the Kahramanmaraş earthquakes concerning Siverek Castle. In addition, remediation and strengthening proposals, required to eliminate the damage and the possible risk, have been developed. The initial stage involved observational damage assessments on the castle and surrounding slopes as part of field studies, identifying five different types of damage and potential risks. Subsequently, a precise 3D digital model of the damaged castle and its slopes was generated using the digital photogrammetry method. Additionally, geological and geophysical studies were conducted in the field to determine the characteristics of the mound structure, historical castle walls, soil and rock on the slope. Non-destructive, geophysical methods consisting Vertical Electrical Sounding (VES), Seismic Refraction Method (SRM) and Multichannel Analysis of Surface Waves (MASW) measurements were specifically employed in the area with historical remnants. To verify the obtained data, five boreholes were drilled in the lower parts of the slope, and experimental studies were conducted to determine the soil and rock material properties of the slope. In the numerical studies, a total of 54 2D stability analyses were performed under static, long-term static, and dynamic conditions. Additionally, 1000 different probabilistic rockfall analyses were conducted, both in 2D and 3D, to calculate the run-out distance, bounce height, velocity, and kinetic energies of the blocks that fell or were about to fall during the earthquake. In the final stage of the study, remediation and strengthening recommendations were prepared for the strengthening of the fortification walls and slopes where failures occurred, and stability analyses were conducted. Consequently, a design proposal recommending five distinct approaches to remediate and strengthen the castle and slopes impacted by the Kahramanmaraş earthquakes was endorsed by the relevant authorities, and construction has commenced. When the remediation and strengthening works are completed, the security of the cultural heritage will be ensured, and it is planned to be opened to visitors.

Diapiric Structures in the Tinto River Estuary (SW Spain) Caused by Artificial Load of an Industrial Stockpile

The mouth of the Tinto River is located on the southwest coast of the Iberian Peninsula in the northwest of the Gulf of Cadiz. The river flows into an estuarine system shared with the Odiel River, commonly known as the “Ría de Huelva”. In the 1960s, a wide area of ancient salt marshes was transformed by a stockpile of industrial wastes of phosphogypsum, reaching a height of 35 m above the level of the salt marsh at its highest point. Two surveys using high-resolution seismic reflection in conjunction with a parametric profiler were carried out in 2016 and 2018. The purpose of these geophysical studies was the realization of a 3D model of the sedimentary units constituting the most recent filling of the estuary. The records present abundant extrusion structures located on the margins of the waste stockpiles, which break the visible stratification of the surficial units of the estuary. In some sectors, these structures have reached the estuarine surface and have, therefore, a morphological expression on the estuarine floor. The origin of these structures is interpreted as a vertical escape of fluidized sediments from lower units caused by overpressure from stacking.

Structure of the Hydrothermal System of Thermal Fields Inferred from Geological-Geophysical Modeling: A Case Study of the Kambalny Volcanic Ridge (Kamchatka)

Abstract ––Based on integrated structural and geophysical studies and generalization of geophysical, hydrogeological, mineralogical, geochemical and other data, it is shown that the southern cluster of thermal fields of the Kambalny volcanic ridge (South Kamchatka) is included in the modern hydrothermal system. New data on the structure of the steam hydrotherm discharge area investigated to a depth of about 300 m have been obtained. The structural and hydrodynamic connection between two thermal fields from this group has been established. The Kambalny Ridge geothermal system embracing all major clusters of thermal fields is assumed to have a single deep-seated source of heat supply.

Investigation of leachate infiltration on groundwater using georesistivity and natural electric field method around Ojoou-Olayanju’s dumpsite, Ada, southwestern Nigeria

The investigation of groundwater within the dumpsite environment is highly important in geophysical study. This is because the extent of interaction between the aquiferous medium and the contaminated zone could pose a serious threat to the end users especially humans when consumed. This research aimed at investigating leachate infiltration and its potential influence on groundwater at Ojoou Olayanju's Dumpsite using combining geo-resistivity and natural electric field (NEF) methods. In this study, five dipole-dipole and five NEF measurements were obtained using the Omega resistivity meters and PQWT-150 equipment respectively. The dipole-dipole method was deployed to obtain a 2D near-surface pseudo-section, and the NEF method was used to obtain the frequency curve and profile maps of electric potential difference. The dipoledipole results revealed the lateral variation in the resistivity along the traverses, suggesting that the materials within this near-surface are heterogeneous, and the closely spaced contours' varying gradients indicate fracture, which would facilitate potential leachate filtration. The NEF results revealed curves, and a subsurface image with respect to depth and profile distance. The points of convergence signals on the frequency model correspond to a medium with low resistivity on the profile map. The conductive medium is seen as being saturated with leachate, which suggests that very large portion of the study area around the dumpsite has been contaminated by leachate. Conclusively, it was revealed that leachate filtration is evidence especially at the topsoil and due to the presence of fractured zones, the groundwater quality is at risk of contamination by continuous filtration of leachate

The crust-mantle velocity structure beneath the Wudalianchi-Erkeshan-Keluo volcanic belt by joint inversion of receiver functions and ambient noise

The Wudalianchi-Erkeshan-Keluo (WEK) volcanic belt is a significant component of intraplate volcanism in Northeast China and is composed of the Wudalianchi, Erkeshan, and Keluo volcanic clusters. Using joint inversion of receiver functions and ambient noise, we construct a high-resolution 3-D S-wave velocity model of the WEK volcanic belt and its adjacent region, taking advantage of a deployed dense seismic array around this volcanic belt. There is a prominent low-velocity anomaly at 8–15 km depth beneath the Wudalianchi volcanic cluster, suggesting the presence of a crustal magma chamber. Low-velocity anomalies are also observed at 30–35 km depth beneath the Erkeshan volcanic cluster and 30–40 km depth beneath the Keluo volcanic cluster, resulting in discontinuous velocity structures at the Moho discontinuity. We further find a distinct low-velocity anomaly in the uppermost mantle beneath the WEK volcanic belt. Combined with previous geophysical and geochemistry studies, we propose a magma system scenario for the WEK volcanic belt. The upwelling molten material from the asthenosphere accumulated in the uppermost mantle and the magma chamber was formed, which provided the same uppermost mantle magma sources for the WEK volcanic belt.

Multi-Sensor Satellite Images for Detecting the Effects of Land-Use Changes on the Archaeological Area of Giza Necropolis, Egypt

The World Heritage Committee has been meeting to discuss the arrangements of existing World Heritage Sites, and, on 22–26 October, the area from Giza to the Dahshur was included in the list of World Heritage Sites. According to the Egyptian Antiquities Authority (EAA), the groundwater levels at the Pyramids Plateau are too shallow, which threatens the ancient Sphinx and Pyramids in Giza, Egypt. In addition, many geophysical studies have been carried out in the archaeological area of Giza, which prove that the area is facing the risk of a high level of groundwater, specifically threatening the Sphinx. Recent developments in Earth observation have helped in the field of land monitoring such as land use changes, risk observation, and the creation of models for protecting cultural heritage sites. This study aimed to examine the impact of land use changes on on the archaeological sites of the Giza Necropolis area by integrating various data sources including optical satellite imagery and SRTM data during the period of 1965–2019. A historical database of Corona 1965 and Landsat 2009 data was investigated along with the new acquisitions of Sentinel-2 2016 and Sentinel-1 2016 and 2019. In addition, the radar Sentinel-1 SLC data were collected and analyzed for calculating the land subsidence value in the area of interest through two periods between 6–30 July 2016 and 30 July–15 December 2016. Various methods were implemented, including cluster outliers, the Moran index, and spatial autocorrelation to examine the changes in urban masses. Additionally, the relationship between groundwater leakage and land subsidence in the region was investigated. The analysis was carried out using Envi5.3, ArcMap10.6.1, and SNAP6.0 software to extract spatial data from the raw data. The results from our investigation highlighted rapid changes in urban areas between 1965 and 2019. The data obtained and analyzed from optical and radar satellite imagery showed that changes in land use can cause changes in the topographic situation by decreasing the level of groundwater, which adversely affects Egyptian monumental pyramids and the Sphinx. Land use analysis showed that the urban area represented 7.63% of the total area of the study area in 1965, however it reached 32.72% in 2009, approximately half of the total area in 2016, and in 2019, the urban mass area increased to nearly two-thirds of the total area. The annual growth rate between 1965 and 2019 was estimated by nearly 0.642 km2/year. These land-use changes possibly affected the land subsidence value (−0.0138 m), causing the rising groundwater level close to the Sphinx. Using the information obtained from our RS- and GIS-based analysis, mitigation strategies have also been identified to support archaeological area preservation.

The Role of Digital Elevation Models in Increasing the Accuracy of Geophysical Studies of Anthropogenic Metallic Pollution

The study focuses on improving the accuracy of geophysical investigations of anthropogenic metallic pollution using digital elevation models (DEMs). The methodology was tested at the Norilsk site, located in close proximity to the slag heaps of the nickel plant, based on DEM data obtained through unmanned aerial vehicles (UAVs) to conduct a detailed geomorphological analysis of the area. Geophysical methods such as the natural field (NF) method and frequency sounding were also used to identify zones of potential metallic pollution, as well as the characteristics and spatial positions of predicted permafrost layers. The main emphasis is on the advantages of integrating geophysical methods with DEMs and derived cartographic materials to improve the accuracy and reliability of surface metallic pollution detection and mapping, considering the geocryological situation within the study area. Geophysical methods of natural field (NF) and frequency sounding were employed to determine the geoelectrical properties of the study area. Reconnaissance surveys and flight missions were conducted to create the digital elevation model and orthoimage, and a surface water runoff map was developed based on the generated rasters and their interpretation. Based on the obtained geophysical data, zones of possible metallic pollution spread from the slag heaps were identified, which were confirmed through DEM analysis by the geomorphology of the study site. The distribution of specific electrical resistance fields was also interpreted in consideration of the collected data and validated through borehole drilling. It is worth noting that the integrated approach helped reveal the need to revise the interpretation plan, as only through the analysis of the nature and intensity of metallic pollution could the abnormally low resistance values in areas far from thermokarst lakes, with relatively shallow permafrost depths, be explained. Additionally, it became possible to qualitatively assess the zones of dust material accumulation.

Особенности сульфидной минерализации гидротермальной системы мыса Фиолент (юго-западный Крым)

As a result of generalization of geophysical studies, petro-paleomagnetic and structural-geomorphological analyses, as well as thermodynamic modeling, some features of ore formation in the hydrothermal system of Cape Fiolent (southwestern Crimea) under island arc conditions were revealed. It has been established that the main transformations of rocks of the Middle Jurassic igneous complex of Cape Fiolent occurred under the influence of hydrothermal fluids during the introduction of felsic intrusions during 168–140 Ma. The zones contain sulfide mineralization, the main minerals of which are pyrite, sphalerite, pyrrhotite, galena, chalcopyrite and arsenic pyrite. In the central parts of the hydrothermal alteration zone, massive sulfides are strongly weathered; these zones contain many secondary sulfates. In the marginal parts of hypergenic limonite, yellow-brown goethite prevails in the oxidation zone, yellow jarosite in the center, which is probably due to the large amount of pyrite in the center of the system, which gave more sulfuric acid during oxidation. The presence of native sulfur in the section testifies to the mixing of the acidified hydrothermal solution with seawater. Complex petro-paleomagnetic and magnetometric studies have shown that contact changes and transformation of the contrasting basalt-rhyolite formation occurred along the NNW-trending faults.

The main results of monitoring the power of the active layer at CALM sites of the Nadymsky object

Monitoring of the thickness of the active layer within the lake-marsh type of terrain in the northern taiga was carried out at three sites organized in 1997, 2013 and 2022. In these areas, two types of tracts are distinguished: frozen peat bogs and swampy runoff hollows with a lowered roof of permafrost (the cross-section of the sites is the same type, the only difference is in the thickness of the peat). The work methodology complied with the unified protocol of the international CALM program. Additionally, the surface settlement was assessed (based on leveling from a local benchmark), geophysical studies were carried out and the temperature of the active layer rocks was measured at different gullies. In swampy runoff hollows, hollows with open water and on specific mineral spots within peat bogs, the depth of the permafrost roof is 3–10 m. At the boundaries of peat bogs and in swampy runoff hollows, the thawing depth exceeds 2 m, and on peat bogs it varies from 0.8 to 1.6 m depending on the thickness of the organic layer and the condition of the ground cover. On peatlands with an organic layer more than 1 m thick and a continuous ground cover, the depth of the seasonal thawing layer in some places does not exceed 0.4 m. These peatlands respond poorly to climate change. The depth of the permafrost roof within thin peat bogs (less than 0.5 m of peat) with oppressed vegetation cover is currently more than 2 m, marking the beginning of the replacement of the seasonally thawed layer with seasonally frozen and the formation of areas with a lowered permafrost roof. Monitoring of soil temperatures in such areas has showed that a random combination of climatic factors in individual years can lead to short-term (two years) new formation of permafrost or the merging of seasonal permafrost with permafrost. Thus, the formation of non-merging permafrost is of a reciprocating nature.

Hydrochemical and geoelectrical investigation to determine the origin and spatial distribution of the salinization of the unconfined Plio-Quaternary aquifer of Tabeditt, Southern Tunisia

The expansion of irrigated agriculture and the overexploitation of groundwater in the Tabeditt region lead to a serious deterioration of the chemical quality of water. The compilation of hydrogeological and geophysical studies is essential in order to assess the quality of the Plio-Quaternary waters and to determine the origin of the salinization of these waters. In this study, hydrochemical analyses were carried out on groundwater samples in the Tabeditt region. Hydrochemical data have shown that the salinity in this area could exceed 6 g/L. The interpretation of major ion analyses demonstrates that mineralization is controlled by natural processes. The mineralization process consists of the dissolu-tion of evaporite minerals, namely gypsum, anhydrite, and halite. The geoelectrical study is carried out to obtain information about the distribution and quality of water in the Plio-Quaternary. Interpreta-tion of the resistivity models show the presence of two main zones: the first, near Tabeditt Wadi, is characterized by low values, indicating the influence of salt water in the groundwater and the second, located on the right bank of Wadi Jmal, is characterized by variable resistivity values, generally high, indicating the lateral changes in lithological facies, and the presence of fresh water. In such an arid region suffering from scarcity and degradation (or depletion) of water resources, it is important to implement a master plan that keeps under control the number of wells both known and unknown ones taping these aquifers.

Seismic probing of buried ancient terrane boundaries - insight into Fennoscandia’s Palaeoproterozoic continental formation

Terrane boundaries are usually mapped from structures, lithologies and ages of the bedrock geology. Geophysical studies occasionally used to image terrane boundaries at depth typically yield localised information. In this contribution we demonstrate that it is possible to map Palaeoproterozoic terrane boundaries over large areas in northwest Fennoscandia through modelling of the crustal structure using receiver function inversion. Our new model suggests the existence of three “arms” of thick crust interpreted as deep expressions of Palaeoproterozoic terrane boundaries. We also observe previously unknown high velocity lower crust that we relate to Palaeoproterozoic rifting. The deep structural information shows that crustal structures can be preserved over billions of years and yields a three-dimensional crustal terrane model. This model improves our understanding of Palaeoproterozoic tectonics and continent formation processes.

LITHO-STRATIGRAPHIC FEATURES OF THE LOWER CRETACEOUS DEPOSITS OF THE SKYBA AND DUKLA-CHORNOGORA NAPPES OF THE UKRAINIAN CARPATHIANS AND PROSPECTS FOR THEIR OIL AND GAS POTENTIAL

Lower Cretaceous sediments are widespread within the Skybа and Dukla-Chornorgora Nappes (Spas and Shypot Formations) over a considerable area. These deposits contain sandstones that can be industrial reservoirs for hydrocarbons. Such sandstones are described both on the surface and identified in deep wells. Thick sandy strata in the middle part of the Spas and Shypot formations formed as deposits of gravity flows at the second level of avalanche sedimentation, at the foot of the continental slope of the northern continental margin of the Tethys Ocean. Their formation is correlated with global regression in Aptian time. Porous sandstones of the Spas formations are present on the surface in the areas of the villages of Tershiv and Busovysko. They sometimes form bundles up to 60 m thick. They are exposed in the Oryv and Berehyv Skybas by deep wells 1-Lugy, 1-Shevchenko, and 4-Maksymivka. During the drilling of the 1-Shevchenko well from a depth of 6,900 meters, a film of oil and gas continuously flowed into the drilling mud. According to the results of industrial and geophysical studies, the section of the Spas formations of the second (lower) scale in the interval of 6,940–7,520 m was recognized as the most promising in terms of oil and gas potential. Two promising objects in the intervals of 7020–7070 and 6945–6985 m were identified, the oil and gas saturation coefficients of which are 65–70%. Similar sandstones are noted in the Hoverla sub-Nappe of the Dukla-Chornogora Nappe along the Balzatul River and its tributaries (Bila Tysa River Basin) as part of the Shypot Formation. Sandstones with an open porosity of 8–12 % were identified in the 1-Hrynyava and 1-Semakiv wells in the deposits of the Shypot Formation of the Skupiv sub-Nappe according to the results of industrial-geophysical research. When testing them in the 1-Semakiv well, from the total interval of 473–569 m, they received inflows of combustible gas and light oil with flow rates of 3,000 m3/day and 2.64 m3/day, respectively. The analyzed materials testify to the prospects of the Spas and Shypot formations in relation to the discovery of industrial accumulations of hydrocarbons.

Density structure of Kīlauea volcano: implications for magma storage and transport

SUMMARY A Bayesian linear regression to determine the bias in the Nafe–Drake relationship between compressional velocity and density provides an improved model for the density structure of Kīlauea volcano, Hawaiʻi. In previous work, we combined the results of seismic tomography with the Nafe–Drake relationship between compressional velocity and density to explain the large values of gravity disturbances overlying the summits and rift zones of the island's volcanoes. These results were used to determine mechanisms for gravitational instability of the island flanks. Here, we use laboratory measurements of the relationship of velocity and density for a wide range of Hawaiʻi island rocks as a prior in a Bayesian regression, with seismic tomography, to refine the 3-D density structure for Kīlauea volcano. This refined structure shows dense bodies (3220 kg m−3) between 5 and 8 km below sea level that underly regions of magma storage, found from geodetic and geophysical studies, beneath the summit and East Rift Zone of Kīlauea volcano. Above these bodies, density isosurfaces surround and cradle sources of pressure change determined from geodetic models, both at the summit and along the East Rift Zone. Continued subsidence of the summit following the 2018 eruption is aligned with a bowl-shaped density structure, formed primarily by density isosurfaces between 2800 and 2900 kg m−3 at 4–6 km depth. These surfaces underly the ∼3 km depth at which dyke injection initiates, are largely aseismic, and from their density values are inferred to contain high concentrations of olivine. Taken together, these density structures are consistent with an olivine-rich mush with variable porosity that increases in density with depth and provides a mechanism to form olivine cumulates both at the summit and along the rift zones. This structural framework for Kīlauea volcano is consistent with melt and mush transport occurring over a large range of depths to accommodate the growth and spreading of the volcano.

Integrated stratigraphical, hydrogeochemical, and geophysical studies to characterize the shallow groundwater aquifers in Wadi Araba area, western Gulf of Suez, Egypt

The construction of the New Galala City besides great mining (e.g., konoozmisr) and Seawater Reverse Osmosis Desalination Plant projects in the semiarid Gulf of Suez region of Egypt increases the demand for groundwater resources. So, the current research provides integrated stratigraphical, hydrogeochemical, and geophysical studies to investigate the shallow groundwater aquifers in Wadi Araba area on the western side of the Gulf of Suez. The stratigraphic column starts with pre-Cambrian basement rocks which are non-conformably overlain by sedimentary succession of Phanerozoic Erathem. A detailed land magnetic profile has been conducted and processed to estimate the aquifer’s geometrical parameters. This includes the subsurface spatial extension and thickness to delineate the prevailed subsurface structures in the study area. Lithostratigraphically, these aquifers are represented by the Paleozoic- lower Cretaceous siliciclastic-dominated sediments of the Nubia Group and fractured carbonate-dominated facies of the upper Cretaceous Galala Formation. Lithological characters, sedimentary facies (fluvial to shallow and open marine), microfacies types, and diagenesis processes (e.g., compaction, cementation, dissolution, and fracturing) are the main factors that affect the quality of the shallow aquifers in the study area. The main microfacies of the studied aquifers are quartz arenite, subarkose, sublitharenite, mudstone/wackestone, and packstone/grainstone. These facies are characterized by different primary and secondary porosities. According to the water sampling standard methods, nineteen groundwater samples were collected from the available hand-dug wells and springs from the Nubian sandstone aquifer and the Upper Cretaceous aquifer, respectively. Inductively coupled plasma–mass spectrometry (ICP–MS), titration, spectrophotometer and a flame photometer were used to obtain a complete chemical analysis. The results of hydrochemical analyses indicated that total dissolved solids (TDS) and concentrations of major ions as well in the lower Cretaceous aquifer increase toward the Gulf of Suez and in general higher than that of springs of the Upper Cretaceous Aquifer. The predominant factors influencing groundwater chemistry include seawater intrusion, evaporation, mineral alteration, dissolution of fossils, and ion exchange. Groundwater in the study area is unsuitable for drinking except in one sample and moderately suitable for irrigation with caution for higher salinity in samples located near the Gulf of Suez.

Groundwater characteristics using geophysical, geospatial, and hydrogeological studies in Peshawar Basin, Pakistan

Groundwater characteristics using geophysical, geospatial, and hydrogeological studies in Peshawar Basin, Pakistan

Оценка промышленной газоносности Ямальской и Гыданской нефтегазоносной области

In accordance with the strategic planning documents of the Russian gas industry, the development of the Yamal and Gydan oil and gas bearing regions is one of the priority tasks, as they are associated with the formation of a strategic reserve of gas resources and the creation of new gas production centers. The article analyses the spatial distribution of natural gas reserves in the oil and gas bearing areas of the Arctic region and concludes that the distribution of free gas resources is uneven both by section and by area. Some oil and gas bearing areas are characterized by a weak degree of geological and geophysical study. Depletion of the base fields in the Pur-Taz and Nadym-Pur oil and gas bearing areas raises the question of shifting the raw material base of the gas industry to the hard-to-reach areas of Yamal and Gydan, including the waters of the Kara Sea, the Ob, Taz and Gydan Bays. The paper provides a quantitative assessment of the level of commercial gas content of the Yamal and Gydan oil and gas bearing areas, including in the context of oil and gas bearing regions. It was determined that based on the technology of field development, processing and transportation scheme when assessing the prospects of development and options for monetization of gas resources, a zone of pipeline transport and a zone of liquefied natural gas are distinguished. Taking into account the current economic conjuncture of Arctic natural gas reserves development, it is reasonable and promising at this point in time to expand the resource base by developing satellite fields in Yamal and Gydan oil and gas bearing regions, which already have developed production, processing, transport and social infrastructure, as well as through additional exploration of discovered and developed fields and deposits.

Behavior of Amagmatic Orogenic Geothermal Systems: Insights From the Agua Blanca Fault, Baja California, Mexico

AbstractAmagmatic geothermal systems within regional‐scale orogenic faults are promising renewable resources for heat and possibly electricity production. However, their behavior needs to be better understood to improve their exploration and assessment of energy potential. To provide more insight, we report geochemical, geological, and geophysical studies from seven hot spring sites strung along a 90 km segment of the Agua Blanca Fault, which traverses a mountainous region of northern Baja California, Mexico. Our results show that topographic heads drive infiltration of meteoric water deep into basement rocks, where it is heated according to the local geothermal gradients. Long paths lead to long water residence times and high 3He/Hetotal fractions. The hot water ascends along preferentially permeable zones within the ABF, discharging at temperatures from 37°C in inland springs to 102°C on the Pacific coast. Higher discharge temperatures correlate positively with the degree of extensional fault displacement (a proxy for fault permeability). Correlations between hydraulic head gradients, residence times, and 3He/Hetotal of the thermal waters show that the hydraulic head gradient controls the length and depth of the flow paths, whereas the magnitudes and locations of the discharge sites are controlled by fault permeability. Optimal conditions at the coast allow the 120°C temperature threshold for electricity production to be reached at relatively shallow depths (<2 km), demonstrating the potential of orogenic geothermal systems not only for exploitation of hot discharging water but also for EGS exploitation of the hot rocks that surround the water upflow zones.

Экспедиция «Итуруп 2022–2023»: основные направления работ и предварительные результаты

The paper provides information on the objectives, methods, targets and some preliminary results of the expeditionary work carried out within the framework of the RSF project No.21-17-00049 by the employees of the Institute of Volcanology and Seismology of the FEB RAS, Institute of Marine Geology and Geophysics of the FEB RAS, Pacific Geographical Institute of the FEB RAS and Trofimuk Institute of Petroleum-Gas Geology and Geophysics of the SB RAS in 2022 and 2023. The main objectives of the expedition were geological-volcanological, hydrogeological, geophysical, tephrochronological, and paleoseismological studies. In accordance with the set objectives, field teams were formed, which began work in February 2022. On the basis of the data obtained during the expedition, previously unknown hydrothermal manifestations and seismic events on Iturup Island were identified. A number of geophysical and paleomagnetic surveys were carried out.

INVESTIGATION OF TEMPERATURE FIELDS DURING LOCAL INDUCTION HEATING OF THE CASING STRING IN THE WELL

One of the important tasks in geophysical studies of operating wells is the detection of behind the casing flows. The traditional complex of geophysical methods (thermometry, flow metering, composition methods, and others) does not always make it possible to detect the movement of fluid behind the well casing. To solve this problem, it is promising to use the method of active thermometry.Research technology using this method involves recording the temperature in the well during induction heating of a small section of metal casing. As a result of heat exchange between the heated section of the column and the liquid flow, a thermal disturbance is created in the annular flow channel. In the presence of behind the casing flow, heat will be carried away from the induction heating region in the direction of liquid movement and will be redistributed in the column above or below the heating interval. By recording the temperature of the casing during induction heating and after turning off the inductor, it is possible to establish the fact of cross-flow and quantify its flow rate.This paper studies the influence of the direction and flow rate of behind the casing flow on the unsteady temperature field in a metal casing during its local induction heating. The problem is solved numerically in the Ansys Fluent software package. The temperature field in the fluid in the wellbore is calculated taking into account free convection.The model temperature distributions obtained for different behind the casing flow configurations (direction, flow rate) can be used for quantitative interpretation, to determine the flow rate in the behind the casing flow channel by comparing actual and model temperature curves. To assess the intensity of behind-the-casing movement, time measurements at a “point” in the induction heating interval are also informative. The direction of flow is determined by the nature of the temperature distribution in depth above and below the induction heating section.

Electrical Resistivity Tomography (ERT) for investigating subsurface structures in the karst area of the Ek Leuntie Cave, Aceh Province

Ek Leuntie Cave, in the southern city of Banda Aceh, Aceh Province, is recognized as an educational media based on geopark sites because it holds a 7400-year paleotsunami track record. As a karst area, Ek Leuntie Cave is vulnerable to the impact of geological disasters such as earthquakes, sinkholes and subsidence. As an effort to reduce the negative impact of geological disasters, geophysical studies have been applied in the Ek Leuntie Cave Karst area. The study aims to identify the subsurface geological structure of the Karst area. The identification was carried out using the Electrical Resistivity Tomography (ERT) method of Wenner-Schlumberger configuration applied to two measurement trajectories that have South-North and West-East directions in front of the Ek Leuntie Cave door. ERT data acquisition results were then modeled in inversion using Res2Dinv software to produce a 2D model of the subsurface geological structure of the Ek Leuntie Cave karst area based on variations in rock resistivity values. Interpretation of subsurface geological structure modeling is validated with shallow drilling data (Hand Auger). The inversion modeling results show that the rock resistivity value in the Ek Leuntie Cave area reaches a depth of 30 m which has a resistivity value of 0 - 1000 Ωm. The results of the interpretation of resistivity values and validation of drill data show that the Ek Leuntie Cave area is covered by a layer of sand with fine to coarse texture and the layer below is a layer of limestone at a depth of ± 0.4 meters with a resistivity value of 50 - 250 Ωm. Limestone generally shows porosity with the possibility of caves or pores in the rock formation at Ek Leuntie Cave, making it vulnerable to damage from earthquakes, landslides, and subsidence. The results of the study are expected to provide updated information in efforts to develop the Ek Leuntie Cave geopark area.