Fiber Geometry Research Articles

The synergy of the matrix modification and fiber geometry to enhance the thermo‐mechanical properties of basalt fiber‐polypropylene composites for automotive applications

AbstractBasalt fiber reinforced polypropylene composites with two initial fiber lengths (3.2 and 6.4 mm) were fabricated using twin‐screw extrusion compounding. In the case of composites with smaller initial fiber length, basalt fibers predominantly served as nucleating agents for polypropylene thereby resulting in an increase in the degree of crystallinity. The addition of polypropylene‐g‐maleic anhydride (PP‐g‐MA) caused the matrix to become amorphous, which was due to the establishment of a fiber–matrix interphase. This behavior was different for the composites with relatively larger initial fiber length especially at higher fiber content. The reduction in fiber length in the composites caused a decrease in crystallinity, as this hindered the ability of the polypropylene matrix to form crystals. Addition of PP‐g‐MA established a fiber–matrix interphase thereby synergistically contributing to the increased matrix amorphousness of the basalt fiber reinforced polypropylene composites with 6.4 mm initial fiber length. Reduced fiber length due to processing also accelerated the thermal degradation of the composites with an initial fiber length of 6.4 mm. However, the reduction in fiber length due to processing resulted in increased fiber orientation, which contributed to the improvement in tensile and flexural properties of the basalt fiber reinforced polypropylene composites with an initial fiber length of 6.4 mm. At 30% fiber content, the tensile strength and modulus of basalt fiber reinforced matrix modified polypropylene composites with 6.4 mm initial fiber length improved by 18% and 13% as compared with the composites with 3.2 mm initial fiber length.

Study of Vector Bending Sensor in Various Configurations

A triple-core photonic crystal fiber (TCPCF) vector bending sensor has been introduced to study geometric parameter changes. The TCPCF shows a linear relationship between effective refractive index and input wavelength near 1.55µm. An asymmetrical geometry has been proposed for sensing both the direction and amplitude of the bend. The geometry of fiber creates an asymmetrical refractive index profile that leads to shifts in light speed in different fiber sections during the bend. The finite element method is used to study all sensor structures. The variation of the distance between cores, air hole diameter, and the angle between the side cores are studied. This sensor's need for precise and complex fabrication techniques is one of their challenges. Another challenge the design of these types of sensors faces is calibration for different environments and fabrication methods after fabrication is finished.

Bubbleless membrane contactor for enhanced ozone mass transfer and ozonation for water purification

Membrane contactor, a physical barrier separating two phases to introduce gas into aqueous solutions through the bubbleless process, has gained considerable development for its improved gas transfer and contaminant removal efficiencies for water purification. However, a comprehensive assessment of a contactor with liquid flowing on the shell side and gaseous ozone flowing on the lumen side is scarce for ozonation. Therefore, we have developed a membrane contactor equipped with commercial hydrophobic polytetrafluoroethylene (PTFE) hollow fibers and investigated theoretically and experimentally the interaction between ozone and solution. Mass transfer behavior was evaluated by comparing experimental value and computational model of corresponding coefficients. Phenol was then selected as a model contaminant to evaluate the treatment performance of membrane contactors in ozonation. Crucial operating conditions involving the gas/liquid flow rate, concentrations of ozone and phenol, pH and geometry of fibers were assessed for their impacts on both ozone mass transfer and pollutant degradation. The results showed that the membrane presented high chemical resistance to ozone and could achieve stable mass transfer through bubbleless aeration. Under the optimum operating conditions, the overall liquid mass transfer coefficient was 1.12 × 10−5 m/s. The percentage removal and mineralization of phenol with 30 min hydraulic retention time could reach ∼100 % and 21.1 %, respectively, which have demonstrated the high treatment efficiency of the membrane contactor as an alternative technique in water purification.

Retrofitting the Heart: Explaining the Enigmatic Septal Thickening in Hypertrophic Cardiomyopathy.

Hypertrophic cardiomyopathy is the most common genetic cardiac disease and is characterized by left ventricular hypertrophy. Although this hypertrophy often associates with sarcomeric gene mutations, nongenetic factors also contribute to the disease, leading to diastolic dysfunction. Notably, this dysfunction manifests before hypertrophy and is linked to hypercontractility, as well as nonuniform contraction and relaxation (myofibril asynchrony) of the myocardium. Although the distribution of hypertrophy in hypertrophic cardiomyopathy can vary both between and within individuals, in most cases, it is primarily confined to the interventricular septum. The reasons for septal thickening remain largely unknown. In this article, we propose that alterations in muscle fiber geometry, present from birth, dictate the septal shape. When combined with hypercontractility and exacerbated by left ventricular outflow tract obstruction, these factors predispose the septum to an isometric type of contraction during systole, consequently constraining its mobility. This contraction, or more accurately, this focal increase in biomechanical stress, prompts the septum to adapt and undergo remodeling. Drawing a parallel, this is reminiscent of how earthquake-resistant buildings are retrofitted with vibration dampers to absorb the majority of the shock motion and load. Similarly, the heart adapts by synthesizing viscoelastic elements such as microtubules, titin, desmin, collagen, and intercalated disc components. This pronounced remodeling in the cytoskeletal structure leads to noticeable septal hypertrophy. This structural adaptation acts as a protective measure against damage by attenuating myofibril shortening while reducing cavity tension according to Laplace Law. By examining these events, we provide a coherent explanation for the septum's predisposition toward hypertrophy.

Effect of Geometry and Size of Fiber Reinforced Plastic Deck Profile on Behavior of Bridges

Due to the important role that bridges play in rescue operations after an earthquake, it is necessary that these structures have a higher level of protection against seismic attacks. Earthquake identifies the weak points of the structure and causes the most damage there. Bridges are very vulnerable to these attacks due to their low degree of uncertainty. All bridges built before 1971 were designed with the elastic design method (permissible stress). In this method, the effects of plasticity, section cracking, and plastic deformation are not taken into account. The change of seismic locations based on the principles of elastic design is much less. It is because the structure experiences in a real earthquake, one of the consequences of which is the falling of the decks due to the loss of the support surface. The decision to strengthen the bridge was made when there were many bending and shear cracks on the king beams. The bridge was created. The use of FRP profiles can significantly prevent the damage caused by corrosion and is a good alternative to the traditional methods of strengthening the structure. In this study, a design for the deck of a steel bridge with I beams is presented. The shape of reinforcement using FRP fibers with vinyl ester resins has also been investigated, the effect of the geometry of FRP profiles has been investigated. The presented specifications are optimized to obtain a lasting shape and section, especially for the pultrusion process. FRP materials are light, resistant to corrosion and have high tensile strength. These materials come in different forms and range from multi-layer factory sheets to dry sheets that can be twisted on various structural forms before adding resin, is available. The durability and high tensile strength of FRP materials are among the advantages of these materials. The durability and long-term performance of FRP requires more research, which is ongoing and continues.

Low-loss and compact photonic lantern based on a step-index double cladding fiber.

The fulfilment of the adiabatic criterion is indispensable for the realization of a low-loss photonic lantern (PL), concurrently imposing a stringent restriction on the taper transition length of the PL. Here, by relaxing the adiabatic criterion, a low-loss and compact PL based on a step-index double cladding fiber (SI-DCF) is theoretically proposed and experimentally demonstrated. The use of SI-DCF can reduce the mode field diameter (MFD) expansion ratio during the tapering processing and greatly decrease the taper transition length required for adiabatic tapering. We initially evaluate the variation of both MFD and effective refractive index (RI) along the fiber tapering based on three types of fiber structures, including the modified standard single-mode fiber (SSMF), the graded-index fiber (GIF), and the proposed SI-DCF. In comparison with the commonly used fiber geometry, the SI-DCF can reduce the MFD expansion ratio from 77.73% to 38.81%, leading to more than half reduction of the tapering length for both 3-mode and 6-mode PLs. Then, two kinds of SI-DCF with different core diameters are fabricated to realize a 3-mode PL. The fabricated PL possesses a 1.5 cm tapering length and less than 0.2 dB insertion loss (IL). After splicing with the commercial few-mode fiber, the PL has an average IL of 0.6 dB and more than 13 dB LP11 mode purity over the C-band. Finally, a transfer matrix measurement indicates that the fabricated PLs have a mode coupling of less than -10 dB at 1550 nm.

Insights on the bearing response of glass fiber‐reinforced stainless steel laminates: Investigating the influence of natural fiber and specimen geometry

AbstractThis study delves into the bearing response of two types of Fiber Metal Epoxy Laminates (FMLs): Glass Fiber/Stainless Steel laminates and Glass Fiber/Jute/Stainless Steel laminates, where a portion of glass fiber is replaced with jute. The primary focus is to assess the impact of introducing natural fiber (jute) into FML on its pin‐type bearing performance, considering various edge‐to‐hole ratios (e/D), width‐to‐hole ratios (W/D), and stacking orders. The study aims to understand how these parameters influence the bearing load and failure modes of the laminates. Observations reveal that variations in e/D and W/D ratios, along with the stacking arrangement of materials in the FMLs, exert a significant influence on the ultimate load‐bearing capacity of the pinned joint. It is observed from the study that, for the two stacking sequences considered, the load bearing capacity of the FMLs with W/D ratio 6 is greater than those with W/D ratio of 4 by a maximum of 23.06%. Moreover, if the weight fraction of the glass fiber content in the FML is reduced, the ultimate load bearing capacity of the FML also gets curtailed to a maximum extent of 44%. The experimental findings suggest that the prepared fiber metal laminate, characterized by lower weight, cost‐effectiveness, and enhanced environmental friendliness, exhibits a substantial capacity to withstand bearing loads. Consequently, it emerges as a promising candidate for the construction of structures such as storage silos, offering a balanced combination of structural performance and sustainability.Highlights FML bearing performance: Glass/Stainless versus Glass/Jute/Stainless. Influence of e/D and W/D ratios on pin‐type bearing. Stacking order impact on load‐bearing capacity. Lightweight, cost‐effective, and eco‐friendly FMLs. Promising for silo construction: structural and sustainable.

Review on Fundamental Considerations During Lignocellulosic Fiber Characterization in Light Micromechanical Analysis of Their Composites

Lignocellulose fibers (Cellulosic fibers) are among the major agricultural resources from plant whose potentials are not exploited in some cases and/or underexploited in many cases. If their potentials for industrial application could be exploited, selling the fibers for manufacturing uses would be a win-win situation for both the industries and the farmers, and provide the latter with a much needed source of additional income since composite material reinforced with lignocellulose fibers can be used for diverse application including the production of parts in automotive industry. For this to be successful, it is mandatory to make fiber level characterization. In this process, there are various determinants that affects the characteristics of lignocellulose fiber including agro-ecological zone, plant age from which the fiber is extracted, lignocellulose structure, fiber extraction method and subsequent treatment to enhance properties. This review, therefore, presents the basics of lignocellulose fiber potential and insight into selected deliberation related to fiber level characterization in light of micromechanical analysis for new biocomposite under development. Included in this review, there are considerations to be potted during characterization at fiber level. For fiber diameter measurement and estimation, the following considerations are reported in this paper: measurement method validation, proper cross-section and fiber geometry assumption, lignocellulose structure and internal holes; enough sample consideration, incorporation of analytical method for cross checking. Likewise consideration during estimating fiber density, single fiber tensile strength and stiffness are review and discussed in this review.

Modified plastic damage model for steel fiber reinforced concrete

AbstractSteel fiber reinforced concrete (SFRC) structures have been widely adopted and attracted great research attention due to their excellent performance in resisting tension and flexure bending. However, the existing analytical and numerical analyses of SFRC structures rely mainly on the experimental data of material tests, thereby being suitable for a case‐by‐case basis. This is due to the lack of a general and reliable constitutive material model for SFRC, which analytically considers the fiber‐dependent parameters such as fiber geometry, fiber stiffness, and interface properties of fibers and concrete matrix. This study presents an approach to modify the concrete plastic damage model to represent the SFRC material constitutive relations for simulating the structural behavior of SFRC. In this approach, the general procedure to integrate the bridging effect of fibers through the pull‐out mechanism into the constitutive relation of SFRC was proposed. The comparison between the numerical and experimental results was conducted to verify the reliability of the proposed model. The results demonstrated the proposed model could well represent the material performance of SFRC and the numerical simulations could capture reasonably the effect of the volume fraction, geometry, and properties of fibers on the structural response of SFRC.

Coherent Imaging with Photonic Lanterns

Photonic lanterns (PLs) are tapered waveguides that gradually transition from a multimode fiber geometry to a bundle of single-mode fibers (SMFs). They can efficiently couple multimode telescope light into a multimode fiber entrance at the focal plane and convert it into multiple single-mode beams. Thus, each SMF samples its unique mode (lantern principal mode) of the telescope light in the pupil, analogous to subapertures in aperture masking interferometry (AMI). Coherent imaging with PLs can be enabled by the interference of SMF outputs and applying phase modulation, which can be achieved using a photonic chip beam combiner at the backend (e.g., the ABCD beam combiner). In this study, we investigate the potential of coherent imaging by the interference of SMF outputs of a PL with a single telescope. We demonstrate that the visibilities that can be measured from a PL are mutual intensities incident on the pupil weighted by the cross correlation of a pair of lantern modes. From numerically simulated lantern principal modes of a 6-port PL, we find that interferometric observables using a PL behave similarly to separated-aperture visibilities for simple models on small angular scales (<λ/D) but with greater sensitivity to symmetries and capability to break phase angle degeneracies. Furthermore, we present simulated observations with wave front errors (WFEs) and compare them to AMI. Despite the redundancy caused by extended lantern principal modes, spatial filtering offers stability to WFEs. Our simulated observations suggest that PLs may offer significant benefits in the photon-noise-limited regime and in resolving small angular scales at the low-contrast regime.

Elephant Trunk Inspired Multimodal Deformations and Movements of Soft Robotic Arms

AbstractElephant trunks are capable of complex, multimodal deformations, allowing them to perform task‐oriented high‐degree‐of‐freedom (DOF) movements pertinent to the field of soft actuators. Despite recent advances, most soft actuators can only achieve one or two deformation modes, limiting their motion range and applications. Inspired by the elephant trunk musculature, a liquid crystal elastomer (LCE)‐based multi‐fiber design strategy is proposed for soft robotic arms in which a discrete number of artificial muscle fibers can be selectively actuated, achieving multimodal deformations and transitions between modes for continuous movements. Through experiments, finite element analysis (FEA), and a theoretical model, the influence of LCE fiber design on the achievable deformations, movements, and reachability of trunk‐inspired robotic arms is studied. Fiber geometry is parametrically investigated for 2‐fiber robotic arms and the tilting and bending of these arms is characterized. A 3‐fiber robotic arm is additionally studied with a simplified fiber arrangement analogous to that of an actual elephant trunk. The remarkably broad range of deformations and the reachability of the arm are discussed, alongside transitions between deformation modes for functional movements. It is anticipated that this design and actuation strategy will serve as a robust method to realize high‐DOF soft actuators for various engineering applications.

Carbon Molecular Sieve Membranes with Ultra-Thin Selective Skin Layer by Pyrolysis of Porous Hollow Fibers.

Translating carbon molecular sieve (CMS) membranes into highly scalable hollow fiber geometry with ultra-thin selective layer (<1µm) for gas separation remains as great challenge. The porous support layer of precursor hollow fiber membranes is prone to collapse during pyrolysis, which induces thick skin layer (15-50µm) of CMS hollow fiber membranes. Here, a novel strategy is present to obtain an ultra-thin selective skin layer by carbonization of hollow fiber membranes with porous skin. P84-based defect-free CMS hollow fiber membranes with ultra-thin selective skin layer (0.9µm) for gas separation are prepared without any coating or complex chemical pretreatment. Compared with the carbon membranes derived from defect-free fibers, the H2 permeance (93.9 GPU) of CMS membranes derived from the porous fibers increases ≈1353% with comparable selectivity of H2/CH4 (143) and higher H2/N2 (120). Furthermore, the porous fibers are pre-aged near the Tg in N2 conditions before carbonization, and the H2 permeance of the derived CMS hollow fiber membranes reached 147 GPU (increased 2180%). It is a new facile way to prepare CMS hollow fiber membranes with ultra-thin selective layer by porous fibers, demonstrating its versatile potential in gas separation or organic liquids separation.

Numerical analysis of cascade lasing in Ho:ZBLAN fiber lasers with efficient output at ∼750 nm

Recent advances in blue-emitting laser diodes (LDs) have enabled visible laser operation in rare-earth-doped fluoride fibers. Therefore, investigation of the power scaling of visible fiber lasers enabled by direct blue diode pumping is significant. In this study, we numerically investigated the performance of a continuous-wave (CW) Ho:ZBLAN fiber laser operating at approximately 750 nm for the 5F4,5S2→5I7 transition using a cascade lasing process. Direct diode pumping at 450 nm is used in conjunction with double-clad fiber geometry. Simultaneous lasing for the mid-IR 5I7→5I8 transition effectively depopulated the 5I7 level and significantly enhanced efficiency and power scalability. A slope efficiency of 49% was associated with the calculated CW output power of 14.2 W at a launched pump power of 30 W. This study demonstrates the significance of depopulating the lower laser level in the development of an efficient Ho:ZBLAN 750 nm fiber laser and offers an alternative approach for developing high-power visible laser sources.

Extraction of volatile organic compounds liberated upon filament extrusion by 3D pen and its comparison with a desktop 3D printer using solid-phase microextraction fiber and Arrow

Desktop 3D printers that operate by the fused deposition modeling (FDM) mechanism are known to release numerous hazardous volatile organic compounds (VOCs) during printing, including some with potential carcinogenic effects. Operating in a similar manner to FDM 3D printers, 3D pens have gained popularity recently from their ability to allow users to effortlessly draw in the air or create various 3D printed shapes while handling the device like a pen. In contrast to numerous modern 3D printers, 3D pens lack their own ventilation systems and are often used in settings with minimum airflow. Their operation makes users more vulnerable to VOC emissions, as the released VOCs are likely to be in the breathing zone. Consequently, monitoring VOCs released during the use of 3D pens is crucial. In this study, VOCs liberated while extruding acrylonitrile butadiene styrene (ABS) filaments from a 3D pen were measured by solid-phase microextraction (SPME) combined with gas chromatography/mass spectrometry (GC/MS). SPME was investigated using the traditional fiber and Arrow geometries with the DVB/Carbon WR/PDMS sorbent while four different brands of ABS filaments—Amazon Basics, Gizmodork, Mynt 3D, and Novamaker—were used with the 3D pen. Heatmap analysis showed differentiation among these brands based on the liberated VOCs. The nozzle temperature and printing speed were found to affect the number and amount of released VOCs. This study goes a step further and presents for the first time a comparison between 3D pen and a desktop 3D printer based on liberated VOCs. Interestingly, the findings reveal that the 3D pen releases a greater number and amount of VOCs compared to the printer. The amounts of liberated VOCs, as indicated by the corresponding chromatographic peak areas, were found to be 1.4 to 62.6 times higher for the 3D pen compared to the 3D printer when using SPME Arrow.

Structural dependence of transmission characteristics for photonic crystal fiber with circularly distributed air-holes

Abstract In this study, design and transmission characteristics of a special type of photonic crystal fiber (PCF) geometry namely, circular-lattice photonic crystal fiber (C-PCF) structure are presented. The cladding of the structure consists by a cylindrically symmetrical distribution of air-holes in the silica background and the core is created by omitting one air-hole at the center. The structure provides high degree of flexibility in the fiber design and hence tailorable modal properties. Structural dependence of transmission characteristics of the geometry is numerically investigated by using finite difference mode convergence algorithm. The wavelength responses of fiber parameters, such as effective refractive index, chromatic dispersion, mode-effective area, and nonlinear coefficient of the structure are systematically investigated. Besides, effective V-parameter and single-mode operation of the fiber are also evaluated and discussed. The simulation results show the possibility of large negative dispersion and dispersion flattened nature of the geometry.

Topographically and Chemically Enhanced Textile Polycaprolactone Scaffolds for Tendon and Ligament Tissue Engineering.

The use of tissue engineering to address the shortcomings of current procedures for tendons and ligaments is promising, but it requires a suitable scaffold that meets various mechanical, degradation-related, scalability-related, and biological requirements. Macroporous textile scaffolds made from appropriate fiber material have the potential to fulfill the first three requirements. This study aimed to investigate the biocompatibility, sterilizability, and functionalizability of a multilayer braided scaffold. These macroporous scaffolds with dimensions similar to those of the human anterior cruciate ligament consist of fibers with appropriate tensile strength and degradation behavior melt-spun from Polycaprolactone (PCL). Two different cross-sectional geometries resulting in significantly different specific surface areas and morphologies were used at the fiber level, and a Chitosan-graft-PCL (CS-g-PCL) surface modification was applied to the melt-spun substrates for the first time. All scaffolds elicited a positive cell response, and the CS-g-PCL modification provided a platform for incorporating functionalization agents such as drug delivery systems for growth factors, which were successfully released in therapeutically effective quantities. The fiber geometry was found to be a variable that could be manipulated to control the amount released. Therefore, scaled, surface-modified textile scaffolds are a versatile technology that can successfully address the complex requirements of tissue engineering for ligaments and tendons, as well as other structures.

Evaluating Osteoporosis in Chronic Kidney Disease: Both Bone Quantity and Quality Matter.

Bone strength is determined not only by bone quantity [bone mineral density (BMD)] but also by bone quality, including matrix composition, collagen fiber arrangement, microarchitecture, geometry, mineralization, and bone turnover, among others. These aspects influence elasticity, the load-bearing and repair capacity of bone, and microcrack propagation and are thus key to fractures and their avoidance. In chronic kidney disease (CKD)-associated osteoporosis, factors traditionally associated with a lower bone mass (advanced age or hypogonadism) often coexist with non-traditional factors specific to CKD (uremic toxins or renal osteodystrophy, among others), which will have an impact on bone quality. The gold standard for measuring BMD is dual-energy X-ray absorptiometry, which is widely accepted in the general population and is also capable of predicting fracture risk in CKD. Nevertheless, a significant number of fractures occur in the absence of densitometric World Health Organization (WHO) criteria for osteoporosis, suggesting that methods that also evaluate bone quality need to be considered in order to achieve a comprehensive assessment of fracture risk. The techniques for measuring bone quality are limited by their high cost or invasive nature, which has prevented their implementation in clinical practice. A bone biopsy, high-resolution peripheral quantitative computed tomography, and impact microindentation are some of the methods established to assess bone quality. Herein, we review the current evidence in the literature with the aim of exploring the factors that affect both bone quality and bone quantity in CKD and describing available techniques to assess them.

Prospects and challenges for all-optical thermal management of fiber lasers

It is hard to overstate the utility of lasers in modern technology. Optical-fiber-based lasers are of particular value thanks to their combination of small form factors, afforded by the coilability of the thin strands of fiber, and high beam-quality output. The optical fiber geometry also possesses a relatively high surface-area-to-volume ratio, rendering thermal management somewhat more straightforward than in other bulk laser types. Regardless, the generation of heat during the lasing process can still be problematic for a myriad of reasons, and conventional methods of thermal management do not comport with the potential compactness and elegance of fiber lasers as technological solutions. This Perspective summarizes recent advances in glass science and optical fiber engineering to support the provocative premise that heat generation in future laser systems can be entirely managed by a combination of fiber materials and novel laser physics. Letting the fiber manage heat itself would have significant impacts on enhancing system performance while greatly reducing size, weight, power-consumption, and cost.

Using recycled plastic waste as fiber reinforcement on limestone residue mortar

The main purpose of the paper is to study the effect of the geometry of recycled plastic fiber on the performance of mortar basing on natural limestone residue. The used fibers were collected from plastic waste of polypropylene, resulting from domestic sweeps fabrication. Two types of recycled fibers were used, straight and crimped fibers, which have the same length (20 ± 2 mm) and the same diameter (0.45 ± 0.07 mm). Four dosages of fibers were considered, 0.5, 1, 1.5 and 2 wt. %. The obtained results show that the geometry of recycled plastic fibers has an important effect on the performances of limestone residue mortar. The addition of recycled fibers to mortar decreases its workability and the decrease is higher with crimped fibers. The results revealed that the limit dosage of recycled plastic fiber necessary to obtain a workable mortar is 1 % and 0.5 % for straight and crimped fibers, respectively. The benefit of recycled plastic fibers is well observed on the flexural and compressive behavior of limestone residue mortar, but the strength’s values are higher in straight fibers mortar (SFM) than that in crimped fibers mortar (CFM). The microstructure analysis confirms the good performances of the fiber mortar.

Bioprinting Cell-Laden Hydrogels for Studies of Epithelial Tissue Morphogenesis.

The extracellular matrix (ECM) provides dynamic structural and molecular signals that affect the form and function of developing tissues. In order to parse how the individual features of the ECM impact cell- and tissue-level behavior during development, engineered culture models should reproduce key structural and molecular features of native ECM. Here, we describe a protocol for bioprinting epithelial cell aggregates embedded within a collagen-Matrigel ink in order to study the dynamic interplay between epithelial tissues and aligned networks of type I collagen fibers. Collagen fiber alignment and geometry can be spatially controlled by modulating the printing speed, nozzle geometry, surface chemistry, and degree of molecular crowding in the printing ink. We provide detailed procedures for generating epithelial cell aggregates, microextrusion printing collagen-Matrigel bioinks, culturing the three-dimensional (3D)-printed tissues, and imaging 3D-printed collagen-Matrigel constructs.