Gas Electron Multiplier Research Articles

Charge amplification in sub-atmospheric CF4:He mixtures for directional dark matter searches

Low pressure gaseous Time Projection Chambers (TPCs) are a viable technology for directional Dark Matter (DM) searches and have the potential for exploring the parameter space below the neutrino fog [1,2]. Gases like CF4 are advantageous because they contain flourine which is predicted to have heightened elastic scattering rates with a possible Weakly Interacting Massive Particle (WIMP) DM candidate [3,4,5]. The low pressure of CF4 must be maintained, ideally lower than 100 Torr, in order to elongate potential Nuclear Recoil (NR) tracks which allows for improved directional sensitivity and NR/Electron Recoil (ER) discrimination [6]. Recent evidence suggests that He can be added to heavier gases, like CF4, without significantly affecting the length of 12C and 19F recoils due to its lower mass. Such addition of He has the advantage of improving sensitivity to lower mass WIMPs [1]. Simulations can not reliably predict operational stability in these low pressure gas mixtures and thus must be demonstrated experimentally. In this paper we investigate how the addition of He to low pressure CF4 affects the gas gain and energy resolution achieved with a single Thick Gaseous Electron Multiplier (ThGEM).

The multi-slit very small angle neutron scattering instrument at the China Spallation Neutron Source.

A multi-slit very small angle neutron scattering (MS-VSANS) instrument has been finally accepted at the China Spallation Neutron Source (CSNS). It is the first spallation neutron source based VSANS instrument. MS-VSANS has a good signal-to-noise ratio and can cover a wide scattering vector magnitude range from 0.00028 to 1.4 Å-1. In its primary flight path, a combined curved multichannel beam bender and sections of rotary exchange drums are installed to minimize the background downstream of the instrument. An exchangeable multi-slit beam focusing system is integrated into the primary flight path, enabling access to a minimum scattering vector magnitude of 0.00028 Å-1. MS-VSANS has three modes, namely conventional SANS, polarizing SANS and VSANS modes. In the SANS mode, three motorized high-efficiency 3He tube detectors inside the detector tank cover scattering angles from 0.12 to 35° simultaneously. In the polarizing SANS mode, a double-V cavity provides highly polarized neutrons and a high-efficiency 3He polarization analyser allows full polarization analysis. In the VSANS mode, an innovative high-resolution gas electron multiplier detector covers scattering angles from 0.016 to 0.447°. The absolute scattering intensities of a selection of standard samples are obtained using the direct-beam technique; the effectiveness of this method is verified by testing the standard samples and comparing the results with those from a benchmark instrument. The MS-VSANS instrument is designed to be flexible and versatile and all the design goals have been achieved.

Design validation of the CMS Phase-2 Triple-GEM detectors

The High-Luminosity LHC will deliverproton-proton collisions at 5.0–7.5 times the nominal LHC luminosity, with anexpected number of 140–200 pp-interactions per bunch crossing. To maintain the performance of muon triggering and reconstruction underhigh background, the forward part of the Muon spectrometer of the CMSexperiment will be upgraded with Gas Electron Multipliers (GEM) and improvedResistive Plate Chambers detectors. Particularly challenging isthe extension of the pseudorapidity of the muon system up to |η| < 2.8with a 6-layer station, named ME0, that will be installed behind the newhigh granularity calorimeter and that will see particle rates up to150 kHz/cm2 and integrate a dose of 250 krad by the end of the High Luminosity phase of the LHC.In this contribution we will present the major design changes of the Triple-GEMdetectors to adapt them for the harsh radiation environment and the highparticle rate. We shall summarize the performance of prototype Triple-GEMdetectors measured with X-rays and gamma at theCERN GIF++ irradiation facility.

Gas gains over 104 and optimisation using 55Fe X-rays in low pressure SF6 with a novel Multi-Mesh ThGEM for directional dark matter searches

The Negative Ion Drift (NID) gas SF6 has favourable properties for track reconstruction in directional Dark Matter (DM) searches utilising low pressure gaseous Time Projection Chambers (TPCs). However, the electronegative nature of the gas means that it is more difficult to achieve significant gas gains with regular Thick Gaseous Electron Multipliers (ThGEMs). Typically, the maximum attainable gas gain in SF6 and other Negative Ion (NI) gas mixtures, previously achieved with an 55Fe X-ray source or electron beam, is on the order of 103 [1,2,3,4]; whereas electron drift gases like CF4 and similar mixtures are readily capable of reaching gas gains on the order of 104 or greater [5,9,7,8,6]. In this paper, a novel two stage Multi-Mesh ThGEM (MMThGEM) structure is presented. The MMThGEM was used to amplify charge liberated by an 55Fe X-ray source in 40 Torr of SF6. By expanding on previously demonstrated results [10], the device was pushed to its sparking limit and stable gas gains up to ˜50000 were observed. The device was further optimised by varying the field strengths of both the collection and transfer regions in isolation. Following this optimisation procedure, the device was able to produce a maximum stable gas gain of ˜90000. These results demonstrate an order of magnitude improvement in gain with the NID gas over previously reported values and ultimately benefits the sensitivity of a NITPC to low energy recoils in the context of a directional DM search.

Design, construction, and performance of the GEM based radial time projection chamber for the BONuS12 experiment with CLAS12

A new radial time projection chamber based on Gas Electron Multiplier amplification layers was developed for the BONuS12 experiment in Hall B at Jefferson Lab. This device represents a significant evolutionary development over similar devices constructed for previous experiments, including cylindrical amplification layers constructed from single continuous GEM foils with less than 1% dead area. Particular attention had been paid to producing excellent geometric uniformity of all electrodes, including the very thin metalized polyester film of the cylindrical cathode. This manuscript describes the design, construction, and performance of this new detector.

The upgrade of the CMS muon system for the high luminosity LHC

The muon system of the CMS experiment is expected to upgrade all of its subdetectors for the Phase-2 of the Large Hadron Collider (LHC) that will begin in 2029. The upgrade plans for drift tubes (DTs), cathode strip chambers (CSCs) and resistive place chambers (RPCs) include a new electronics for better performance in high background rate conditions and to sustain the large radiation dose delivered by the high-luminosity LHC (HL-LHC). Two new RPC stations will also be installed to complement CSCs in the forward region 1.8 < |η| < 2.4, while three stations of triple-GEM (gas electron multiplier) detectors will complement CSCs in the region 1.5 < |η| < 2.4 and extend the CMS muon system coverage to the very forward pseudorapidity region 2.4 < |η| < 2.8. We present the goals and status of the CMS muon system upgrade including the performance of the early Phase-2 upgrades demonstrated in Run 3 with proton-proton collisions, the performance validation of the new detectors in test beams and the mass production status of the new stations.

Development of a Triple-GEM detector with strip readout and GEMINI chip for X rays and neutron imaging

Thermal neutron imaging can be a useful tool in the study of the internal structure of an object. The different attenuation properties of the materials with respect to X rays give rise to different interactions and the result is a complementary non-destructive analysis, which can provide important additional information. This technique has been successfully employed in different areas of work, especially in material science and cultural heritage studies. This paper describes the development of a new detection system and its characterization performed with X ray emissions. The system features the use of a gaseous detector, based on the Gas Electron Multiplier technology, and a fully digital electronic readout, with a combination of custom-made ASICs (called GEMINI) and FPGA boards, enabling fast single photon counting. The detector can be thus used directly for X ray imaging, while the addition of a suitable converter in its active volume will allow for detection of neutrons and for reconstruction of their tracks. The readout system is based on a x-y strip structure and features the reconstruction of single events through the center of mass methodology, allowing for accurate tomography, with sub-mm spatial resolution, in combination with sub-ms time resolution and high rate capabilities (up to MHz/mm2).

Analysis of discharge events in the CMS GE1/1 GEMdetectors in presence of LHC beam

In July 2022, the experiments installed on the Large Hadron Collider (LHC) accelerator ring started a new data taking phase, Run-3. Before this period, an upgrade campaign took place during the so called Long Shutdown 2 (2018–2022). In particular, the muon system of the CMS experiment has been upgraded with the installation of a new gas detector station, GE1/1, based on Gas Electron Multiplier technology (GEM). The CMS experiment has scheduled the installation of two additional GEM stations: GE2/1 and ME0. The aim of the GEM stations is to maintain the performance of the muon system, reached during the last data taking phase (Run-2), with the increase of instantaneous luminosity expected at the LHC. The installed GE1/1 station covers the pseudorapidity region 1.55 <|η|< 2.18. GE1/1 participated in the CMS Run-3 data taking from July to November 2022 and, in this period, its detectors were exposed for the first time to the radiation produced during the collisions of the LHC beams, with a center of mass energy of 13.6 TeV. Since the first days of Run-3, where only a few bunches collided in CMS, the GE1/1 detectors started to experience a significant number of discharges, affecting their smooth operation during the data taking. In this talk, we present an analysis of discharges, which started by simply counting the number of discharges occurring per detector. An interesting phenomenon observed was that the discharge rate can vary a lot among the installed detectors; this is due to the fact that the occurrence of discharges is driven by the manufacturing of the GEM foils used in the detectors. Imperfections in their manufacturing can lead to large variation in the discharge rate. In addition, the rate can vary in time, due to the fact that discharges can produce damage at the site generating them, deactivating a particular hole or, in the worst case, producing a short circuit in the GEM foil, deactivating a part of the foil amplification region. We present the evolution of the discharge rate in time and its dependence on the HV working point and on the luminosity delivered by the LHC beams. This contribution illustrates the actions taken to mitigate the discharge rate and to assure a smooth detector operation.

Cryogenic RPWELL: a novel charge-readout element for dual-phase argon TPCs

The first operation of a cryogenic Resistive Plate WELL (RPWELL) detector in the saturated vapor of liquid argon is reported. The RPWELL detector was composed of a Thick Gas Electron Multiplier (THGEM) electrode coupled to a metallic anode via Fe2O3/YSZ ceramics (Fe2O3 in weight equal to 75%), with tunable bulk resistivity in the range 109–1012 Ω·cm. The detector was operated at liquid argon temperature in saturated argon vapor (90 K, 1.2 bar) and characterized in terms of its effective charge gain and stability against discharges. Maximum stable gain of G≈17 was obtained, without discharges. In addition, preliminary results from novel 3D-printed thermoplastic plates doped with carbon nanotubes are presented.

An investigation of the simulation response of GEM-based detector for the fast neutrons by employment of GEANT4 & MCNP MC codes

The current work explores the potential ability to identify fast neutrons with one Gas Electron multiplier (GEM) detector connected to a polyethylene (PE) converter. Hence, a simulation was tested utilizing the GEANT4 Monte Carlo and MCNP simulation codes. The GEM detector functions by detecting the charged particles generated by an (n, p) reaction on a polyethylene. Fast neutrons in the ranging with energy levels of 1.0 MeV to to 25 MeV have the ability to travel towards the detector surface and evaluation was conducted from its response. For the 1 mm, 2 mm and 3 mm converter thickness, the sensitivity remains ∼ 9.8% and 13.4%, and 14.2% respectively via GEANT4 QGSP_BERT_HP physics lists. For the same converter thicknesses, sensitivity remains ∼ 9% and 12%, and 12.5% using the QGSP_BIC_HP physics list. Using the MCNP, with a 1 mm, 2 mm and 3 mm converter thickness, the sensitivity remains ∼ 12.8%, 13.3% and 13.6% via cell-flux tally method, while with the MCNP pulse- height technique with the same converter thicknesses, the sensitivity remains ∼ 10.6%, 12% and 13.3% respectively. The current findings reveals that GEM detector exhibits a clear and efficient response to inserted fast neutrons. Consequently, GEM based detectors have a potential to be a better candidate for fast neutron detection.

Erosion mechanisms of DLC coatings deposited on polyimide and silica substrates when exposed to a pulsed gas discharge

The influence of spark discharges on the surface morphology and chemical composition of resistive diamond-like carbon (DLC) coatings designed to prevent breakdowns in gas electron multipliers (GEMs) has been studied. DLC coatings with thicknesses of approximately 200 nm and 66 nm were deposited in an inert argon atmosphere on polyimide substrates by high current pulsed magnetron sputtering and on silica (silicon oxide) substrates by vacuum arc method. Based on the analysis of images of optical and scanning electron microscopy, it was established that, the region of interaction between the gas discharge channel and the coating surface presents an accumulation of erosion craters with a characteristic linear size in the range of 20–40 μm. The value of current density passing in the region of interaction between the plasma in spark discharges and the sample is estimated to be of the order of 105 A/cm2, which is sufficient to ablate the coating and create thermal stresses of magnitude ∼4 GPa at the interface between the coating and the substrate. Thus, pulsed surface erosion, insufficient adhesive strength of the coating to the substrate, and poor thermal conductivity should be considered as the key reasons for destruction of the DLC coating.

Electron transfer efficiency in liquid xenon across THGEM holes

Dual-phase liquid-xenon time projection chambers (LXe TPCs) deploying a few tonnes of liquid are presently leading the search for WIMP dark matter. Scaling these detectors to 10-fold larger fiducial masses, while improving their sensitivity to low-mass WIMPs presents difficult challenges in detector design. Several groups are considering a departure from current schemes, towards either single-phase liquid-only TPCs, or dual-phase detectors where the electroluminescence region consists of patterned electrodes. Here, we discuss the possible use of Thick Gaseous Electron Multipliers (THGEMs) coated with a VUV photocathode and immersed in LXe as a building block in such designs. We focus on the transfer efficiencies of ionization electrons and photoelectrons emitted from the photocathode through the electrode holes and show experimentally that efficiencies approaching 100% can be achieved with realistic voltage settings. The observed voltage dependence of the transfer efficiencies is consistent with electron transport simulations once diffusion and charging-up effects are included.

First Observation of Neutral Bremsstrahlung Electroluminescence in Liquid Argon.

A recent discovery of additional mechanism of electroluminescence (EL) in noble gases due to the neutral bremsstrahlung (NBrS) effect led to a prediction that NBrS EL should be present in noble liquids as well. A theoretical model of NBrS EL in noble liquids was developed accordingly in the frameworks of Cohen-Lekner and Atrazhev. In this work, we confirm this prediction: For the first time, visible-range EL has been observed in liquid argon at electric fields reaching 90 kV/cm, using gas electron multiplier (GEM) and thick GEM structures. Absolute light yields of the EL were measured and found to be in excellent agreement with the theory, provided that the momentum-transfer cross section of electron scattering is used for calculation of the NBrS cross section (instead of the energy-transfer one).

A Facility for Studying Gas Mixtures for a Three-Cascade Gas Electron Multiplier

A Facility for Studying Gas Mixtures for a Three-Cascade Gas Electron Multiplier

Combined Spectroscopy System Utilizing Gas Electron Multiplier and Timepix3 Technology for Laser Plasma Experiments

We present an innovative X-ray spectroscopy system to address the complex study of the X-ray emissions arising from laser–target interactions, where the emissions occur within extremely brief intervals from femtoseconds to nanoseconds. Our system combines a Gas Electron Multiplier (GEM) detector with a silicon-based Timepix3 (TPX3) detector. These detectors work in tandem, allowing for a spectroscopic radiation analysis along the same line of sight. With an active area of 10 × 10 cm2, the GEM detector allows for 1D measurements for X-ray energies (2–50 keV) by utilizing the full 10 cm gas depth. The high-energy part of the radiation beam exits through a downstream side window of the GEM without being absorbed in the gas volume. Positioned side-on at the GEM detector’s exit, the TPX3 detector, equipped with a pixelated sensor (55 µm × 55 µm; active area 14 mm × 14 mm), uses its full 14 mm silicon sensor to detect hard X-rays (50–500 keV) and gamma rays (0.5–10 MeV). We demonstrate the correct operation of the entire detection system and provide a detailed description of the Timepix3 detector’s calibration procedure, highlighting the suitability of the combined system to work in laser plasma facilities.

A novel technique for measuring position resolution of Gas Electron Multipliers (GEM)

Gas Electron Multiplier (GEM) detectors are widely used for tracking and imaging applications due to their excellent position resolution and high efficiency, among other factors. The present study aims to assess the position resolution by employing a novel method that utilizes a high-precision instrument for source movement. The results demonstrate that the double GEM can accurately determine positions with sigma values of up to 36.8 μm and 54.6 μm in the x and y directions, respectively. Additionally, other standard characterizations, such as energy resolution, gain uniformity, and charge spread, were evaluated experimentally and found to be consistent with existing literature. A Garfield simulation was also performed to validate the experimental charge spread results.

Impact of magnetic field on the stability of the CMS GE1/1 GEM detector operation

The Gas Electron Multiplier (GEM) detectors of the GE1/1 station of the CMS experiment have been operated in the CMS magnetic field for the first time on the 7th of October 2021. During the magnetic field ramps, several discharge phenomena were observed, leading to instability in the GEM High Voltage (HV) power system. In order to reproduce the behavior, it was decided to conduct a dedicated test at the CERN North Area with the Goliath magnet, using four GE1/1 spare chambers. The test consisted in studying the characteristics of discharge events that occurred in different detector configurations and external conditions. Multiple magnetic field ramps were performed in sequence: patterns in the evolution of the discharge rates were observed with these data. The goal of this test is the understanding of the experimental conditions inducing discharges and short circuits in a GEM foil.The results of this test lead to the development of procedure for the optimal operation and performance of GEM detectors in the CMS experiment during the magnet ramps. Another important result is the estimation of the probability of short circuit generation, at 68 % confidence level, p short HV OFF = 0.42-0.35 +0.94% with detector HV OFF and p short HV OFF < 0.49% with the HV ON. These numbers are specific for the detectors used during this test, but they provide a first quantitative indication on the phenomenon, and a point of comparison for future studies adopting the same procedure.

Correction of the baseline fluctuations in the GEM-based ALICE TPC

To operate the ALICE Time Projection Chamber in continuous mode during the Run 3 and Run 4 data-taking periods of the Large Hadron Collider, the multi-wire proportional chamber-based readout was replaced with gas-electron multipliers. As expected, the detector performance is affected by the so-called common-mode effect, which leads to significant baseline fluctuations. A detailed study of the pulse shape with the new readout has revealed that it is also affected by ion tails. Since reconstruction and data compression are performed fully online, these effects must be corrected at the hardware level in the FPGA-based common readout units. The characteristics of the common-mode effect and of the ion tail, as well as the algorithms developed for their online correction, are described in this paper. The common-mode dependencies are studied using machine-learning techniques. Toy Monte Carlo simulations are performed to illustrate the importance of online corrections and to investigate the performance of the developed algorithms.

The cryogenic RWELL: a stable charge multiplier for dual-phase liquid argon detectors

The operation of a cryogenic Resistive WELL (RWELL) in liquid argon vapor is reported for the first time. It comprises a Thick Gas Electron Multiplier (THGEM) structure coupled to a resistive Diamond-Like Carbon (DLC) anode deposited on an insulating substrate. The multiplier was operated at cryogenic temperature (90 K, 1.2 bar) in saturated argon vapor and characterized in terms of charge gain and electrical stability. A comparative study with standard, non-resistive THGEM (a.k.a LEM) and WELL multipliers confirmed the RWELL advantages in terms of discharge quenching – i.e. superior gain and stability.

Construction of gas electron multiplier tracker for the J-PARC E16 experiment

The gas electron multiplier tracker (GTR) was developed and constructed for the J-PARC E16 experiment. The GTR is capable of operating in a high-counting environment of up to 5kHz/mm2. Additionally, its design is optimized to minimize the material budget and maximize acceptance. With high-quality Gas Electron Multiplier (GEM) foils, eight modules composed of 24 chambers were constructed. The gain of each chamber was measured to be over 6000, satisfying the experimental specification. This study provides a comprehensive description of the detector, including its design, assembly procedure, and construction process.