Gas Chromatography-mass Spectrometry Determination Research Articles

Development of dispersive solid phase extraction method for the preconcentration of parathion ethyl as a simulant of nerve agent sarin from soil, plant and water samples prior to GC-MS determination.

In the presented study, an efficient and fast analytical method was developed for the determination of parathion ethyl as sarin simulant by gas chromatography-mass spectrometry (GC-MS). Dispersive solid phase extraction (DSPE) was performed to concentrate parathion ethyl from soil, plant and water samples. Reduced graphene oxide-iron (II, III) oxide (rGO-Fe3O4) nanocomposite was used as an adsorbent to collect the target analyte from the aqueous sample solutions. After the optimization of extraction/preconcentration parameters, optimum conditions for adsorbent amount, eluent type, mixing type/period, eluent volume and initial sample volume were determined as 15mg, acetonitrile, vortex/30s, 100 µL and 10mL, respectively. Under the optimum conditions, analytical performance of the developed DSPE-GC-MS method was evaluated in terms of limit of detection (LOD), limit of quantitation (LOQ) and dynamic range. Dynamic range, LOD and LOQ values were figured out to be 0.94-235.15µg/kg, 0.41µg/kg and 1.36µg/kg (mass based), respectively. Satisfactory percent recovery results (90.3-125% for soil, 93.5-108.7% for plant, 88.5-112.9% for tap water) were achieved for soil, plant and tap water samples which proved the accuracy and applicability of the developed method. It is predicted that the DSPE-GC-MS method can be accurately used for the detection of sarin in soil, plant and water samples taken from war territories.

Gas chromatography-mass spectrometry determination of nicotine and cotinine in urine: A study of the effect of passive smoking.

Recent data suggest that passive smoking has a risk comparable to active smoking. Passive smoking is considered dangerous in children and is suspected as a cause of asthma. However, some reports are opposing such claims, indicating the need for solid results and large-scale studies. This scientific work aims to develop a method for the determination of nicotine (NCOT) and major nicotine's metabolite cotinine (COT) in urine samples, using gas chromatography-mass spectrometry (GC-MS). Analysis was performed using a gas chromatograph Agilent Technologies 7890A with an MS 5975C inert XL, EI/CI MSD with Triple-Axis detector. For sample preparation, liquid-liquid extraction was applied after an optimization study with different extraction media. Eventually, 1 mL of dichloromethane was selected for the extraction of 0.5mL of urine. Suitable chromatographic conditions were found for the rapid and accurate determination of NCOT and COT. Injection of 2μL was performed using GC-MS, and selected ion monitoring (SIM) analysis was performed with the following ions (m/z): 162 (quantifier ion) and 84, 133, 161 qualifier ions for NCOT, and 176 (quantifier ion) and 98, 118, 119, 147 qualifier ions for COT. Nicotine-D4 (NCOT-D4) and cotinine-D3 (COT-D3) were used as internal standards with quantifier ions 101 and 166, respectively. The retention time (Rt) for NCOT was 7.557 min and 9.743 min for COT. The method was validated following international principles, assessing characteristics such as absolute recovery, carryover, linearity, specificity, selectivity, accuracy, precision, and stability. The method showed a linear dynamic range from 0.5 to 50 ng/mL, and the limits of detection and quantification were for both NCOT and COT 0.2 and 0.5 ng/mL, respectively. Validation results were found satisfactory.Finally, the method was applied to the analysis of 60 clinical pediatric samples obtained from Aristotle University's pediatric clinic to check for possible exposure to smoke. Concentration levels ranged between 0.5 and 16.2ng/mL for NCOT and between 1.0 and 25.1ng/mL for COT. A rapid, sensitive, accurate, and simple method was developed and used as a tool for the confirmation of passive smoking in children. It is the first method applied to the analysis of such samples belonging to nonsmokers of young age. The total runtime of the GC-MS analysis was short (20 min), and the pretreatment protocol was simple, giving the ability for analysis of a large number of samples on a daily routine basis.

Validation and Collaborative Studies of Headspace Gas Chromatography-Mass Spectrometry for Determination of 1,4-Dioxane in Cosmetic Samples

Abstract Background 1,4-Dioxane (1,4-D) is a byproduct of the synthesis of surfactants, typically found in some cosmetics products such as shampoo, toothpaste, and soap. The presence of 1,4-D in cosmetics products is limited to a certain amount since 1,4-D is classified as a probable human carcinogen. Objective This present study was intended to validate static headspace gas chromatography-mass spectrometry (HS GC-MS) for the determination of 1,4-D in cosmetics products. Methods The condition of HS and GC-MS was optimized to get the best condition for analysis of 1,4-D using 1,4-dioxane-d8 (1,4-D-d8) as internal standard (IS). The developed method was validated by evaluating the key performance characteristics, including specificity, linearity, limit of detection (LoD), limit of quantification (LoQ), accuracy, and precision. Results The results showed that HS GC-MS was specific since the peaks of the selected ion monitoring (SIM) mode could be separated and confirmed at m/z 88 and m/z 96 for 1,4-D and 1,4-D-d8, respectively. The method was linear over the concentration range of 0.1287–1.2875 µg/mL, with R2 > 0.999 and RSD residuals <2.0. A collaborative study was conducted on this method, with 10 participating laboratories from four countries. The outcome of this study was found to be accurate and precise, as evidenced by the excellent recoveries ranging from 94.6% to 102.1%, and with good reproducibility with RSD values ranging from 0.2 to 1.1%. The collaborative studies exhibited that all data reported by 10 participating laboratories in four countries were inliers without any extreme values observed either in mean or RSD values Conclusions HS GC-MS is found to be fit and suitable for the determination of trace level of 1,4-D in cosmetics products. Highlights The HS GC-MS method could be proposed as a standard method for quantitative analysis of 1,4-D in cosmetics products since the collaborative studies indicated that the developed method meet the requirement in “Guidelines for Collaborative Study Procedures to Validate Characteristics of a Method of Analysis.”

Optimization of an analytical method based on miniaturized matrix solid-phase dispersion combined with gas chromatography-mass spectrometry for the determination of bisphenols in mussel samples

In this study, a new method has been optimized to determinate nine bisphenols (BPs) in mussel samples. This approach is based on miniaturized matrix solid-phase dispersion combined with gas chromatography-mass spectrometry determination after trimethylsilylation with 99% N,O-Bis-(trimethylsilyl)trifluoroacetamide + 1 % trimethylchlorosilane. The optimization process investigated the derivatization (derivatizing agent volume, time and temperature) and sample preparation (C18 co-column packed and C18 dispersant agent amounts and elution volume) parameters. A second clean-up step was performed using EMR-Lipid cartridges in order to efficiently remove lipids from mussel, the optimized parameters were Captiva EMR-Lipid sorbent amount and elution volume. The whole method was validated and very good linearity (r2 > 0.99) was obtained. The recoveries (accuracy) at two concentration levels ranged from 51.2 to 109 % and the coefficients of variation (precision) were between 0.55 and 13 %. The limits of quantification were between 0.014 μg/Kg dry weight for BPM and 4.0 μg/Kg dry weight for BPS. The analytical procedure was applied to four mussel samples from Galician Rías. Except for one of four samples whose BPAF level was below the limit of quantification, all BPs were found in concentrations that ranged from 0.39 to 301 μg/Kg dry weight.

Method Development and Validation in Water Matrix Employing Tandem Mass Spectrometry: Quantitative Analysis of 76 Multiclass Pesticides in Groundwater Samples Collected from Delhi Ncr Region by Quechers Based Liquid-liquid Extraction Method

A miniaturized, QuEChERS based, liquid–liquid extraction method followed by tandem gas chromatography–mass spectrometry determination was developed and validated for 76 pesticide residues determination in water using European SANTE/11312/2021 guideline and monitored the 70 ground water samples collected from Delhi NCR, India region for the determination of pesticide residues. The accuracy, precision, specificity, linearity, recovery, repeatability, reproducibility, robustness, limit of detection and limit of quantification of the method were evaluated. Uncertainty measurement was calculated for each analyte. The samples were extracted with dichloromethane using liquid-liquid extraction process. Each Pesticide was optimized in terms of different MS parameters and chromatographic conditions by GC-MS/MS using Multiple Reaction Monitoring (MRM) mode. In linearity regression co-efficient (R2) value of each pesticide was determined in the range of 0.9856-0.9997. The percent average recoveries were found from 87.98—119.99 at 1, 5 and 10 LOQ spiking level. The method performance complied with the regulatory requirements, and thus, can be implemented. LOD and LOQ of the pesticides were found 10µg/L and 30µg/L respectively. Expanded Measurement of uncertainty of all pesticides was below ±50 percent of mean recovery value as per SANTE 11312/2021. Organophosphorous, fungicides, and pyrethroids were the group of pesticides most frequently found. In this study, 12 pesticides were found above the MRL (EEC Council Directive 1980/778/EEC). Additionally, dieldrin, which is now banned by law in India, was found in samples of ground water. The method provided a high throughput analysis of multi-class pesticides with satisfactory selectivity, sensitivity, accuracy, and precision.

Miniaturized Solid-Phase Microextraction Coupled with Gas Chromatography-Mass Spectrometry for Determination of Endocrine Disruptors in Drinking Water

Miniaturized Solid-Phase Microextraction Coupled with Gas Chromatography-Mass Spectrometry for Determination of Endocrine Disruptors in Drinking Water

Gas Chromatography-Mass Spectrometry (GC-MS) Determination of Bioactive components from Corallocarpus epigaeus L Rhizome.

Corallocarpus epigaeous L. plant belongs to the family Cucurbitaceae is widely distributed in tropical Africa, Persian Gulf region and India (Andhra Pradesh, Assam, Bihar, Gujarat, Karnataka, Kerala, Madhya Pradesh, Maharashtra, Punjab, Rajasthan, Tamil Nadu, Uttar Pradesh, and West Bengal). Ethno medical information suggests that the roots are used as Laxative and antihelminthic. Syphilitic rheumatism, Venereal complaints, and later stages of dysentery. Yet no further characteristic study has been conducted from alcoholic extract of this species, therefore in this present study we seek to identify and evaluate the bioactive compounds from the ethanolic extracts of Corallocarpus epigaeus L (root) by using the GCMS. Result of this research work reports twenty-six compounds. The identified bioactive components and correlated with the NIST Mass Spectrum Library. In conclusion, we seek to provide additional information and pharmacological information associated with this rhizome.

A novel multiwalled carbon nanotube–cyclodextrin nanocomposite for solid-phase microextraction–gas chromatography–mass spectrometry determination of polycyclic aromatic hydrocarbons in snow samples

Novel solid-phase microextractioncoatings based on the use of multiwalled carbon nanotube–cyclodextrin (MWCNT-CD) nanocomposites were developed for the determination of 16-priority polycyclic aromatic hydrocarbons at ultratrace levels in snow samples. The performance of both β- and γ-CD was tested to increase the detection capabilities towards the heaviest and most lipophilic compounds, i.e., five- and six-ring PAHs. To facilitate the interactions of MWCNTs with CDs, an oxidation procedure using both HNO3 and H2O2 was applied, obtaining superior results using MWCNTs-H2O2-γ-CD fiber. Detection and quantitation limits below 0.7 and 2.3 ng/L, RSD lower than 21%, and recoveries of 88(± 2)–119.8(± 0.4)% proved the reliability of the developed method for the determination of PAHs at ultratrace levels. The complexation capability of the γ-CD was also demonstrated in solution by NMR and fluorescence spectroscopy studies and at solid state by XRD analysis. Finally, snow samples collected in the ski area of Dolomiti di Brenta were analyzed, showing a different distribution of the 16 priority PAHs, being naphthalene, phenanthrene, fluoranthene, and pyrene the only compounds detected in all the analyzed samples.Graphical

Preventing Mislabeling: A Comparative Chromatographic Analysis for Classifying Medical and Industrial Cannabis.

Gas chromatography (GC) techniques for analyzing and determining the cannabinoid profile in cannabis (Cannabis sativa L.) are widely used in standard laboratories; however, these methods may mislabel the profile when used under rapid conditions. Our study aimed to highlight this problem and optimize GC column conditions and mass spectrometry (MS) parameters to accurately identify cannabinoids in both standards and forensic samples. The method was validated for linearity, selectivity, and precision. It was observed that when tetrahydrocannabinol (Δ9-THC) and cannabidiolic acid (CBD-A) were examined using rapid GC conditions, the resulting derivatives generated identical retention times. Wider chromatographic conditions were applied. The linear range for each compound ranged from 0.02 μg/mL to 37.50 μg/mL. The R2 values ranged from 0.996 to 0.999. The LOQ values ranged from 0.33 μg/mL to 5.83 μg/mL, and the LOD values ranged from 0.11 μg/mL to 1.92 μg/mL. The precision values ranged from 0.20% to 8.10% RSD. In addition, forensic samples were analyzed using liquid chromatography (HPLC-DAD) in an interlaboratory comparison test, with higher CBD and THC content than GC-MS determination (p < 0.05) in samples. Overall, this study highlights the importance of optimizing GC techniques to avoid mislabeling cannabinoids in cannabis samples.

Degradation dynamics of organophosphorus insecticides applied in stored soybean (Glycine max L.) during supervised trials.

During storage, soybean kernels can be attacked by insects, which are preventively controlled with insecticides. Information on the dissipation of insecticide residues is crucial to know their final concentrations in food and establish the waiting periods necessary for consumption without health risks, and to determine the minimum waiting period necessary to comply with national and international standards. The aims of this study were to quantify the residue levels of organophosphorus insecticides (dichlorvos, chlorpyrifos-methyl and pirimiphos-methyl) in stored soybean, establish the effect during the storage period, and model the dissipation dynamics. Insecticide residues in soybeans were analyzed at 2, 30, 60, 90 and 120 days after application. An analytical method based on QuEChERS extraction followed by gas chromatography mass spectrometry (GC-MS/MS) determination was validated, with mean recoveries of 82-105%, depending on the spiking levels. Residues decreased below 80% of the initial concentration at 60 days after application and below quantifiable levels at 120 days. Residues followed a pseudo-first-order dissipation dynamics [Ct = C0×exp(-k.t)], with the dissipation constant (k) and half-lives being 0.538 and 1.3 days for dichlorvos, 0.018 and 38.8 days for chlorpyrifos-methyl, and 0.023 and 30.1 days for pirimiphos-methyl, respectively. These results allow concluding that, at the recommended dosage, these insecticides are safe for use on soybean grains stored under standard conditions commonly nowadays used in Argentina.

Gas chromatography-mass spectrometry determination of polycyclic aromatic hydrocarbons in oil fried quail meat vs. rabbit meat

Gas chromatography-mass spectrometry determination of polycyclic aromatic hydrocarbons in oil fried quail meat vs. rabbit meat

Gas chromatography-mass spectrometry determination of polycyclic aromatic hydrocarbons in oil fried quail meat vs. rabbit meat

Gas chromatography-mass spectrometry determination of polycyclic aromatic hydrocarbons in oil fried quail meat vs. rabbit meat

Determination of Dichloromethane in Blood with Headspace Gas Chromatography and Gas Chromatography-Mass Spectrometry

To establish a method for qualitative determination of dichloromethane (DCM) in blood by gas chromatography-mass spectrometry (GC-MS) and quantitative determination of DCM in blood by headspace gas chromatography (HS-GC), and to provide reliable support for forensic examination and analysis of poisoning or deaths caused by DCM. 0.5 mL blood sample was collected, added into headspace vial with chloroform as the internal standard, and processed by heating at 65 °C and evacuation treatment. The intermediate gas in the headspace vial was analyzed by GC-MS for qualitative validation of the method and by HS-GC for quantitative validation of the method. The method was then applied in forensic case analysis. Qualitative validation of the examination method by GC-MS found that the chromatographic peak and mass spectral characteristic ions were specific in samples added with DCM, and that no interference was observed in the blank negative samples. The limit of detection (LOD) was 5 μg/mL. Quantitative method validation by HS-GC found that the chromatographic peak of DCM was well separated from those of eight other volatile compounds, with the resolution>1.5 in all cases; the lower limit of quantification (LOQ) was 20 μg/mL and good linearity was shown within the range of 20 and 1000 μg/mL, R>0.999; the intra-day test precision and inter-day test precision were good (relative standard deviation, or RSD<15% for both) and test accuracy was high (relative error, or δ<15%). With the method established in the study, DCM was detected successfully in the blood of two fatal cases caused by DCM poisoning, with the blood concentration being 470 μg/mL and 915 μg/mL, respectively. This method is shown to be a rapid, stable and accurate approach to the qualitative and quantitative forensic and toxicological analysis of DCM in blood in DCM poisoning cases or deaths caused by DCM.

Automated sample preparation and fast GC-MS determination of fatty acids in blood samples and dietary supplements.

The present research is focused on the optimization of an automatized sample preparation and fast gas chromatography-mass spectrometry (GC-MS) method for the analysis of fatty acid methyl esters (FAMEs) in blood samples and dietary supplements, with the primary objective being a significant reduction of the analysis time and, hence, an enhanced sample throughput. The mass spectrometer was operated in the scan/selected ion monitoring (SIM) acquisition method, thus enabling the obtainment of qualitative and (highly sensitive) quantitative data. The separation of FAMEs was obtained in about 11min by using a micro-bore column of dimensions 15m × 0.10mm ID × 0.10µm df with a polyethylene glycol stationary phase. The novelty of the research involves reducing analysis time by using the novel fast GC-MS method with increased identification reliability and sensitivity in a single chromatographic run. With regard to the figures of merit, linearity, accuracy, and limits of detection (LoD) and quantification (LoQ) were determined. Specifically, regression coefficients were between 0.9901 and 0.9996; the LoDs ranged from 0.05 to 1.02µgg-1 for the blood analysis method, and from 0.05 to 0.26mgg-1 in the case of the dietary supplement approach. With respect to LoQs, the values were in the ranges of 0.15-3.39µgg-1 and 0.15-0.86mgg-1 for blood and dietary supplements analysis methods, respectively. Accuracy was evaluated by analyzing certified reference materials (human plasma, fish oil).

Development of a Tube Plasma Ion Source for Gas Chromatography-Mass Spectrometry Analysis and Comparison with Other Atmospheric Pressure Ionization Techniques.

A tube plasma ionization (TPI) open-air source for gas chromatography-mass spectrometry (GC-MS) was developed. This source is based on an inverse low temperature plasma configuration where the pin inner electrode is applying the high voltage and the grounded electrode is the housing itself. The ionization possibilities were tested by using an EPA mix of priority contaminants, showing that 68% of the analytes could undergo both proton-transfer and charge-exchange reactions. The potential of using different discharge gases (He and Ar) to ionize the analytes and auxiliary gases (He, N2, O2, and synthetic air) to transport the ions toward the MS was carefully investigated. Additionally, the addition of water was also tested to show the different ionization trends in the TPI source. Finally, the ionization by TPI under both dry and wet conditions was compared with other gas-phase atmospheric pressure ionization sources showing TPI could ionize a wider range of compounds (97%) than atmospheric pressure chemical ionization (APCI, 95%) and atmospheric pressure photoionization (APPI, 87%). Besides, the detection capability of TPI was better than APCI and APPI, achieving instrumental limits of detection down to 3 fg on column, which demonstrates the great potential of this ionization source for GC-MS determinations.

Miniaturized solid-phase microextraction coupled with gas chromatography-mass spectrometry for determination of endocrine disruptors in drinking water.

A simple and rapid method based on miniaturized solid-phase microextraction (mini-SPME) followed by gas chromatography-mass spectrometry was developed to identify eight endocrine disruptors (atrazine, diethylstilbestrol, hexestrol, estrone, estradiol, ethinylestradiol, norgestrel, and megestrel) in drinking water samples. Extraction parameters was optimized and further analyses was performed using them. The optimum temperature for the determination of endocrine disruptors in water was 80°C; the optimum extraction and preincubation times were 60 and 20min, respectively. The studied linear range of endocrine disruptors was 10.0-1000μgmL-1. The limit of detection ranged from 0.020 to 0.087μgmL-1. The correlation coefficient (r2) was 0.96-0.99. This research introduces a novel method for detecting analytes at extremely low concentrations, as well as the possibility of combining several detection technologies to give high-accuracy qualitative and quantitative determination of endocrine disruptors in aqueous samples.

Application of gas flow headspace liquid phase micro extraction coupled with gas chromatography-mass spectrometry for determination of 4-methylimidazole in food samples employing experimental design optimization.

Background4-Methylimidazole (4-MeI) or 4-methyl-1H-imidazole, a slightly yellowish solid with molecular formula C4H6N2, is a heterocyclic compound which supposedly does not exist as a natural product and is formed when carbohydrates are heating with ammonium compounds. This compound is used in pharmaceuticals, agriculture and photography chemicals, dyes and pigments, and rubber manufacturing. In the present study, a simple and efficient sample preparation method designated gas flow headspace liquid phase microextraction (GF-HS-SDME) was employed for the extraction and preconcentration of 4-methylimidazole (4-MeI) from food and beverage samples, before its determination by gas chromatography-mass spectrometry.ResultTo investigate the optimal conditions for the extraction process in GF-HS-SDME method, factors affecting extraction, including selection of extraction solvent, vial volume, extraction solvent ratio, position of extracting solvent, drop volume, sample volume, stirring speed, temperature, extraction time, sample pH, ionic strength of the sample solution and gas flow rate were optimized by utilizing both one-variable-at-a-time method and Plackett–Burman design. The investigation of protocol was carried out by using a standard solution containing 100.0 μg L−1 of 4-MeI in deionized water.ConclusionIn this study, a simple and green analytical method based on GF-HS-SDME was proposed for the extraction and preconcentration of 4-MeI from foodstuffs, followed by GC–MS determination. The main advantage of this method is its high preconcentration factor and fastness due to the application of an inert gas stream during microextraction.Supplementary InformationThe online version contains supplementary material available at 10.1186/s13065-022-00823-z.

Occurrence and Removal of Triazine Herbicides during Wastewater Treatment Processes and Their Environmental Impact on Aquatic Life.

Wastewater treatment plants (WWTPs) represent a major point source for pesticide residue entry to aquatic environment and may threaten ecosystems and biodiversity in urban area. Triazine herbicides should be paid attention to for their ubiquitous occurrence in the environment and long-term residue. The present study aimed to quantify eleven compounds of triazine herbicides during wastewater treatment processes. The solid phase extraction and gas-chromatography mass spectrometry (GC-MS) determination method were developed to identify the target herbicides with approving sensitivity. The pollution levels, removal rates of eleven triazine herbicides along five different treatment stages in WWTP were investigated. The results showed that three herbicides including atrazine, simetryn and prometryn were detected. Their concentrations in influent were among 28.79 to 104.60 ng/L. Their total removal rates from influent to effluent were 14.92%, 10.79% and 4.41%, respectively indicating that they were difficult to be effectively remove during wastewater treatment. Regarding the negative impact of triazine herbicides discharged from WWTPs on downstream water quality and aquatic life, the environmental risks were assessed by calculating the Environmental Relevance of Pesticides from Wastewater Treatment Plants Index (ERPWI) and water cycle spreading index (WCSI). The risk assessment results denoted the possible high risks for atrazine and simetryn to alage, and simetryn concurrently posed a high risk for the daphnia, while prometryn was at medium risk to alage. Atrazine and simetryn in effluent posed high risk for algae, meanwhile, simetryn had high risk for Daphnia. These results suggested a possible threat to the aquatic environment, rendering in this way the ERPWI method as a useful assessment tool. Further extensive study is needed for atrazine and simetryn in order to better understand their migration mechanism in aquatic environment.

Metal-organic framework-based magnetic dispersive micro-solid-phase extraction for the gas chromatography–mass spectrometry determination of polycyclic aromatic compounds in water samples

A magnetic hybrid material based on the use of the mixed-ligand Metal-Organic Framework (MOF) PUM198 is proposed for the magnetic dispersive micro solid-phase extraction (MD-μSPE) of the 16 polycyclic aromatic hydrocarbons (PAHs) included in the US-EPA priority pollutants list. PUM198 is a thermally robust MOF characterized by a doubly interpenetrated microporous framework in which Zn2+ ions and carboxylate groups define 2D planes that are pillared by a bis-pyridine-bis amide ligand containing a biphenyl scaffold. PUM198 revealed to be ideal to adsorb PAHs efficiently through non-covalent interactions. A Plackett-Burman Design followed by a Central Composite Design and the multicriteria method of the desirability functions were applied to find the optimal conditions for the extraction of the investigated PAHs, resulting in a reduced solvent consumption, i.e., 50 μL of solvent per extraction for 5 mL of sample, approximatively 3–20 times lower than those reported in previous studies, thus satisfying the principles of green analytical chemistry. Method validation proved the reliability of the method for the determination of PAHs at trace level, obtaining detection limits in the 6.7–27 ng/L range, good precision with RSDs% lower than 19% and recovery rates in the 99 (±13)–126 (±8)% range near the quantitation limit. Finally, the applicability of the method was demonstrated by analyzing underground water samples taken from contaminated sites

Highly efficient dispersive liquid-liquid microextraction assisted by magnetic porous carbon composite-based dispersive micro solid-phase extraction for determination of tramadol and methadone in urine samples by gas chromatography-mass spectrometry

The recognition of opioids, either as prescription drugs or illicit narcotics, is one of the hot challenges in the analytical field, especially in forensic medicine. Here, a rapid and high efficient air-assisted dispersive liquid-liquid microextraction (DLLME) running after a dispersive magnetic solid-phase extraction (MSPE) is developed for simultaneous extraction and preconcentration of tramadol and methadone in urine samples prior to gas chromatography-mass spectrometry (GC–MS) determination technique. The samples were first mixed with a new magnetic and porous adsorbent, based on a metal-organic framework (MOF) derived NH2-functionalized Fe3O4 nanoparticles-carbon nanocomposite (NH2-Fe3O4@C). Then, the eluent, containing the retrieve analytes, was directly applied as the disperser solvent, along with dichloromethane extracting solvents, to perform DLLME. The combination of MSPE, using the new high surface area sorbent, with a high-performance DLLME resulted in exceptional enrichment factors and extraction recoveries. Under the optimized conditions, linear ranges of 0.1–30 ng mL−1 and 0.1–35 ng mL−1, and detection limits of 73 and 32 pg mL−1, were obtained for tramadol and methadone, respectively. The developed system was utilized for the extraction and preconcentration of tramadol and methadone in some urine samples of suspected drug users, with a reasonable reproducibility (2.4–4.5%). The results were in good agreement with those of the official HPLC/MS-MS technique.