Gamma-ray Irradiation Research Articles

Aging Behavior of Polypropylene as Cable Insulation Under Gamma-Ray Irradiation

Aging Behavior of Polypropylene as Cable Insulation Under Gamma-Ray Irradiation

Dielectric Properties of Cross-Linked Polypropylene by Gamma-Ray Irradiation for Film Capacitor

Dielectric Properties of Cross-Linked Polypropylene by Gamma-Ray Irradiation for Film Capacitor

Experimental measurements of gamma-radiation effects on fiber-optic cables

This paper reports on our study of the effect of gamma-ray irradiation on two types of experimental fiber-optic cables. The first type of cable, CTFS, had a jelly-filling compound, whereas the second type, CTDS, was without the jelly. The cables contained three multi-mode (A, B, C) and five single-mode (D, E, F, G, H) optical fibers. The study was performed using two gamma-irradiation facilities with 60Co sources for slow long-term irradiation with the dose of 80.5 kGy at the low dose rate of 5.5 Gy/h and with the dose of 65.5 kGy at the higher dose irradiation rate of 0.94 kGy/h. After the irradiation with the dose of 80.5 kGy, the C fiber in the CTDS cable had the optical loss of 5.91 dB; 140 days after the gamma treatment at the wavelength of 1300 nm, it was 4.96 dB. The lowest optical losses for a single-mode fiber after irradiation with the dose of 65.5 kGy were found for the D fiber in the cable CTFS, namely 3.26 dB at 1490 nm and 3.49 dB at 1310 nm. In the fiber E in the CTDS cable, the optical loss was 3.62 dB at 1550 nm. In the fiber F in the CTDS cable, it was 3.86 dB at 1310 nm.

Effects of Gamma-ray and neutron irradiation on infrared optical properties of ZnSe and ZnS for ITER divertor thermography

Gamma-ray and neutron irradiation tests were performed by using antireflective-coated and non-antireflective-coated samples of ZnSe and ZnS to examine the impact on their infrared optical properties. In neutron irradiation tests, ZnSe and ZnS samples showed minimal transmittance reduction even up to 1.44 × 1016 n/cm2 (evaluated by dpa value, the values are 5.77 × 10−6, 2.07 × 10−5 for ZnSe and ZnS, respectively), about 5.8 times higher than the expected neutron fluence in ITER. Gamma irradiation at 100 kGy did not affect any of the samples, however, at 5.6 MGy (2.6x the expected dose of ITER), non-antireflective-coated ZnSe and ZnS exhibited induced absorption bands. Antireflective coating did partially mitigate this effect, but ZnS, even with antireflective coating, showed up to 2.5 % degradation over the wide wavelength range of 1.5–4.5 µm, whereas ZnSe was less affected. Both ZnSe and ZnS exhibited a modest 2 % absorption around 3 µm. Surface analysis by SEM, laser microscope, and XPS linked the 3-µm degradation to gamma-irradiation-induced Zn(OH)2 formation that was confined to the surface. Thus, transmittance degradation of ZnSe over the lifespan of ITER was estimated to be a maximum of approximately 7.8 %. The practical use of ZnSe in the IRTh system requires further evaluation with Si and CaF2 lenses and for the optical design to be finalized. Nevertheless, these findings suggest that ZnSe is a promising candidate for the IRTh system's lenses.

Sm2O3 micron plates/B4C/HDPE composites containing high specific surface area fillers for neutron and gamma-ray complex radiation shielding

In this study, a series of Sm2O3 micron plates/B4C/HDPE composites composed of synthesized Sm2O3 fillers (Sm2O3 micron plates) are prepared for shielding neutron and gamma radiation. The influence of micromorphology of Sm2O3 fillers on neutron and gamma radiation shielding properties of composites is investigated in detail. The XRD pattern reveals that the phase of synthetic Sm2O3 is cubic crystal systems, body-centered cubic lattices, and its space group is Ia 3‾ (206). SEM images and BET analyses reveal that the micromorphology of synthesized Sm2O3 is micron plates. The BET-specific surface area of the Sm2O3 fillers is increased with addition of urea content. The differential scanning calorimetry (DSC) curves reveal that Sm2O3 fillers increase the melting temperature of the composites, which is up to 138.6 °C. The thermogravimetric analysis (TGA) results reveal that the initial thermal degradation temperatures of the composites are all above 440 °C. The neutron and gamma radiation shielding tests show that Sm2O3 fillers with high BET-specific surface area (8.20 m2/g) and uniform size improve the neutron and gamma shielding rate of composites. A superior composite containing 10 wt% Sm2O3 (R = 1:25, R value represents the molar ratio of rare earth elements to urea)/20 wt% B4C/70 wt% HDPE has a neutron radiation shielding rate of 98.7% with a thickness of 15 cm under the 252Cf neutron source and a gamma radiation shielding rate of 72.1% with a thickness of 15 cm under 137Cs gamma source. And these lead-free and environment-friendly composites can be widely used in the neutron and gamma complex radiation fields.

Characterization of a New Citrus Mutant Induced by Gamma Irradiation with a Unique Fruit Shape, Gwonje-Early, and Determination of Specific Selection Markers Using Allele-Specific PCR

Gamma-ray irradiation is one of the most widely used mutagens worldwide. We previously conducted mutation breeding using gamma irradiation to develop new Citrus unshiu varieties. Among these mutants, Gwonje-early had an ovate shape, a protrusion of the upper part of the fruit, and a large fruit size compared with wild-type (WT) fruits. We investigated the external/internal morphological characteristics and fruit sugar/acid content of Gwonje-early. Additionally, we investigated genome-wide single-nucleotide polymorphisms (SNPs) and insertion/deletion (InDel) variants in Gwonje-early using whole-genome re-sequencing. Functional annotation by Gene Ontology analysis confirmed that InDels were more commonly annotated than SNPs. To identify specific molecular markers for Gwonje-early, allele-specific PCR was performed using homozygous SNPs detected via Gwonje-early genome re-sequencing. The GJ-SNP1 and GJ-SNP4 primer sets were effectively able to distinguish Gwonje-early from the WT and other commercial citrus varieties, demonstrating their use as specific molecular markers for Gwonje-early. These findings also have important implications in terms of intellectual property rights and the variety protection of Gwonje-early. Our results may provide insights into the understanding of morphological traits and the molecular breeding mechanisms of citrus species.

Radioprotective effectiveness of a novel delta-tocotrienol prodrug on mouse hematopoietic system against 60Co gamma-ray irradiation through inducing granulocyte-colony stimulating factor production

Considering the increasing risk of nuclear attacks worldwide, the development of develop potent and safe radioprotective agents for nuclear emergencies is urgently needed. γ-tocotrienol (GT3) and δ-tocotrienol (DT3) have demonstrated a potent radioprotective effect by inducing the production of granulocyte-colony stimulating factor (G-CSF) in vivo. However, their application is limited because of their low bioavailability. The utilization of ester prodrugs can be an effective strategy for modifying the pharmacokinetic properties of drug molecules. In this study, we initially confirmed that DT3 exhibited the most significant potential for inducing G-CSF effects among eight natural vitamin E homologs. Consequently, we designed and synthesized a series of DT3 ester and ether derivatives, leading to improved radioprotective effects. The metabolic study conducted in vitro and in vivo has identified DT3 succinate 5b as a prodrug of DT3 with an approximately seven-fold higher bioavailability compared to DT3 alone. And DT3 ether derivative 8a were relatively stable and approximately 4 times more bioavailable than DT3 prototype. Furthermore, 5b exhibited superior ability to mitigate radiation-induced pancytopenia, enhance the recovery of bone marrow hematopoietic stem and progenitor cells, and promote splenic extramedullary hematopoiesis in sublethal irradiated mice. Similarly, 8a shown potential radiation protection, but its radiation protection is less than DT3. Based on these findings, we identified 5b as a DT3 prodrug, and providing an attractive candidate for further drug development.

Effects of chemical treatment and gamma-ray irradiation on the structure-properties of sunn hemp and okra hessian cloth reinforced high-density polyethylene composites: A comparative study

Okra hessian cloth and Sunn hemp hessian cloth were prepared and treated with 5, 10, and 15 wt% alkali solutions for 1 h. The optimized concentration of alkali is 10 wt%. The untreated and treated hessian cloths reinforced high-density polyethylene (HDPE) composites were then prepared using the compression molding method. Alkali-treated, and 55 wt% fiber contents reinforced composites showed improved mechanical properties among 40, 45, 50, 55, 60, and 65 wt% fiber contents composites. 55 wt% fiber contents reinforced composites were then irradiated under gamma-ray at doses 2.5–7.5 kGy at the rate of 6 kGy/h. According to the X-ray diffraction analysis results, only alkali-treated Okra reinforced, and Sunn hemp-reinforced HDPE composites had higher crystallinity values than untreated and irradiated composites. Surface micrographs showed that the Okra-HDPE and Sunn hemp-HDPE had better matrix and fiber attachment. Cross-linking between the two varieties of fibers and matrix was seen using Fourier-transform infrared (FTIR) spectroscopy. Both irradiated composites exhibited greater hydrophobicity in their water intake characteristics compared to untreated and alkali-treated composites. The tensile strength ( TS) value of Sunn hemp composite for 5 kGy gamma-ray irradiation dose is 68 MPa, which is 14% and 42% higher than that of treated and untreated composites, respectively. For comparison, the TS value for 5 kGy dose irradiated Okra composite is 66 MPa, which is 17% and 44% higher than that of treated and untreated composites, respectively. Young’s modulus ( Y) values of irradiated Okra composite and irradiated Sunn hemp composite showed higher values than that of other composites. Both irradiated composites have better thermal and structural characteristics than untreated and alkali-treated composites.

A new ductile, tougher resin for impregnation of superconducting magnets

A major remaining challenge for Nb3Sn high field magnets is their training due to random temperature variations in the coils. The main objective of our research is to reduce or eliminate it by finding novel impregnation materials in replacement of the epoxies currently used. An organic olefin-based thermosetting dicyclopentadiene resin, C10H12, commercially available in Japan as TELENE® by RIMTEC, was used to impregnate a short Nb3Sn undulator coil developed by ANL and FNAL. This magnet reached short sample limit after only two quenches, compared with ∼100 when CTD-101K® was used. Ductility, i.e. the ability to accept large strains, and toughness were identified as key properties to achieve these results. In addition, we have been investigating whether mixing TELENE with high heat capacity ceramic powders such as Gd2O3, Gd2O2S, and HoCu2, increases the specific heat (Cp ) of impregnated Nb3Sn superconducting magnets. The viscosity, heat capacity, thermal conductivity, and other physical properties of TELENE with high-Cp powder fillers were measured in this study as a function of temperature and magnetic field. The TELENE-87 wt%Gd2O2S had a peak in Cp between 4.3 K and 5.3 K at fields between 0 and 8 T. We have also investigated the effect on the mechanical properties of pure and mixed TELENE under 10 MGy of gamma ray irradiation at the Takasaki Advanced Radiation Research Institute in Takasaki, Japan. TELENE-87 wt%Gd2O2S exhibited exceptional radiation resistance. Impregnating an undulator coil with TELENE mixed with Gd2O2S powder will verify whether the coils’ thermal stability further improves, or whether its low diffusivity will require engineering the material with high-thermal conductivity components. Short magnet training will lead to better magnet reliability, lower magnet margins, lower risk and substantial saving in accelerators’ commissioning costs. Part of this study is supported by the U.S.-Japan Science and Technology Cooperation Program in high energy physics operated by MEXT in Japan and DOE in the U.S.

Degradation behavior of DLC thin film under gamma-rays irradiation using molecular dynamics simulation

γ-rays have high energy, thus, when irradiated on the materials, lead to the degradation process of the materials which means the durability and efficiency of the system decrease. Therefore, analysis of the effect of γ-rays on the materials is important, despite this, little work has so far been undertaken to predict the irradiation effect. Furthermore, because the previous theoretical equations have many assumptions, the accuracy of the prediction is low. For these reasons, molecular dynamics simulation was used to analyze and predict the effect of γ-rays on the DLC thin film in this study. This study investigates the degradation process, bond distribution, and radical creation during γ-rays irradiated on the DLC thin film. The primary knock-on atoms (PKA) method was applied which can be mimicked first excited atoms by γ-rays. Also, to analyze the chemical change of the irradiated DLC, ReaxFF potential was selected. The dose rate condition covered various environments where the γ-rays were irradiated such as space, nuclear, medical, etc. The degradation mechanisms of DLC were different by the dose rate. For low dose rate conditions, the energy of excited atoms was converted by physical collisions between atoms. However, in the case of high dose rate conditions, radical production rapidly increased, resulting in physical and chemical energy dissipation. Within this paper, we present a fundamental numerical analysis of the degradation process that combines the PKA method and MD simulation to achieve improved accuracy. These findings could provide fundamental insight into the degradation phenomenon of surface-protective coatings for various applications with γ-ray irradiation environment.

Diversity induction with gamma-ray irradiation on Phalaenopsis amboinensis var. Common natural orchid generation M1V0

Phalaenopsis is a popular genus in the Orchidaceae family. Phalaenopsis amboinensis orchid is an endangered natural orchid, so it needs to be preserved. Conservation of natural orchid Phalaenopsis amboinensis var. Common way is by increasing genetic diversity. This research aims to determine the characteristics and morphological diversity of Phalaenopsis amboinensis natural orchid irradiated gamma-ray results and without gamma-ray irradiation; this research was conducted in two places: the implementation of gamma-ray irradiation at the PAIR-BATAN Laboratory and in Matesih, Karanganyar with an average height of 450 m above sea level. The research was conducted from December 2022 to May 2023. The study used a simple design of one factor, the doses of gamma-ray irradiation with 5 levels: 0 Gy (R0), 7.5 Gy (R1), 15 Gy (R2), 22.5 Gy (R3), 30 Gy (R4). Each treatment contained five accessions. So, there are 25 experimental units. Observational data were analyzed descriptively by comparing observational data from Phalaenopsis amboinensis var. Common Generation M1V0 orchids irradiated with control plants. The results showed diversity in the morphology of the Phalaenopsis amboinensis var. Common orchid Generation M1V0 results from gamma-ray irradiation based on qualitative morphology with phenotypic observations, showing two orchid leaf shapes: oblanceolate and elliptic. There are accessions with fasciated root conditions.

Improving Properties of Tungsten Oxide Films by Gamma Ray Irradiation

The deposition process and investigation of the physical properties of tungsten trioxide (WO3) thin films before and after gamma irradiation are presented in this paper. The WO3 thin films were deposited, using the pulse laser deposition technique, on glass substrates at laser energies of 600mJ and 800mJ. After deposition, the samples were gamma irradiated with Co60. The structural and optical properties of polycrystalline WO3 thin films are presented and discussed before and after 5kGy gamma irradiation at the two laser energies. X-ray diffraction spectra revealed that all the films consisted of WO3 crystallized in the triclinic form; the dislocation density and lattice strain increased with the absorbed dosage of gamma irradiation. The optical constants, the average diameter and the surface roughness of the WO3 films were calculated before and after gamma irradiation and for the two laser energies. It was found that the WO3 thin films conductivity increased by γ-irradiated and with the increase of the laser energy.

The impact of chemical treatment and gamma-ray irradiation on the okra hessian cloth reinforced high-density polyethylene composites

Okra hessian cloth-reinforced high-density polyethylene (HDPE) thermoplastic composites were prepared and characterized with both raw and alkali-treated fibers. The fiber contents were optimized for both the raw Okra thermoplastic composites and the alkali-treated Okra thermoplastic composites, and the optimum value of fiber content was 55 wt%. Samples that were alkali-treated and had 55 wt% fibers were subsequently exposed to gamma radiation at doses of 2.5, 5, and 7.5 kGy. Only the sample subjected to 5 kGy showed improved performance. Treated composites exhibited higher crystallinities than the untreated samples as observed by X-Ray diffraction analysis. The rupture surface micrographs of the composites exposed to 5 kGy gamma radiation revealed more compact than others. By using Fourier transform infrared spectroscopy analysis of composites, it was found that 5 kGy dose sample showed enhanced cross-linking between Okra fibers and HDPE matrix. The irradiated composite showed less water intake than the alkali-treated samples. Composites subjected to 5 kGy gamma rays showed improved tensile strength and Young’s modulus of values 66 MPa and 1925 MPa, respectively. Compared to raw and treated composites, the irradiated composites with a radiation dose of 5 kGy showed improved structural, mechanical, and thermal properties.

Evolution of the structure and tribological behavior of the organic coatings under gamma-ray irradiation

More reliable and long-term irradiation stability is essential for lubrication protection materials that served in nuclear energy equipment. In this paper, three typical commercially organic bonded solid lubricating coatings were chosen to investigate the influence of gamma (γ)-ray irradiation on microstructure and tribological behaviors. The evolution of microstructure and the changes of tribological properties for these coatings after irradiation were comparatively studied in detail. The results revealed that the crystallinity of the molybdenum disulfide (MoS2) lubricating phase was improved and were partial oxidized in the coatings after γ-ray irradiation, resulting in the surface roughness of the coating with MoS2 as the solid lubricating phase decreased significantly. The polytetrafluoroethylene (PTFE) lubricating phase was degraded from the long chains structure to smaller molecules after γ-ray irradiation. The results of tribological properties of the three coatings after γ-ray irradiation indicated that, for polyamide-imide-based lubricating coatings, the friction coefficient is decreased and the wear rate is increased after irradiation. For phenolic epoxy-based lubricating coating, the cross-linking effect of γ-ray irradiation predominated to improve the wear resistance and prolong the wear life of the coating. But overall, the influence of irradiation on tribological properties of three polymer-based coatings could almost be neglected duo to the changes of the microstructure in nanoscale. This work provides path and direction for design and preparation of the lubricating coatings that served in a nuclear reactor.

Efficient Gamma Ray Detection Using CdTe/CdS Core/Shell Quantum Dots: A Simple and Rapid Fluorescence Approach.

Gamma rays, as hazardous nuclear radiation, necessitate effective and rapid detection methods. This paper introduces a low-cost, fast, and simple fluorescence method based on CdTe/CdS core/shell quantum dots for gamma-ray detection. CdTe/CdS quantum dots, subjected to gamma irradiation from a 60Co source under various conditions, were investigated to assess their fluorescence sensor capabilities. The obtained results showed that an increase in CdTe/CdS nanoparticle size was associated with decreased sensitivity, while a reduction in CdTe/CdS concentration correlated with increased sensitivity. To further validate the practicality of CdTe/CdS core/shell quantum dots in gamma-ray detection, the structural properties of the quantum dots were meticulously studied. Raman spectroscopy, X-ray diffraction (XRD), and Fourier-transform infrared (FT-IR) analysis were conducted before and after gamma-ray radiation. The results demonstrated the crystalline stability of CdTe/CdS core/shell quantum dots under gamma irradiation, highlighting their robust structural integrity. In conclusion, the experimental findings underscore the exceptional potential of CdTe/CdS quantum dots as an off-fluorescence probe for simple, low-cost, fast, and on-site detection of gamma rays. This research contributes to the advancement of efficient and practical methods for gamma-ray sensing in various applications.

Mechanism underlying the rapid growth of Phalaenopsis equestris induced by 60Co-γ-ray irradiation.

Gamma (γ)-ray irradiation is one of the important modern breeding methods. Gamma-ray irradiation can affect the growth rate and other characteristics of plants. Plant growth rate is crucial for plants. In horticultural crops, the growth rate of plants is closely related to the growth of leaves and flowering time, both of which have important ornamental value. In this study, 60Co-γ-ray was used to treat P. equestris plants. After irradiation, the plant's leaf growth rate increased, and sugar content and antioxidant enzyme activity increased. Therefore, we used RNA-seq technology to analyze the differential gene expression and pathways of control leaves and irradiated leaves. Through transcriptome analysis, we investigated the reasons for the rapid growth of P. equestris leaves after irradiation. In the analysis, genes related to cell wall relaxation and glucose metabolism showed differential expression. In addition, the expression level of genes encoding ROS scavenging enzyme synthesis regulatory genes increased after irradiation. We identified two genes related to P. equestris leaf growth using VIGS technology: PeNGA and PeEXPA10. The expression of PeEXPA10, a gene related to cell wall expansion, was down-regulated, cell wall expansion ability decreased, cell size decreased, and leaf growth rate slowed down. The TCP-NGATHA (NGA) molecular regulatory module plays a crucial role in cell proliferation. When the expression of the PeNGA gene decreases, the leaf growth rate increases, and the number of cells increases. After irradiation, PeNGA and PeEXPA10 affect the growth of P. equestris leaves by influencing cell proliferation and cell expansion, respectively. In addition, many genes in the plant hormone signaling pathway show differential expression after irradiation, indicating the crucial role of plant hormones in plant leaf growth. This provides a theoretical basis for future research on leaf development and biological breeding.

Impact of gamma irradiation on physico-chemical and electromagnetic interference shielding properties of Cu2O nanoparticles reinforced LDPE nanocomposite films

In the current work, cuprous oxide (Cu2O) nanoparticles coated with Tween 80 were successfully synthesized via the chemical reduction method. Nanocomposites composed of low-density polyethylene (LDPE) and different ratios of Cu2O nanoparticles were fabricated by the melt mixing process. 10% of ethyl vinyl acetate (EVA) as a compatibilizing agent was added to the molten LDPE matrix and the mixing process continued until homogenous nanocomposites were fabricated. To study the influence of ionizing radiation on the fabricated samples, the prepared species were exposed to 50 and 100 kGy of gamma rays. The synthesized Cu2O nanoparticles were investigated by transmission electron microscopy (TEM) and X-ray diffraction (XRD). XRD and TEM analysis illustrated the successful formation of spherical Cu2O nanoparticles with an average size of 16.8 nm. The as-prepared LDPE/Cu2O nanocomposites were characterized via different techniques such as mechanical, thermal, morphological, XRD, and FTIR. Electromagnetic interference shielding (EMI) of the different nanocomposite formulations was performed as a promising application for these materials in practical life. The electromagnetic shielding effectiveness (SE) of the produced samples was measured in the X-band of the radio frequency range from 8 to 12 GHz using the vector network analyzer (VNA) and a proper waveguide. All the samples were studied before and after gamma-ray irradiation under the same conditions of pressure and temperature. The shielding effectiveness increased significantly from 25 dB for unirradiated samples to 35 dB with samples irradiated with 100 kGy, which reflects 40% enhancement in the effectiveness of the shielding.

Comparison of effects from gamma, e-beam and X-ray radiation on multilayer polymer films used in biopharmaceutical devices by chemometric treatment of spectroscopic data

The present study investigated the effects of gamma-ray, electron beam, and X-ray radiation on polymers in EVA/EVOH/EVA multilayer films. Spectroscopic methods, including FTIR and UV–Vis, were employed in conjunction with chemometric treatments such as PCA, SIMPLISMA treatments, and PLS models. The feasibility of dose prediction on multilayer film, given a known dose, is attainable across various irradiation technologies. Both gamma ray and X-ray exhibit comparable effects on the multilayer film, and it is feasible to anticipate the dose released on the film by utilizing UV–Vis spectra or infrared spectra for gamma ray or X-ray of a predetermined dose.

Gamma-ray irradiation as an effective method for mitigating antibiotic resistant bacteria and antibiotic resistance genes in aquatic environments

The prevalence of antibiotic resistance genes (ARGs) in municipal wastewater treatment plants (MWTPs) has emerged as a significant environmental concern. Despite advanced treatment processes, high levels of ARGs persist in the secondary effluent from MWTPs, posing ongoing environmental risks. This study explores the potential of gamma-ray irradiation as a novel approach for sterilizing antibiotic-resistant bacteria (ARB) and reducing ARGs in MWTP secondary effluent. Our findings reveal that gamma-ray irradiation at an absorbed dose of 1.6 kGy effectively deactivates all culturable bacteria, with no subsequent revival observed after exposure to 6.4 kGy and a 96-h incubation in darkness at room temperature. The removal efficiencies for a range of ARGs, including tetO, tetA, blaTEM-1, sulI, sulII, and tetW, were up to 90.5% with a 25.6 kGy absorbed dose. No resurgence of ARGs was detected after irradiation. Additionally, this study demonstrates a considerable reduction in the abundances of extracellular ARGs, with the transformation efficiencies of extracellular tetracycline and sulfadiazine resistance genes decreasing by 56.3–81.8% after 25.6 kGy irradiation. These results highlight the effectiveness of gamma-ray irradiation as an advanced and promising method for ARB sterilization and ARG reduction in the secondary effluent of MWTPs, offering a potential pathway to mitigate environmental risks associated with antibiotic resistance.

Growth performance, yield, and proline content of two local cultivars of black rice irradiated by gamma rays for drought resistance

One of the critical effects of climate change on the agricultural environment is drought stress. This study aimed to determine the growth, yield performance, and proline content of black rice local cultivars Bantul, Boyolali mutant M2 at various doses of gamma rays and the proline content of mutant M3 during drought stress. The experiment used a Completely Randomized Design (CRD) with the factor dose of gamma-ray irradiation (0 Gy, 100 Gy, 200 Gy, and 300 Gy), applied in both paddy fields and polybags to observe and compare the growth, yield, and proline content of black rice plants with the control treatment (0 Gy). Laboratory test results showed that Boyolali and Bantul cultivars irradiated at 100 Gy and 200 Gy, had the highest proline content, which increased under drought stress conditions in both cultivars. At 100 Gy, the average plant height and the number of productive tillers of black rice of Boyolali and Bantul cultivars were the highest, and the diversity of the two local cultivars at this dose was higher than at other irradiation doses. Applying 100 Gy and 200 Gy gamma-ray irradiation doses on the Boyolali cultivar significantly affected the panicle length character and the number of seeds per panicle. For the Bantul cultivar, panicle length and the number of seeds per panicle at an irradiation dose of 200 Gy showed significantly different results. The conclusion is that a reduced amount of gamma-ray irradiation can enhance the growth, yield, and proline content of M2 black rice