Gain Suppression Research Articles

Parametric instability in long optical cavities and suppression by dynamic transverse mode frequency modulation

Three mode parametric instability has been predicted in Advanced gravitational wave detectors. Here we present the first observation of this phenomenon in a large scale suspended optical cavity designed to be comparable to those of advanced gravitational wave detectors. Our results show that previous modelling assumptions that transverse optical modes are stable in frequency except for frequency drifts on a thermal deformation time scale is unlikely to be valid for suspended mass optical cavities. We demonstrate that mirror figure errors cause a dependence of transverse mode offset frequency on spot position. Combined with low frequency residual motion of suspended mirrors, this leads to transverse mode frequency modulation which suppresses the effective parametric gain. We show that this gain suppression mechanism can be enhanced by laser spot dithering or fast thermal modulation. Using Advanced LIGO test mass data and thermal modelling we show that gain suppression factors of 10-20 could be achieved for individual modes, sufficient to greatly ameliorate the parametric instability problem.

Burst-mode Yb-doped fiber amplifier system optimized for low-repetition-rate operation

We report on the burst-mode operation of a polarization-maintaining Yb-doped multi-stage all-fiber amplifier capable of generating 10-pulse 100 ns long bursts of 400 μJ total energy. The corresponding average energy per pulse is 40 μJ, with a standard deviation of 16%. The 40 μJ pulses are compressible to a full width at half-maximum of 500 fs. The burst repetition rate is set to 1 kHz and the amplifier is synchronously pulse pumped to minimize amplified spontaneous emission (ASE) between the bursts. A special amplifier design has been developed to suppress ASE further at the cost of lower power efficiency. A detailed investigation of gain and ASE suppression performance of the amplifier in relation to pulsed pumping is presented.

87 W, narrow-linewidth, linearly-polarized 1178 nm photonic bandgap fiber amplifier.

High-power narrow-linewidth photonic bandgap fiber amplifier was demonstrated. In order to suppress stimulated Brillouin scattering, the seed linewidth was broadened by applying a random phase noise with an electro-optical modulator. A factor of 15 in terms of Brillouin gain suppression can be theoretically expected. An 87 W linearly-polarized (11 dB PER) and narrow-linewidth (780 MHz FWHM) output was obtained.

3축 등방성 전계강도 측정 안테나

논문에서는 전자파(EMFs) 측정을 위한 광대역 3축 등방성 안테나를 설계 및 제작하였다. 제안된 3축 안테나의 각축에 따른 개별 안테나는 등방성 특성을 가지며, 임의의 안테나 축을 선택하기 위하여 RF 스위치를 사용하였다. 또한, 안테나의 이득 개선 및 잡음성분을 억제하기 위하여 각 축에 저항을 삽입하였고, 각 다이폴 안테나의 포트 임피던스는 발룬을 사용하여 정합하였다. 안테나의 성능 검증을 위하여, 표준전자기장을 만들어주는 GTEM Cell를 사용하여 antenna factor 및 수신감도를 도출하였다. 결과적으로, 제작된 3축 등방성 안테나는 0.03~3 GHz의 넓은 동작주파수 범위 내에서 수신감도 0.12~4.2 mV/m, VSWR(typical)은 3.3:1 이하이다. In this paper, we designed and fabricated wideband 3-axis isotropic antenna for the Electro-Magnetic Fields(EMFs) measurement. Each part of proposed 3-axis antenna has isotropic characteristics and arbitrary axis of proposed 3-axis antenna could be selectable using RF switch. Also, a resistor was inserted in each axis of proposed 3-axis antenna for improving antenna gain and noise suppression characteristics, and port impedance of each dipole antenna were matched by balun. For the performance verification of antenna, GTEM Cell which generates standard electromagnetic field was used for the derivation of antenna factor and receiver sensitivity. As a result, fabricated 3-axis isotropic antenna has receiver sensitivity of 0.12~4.2 mV/m and typical VSWR of 3.3:1 within a wide operation frequency range from 0.03 MHz to 3 GHz.

Multimode analysis of relative intensity noise associated with intensity modulation of semiconductor lasers

This paper analyzes the relative intensity noise (RIN) associated with intensity modulation (IM) of multilongitudinal mode semiconductor lasers. We considered two states of operation; namely, stable single-mode and multimode hopping that correspond to weak and strong asymmetric gain suppression. The former is typically considered by AlGaAs lasers, whereas the latter is considered by InGaAsP lasers. We introduce comparison of the influence of the modulation parameters on both the total and modal RIN between both lasers. We show that the IM response and 2HD display a peak at the relaxation frequency. The multimode hopping in the InGaAsP laser induces levels of signal distortion much higher than those in the AlGaAs laser in the regime of low modulation frequencies. Under weak modulation, the total and modal RINs of both the lasers vary little from those of the non-modulated lasers. The deep modulation releases the multimode hopping phenomenon in the InGaAsP laser and suppresses the mode-hopping peak in the RIN spectrum.

An Efficient Semi-Analytical Method for Modeling of Traveling-Wave and Reflective SOAs

An efficient semi-analytical method is developed for fast and precise assessment of the steady-state gain characteristics of the semiconductor optical amplifiers. It relies on the analytical solution for the photon densities spatial distribution, starting with the rough estimation without the nonlinear gain suppression, and subsequent refinement of the results by inclusion of the suppression. Carrier density spatial distribution is approximated either by a constant, or a piecewise constant function. Compared with the simplified wideband numerical method, which excludes the photon density spectral dependence, the semi-analytical method requires considerably lower processing resources, and, depending on the model complexity, can be between one and two orders of magnitude faster, without significant sacrifice of the accuracy.

Ytterbium-doped large-mode-area all-solid photonic bandgap fiber lasers.

Single-mode operation in a large-mode-area fiber laser is highly desired for power scaling. We have, for the first time, demonstrated a 50μm-core-diameter Yb-doped all-solid photonic bandgap fiber laser with a mode area over 4 times that of the previous demonstration. 75W output power has been generated with a diffraction-limited beam and an efficiency of 70% relative to the launched pump power. We have also experimentally confirmed that a robust single-mode regime exists near the high frequency edge of the bandgap. These fibers only guide light within the bandgap over a narrow spectral range, which is essential for lasing far from the gain peak and suppression of stimulated Raman scattering. This work demonstrates the strong potential for mode area scaling of in single-mode all-solid photonic bandgap fibers.

Analysis of SBS Gain Shaping and Threshold Increase by Arbitrary Strain Distributions

Fibers with a longitudinal strain distribution can be used to shape the stimulated Brillouin scattering (SBS) gain spectrum or to increase the SBS threshold power. Theoretical analysis and experimental results on the SBS gain spectrum of coiled fibers with a continuous and arbitrary distribution of longitudinal strain are presented. The concept of a critical gain factor for determining the SBS threshold power with a simple formula is reviewed for fibers with different parameters and spectral shapes. A fiber coiling machine for high coiling forces is described for realizing permanent strain distributions with a maximum strain of more than 3%. SBS spectra were broadened to a spectral width of 1.7 GHz. Measurements verify a significant SBS gain suppression by a factor of 40, which is in excellent agreement with the theoretical analysis. Finally, synthetic triangular and broadened Lorentzian SBS spectral shapes with a spectral width of 550 MHz are demonstrated. The results can be used to suppress SBS in high-power fiber lasers and amplifiers or to tailor almost any arbitrary SBS spectral shapes, which could be useful for slow-light or active optical filter applications.

Rate-equation model for multi-mode semiconductor lasers with spatial hole burning

We present a set of rate equations for the modal amplitudes and carrier-inversion moments that describe the deterministic multi-mode dynamics of a semiconductor laser due to spatial hole burning. Mutual interactions among the lasing modes, induced by high- frequency modulations of the carrier distribution, are included by carrier-inversion moments for which rate equations are given as well. We derive the Bogatov effect of asymmetric gain suppression in semiconductor lasers and illustrate the potential of the model for a two and three-mode laser by numerical and analytical methods.

Mode-competition noise associated with microwave modulation of multimode semiconductor lasers

We analyze the mode-competition (MC) phenomenon and the associated noise in multimode semiconductor lasers at microwave modulation. The study is based on the multimode rate-equation model, which takes into account the mechanisms of modal gain suppression. The MC is evaluated by the correlation coefficients between oscillating modes in the laser cavity. We show that an increase in the modulation depth changes the mode coupling from anticorrelation to positive correlation and then to complete coupling, which corresponds to emission of periodic pulses. The frequency spectra of relative intensity noise (RIN) exhibit sharp peaks at the modulation frequency and higher harmonics. The increase in the modulation depth is associated with suppression of the total and modal RIN under high-frequency modulation and with noise enhancement under low-frequency modulation.

The Diversity Gain and ICI Suppression for OFDM Systems Over Doubly Selective Channels

How to compensate the detrimental impact of intercarrier interference (ICI) on BER performance is the key issue of signal detection for orthogonal frequency division multiplexing (OFDM) systems in doubly selective channels. In this paper, we propose an optimal linear ICI suppression algorithm with successive detection based on oversampling at the receiver, by which the OFDM systems can benefit from doubly selective channels for achieving both the multipath diversity and Doppler diversity. To reduce the additional computational complexity caused by oversampling, a low complexity implementation method for this algorithm is also presented. Simulations results show that the proposed algorithm can enhance the BER performance with the increase of the Doppler spread and the oversampled factor.

Theoretical Modeling of Intensity Noise in InGaN Semiconductor Lasers

This paper introduces modeling and simulation of the noise properties of the blue-violet InGaN laser diodes. The noise is described in terms of the spectral properties of the relative intensity noise (RIN). We examine the validity of the present noise modeling by comparing the simulated results with the experimental measurements available in literature. We also compare the obtained noise results with those of AlGaAs lasers. Also, we examine the influence of gain suppression on the quantum RIN. In addition, we examine the changes in the RIN level when describing the gain suppression by the case of inhomogeneous spectral broadening. The results show that RIN of the InGaN laser is nearly 9 dB higher than that of the AlGaAs laser.

DESIGN OF FILTERING MICROSTRIP ANTENNA USING FILTER SYNTHESIS APPROACH

Design, simulation, and measurement of a compact flltering microstrip antenna is presented. A feed line, two hairpin resonators, and a rectangular patch are integrated to form the flltering antenna. The elements together function as a third order bandpass fllter with Chebyshev equal ripple response of 0.043dB at midband frequency of 2.0GHz. The rectangular patch acts not only as a radiating element, but also as the last resonator of the bandpass fllter. The proposed flltering antenna exhibits good out-of- band gain suppression, ∞at in-band gain response, good selectivity at the band edges, and well-shaped radiation pattern.

Spatial and temporal bilateral filter for infrared small target enhancement

This paper presents a spatial and temporal bilateral filter (BF) to detect target trajectories, by extracting spatial target information using a spatial BF and temporal target information using a temporal BF. Background prediction when it is covered by targets is the key to small target detection. In order to apply the BF to a small target detection field for this purpose, this paper presents a novel spatial and temporal BF with an adaptive standard deviation to predict spatial background and temporal background profiles, based on analysis of the blocks surrounding a spatial and temporal filter window. In order to discriminate between the edge or object regions with a flat background and the target region spatially and temporally, spatial and temporal variances of the blocks surrounding the filter window are calculated in a spatial infrared (IR) image and temporal profile. The spatial and temporal variances adjust standard deviations of the spatial and temporal BF. Through this procedure, spatial background and temporal background profiles are predicted, and then small targets can be detected by subtracting the predicted spatial background (and temporal background profile) from the original IR image (and original temporal profile) and multiplying spatial and temporal target information. To compare existing target detection methods and the proposed method, signal-to-clutter ratio gain (SCRG) and background suppression factor (BSF) are employed for spatial performance comparison and receiver operating characteristics (ROC) is used for detection-performance comparison of the target trajectory. Experimental results show that the proposed method has a superior target detection rate and a lower false-alarm rate.

Theoretical Analysis of Unidirectional Operation and Reflection Sensitivity of Semiconductor Ring or Disk Lasers

We theoretically and numerically analyze the unidirectional behavior of ring or disk lasers coupled to a bus waveguide with a relatively strong reflector on one side and find analytical expressions for the ratio of the powers in clockwise and counter clockwise modes. At low bias levels, this ratio depends on the coupling coefficients that determine the coupling between clockwise and counterclockwise modes, whereas at high bias levels it also depends strongly on the gain suppression. We also theoretically and numerically investigate the feedback sensitivity of such lasers and come to the conclusion that ring or disk lasers are generally much more sensitive to external reflections than traditional Fabry-Perot, DFB, or DBR lasers. At high bias levels, the feedback sensitivity also depends strongly on the gain suppression, and at high enough power levels, it can be better than that of traditional edge-emitting lasers.

Mid-infrared Raman amplification and wavelength conversion in dispersion engineered silicon-on-sapphire waveguides

Raman amplification based on stimulated Stokes Raman scattering (SSRS) and wavelength conversion based on coherent anti-Stokes Raman scattering (CARS) are theoretically investigated in silicon-on-sapphire (SOS) waveguides in the mid-infrared (IR) region. When the linear phase mismatch Δk is close to zero, the Stokes gain and conversion efficiency drop down quickly due to the effect of parametric gain suppression when the Stokes-pump input ratio is sufficiently large. The Stokes gain increases with the increase of Δk, whereas efficient wavelength conversion needs appropriate Δk under different pump intensities. The conversion efficiency at exact linear phase matching (Δk = 0) is smaller than that at optimal linear phase mismatch by a factor of about 28 dB when the pump intensity is 2 GW cm−2.

The influence of gain suppression on dynamic characteristics of violet InGaN laser diodes

The influence of gain suppression factor on dynamic characteristics of violet InGaN laser diode (LD) with an emission wavelength near 415nm has numerically been investigated. Different values of gain suppression factor have been used to examine the dynamic characteristics of violet InGaN LD. Simulation results indicate that the gain suppression factor in the non-linear gain equation has potential effects on the carrier and photon dynamics of violet InGaN LD. It is found that the non-linearity of the carrier increases as the injunction current is increased.

Multiple Band-Notched UWB Antenna With Band-Rejected Elements Integrated in the Feed Line

To mitigate potential interferences with coexisting wireless systems operating over 3.3-3.6 GHz, 5.15-5.35 GHz, or 5.725-5.825 GHz bands, four novel band-notched antennas suitable for ultra-wideband (UWB) applications are proposed. These include UWB antennas with a single wide notched band, a single narrow notched band, dual notched bands, and triple notched bands. Each antenna comprises a half-circle shaped patch with an open rectangular slot and a half-circle shaped ground plane. Good band-notched performance is achieved by using high permittivity and low dielectric loss substrate, and inserting quarter-wavelength horizontal/vertical stubs or alternatively embedding quarter-wavelength open-ended slots within the feed line. The results of both simulation and measurement confirm that the gain suppression of the single and multiple band-notched antennas in each desired notched band are over 15 dB and 10 dB , respectively. The radiation pattern of the proposed triple band-notched design is relatively stable across the operating frequency band.

Effects of AgRP Inhibition on Energy Balance and Metabolism in Rodent Models

Activation of brain melanocortin-4 receptors (MC4-R) by α-melanocyte-stimulating hormone (MSH) or inhibition by agouti-related protein (AgRP) regulates food intake and energy expenditure and can modulate neuroendocrine responses to changes in energy balance. To examine the effects of AgRP inhibition on energy balance, a small molecule, non-peptide compound, TTP2515, developed by TransTech Pharma, Inc., was studied in vitro and in rodent models in vivo. TTP2515 prevented AgRP from antagonizing α-MSH-induced increases in cAMP in HEK 293 cells overexpressing the human MC4-R. When administered to rats by oral gavage TTP2515 blocked icv AgRP-induced increases in food intake, weight gain and adiposity and suppression of T4 levels. In both diet-induced obese (DIO) and leptin-deficient mice, TTP2515 decreased food intake, weight gain, adiposity and respiratory quotient. TTP2515 potently suppressed food intake and weight gain in lean mice immediately after initiation of a high fat diet (HFD) but had no effect on these parameters in lean chow-fed mice. However, when tested in AgRP KO mice, TTP2515 also suppressed food intake and weight gain during HFD feeding. In several studies TTP2515 increased T4 but not T3 levels, however this was also observed in AgRP KO mice. TTP2515 also attenuated refeeding and weight gain after fasting, an effect not evident in AgRP KO mice when administered at moderate doses. This study shows that TTP2515 exerts many effects consistent with AgRP inhibition however experiments in AgRP KO mice indicate some off-target effects of this drug. TTP2515 was particularly effective during fasting and in mice with leptin deficiency, conditions in which AgRP is elevated, as well as during acute and chronic HFD feeding. Thus the usefulness of this drug in treating obesity deserves further exploration, to define the AgRP dependent and independent mechanisms by which TTP2515 exerts its effects on energy balance.

Influence of sinusoidal modulation on mode competition and signal distortion in multimode InGaAsP lasers

This paper investigates influence of large-signal modulation on mode oscillation in InGaAsP/InP lasers. The mode competition dynamics under modulation are examined in terms of the temporal trajectories of the total output and the strongest modes as well as their Fourier spectra. The mode coupling induced by the strong spectral gain suppression is evaluated by both the correlation coefficients among the strongest modes and their signal distortion. We show that small and moderate modulations at the multimode hopping of the laser modulate the mode hopping along with modulation of each mode. The mode coupling is characterized by anti-correlation among the modes like as the non-modulated laser. Under modulation with the resonance frequency, the increase in the modulation depth changes mode coupling from anti-correlation to positive correlation and then to complete coupling that correspond to emission of periodic pulses. The mode coupling is characterized by mode competition distortion, which measures the amount of power carried by the mode signal at the frequency of multimode-hopping.