Fourier Transform Infrared Spectra Research Articles

Effect of Chitosan Addition on Porosity of Rice Husk Calcium Silicate Used for Free Fatty Acid Adsorbent from Palm Oil

Studies have been done on developing calcium silicate pores derived from rice husk with and without including chitosan as a template. The chitosan solution was supplemented with sodium silicate derived from rice husk, and then CaCl2 was added. The calcium silicate was calcinated at 900ºC for 4 h. The calcium silicate obtained was characterized using X-ray diffraction (XRD), fourier transform infrared (FT-IR), and Brunauer-Emmett-Teller (BET) analysis. The XRD analysis showed the presence of diffraction peaks corresponding to Wollastonite (CaSiO3) crystals, Wollastonite 2m (CaSiO3), Alite (Ca3SiO5), and larnite (Ca2SiO4). Next, the FT-IR spectrum exhibits Si-O-Si, Si-O-Ca, and Si-OH functional groups, suggesting the presence of calcium silicate material. The BET study of calcium silicate using chitosan templates revealed a pore size of 3.88 nm, a pore volume of 0.1577 cc/g, and a surface area of 81.1519 m2/g. The BET analysis results obtained differed from those of the BET analysis of calcium silicate conducted without using chitosan templates, which were 2.06 nm, 0.069 cc/g, and 13.531 m2/g, respectively. The developed mesoporous calcium silicate was employed as an adsorbent to decrease the concentrations of free fatty acids in palm oil. The acid-base titration method is used to evaluate quantities of free fatty acids. The results obtained from the computation of free fatty acid levels indicate a decline in the concentration of free fatty acids in palm oil. The concentration of free fatty acids derived from palm oil was 1.23%. Therefore, mesoporous calcium silicate-free fatty acids at a concentration of 1.06% resulted in an 86.1% reduction.

Management of caffeine in wastewater using MOF and perovskite materials: optimization, kinetics, and adsorption isotherm modelling

Pharmaceuticals and personal care products (PPCPs) have been increasingly used all over the world and they have been reported on water cycle and cause contamination. Among these pharmaceuticals is caffeine (CAF). In this work, CAF removal from aqueous samples by metal–organic framework (UIO-66) and perovskite (La0.7Sr0.3FeO3) was achieved. Detailed studies on the preparation of MOFs and perovskite oxides compounds have been presented. Extensive characterizations such as X-Ray diffraction (XRD), field emission scanning electron microscope (FESEM), Fourier transform infrared spectra (FT-IR), N2 adsorption–desorption isotherms were also carried out to assure proper formation and to better understand the physico-chemical behavior of the synthesized samples before and after adsorption. Batch experiments of CAF adsorption onto both MOFs and perovskite were performed to compare the effectiveness of both materials on the removal competence of the CAF residue at different conditions including the effect of pH, initial concentration, and contact time. It was observed that the adsorption capacity of CAF by MOF increased with increasing acidity. On the other hand, the adsorption capacity of perovskite is stable in pH 4–10. The maximum adsorption capacities of UiO-66 and perovskite toward CAF are high as 62.5 mg g−1 and 35.25 mg g−1, respectively. Equilibrium isotherms were investigated by numerous models: Langmuir, Freundlich, Temkin, Redlich-Peterson, Sips, Langmuir-Freundlich, Toth, Kahn, Baudu, and Fritz Schlunder. Moreover, the kinetics of the CAF@MOF and CAF@Perovskite systems have been studied by five kinetic models (Pseudo-1st -order (PFO), Pseudo-2nd -order (PSO), Mixed 1st, 2nd-order, Intraparticle diffusion and Avrami). The best model described the adsorption of CAF onto both of MOF and perovskite was the mixed 1st, 2nd-order model. The metal–organic framework and perovskite were applied to quickly extract CAF from water samples successfully. The maximum removal percentage obtained for MOF and perovskite was 0.89% and 0.94% respectively within 30 min contact time which suggests that these materials are considered as promising adsorbents for CAF.

Effect of hydrogen flow rate on properties of silicon oxycarbide thin films via hot wire chemical vapor deposition

AbstractThis study explores the impact of hydrogen flow as a carrier gas on silicon oxycarbide thin films produced via hot wire chemical vapor deposition (HWCVD) using tetraethyl orthosilicate as a precursor. Systematically varying the hydrogen flow rates, the influence on thin film composition, microstructure, and optical properties is investigated. Employing diverse characterization techniques, such as X‐ray diffraction, field‐emission scanning electron microscopy (FE‐SEM), energy‐dispersive X‐ray spectroscopy, Fourier‐transform infrared (FTIR), X‐ray photoelectron spectroscopy (XPS), ellipsometry, and photoluminescence (PL) spectroscopy, it is revealed that there is a correlation between hydrogen flow rate and thin film elemental composition. Higher hydrogen flow rates result in increased silicon content and reduced contributions of oxygen and carbon. FE‐SEM images show agglomerates with improved homogeneity at higher flow rates. FTIR spectra highlight distinctive vibrational modes, including Si–H bonds. XPS confirms the emergence of Si–H bonds at elevated hydrogen flow rates. Ellipsometry indicates increased thickness and refractive index. PL spectra exhibit a broadband across the visible spectrum, influenced by hydrogen‐related defects and electronic transitions. This study provides findings for optimizing HWCVD parameters to tailor thin films for specific applications, emphasizing the important role of hydrogen flow as a carrier gas.

Selective depression and adsorption of a novel eco-friendly depressant on the flotation separation of chalcopyrite from carrollite

Carrollite is often associated with chalcopyrite, and their natural floatability is similar, which makes it difficult to separate the two minerals by flotation in industrial production. In this study, the depression behavior and mechanism of flaxseed gum (FG) introduced as carrollite depressant on carrollite and chalcopyrite in PBX flotation system was investigated through micro-flotation, zeta potential, total organic carbon (TOC), fourier transform infrared (FT-IR), and X-ray photoelectron spectroscopy (XPS). The flotation results indicated that FG was a highly effective depressant to separate 92.39 % chalcopyrite from the mixture with carrollite at pH 9.0 with a reagent scheme of 50 mg/L of FG and 8.0 × 10−5 mol/L of PBX. The zeta potential and TOC analysis results demonstrated that both carrollite and chalcopyrite exhibited a favorable affinity to FG, and pre-treated FG significantly hindered the adsorption of PBX on carrollite, while only slightly decreased that on chalcopyrite, resulting in the considerable difference in floatability between carrollite and chalcopyrite. In addition, FT-IR spectra and XPS detection results further confirmed that the affinity of FG towards carrollite superior to PBX might be due to the bidentate coordination of the carboxyl groups in FG with Co sites on carrollite surface, whereas the interaction between its carboxyl groups and Cu sites on both minerals was very weak or did not happen. Therefore, FG was promising in flotation separation of copper-cobalt sulfide minerals as a new friendly efficient depressant.

Influence of Accelerated Electron-Irradiation on Sorption Properties of Latvian Darkhead Sheep Wool Fibers

Latvian Darkhead (LD) is a local sheep breed and a genetic resource in Latvia. Preservation and development of the sheep population in the local region is important for the recultivation of fields, it serves as a source for export and local use, as well as waste wool can be applied for developing new products, for example, sorbents for volatile organic pollutants. Therefore, investigation of the sorption properties of the LD sheep wool fibers is under interest. In addition, modification options of the wool for improvement of properties are viewed. Therefore, in the present work, sheep wool fibers as well as accelerated electron-irradiated fibers are analyzed and compared. Fourier transform infrared (FTIR) spectrometry is applied to develop the sorption testing system of volatile organic compounds. An analytical system consisting of a volatile organic compound source, sheep wool filter, and FTIR spectrometry cell is tested and applied for analysis of wool sorption properties for acetone molecules. Registration of the FTIR spectra was performed within the range of 600-4000 cm-1, in the nitrogen flow of about 150mL/min. FTIR analysis shows, that the accelerated electron irradiated sheep wool fibers absorb acetone of about 33% more than non-irradiated fibers. The obtained results will be used for developing recommendations for filter producers to fabricate filter components containing LD sheep wool fibers.

Enhanced photocatalytic removal of azo dye by the K3NaCo4(MoO4)6/H2O2 system

K3NaCo4(MoO4)6 photocatalyst has been prepared using a solid-state reaction method. First, its crystal structure is determined from single-crystal X-ray diffraction data. This material crystallizes in trigonal system, space group R3¯ (No.148) with cell parameters a = 14.434(3) Å and c = 19.811(6) Å. The crystal structure of the title compound can be described by the junction of ribbons and MoO4 tetrahedra by sharing vertices to give a three-dimensional framework in which Na+ and K+ cations are resided. Second, the as prepared sample has been characterized by X-ray diffraction (XRD), Fourier transform infrared (FTIR), Raman spectroscopy, UV–visible spectroscopy, scanning electron microscope (SEM) and EDX analysis. The SEM analysis demonstrates the presence of agglomerates with uniform nanoparticles having different crystallite sizes. FTIR and Raman spectra confirm the presence of characteristic MoO4 tetrahedra. Moreover, the optical band gap was found to be 3.5 eV. Finally, the photocatalytic removal of Acid Yellow 23 (AY-23) organic azo dye was investigated under solar light in the presence of K3NaCo4(MoO4)6 photocatalyst and H2O2. A good photocatalytic activity for the degradation of AY-23 dye has been noted with a removal rate reaching 98 % when adding H2O2 at optimum reaction. The elimination of AY-23 increased with the addition of 5 mM H2O2 concentration. The rate constant of the photocatalytic process in the K3NaCo4(MoO4)6/H2O2 system is about 1.2 × 10-1h−1.

From laboratory to industrial use: Understanding process variation during enzymatic protein hydrolysis with dry film fourier-transform infrared spectroscopy

Industries are continuously looking for dedicated sensor solutions for evaluating the chemical composition of products that can provide valuable insights into process control, process optimization, and product quality. A rapid and robust analytical method, Fourier-Transform Infrared (FTIR) spectroscopy, holds significant potential in this regard as it provides detailed compositional values of food nutrients. The main aim of the present study was to use dry film FTIR spectroscopy as an analytical tool to characterize products from an industrial enzymatic protein hydrolysis process and link this to understand industrial process variations. For this purpose, 463 protein hydrolysate samples were obtained from an industrial enzymatic protein hydrolysis plant. In the same period, systematic variations in process parameters such as raw material composition, enzyme type, and water addition, were performed. All samples were analyzed using dry film FTIR spectroscopy. Two subsets containing 200 and 68 hydrolysate samples were chosen for measuring average molecular weight (AMW) and collagen content respectively, providing reference data for constructing calibration models based on partial least squares regression (PLSR). The percentage of low molecular weight constituents was derived from the molecular weight distribution of size exclusion chromatograms of protein hydrolysates and also used in the modeling. Calibration models for the prediction of AMW, low molecular weight constituents, and collagen content were obtained with a good fit and lower estimation errors. Principal component analysis (PCA) of protein hydrolysates' FTIR spectra effectively differentiated process variations (enzyme types and raw materials) without extensive reference analysis. One-factor analysis of variance (ANOVA) tests was used to observe the impact of process variation on product quality. FTIR proved to be a sensitive method for liquid protein analysis and process control with a significant potential in process optimization approaches. To the authors’ knowledge, this is the first time dry film FTIR spectroscopy has been used to evaluate an industrial bioprocess with designed process variations.

Aqueous removal of Cr(VI) by Citrus sinensis juice-coated multi-walled carbon nanotubes

A novel adsorbent was prepared from multi-wall carbon nanotubes (MWCNTs) and Citrus sinensis juice extract-modified MWCNTs (OJMW) and characterized using scanning electron microscopy (SEM), Fourier transform infrared spectra (FTIR), X-ray diffractometer (XRD), BET and thermogravimetric analysis. The results showed that the nanotubes exhibited good surface area, pore size, functional groups, and robust stability at elevated temperatures (308 and 313 K). The adsorbent was applied in water for the sequestration of Cr(VI). The adsorption of Cr(VI) on MWCNTs and OJMW was influenced by factors of adsorption. Optimum removal of Cr(VI) was attained at 180 min contact time, 0.05 g adsorbent dose, and solution pH 2 for MWCNTs and OJMW. The kinetic behaviour of the Cr(VI) adsorption onto MWCNTs and OJMW was governed by the pseudo-first-order and pseudo-second-order kinetic model, respectively. The equilibrium data obtained for the uptake of Cr(VI) onto MWCNTs and OJMW fitted satisfactorily with Freundlich and Langmuir isotherm models, respectively. Meanwhile, MWCNTs and OJMW exhibited monolayer adsorption capacities (qmax) of 44.72 and 12.26 g g−1, respectively, at 298 K. The adsorption process was spontaneous and feasible. The direction of energy flow in the uptake of Cr(VI) onto OJMW and MWCNTs followed endothermic and exothermic adsorption processes, respectively. The adsorption–desorption experiments showed that OJMW had good regenerative abilities.

Catalytic Reduction of 4-Nitrophenol and Methylene Blue with Silver Nanoparticles Decorated with Drymoglossum piloselloides Extract

Drymoglossum piloselloides is one of the epiphytic plants that is commonly found in Southeast Asia region. In this study, the ethanol extract of D. piloselloides plant has been used in the green synthesis of silver nanoparticles. The synthesized silver nanoparticles were characterized by ultraviolet-visible (UV-Vis) spectrophotometry, X-ray diffraction (XRD),Fourier-transform infrared (FTIR) spectroscopy, and transmission electron microscopy (TEM) measurements. The UV-Vis spectrum of silver nanoparticles showed a maximum wavelength at 453 nm. The XRD measurement showed the silver nanoparticles peaks at 38.38°, 44.60°, 64.76°, and 77.62°. The FTIR spectra provided evidence of the interaction between silver and chemicals in the plant extract as a weak signal at 682 cm-1. Meanwhile, TEM revealed an average size of 12.63nm. The synthesised silver nanoparticles were utilised for the reduction of 4-nitrophenol with a conversion percentage of up to 100% with a reduction reaction rate constant of 7.104 s-1. In addition, methylene blue was also successfully reduced with the synthesised silver nanoparticles as the catalyst with a reduction reaction rate constant (k) of 21.150 s-1. This study highlights the superior advantage of utilizing ethanolic extract of D. piloselloides to prepare silver nanoparticles with promising catalytic reduction purposes.

Probing the stability and quality of the cellulose-based Pickering emulsion containing sesamolin-enriched sesame oil by chemometrics-assisted ATR-FTIR spectroscopy

This study presents the employment of Fourier transform infrared (FTIR) spectroscopy with attenuated total reflection and principal component analysis (PCA) to analyze the stability of a Pickering emulsion stabilized by carboxylated-cellulose nanocrystal (cCNC) comprising sesame oil phases with or without sesamolin. FTIR measurements identified an intermolecular hydrogen bond between the ester group of the triglyceride and the carboxyl group of the cCNC to create the emulsion droplet. The spectral bands from the hydroxyl group vibration (3700–3050 cm−1), carbonyl (1744 cm−1), CO groups of the ester triglyceride and cCNC (1160–998 cm−1) markedly discriminated between stabilized and destabilized emulsions. The PCA of FTIR spectra detected the change of molecular interaction during storage according to creaming, aggregation, and coalescence and changes in physicochemical parameters such as droplet size, refractive index, and zeta potential. Hence, PCA enabled the observation of the destabilization of emulsion in real-time.

Consecutive high-performance removal of Cu2+ metal ions and Deltamethrin using multifunctional pyrolysis cuttlebone/cotton fabric nanocomposite

A simple technique was developed for the modification of cotton materials that is inexpensive, environmentally friendly, and very effective. Waste Cotton fabrics (WCFs) are loaded with propolis extract (PE) for Cu2+ removal. Then, Cu2+ underwent a pyrolysis process with modified cuttlebone (CB) at 900 °C for 5 h. The surface of the prepared materials was characterized using X-ray diffraction (XRD), scanning electron microscopy with energy-dispersive X-ray (SEM-EDX), Fourier transform infrared (FTIR), BET, particle sizes, thermogravimetric analysis (TGA) and zeta potential analysis. The Cu2+ metal ions from an aqueous solution were removed using WCFs/PE, and DLM was subsequently removed using pyro WCFs/PE/Cu/CB. The as-prepared NPs exhibited the face-centered cubic structure of WCFs/PE/Cu/CB with crystallite sizes ranging from 386.70 to 653.10 nm. FTIR spectra revealed that CB was present on the surface of the resulting WCFs/PE/Cu. SEM revealed the dispersion of a uniformly flower-like morphology over a large area. Sorption studies were performed based on parameters that included pH, dose, contact time, and initial concentration. The adsorption isotherm and the kinetic studies of the DLM adsorption process were applied at a pH of 5.0 and a temperature of 25 °C using several isotherms and kinetic models. The results revealed qmax (20.51 mg/g) with R2 = 0.97, the Langmuir isotherm that best matches the experimental data. Hence, the Langmuir isotherm suggests that it is the model that best describes sorption on homogenous surfaces or surface-supporting sites with various affinities. The correlation coefficient R2, χ2, adjusted correlation coefficient, and error functions like root mean square (RMSE), normalized root mean square error (NRMES), and mean absolute error (MAE) were used to evaluate the best-fit models to the experimental adsorption data. Moreover, cost estimation for the prepared adsorbent WCFs/PE/Cu showed that it costs approximately 3 USD/g, which is a cheap adsorbent compared to other similar adsorbents reported in the literature. The examined WCFs/PE have significant applicability potential for Cu2+-laden wastewater treatment due to their superior Cu2+ metal ions adsorption capability and reusability.The cytotoxicity and safety study showed that at higher concentrations, it resulted in much less cell viability. Additionally, the removal efficiency of Cu2+ metal ions from synthetic, realistic industrial wastewater using WCFs/PE reached up to 96.29 %, demonstrating good adsorption capability. Thus, there is a huge possibility of accomplishing this and performing well. This study paves the way for the reuse and valorization of selected adsorbents following circular economy principles.Two green metrics were applied, the Analytical Eco-scale and the Analytical GREEnness Calculator (AGREE).

ADSORPTION OF CATION DYE USING ACTIVATED CARBON DERIVED FROM GOLDEN SHOWERSEED POD ( C ASSIA FISTULA)

This study investigated the use of Golden shower seed pod (cassia fistula) as an adsorbent for the removal of cationic dye in a batch system. The raw material was Carbonized at 600 oC for one hour to obtain a purely carbonized material; then impregnated with NaOH of 0.1M and allowed to stay for 24 hours to obtain the desired GS-AC activated carbon. The adsorbent was characterized using scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and energy-dispersive X-ray fluorescence (EDXRF) elemental composition analysis. The effects of adsorbent dosage and contact time on the adsorption process were studied in a batch system. The results revealed that, there was good enhancements in pores of the adsorbent GS-AC due to the chemical impregnation. The FTIR spectra showed the presence C-H, NH 2, C-O, and S=O functional groups indicating a favourable surface for adsorption. Batch studies indicated that, the methylene blue uptake decreased with increase in the GS-AC dosage. The amount of Methylene blue adsorbed onto GS-AC increased with time and subsequently remained constant at some point in time with maximum uptake at 500 mg/l. Thus, adsorption capacity of methylene blue increased with longer contact time, indicating a stronger interaction between the adsorbent and the dye. Based on the findings, Golden shower seed pod (cassia fistula) impregnated with NaOH can be used as an alternative and suitable material for cationic dye removal from liquid phase.

Integrated Janus nanofibers enabled by a co-shell solvent for enhancing icariin delivery efficiency

During the past several decades, nanostructures have played their increasing influences on the developments of novel nano drug delivery systems, among which, double-chamber Janus nanostructure is a popular one. In this study, a new tri-channel spinneret was developed, in which two parallel metal capillaries were nested into another metal capillary in a core–shell manner. A tri-fluid electrospinning was conducted with a solvent mixture as the shell working fluid for ensuring the formation of an integrated Janus nanostructure. The scanning electronic microscopic results demonstrated that the resultant nanofibers had a linear morphology and two distinct compartments within them, as indicated by the image of a cross-section. Fourier Transformation Infra-Red spectra and X-Ray Diffraction patterns verified that the loaded poorly water-soluble drug, i.e. icariin, presented in the Janus medicated nanofibers in an amorphous state, which should be attributed to the favorable secondary interactions between icariin and the two soluble polymeric matrices, i.e. hydroxypropyl methyl cellulose (HPMC) and polyvinylpyrrolidone (PVP). The in vitro dissolution tests revealed that icariin, when encapsulated within the Janus nanofibers, exhibited complete release within a duration of 5 min, which was over 11 times faster compared to the raw drug particles. Furthermore, the ex vivo permeation tests demonstrated that the permeation rate of icariin was 16.2 times higher than that of the drug powders. This improvement was attributed to both the rapid dissolution of the drug and the pre-release of the trans-membrane enhancer sodium lauryl sulfate from the PVP side of the nanofibers. Mechanisms for microformation, drug release, and permeation were proposed. Based on the methodologies outlined in this study, numerous novel Janus nanostructure-based nano drug delivery systems can be developed for poorly water-soluble drugs in the future.

Greater difference between airborne and flower pollen chemistry, than between pollen collected across a pollution gradient in the Netherlands

The prevalence in allergic diseases has increased considerably in the past decades. An important trigger of the symptoms of allergic rhinitis (hay fever) is the pollen of wind-pollinating plants. This pollen is developed by plants and is released into the air where it gets exposed to environmental influences and air pollution. We investigated the chemical changes to pollen that occur after release from the flower in a rural (Veluwe) and an urban (Amsterdam) site in the Netherlands using Fourier Transform Infrared (FTIR) spectroscopy. During the spring/summer of 2020 (during the COVID pandemic) the pollen of nine taxa (Alnus, Betula, Fagus, Fraxinus, Pinus, Plantago, Poaceae, Quercus and Salix) were collected directly from flowers and the air (using a mobile sampler). FTIR spectra were obtained for multiple individual pollen grains for each taxa. The spectra obtained from airborne pollen collected at the rural vs. urban sites did not show any statistical difference. This is possibly a result of a reduced difference in pollutant concentrations between the two sites due to the COVID-19-lockdown measures were in place. However, consistent differences in the FTIR spectra recovered from airborne vs. flower pollen were recorded for all pollen taxa. After the release from the flower the chemical composition of the pollen changed: (i) polysaccharides are converted to monosaccharides; (ii) protein concentration and/or nitration/oxidation level is altered; (iii) lipids are modified and/or reduced in concentration. These changes may alter the allergenicity of the pollen and suggest that further work on the allergenic nature of airborne pollen is required.

FTIR determination of the degree of molar substitution for hydroxypropyl chitosan

We developed and validated a novel Fourier transform infrared (FTIR) method to determine the degree of molar substitution (MS) for hydroxypropyl chitosan (HPCS) using nuclear magnetic resonance (1H NMR) as a reference, and investigated the factors influencing the MS assay. Through extensive screening of integration methods for candidate bands in the FTIR spectrum of HPCS using 20 HPCS samples with degrees of acetylation (DA) ranging from 0.003 to 0.139, we found that when using band area at 2970 cm−1 as a probe integral, the MS values obtained via the 1H NMR method exhibited linear correlations (R2 > 0.98) with at least 16 integral ratios derived from their FTIR spectra. The optimal reference bands with high reliability are located at 3440 cm−1 and 1415 cm−1, with R2 exceeding 0.99 and a MS range of 0.17–1.92. The band at 2875 cm−1 is less affected by the trace moisture present in HPCS samples than the others. The results of the method validation demonstrated a mean recovery of 98.9 ± 2.8 % and an RSD below 10 %, suggesting a simple, robust, and highly accurate and precise method. This method could be extendable for the determination of the MS of insoluble HPCS derivatives and other hydroxypropylated polysaccharides.

Preparation, characterization and photocatalytic studies of defect pyrochlore, KMn0·33Te1·67O6 and its composite with g-C3N4

Skeletal materials belonging to the defect pyrochlore family have been the subject of considerable interest due to their remarkable properties. In this work, a highly efficient, stable and visible light active composite photocatalytic system consisting of defect pyrochlore of composition KMn0·33Te1·67O6 (KMnTeO) and g-C3N4 (g-CN) has been successfully prepared by simple physical mixing of pre-prepared KMnTeO and g-CN components synthesized in solid state and thermal treatment of low-cost melamine, respectively. Structural, morphological and optical properties of as-prepared catalysts were deduced from powder X-ray Diffraction (XRD), Fourier Transform Infrared (FT-IR), Raman, Field Emission Scanning Electron Microscopy-Energy Dispersive X-ray Spectroscopy (FESEM-EDX), Transmission Electron Microscopy-High Resolution Transmission Electron Microscopy (TEM-HRTEM), Ultraviolet–Visible Diffuse Reflectance Spectroscopy (UV–Vis DRS), X-ray Photoelectron Spectroscopy (XPS) and Photoluminescence (PL) measurements. The lattice parameter “a” of parent KMnTeO was obtained from Rietveld refinement of its powder XRD pattern. The FT-IR and Raman spectra of KMnTeO gave characteristic bands belonging to the defect pyrochlore structure. The photocatalytic activities of KMnTeO and composite KMnTeO-g-CN were evaluated by the degradation of methylene blue (MB). Scavenger experiments were carried out to identify the reactive species responsible for the degradation of MB. Furthermore, the reusability and stability of the photocatalysts were explored. The probable photocatalytic mechanism for MB degradation over the composite KMnTeO-g-CN was surmised according to the scavenger experiments. The work provides a new approach for the development of novel defect pyrochlore based composite photocatalysts to treat industrial wastewater containing organic pollutants.

Carbon gas sensors synthesized using acacia auriculiformis tree branches to detect methanol, ethanol, acetone vapors and ammonia gas

Metal oxides and carbon are the prime candidates of gas sensor devices. For the inaugural instance, carbonaceous particulate matter was meticulously derived from the branches of Acacia auriculiformis tree indigenous to Sri Lanka to detect vapor and gas. It is worth noting that biomass derived carbon had hitherto remain unexplored in the realm of vapor and gas detection. Carbon films were fabricated via the doctor blade method. The resistivity characteristic of these carbon samples exhibited discernible variations upon exposure to methanol, ethanol, acetone vapors, and ammonia gas. Notably, the gas-sensing properties of sample derived from the central core and the outer shell of Acacia auriculiformis tree branches were independently assessed in these vapors and gas at ambient temperature. Various analytical techniques, including X-ray diffraction (XRD), UVvisible absorption spectroscopy, Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM), were judiciously employed to scrutinize the structural attribute, optical band gap, chemical composition and surface morphology of the aforementioned carbon film samples, respectively. XRD analyses unequivocally confirmed the successful formation of carbonaceous films. FTIR spectra conspicuously delineated the presence of oxygen within the carbon films. Importantly, the optical band gap of our carbon films manifested within the range characteristic of organic carbon. Furthermore, the resistance of the carbon films demonstrated a significant reduction upon adsorption of each vapor. It is noteworthy that while gas sensitivities and response times were superior for carbon derived from the central core of the Acacia tree branches, the recovery times were notably expedited for carbon synthesized from the outer shell of these branches. The zenith of gas sensitivity, an impressive 187%, was recorded in response to 1000 ppm of methanol vapor, when employing carbon sourced from the central core of the acacia tree branches.

Fabrication of Magnetic Molecularly Imprinted Polymers for Selective Extraction of Dibutyl Phthalates in Food Matrices.

In this study, a novel magnetic molecularly imprinted polymeric material (Fe3O4@MOF@MIP-160) with a metal-organic backbone (Fe3O4@MOF) carrier was prepared using dibutyl phthalate (DBP) as a template. The material can be used for the efficient, rapid, and selective extraction of trace amounts of phthalic acid esters (PAEs) in food and can detect them via gas chromatography-mass spectrometry (GC-MS). The synthesis conditions of the materials were optimized to prepare the Fe3O4@MOF@MIP160 with the highest adsorption performance. Transmission electron microscopy (TEM), Fourier Transform Infrared Spectra (FT-IR), Vibration Sample Magnetic (VSM), and the Brunauer-Emmett-Teller (BET) method were used to characterize the materials. Compared with Fe3O4@MOF and the magnetic non-imprinted polymeric material (Fe3O4@MOF@NIP), Fe3O4@MOF@MIP-160 possesses the advantages of easy and rapid manipulation of magnetic materials, the advantages of high specific surface area and the stability of metal-organic frameworks, and the advantages of high selectivity of molecularly imprinted polymers. Fe3O4@MOF@MIP-160 has good recognition and adsorption capacity for di-butyl phthalate (DBP) and diethylhexyl phthalate (DEHP): the adsorption capacity for DBP and DEHP is 260 mg·g-1 and 240.2 mg·g-1, and the adsorption rate is fast (reaching equilibrium in about 20 min). Additionally, Fe3O4@MOF@MIP160 could be recycled six times, making it cost-effective, easy to operate, and time-saving as compared to traditional solid-phase extraction materials. The phthalate ester content in drinking water, fruit juice, and white wine was analyzed, with recoveries ranging from 70.3% to 100.7%. This proved that Fe3O4@MOF@MIP160 was suitable for detecting and removing PAEs from food matrices.

Ammonium ion removal from aqueous solutions in the presence of organic compounds, using biochar from banana leaves. Competitive isotherm models

BackgroundIndustrial, e.g. food industrial and domestic wastewaters contain huge amount of compounds causing eutrophication, and should be removed with high cost during wastewater treatment. However, these compounds could be utilized as fertilizers too. Biochar can remove a wide range of pollutants from water, such as ammonium, which can be found in relatively high concentration in dairy wastewaters. However, adsorption performance may be affected by the presence of other wastewater pollutants. Thus, this study aims to determine the efficiency of biochar as an adsorbent of ammonium in aqueous solutions in the presence of some selected organic compounds of typical dairy wastewaters such as bovine serum albumin (BSA), lactose, and acetic acid. Methods: The biochar was produced from banana leaves at 300 °C, modified with NaOH, and characterized by Scanning Electron Microscope – Energy Dispersive X-Ray Spectroscopy (SEM-EDX), Fourier-transform infrared spectra (FTIR) analysis, and specific surface area measurements. Batch experiments were carried out to investigate the ammonium adsorption capacity and the ion competitive adsorption mechanism. Significant Findings: Results show that the surface structure of the biochar derived from banana leaves is different from other biochars previously studied; although the specific surface area is not very considerable and despite having nitrogen within the elemental composition, the biochar studied is capable of adsorbing 2.60 mg NH4+/m2, the highest ammonium removal in 2 h occurs at pH 9 and 500 mg biochar dose. Langmuir model in the monolayer phase analysis fits better for all scenarios and the maximum NH4+ adsorption capacity was 0.97 mg/g without organic compounds. In the multilayer adsorption phase, the isotherm model that best fits the data obtained is the Harkins-Jura model without organic compounds. The presence of organic compounds in the aqueous solution significantly impacts the adsorption of ammonium by biochar since it improves the adsorption capacity (1.132 mg/g BSA, 0.975 mg/g lactose, and 1.874 mg/g acetic acid). The Aranovich-Donohue isotherm model fitted the data obtained during ion competitive adsorption experiments well.

Polyvinyl pyrrolidone/ carboxymethyl cellulose (PVP/CMC) polymer composites containing CuO nanoparticles synthesized via laser ablation in liquids

Polyvinyl pyrrolidone/carboxymethyl cellulose (PVP/CMC) polymer composites containing CuO nanoparticles synthesized via laser ablation in liquids were prepared. Fourier transform infrared (FTIR) spectroscopy, UV/Vis spectroscopy, and scanning electron microscopy (SEM) were used to characterize the structural, optical, and morphological properties of the polymer composites. The addition of CuO nanoparticles resulted in changes in the FTIR spectra, indicating interaction between the polymer matrix and nanoparticles. UV/Vis spectroscopy showed a red shift in absorption and a decrease in optical bandgap with increasing CuO nanoparticle content. SEM micrographs revealed increases in surface roughness with higher CuO nanoparticle loading. Antibacterial activity of the composites against Gram-positive and Gram-negative bacteria increased with greater CuO nanoparticle concentration. The results suggest these biofilms have potential for use as coating materials in biomedical applications.