Pore Formation Research Articles

Synergizing empirical and AI methods to examine nano-silica's microscale contribution to epoxy coating corrosion resistance

Epoxy-nanomaterials offer a promising solution to combat corrosion threatening civil infrastructure. To examine the impact of nano silica on corrosion resistance, varying amounts of nano silica, ranging from 0.0 to 3 wt%, were introduced into the epoxy matrix. Mechanical properties were studied through studying the dog-bone tensile strength and tribological aspects were assessed through mass loss abrasion tests. Corrosion resistance performance was studied using electrochemical impedance spectroscopy (EIS) and salt spray tests. Nano structure of the coated specimens was studied after salt spray tests using SEM-EDX analysis. Micro Chromatography (M-Ct) technique was employed to investigate the pore formation in the epoxy matrix. Besides, atomic force microscopy (AFM) was introduced to study surface roughness. The test results displayed a notable improvement (5–10 %) in tensile strength upon the introduction of nano silica. Taber tester results showed a reduction in mass loss with the addition of nano silica. Electrochemical impedance spectroscopy (EIS) studies further established a significant increase in corrosion resistance, having an impedance of 12 GOhm.cm2 for epoxy matrix samples containing 2.5 % nano silica after a 768-h salt spray test. SEM-EDX analysis revealed the absence of iron content in the epoxy matrix reinforced with uniformly distributed nano silica. Surface roughness assessments illustrated that nanolaminates contributed to an increase in overall roughness, minimizing surface irregularities in the epoxy matrix. Micro-CT scanning results proposed a decrease in epoxy matrix porosity upon the addition of nano silica. AI based prediction model helped to understand the relationship between surface roughness and corrosion. In summary, the experimental findings suggest valuable insights for future advancements in the development of protective coatings for worldwide civil infrastructures.

ANT-Mediated Inhibition of the Permeability Transition Pore Alleviates Palmitate-Induced Mitochondrial Dysfunction and Lipotoxicity.

Hyperlipidemia is a major risk factor for vascular lesions in diabetes mellitus and other metabolic disorders, although its basis remains poorly understood. One of the key pathogenetic events in this condition is mitochondrial dysfunction associated with the opening of the mitochondrial permeability transition (MPT) pore, a drop in the membrane potential, and ROS overproduction. Here, we investigated the effects of bongkrekic acid and carboxyatractyloside, a potent blocker and activator of the MPT pore opening, respectively, acting through direct interaction with the adenine nucleotide translocator, on the progression of mitochondrial dysfunction in mouse primary lung endothelial cells exposed to elevated levels of palmitic acid. Palmitate treatment (0.75 mM palmitate/BSA for 6 days) resulted in an 80% decrease in the viability index of endothelial cells, which was accompanied by mitochondrial depolarization, ROS hyperproduction, and increased colocalization of mitochondria with lysosomes. Bongkrekic acid (25 µM) attenuated palmitate-induced lipotoxicity and all the signs of mitochondrial damage, including increased spontaneous formation of the MPT pore. In contrast, carboxyatractyloside (10 μM) stimulated cell death and failed to prevent the progression of mitochondrial dysfunction under hyperlipidemic stress conditions. Silencing of gene expression of the predominate isoform ANT2, similar to the action of carboxyatractyloside, led to increased ROS generation and cell death under conditions of palmitate-induced lipotoxicity in a stably transfected HEK293T cell line. Altogether, these results suggest that targeted manipulation of the permeability transition pore through inhibition of ANT may represent an alternative approach to alleviate mitochondrial dysfunction and cell death in cell culture models of fatty acid overload.

A modified pore evolution particle model applied to CaCO3 decomposition and CaO sintering during calcium looping CO2 cycles

The calcium looping of calcium-based carbonation/calcination cyclic reaction is an efficient decarbonization technology that can be applied to post-combustion carbon capture, solar thermal storage, and enhanced methane reforming hydrogen. The pore structure generated during the calcination stage greatly affects adsorption performance. Hence, the change of pore structure is crucial during the calcination. Existing models related to pore structure still need to be further improved regarding pore formation mechanisms. In this paper, a modified pore evolution model is proposed. The modified pore evolution model contains the kinetic equation, the CO2 diffusion equation, and the vacancy aggregates equation. The modified model considers the possibility of spontaneous pore formation in the mechanism, which can better fit the experimental results and provide higher simulation accuracy. The model reveals the diffusion of CO2 within the particles during decomposition, and spatiotemporal evolutionary properties of pore parameters. The pore change trend is the most obvious when the initial pores are mainly 3 nm mesopores. The pore evolution is relatively stable when the initial pores are mainly 25 nm mesopores. Besides, the particles experience significant pore migration during the sintering stage when the temperature reaches 1273 K. At 1073 K, the maximum pore size occurring during pore evolution did not exceed 40 nm. The model estimates a maximum pore size of more than 60 nm at 1273 K. The modified model can aid in a deeper comprehension of how the pore structure changes throughout the calcination process.

Chestnut soil organic carbon is regulated through pore morphology and micropores during the seasonal freeze–thaw process

Soil aggregates are basic structural units in soil organic carbon (SOC) protection. In alpine ecosystems, the seasonal freeze–thaw (FT) process characterizes soil formation and nutrient cycling. However, previous studies were mostly based on simulated FT experiments, which amplified the effects of natural FT processes. And, the regulations of pore structure on SOC protection/loss of aggregates during the FT processes were still not well understood. To investigate the effect of the seasonal FT process on SOC and pore structure of aggregates, as well as the interactions among them, soil samples were selected during a whole seasonal FT cycle, which can be divided into four periods: unstable freezing (UFP), stable frozen (SFP), unstable thawing (UTP), and stable thawed periods (STP). The results demonstrated that freezing increased SOC concentration as the total organic carbon (TOC) content of all aggregate fractions peaked in the SFP (17.46 g/kg on average). The TOC content of aggregates in the UFP dropped to 7.91 g/kg on average, which revealed a dramatic SOC loss after thawing began. Thawing also decreased the proportions of particulate organic carbon (POC) compared with mineral-associated organic carbon (MAOC). The highest microbial abundance was also found in the SFP. Freezing promoted the formation of pores > 80 μm while thawing increased the regularity of pore morphology. Pore structure explained 48.77 % of the SOC variance in the thawing period, but only 19.29 % of that in the freezing period. Overall, in the freezing process, soil pore structure impacted the SOC input by mediating pore morphology. In the thawing process, soil pore structure inhibited SOC loss by enhancing the formation of pores < 15 μm. These results demonstrate new perspectives on the soil aggregate microstructure–microbe–SOC interactions.

A mechanism study of thermal resistance formation and post-fire strength recovery in cement paste with carbon nanotubes and nanosilica via focused ion beam/scanning electron microscopy tomography

Although carbon nanotubes (CNT) and nanosilica (NS) have shown substantial potential for enhancing the thermal resistance and post-fire mechanical recovery of cementitious composites, their combined synergistic effects remain unclear. This study aimed to elucidate the influence of CNT and NS double-hybrids on the physicochemical properties of cementitious composites under different heating temperatures (200, 500, and 800 °C) and re-curing conditions (25 °C/65 % RH and water immersion). We assessed the changes in the compressive and tensile strengths, bulk density, surface morphology, hydration products, and pore characteristics using focused ion beam scanning electron microscopy to visualize the evolving nanoscale pore structures. Our findings reveal a remarkable synergistic effect on the thermal resistance and strength recovery properties of the CNT/NS hybrid samples, owing to the stable matrix observed after heating to 800 °C. Following exposure to 800 °C, the tensile strength exhibited a remarkable 69.6 % increase compared to its pre-heating state, without any indication of crack formation. The CNT served as nucleation sites, expediting the pozzolanic reaction of NS during heating and resulting in a homogenized pore structure with interconnected hydrates. The CNT/NS hybrid samples exhibited uniform shrinkage of hydrates without creating nanoscale rod-like pores typical in ordinary cement paste, while the increase in pore volume was predominantly attributed to the expansion of existing pores and the formation of nearby new pores.

Free Energy Analysis of Peptide-Induced Pore Formation in Lipid Membranes by Bridging Atomistic and Coarse-Grained Simulations.

Antimicrobial peptides (AMPs) are attractive materials for combating the antimicrobial resistance crisis because they can kill target microbes by directly disrupting cell membranes. Although thousands of AMPs have been discovered, their molecular mechanisms of action are still poorly understood. One broad mechanism for membrane disruption is the formation of membrane-spanning hydrophilic pores which can be stabilized by AMPs. In this study, we use molecular dynamics simulations to investigate the thermodynamics of pore formation in model single-component lipid membranes in the presence of one of three AMPs: aurein 1.2, melittin and magainin 2. To overcome the general challenge of modeling long time scale membrane-related behaviors, including AMP binding, clustering, and pore formation, we develop a generalizable methodology for sampling AMP-induced pore formation. This approach involves the long equilibration of peptides around a pore created with a nucleation collective variable by performing coarse-grained simulations, then backmapping equilibrated AMP-membrane configurations to all-atom resolution. We then perform all-atom simulations to resolve free energy profiles for pore formation while accurately modeling the interplay of lipid-peptide-solvent interactions that dictate pore formation free energies. Using this approach, we quantify free energy barriers for pore formation without direct biases on peptides or whole lipids, allowing us to investigate mechanisms of pore formation for these 3 AMPs that are a consequence of unbiased peptide diffusion and clustering. Further analysis of simulation trajectories then relates variations in pore lining by AMPs, AMP-induced lipid disruptions, and salt bridges between AMPs to the observed pore formation free energies and corresponding mechanisms. This methodology and mechanistic analysis have the potential to generalize beyond the AMPs in this study to improve our understanding of pore formation by AMPs and related antimicrobial materials.

Multi-angle analysis of Mo on martensite–austenite component and toughness in SCGHAZ of X80 pipeline automatic ring welding

In order to solve the embrittlement problem of welded joint of pipeline steel, this paper proposes to study the influence of Mo on M-A component of the subcritically reheated coarse-grained HAZ (SCGHAZ), and Mo on bainite transformation. Through the welding thermal simulation experiment, two kinds of X80 pipeline steel with different Mo content were set different secondary thermal cycle peak temperatures to simulate the heat affected zone (HAZ). Samples in the SCGHAZ were selected to observe the microstructure, M-A component, microalloy-element distribution and fracture crack trend, and comprehensively analyze the reasons for the deterioration of impact toughness caused by the changes of Mo content. The results show that the increase of Mo content leads to the formation of twinning martensite, which is one of the reasons for the deterioration of toughness. Mo is enriched at the interface of ferrite and M-A component, reducing the binding energy at the interface, resulting in the desorption of M-A component from the matrix, the formation of pores and becoming the nucleation site of cracks, resulting in the generation of micro-cracks and the decrease of toughness.

Mechanism of one-step hydrothermal nitric acid treatment for producing high adsorption capacity porous materials from coal gasification fine slag

The increasing amount of coal gasification fine slag (CGFS) necessitates its resource utilization. CGFS, mainly composed of porous carbonaceous particles and partially fused spherical or agglomerated ash particles, is an inexpensive and high-quality raw material for preparing adsorbent materials. However, the challenge remains in developing a simple, low-cost, and environmentally friendly method to produce high-performance porous materials from CGFS. In this study, a one-step treatment method using 2 mol/L nitric acid under hydrothermal conditions was proposed for CGFS. The adsorbent material (CGFS-2 M) prepared under a solid–liquid ratio of 2:5 and an initial concentration of 200 mg/L methylene blue (MB) exhibited an equilibrium adsorption capacity as high as 210.20 mg/g. The excellent adsorption performance of CGFS-2 M can be attributed to several factors: acid leaching for mineral removal and pore formation, resulting in a specific surface area and total pore volume 2.2 and 1.6 times that of untreated CGFS, respectively, and an optimized mesoporous pore size distribution favorable for MB adsorption; optimal mineral removal and a well-defined carbon microcrystal structure providing more space for MB adsorption; nitric acid treatment increasing the surface oxygen content and hydrophilicity, enhancing its ability to remove MB. The synergistic effect of pore structure improvement and surface modification indicates a feasible research direction for enhancing the performance of CGFS-based adsorbent materials. These results provide theoretical support for the development of efficient CGFS-based adsorbents.

Method for evaluation of Streptomyces growth and metabolism in the presence of glyphosate-based herbicide.

The use of pesticides, such as glyphosate, has increased due to population growth and the rising demand for food. Plant growth-promoting rhizobacteria (PGPR), such as Streptomyces, offer a more ecologically friendly alternative to the excessive use of pesticides. However, these bacteria undergo a complex life cycle involving the formation of hyphae, mycelia, and spores, which makes standardizing laboratory cultures challenging. In this context, we tested three methods for cultivating a Streptomyces isolate (CLV322) in the presence of the stressor agent glyphosate, denoted as M1, M2, and M3. These methods involved the simultaneous addition of the herbicide 24-48h after the start of cultivation. We evaluated the growth and cell viability of CLV322 using the 2,3,5-triphenyl tetrazolium chloride (TTC) assay under glyphosate-based herbicide stress (Roundup® Original DI) at concentrations ranging from 0.002 to 7.2mg mL- 1. We also assessed the ability of CLV322 to maintain PGPR characteristics in the presence of the herbicide by quantifying indolic compounds, siderophores, and phenazines. The cultivation method significantly influenced the production of metabolites by CLV322, with M3 yielding more consistent results across the evaluated parameters. Our findings suggest that germinating Streptomyces spores for 48h before introducing glyphosate (M3) enables the analysis of bacterial tolerance to herbicide stress. This methodology may also apply to evaluate other abiotic stresses on Streptomyces strains.

Cell shape and division septa positioning in filamentous Streptomyces require a functional cell wall glycopolymer ligase CglA.

The cell wall of monoderm bacteria consists of peptidoglycan and glycopolymers in roughly equal proportions and is crucial for cellular integrity, cell shape, and bacterial vitality. Despite the immense value of Streptomyces in biotechnology and medicine as antibiotic producers, we know very little about their cell wall biogenesis, composition, and functions. Here, we have identified the LCP-LytR_C domain protein CglA (Vnz_13690) as a key glycopolymer ligase, which specifically localizes in zones of cell wall biosynthesis in S. venezuelae. Reduced amount of glycopolymers in the cglA mutant results in enlarged vegetative hyphae and failures in FtsZ-rings formation and positioning. Consequently, division septa are misplaced leading to the formation of aberrant cell compartments, misshaped spores, and reduced cell vitality. In addition, we report our discovery that c-di-AMP signaling and decoration of the cell wall with glycopolymers are physiologically linked in Streptomyces since the deletion of cglA restores growth of the S. venezuelae disA mutant at high salt. Altogether, we have identified and characterized CglA as a novel component of cell wall biogenesis in Streptomyces, which is required for cell shape maintenance and cellular vitality in filamentous, multicellular bacteria.IMPORTANCEStreptomyces are our key producers of antibitiotics and other bioactive molecules and are, therefore, of high value for medicine and biotechnology. They proliferate by apical extension and branching of hyphae and undergo complex cell differentiation from filaments to spores during their life cycle. For both, growth and sporulation, coordinated cell wall biogenesis is crucial. However, our knowledge about cell wall biosynthesis, functions, and architecture in Streptomyces and in other Actinomycetota is still very limited. Here, we identify CglA as the key enzyme needed for the attachment of glycopolymers to the cell wall of S. venezuelae. We demonstrate that defects in the cell wall glycopolymer content result in loss of cell shape in these filamentous bacteria and show that division-competent FtsZ-rings cannot assemble properly and fail to be positioned correctly. As a consequence, cell septa placement is disturbed leading to the formation of misshaped spores with reduced viability.

Small-molecule GSDMD agonism in tumors stimulates antitumor immunity without toxicity

Gasdermin-mediated inflammatory cell death (pyroptosis) can activate protective immunity in immunologically cold tumors. Here, we performed a high-throughput screen for compounds that could activate gasdermin D (GSDMD), which is expressed widely in tumors. We identified 6,7-dichloro-2-methylsulfonyl-3-N-tert-butylaminoquinoxaline (DMB) as a direct and selective GSDMD agonist that activates GSDMD pore formation and pyroptosis without cleaving GSDMD. In mouse tumor models, pulsed and low-level pyroptosis induced by DMB suppresses tumor growth without harming GSDMD-expressing immune cells. Protection is immune-mediated and abrogated in mice lacking lymphocytes. Vaccination with DMB-treated cancer cells protects mice from secondary tumor challenge, indicating that immunogenic cell death is induced. DMB treatment synergizes with anti-PD-1. DMB treatment does not alter circulating proinflammatory cytokine or leukocyte numbers or cause weight loss. Thus, our studies reveal a strategy that relies on a low level of tumor cell pyroptosis to induce antitumor immunity and raise the possibility of exploiting pyroptosis without causing overt toxicity.

Alkali-etched mesoporous zeolite beta supported Ni nanoparticles for the catalytic hydrocracking of Shenfu subbituminous coal to hydrocarbon-rich oils

The conversion of low-rank coal to hydrocarbons by catalytic hydrocracking (CHC) is an important process in chemical industry. However, obtaining hydrocarbon-rich oils directly from low-rank coal by precise removal of heteroatoms remains a huge challenge. Considering this fact, a novel bifunctional catalyst Ni10%@βE was prepared by alkali-etching and used for the CHC of Shenfu subbituminous coal (SC). Alkali-etching modified L/B acid distribution and promoted the formation of hierarchical pores in βE, which helps to improve the catalytic activity. Benzyloxybenzene can be selectively converted to benzene and toluene with a total yield of 184.3 mol% over Ni10%@βE. Under 1 MPa H2, 300 °C, and 2 h, the yield of SC-derived cracking oil increased from 8.6 % to 18.0 %, and the proportions of aliphatic hydrocarbons and arenes increased from 13.5 % and 41.9 % to 32.4 % and 63.6 %, respectively. Modification of βE by alkali-etching changes the H2 activation activity of Ni10%@βE. Synergetic transfer of H···H, δ+H···Hδ-, H+, and H· is the core of obtaining high-yield hydrocarbons from SC.

Antagonism of rhizosphere Trichoderma brevicompactum DTN19 against the pathogenic fungi causing corm rot in saffron (Crocus sativus L.) in vitro.

Corm rot in saffron (Crocus sativus L.) significantly impacts yield and quality. Non-toxic fungi, particularly Trichoderma species, are valuable for biological control due to their production of diverse and biologically active secondary metabolites. This study aimed to isolate an effective antagonistic fungus against the pathogenic fungi causing corm rot in saffron. Four pathogenic fungi (Fusarium oxysporum, Fusarium solani, Penicillium citreosulfuratum, and Penicillium citrinum) were isolated from diseased saffron bulbs in Chongming. Initial screening through dual culture with these pathogens re-screening from rhizosphere soil samples of C. sativus based on its inhibitory effects through volatile, nonvolatile, and fermentation broth metabolites. The inhibitory effect of biocontrol fungi on pathogenic fungi in vitro was evaluated by morphological observation and molecular biology methods. Antagonistic fungi were identified as Trichoderma brevicompactum DTN19. F. oxysporum was identified as the most severe pathogen. SEM (scanning electron microscope) and TEM (transmission electron microscope) observations revealed that T. brevicompactum DTN19 significantly inhibited the growth and development of F. oxysporum mycelium, disrupting its physiological structure and spore formation. Additionally, T. brevicompactum DTN19 demonstrated nitrogen fixation and production of cellulase, IAA (Indole acetic acid), and siderophores. Whole-genome sequencing of strain DTN19 revealed genes encoding protease, cellulase, chitinase, β-glucosidase, siderophore, nitrogen cycle, and sulfate transporter-related proteins. T. brevicompactum DTN19 may inhibit the propagation of pathogenic fungi by destroying their cell walls or producing antibiotics. It can also produce IAA and iron carriers, which have the potential to promote plant growth. Overall, T. brevicompactum DTN19 showed the development prospect of biological agents.

Microstructure analysis of cement-biochar composites

The use of biochar as a concrete constituent has been proposed to reduce the massive carbon footprint of concrete. Due to the low density and complex porosity of biochar, microstructural analysis of Portland cement-biochar composites is challenging. This causes challenges to the improvement of the micro-scale understanding of biochar composite behavior. This work advances the microstructural understanding of Portland cement composites with 0, 5, and 25 volume percent (vol%) of cement replaced with wood biochar by applying common characterization techniques of mercury intrusion porosimetry (MIP), gas sorption, scanning electron microscopy, and isothermal heat flow calorimetry (HFC) in conjunction with 1H nuclear magnetic resonance (NMR) and micro-X-ray computed tomography (XCT) analysis techniques. The combination of these techniques allows a multi-scale investigation of the effect of biochar on the microstructure of cement paste. NMR and XCT techniques allow the observation and quantification of the pore space. HFC and MIP confirmed that biochar absorbs moisture and reduces the effective water-cement ratio. Gas sorption, MIP, and NMR shows that 5 vol% replacement does not significantly affect the gel and capillary pore structures. Results from XCT (supported by MIP and NMR) show that biochar can reduce the formation of larger pores. Importantly, XCT results suggest that biochar can act as a flaw in the microstructure which could explain reductions in the mechanical properties. Overall, the mechanical properties already analyzed in the literature are consistent with the microstructural changes observed, and these results highlight the need to carefully tailor the volume fraction of biochar to control its effect on the paste microstructure.

Phase-Field Modeling of Kinetics of Diffusive Phase Transformation in Compositionally-Graded Ni-Based Superalloys

AbstractKinetics of the $$\gamma$$ γ /$$\gamma ^{\prime}$$ γ ′ phase transformation and the interdiffusion phenomena in single-crystal Ni-based superalloys, under isothermal annealing and composition gradient, is investigated through the phase-field and continuum diffusion models. The employed models in the present work exploit CALPHAD-based thermodynamics and kinetics databases, in order to perform realistic simulations. We specifically predict the interdiffusion of elements for a hypothetical alloy AlCoCrTaNi/Ni diffusion couple, equivalent to the CMSX-10/Ni diffusion couple, at 1323 K. Accordingly, the phase fraction and morphology of $$\gamma ^{\prime}$$ γ ′ precipitations in the $$\gamma$$ γ matrix is simulated as well. The implemented multi-component diffusion model takes into account vacancies and pore formation, reflecting Kirkendall effect. Furthermore, the time evolution of morphology parameters of the precipitate-depleted zone in the diffusive region (i.e., the position and the size) are estimated.

Investigation of effects of environmental conditions on wear behaviors of glass fiber reinforced polyester composite materials

AbstractGlass fiber reinforced polymer (GFRP) composites can be subjected to different environmental conditions such as temperature, humidity, ultraviolet radiation, hydrothermal cycle, acidic and alkaline solution in environments where they operate. These environmental conditions cause different damage mechanisms in composites such as pore formation, micro‐cracks, delamination, fiber breakage, fiber/matrix interface separation, plasticization, swelling and surface color change. In this study, wear properties of hybrid glass fiber reinforced polymer composites exposed to various environmental conditions for constant load (60 N), speed (500 rpm) and 2 h were examined comprehensively, depending on material content and environmental conditions. In this experimental study, the service conditions in glass fiber reinforced composites were simulated using different artificial aging environments such as acidic environment, hydrothermal cycle and UV radiation. In addition to the material content, it appears that the environmental conditions to which composites are exposed has a significant effect on friction coefficient. Considering environmental conditions, it is seen that the acid environment and hydrothermal cycle have reduced wear resistance of GFRP composites, while UV radiation improved wear resistance of the composites. In C2 sample, the wear rates under different conditions are 1.87 × 10−14 m3/Nm in non‐treated sample, 6.05 × 10−14 m3/Nm in acid environment, 4.79 × 10−14 m3/Nm in hydrothermal cycle and 0.59 × 10−14 m3/Nm in UV radiation.Highlights Friction coefficient of glass fiber reinforced polyester (GFRP) is higher under aged condition compared to non‐treated. Glass fibers used in correct proportions can reduce friction coefficient in GFRP. GFRP exposed to environmental conditions has an important effect on wear. Acid environment and hydrothermal cycle has reduced wear resistance of GFRP. UV radiation improved wear resistance of GFRP composite.

PM2.5 Induces Pyroptosis via Activation of the ROS/NF-κB Signaling Pathway in Bronchial Epithelial Cells.

Background and Objectives: Fine particulate matter, PM2.5, is becoming a major threat to human health, particularly in terms of respiratory diseases. Pyroptosis is a recently discovered and distinct form of cell death, characterized by pore formation in the cell membrane and secretions of proinflammatory cytokines. There has been little research on the effect of PM2.5 on pyroptosis, especially in airway epithelium. We investigated whether PM2.5-related oxidative stress induces pyroptosis in bronchial epithelial cells and defined the underlying mechanisms. Materials and Methods: After exposure of a BEAS-2B cell line to PM2.5 concentration of 20 µg/mL, reactive oxygen species (ROS) levels, parameters related to pyroptosis, and NF-κB signaling were measured by Western blotting, immunofluorescence, and ELISA (Enzyme-linked immunosorbent assay). Results: PM2.5 induced pyroptotic cell death, accompanied by LDH (Lactate dehydrogenase) release and increased uptake of propidium iodide in a dose-dependent manner. PM2.5 activated the NLRP3-casp1-gasdermin D pathway, with resulting secretions of the proinflammatory cytokines IL-1β and IL-18. The pyroptosis activated by PM2.5 was alleviated significantly by NLRP3 inhibitor. In PM2.5-exposed BEAS-2B cells, levels of intracellular ROS and NF-κB p65 increased. ROS scavenger inhibited the expression of the NLRP3 inflammasome, and the NF-κB inhibitor attenuated pyroptotic cell death triggered by PM2.5 exposure, indicating that the ROS/NF-κB pathway is involved in PM2.5-induced pyroptosis. Conclusions: These findings show that PM2.5 exposure can cause cell injury by NLRP3-inflammasome-mediated pyroptosis by upregulating the ROS/NF-κB pathway in airway epithelium.

Uncovering the membrane and pore formation mechanisms of the lysozyme membrane made via the amyloid-like assembly

Biomimetic protein membranes have attracted increasing interests because of their distinctive separation properties in the membrane field. Low-cost and stable protein lysozyme has been intensively invetigated to fabricate high-performance sepration membranes via a facile and scalable method of amyloid-like assembly. However, the pore formation mechnism of the lysozyme membrane remains unclear. Herein, the lysozyme membranes were fabricated and the membrane formation mechnism and separation properties were investigated experimentally. Molecular dynamics simulation (MDS) was also employed to reveal the pore formation mechanism of the lysozyme membrane. The fabricated lysozyme membrane achieved a stable high water permeance of 10.2 L m−2 h−1 bar−1, as well as a relatively high separation factor (9.5) towards antibiotic and sodium chloride. MDS results found that the membrane pore size is governed by the amino acid compositions and is negatively dependent on the intermolecular forces among amino acids around the pores. Selective pores with 0.54 nm in diameter are primarily formed by these amino acids including alanine (35 %), aspartic acid (25 %), arginine (15 %), phenylalanine (11 %), and lysine (7 %), in which half of them have hydrophobic side chains with no charge, and another half have hydrophilic side chains with balanced charges. This work may stimulate the development of highly permeable and selective protein membranes by carefully engineering their amino acid compositions with optimal charges and hydrophobicity for generation of numerous selective pores.

Preparation and characterization of potassium hydroxide activated hydrochar

This paper presents processing and characterization of hydrochar derived from bamboo via hydrothermal carbonization at 200 °C for 4 h followed by activation at 600 °C for 2 h. The hydrochar contains hierarchical pores. The BET surface area of the hydrochar activated by KOH reached 4.5506 m2/g. KOH enhanced pore and nanofiber formation. All the bamboo-derived hydrochars can effectively harvest solar energy to evaporate seawater. The KOH-activated one showed the best performance with the maximum evaporation rate of 3.057 kg/(m2∙h).

Microstructural analysis and defect characterization of additively manufactured AA6061 aluminum alloy via laser powder bed fusion

AA6061 is a widely used aluminum alloy with significant applications in the aerospace and automotive industries. Despite its popularity, the utilization of additively manufactured AA6061 through the laser powder bed fusion (LPBF) process has been hindered by the pronounced formation of pores and cracks during rapid solidification. This study quantitatively investigated defects, including pores and cracks, and microstructures, including texture, grain size, subgrain structure, and precipitates, of LPBF-manufactured AA6061 across a broad spectrum of laser power and speed combinations. A high relative density of more than 99 % was achieved with a low-power and low-speed condition, specifically 200 W and 100 mm/s, with minimal cracks. Large pores, akin to or exceeding melt pool dimensions, emerged under either low or high energy densities, driven by the lack of fusion and vaporization/denudation mechanisms, respectively. Solidification cracks, confirmed by the fractography, were propagated along grain boundaries and are highly dependent on laser scanning speed. Elevated power and speed exhibited finer grain size with refined subgrain cellular structures and increased precipitates at interdendritic regions. The cooling rate and thermal gradient estimated from thermal analytical solutions explain the microstructures’ characteristics. Nano-sized Si-Fe-Mg enriched precipitates are confirmed in both as-built and heat-treated conditions, whereas T6 heat treatment promotes a uniform distribution with coarsening of those precipitates. The low-power and low-speed conditions demonstrated the highest yield strength, consistent with defect levels. A minimum of 102.3 % increase in yield strength with reduced ductility was observed after heat treatment for all examined conditions. This work sheds light on printing parameters to mitigate the formation of pores and cracks in additively manufactured AA6061, proposing a process window for optimized fabrication and highlighting the potential for enhanced material properties and reduced defects through process control.