Flux Levels Research Articles

Study on the effect of structural parameters of a thermal liner on its thermal protective performance under radiant heat exposure

To comprehend the impact of elementary construction parameters of nonwoven thermal liners on their thermal protective performance, the current research primarily emphasizes on studying the effect of needle penetration depth and needle punch density of the thermal liner. Nonwoven fabrics with three different punch densities and three needling depths were prepared. The air permeability and thermal resistance of the thermal liner were investigated through regression analysis to determine the influence of needle penetration depth and needle punch density. It was observed that both factors had a notable impact on the air permeability and thermal resistance of the thermal liner. An increase in needle penetration depth and needle punch density resulted in a decrease in the air permeability and thermal resistance of the thermal liner. An experiment was carried out utilizing the 33 Box-Behnken designing approach; the factors employed were the radiant heat flux intensity, needle punch density, and needle penetration depth of the thermal liner. The thermal protective performance of thermal liners was measured at three discrete intensities of radiant heat exposures. To investigate the effect of the test and construction parameters and their interaction, an analysis of variance study was carried out. It was observed that protection time rises with the decrease in needling depth and needle punch density at every level of heat flux. With the rise in incident radiant heat flux, protection time declines, irrespective of needle penetration depth and punch density levels.

Highly inhomogeneous interactions between background climate and urban warming across typical local climate zones in heatwave and non-heatwave days

Abstract Urban heat island (UHI) in conjunction with heatwave (HW) leads to exacerbation of thermal stress in urban areas. Prior research on UHI and HW has predominantly concentrated on examining the thermal conditions at the surface and near-surface, with few investigations extending to the radiative and dynamical interactions of UHI and HW, particularly with a focus on the inhomogeneities across local climate zones (LCZs). Here, we analyse the temperature disparity between HW and non-HW conditions across LCZs in the Sydney area by quantifying the contributions of individual radiative and dynamical processes using the coupled surface-atmosphere climate feedback-response analysis method (CFRAM). Three moist HW events in 2017, 2019, and 2020 are simulated using the Weather Research and Forecasting (WRF) model coupled with the single-layer urban canopy model (SLUCM). It is found that the maximum surface and 900 hPa temperature difference between HW and non-HW days may reach up to 10 K, with the increased net solar radiation during HWs being comparable to the typical level of anthropogenic heat flux in urban areas. It is also found that the reduction of clouds, the presence of vapour, and the increase of sensible heat contribute to the warming effect to various degrees, with the contribution of clouds being the most dominant. Conversely, the generation of dry convection and the increase of latent heat flux lead to cooling effects, with the latter being more dominant and capable of causing up to 10 K surface temperature difference between LCZ1 (compact high-rise) and LCZ9 (sparsely built). The differences in the contributions of climate feedback processes across different LCZs become more evident during more severe and humid HWs. These findings underscore the necessity of implementing LCZ-tailored heat mitigation strategies.

Improving oral absorption of a rapidly crystallizing parent drug using prodrug strategy: Comparison of phosphate versus glycine based prodrugs

With an increasing number of Biopharmaceutical Classification System (BCS) II/IV pipeline compounds, solubilizing and supersaturating formulation strategies are becoming prevalent. Beyond formulation and solid form strategies, prodrugs are also employed to overcome solubility-limited absorption of poorly water-soluble compounds. Prodrugs can potentially yield supersaturated systems upon conversion to the parent drug intraluminally and thus enhance absorption. However, supersaturation also increases the driving force for crystallization, resulting in low solution concentrations, which can potentially negate the advantage of prodrugs. In this work, two unique solubility-enhancing prodrugs, phosphate and glycine esters, were investigated for a rapidly crystallizing parent drug. Ex vivo absorption studies using rat tissue and in vivo studies in dogs were performed. Conversion rate of the phosphate prodrug to the parent was dependent on the milieu and increased ∼24-fold in the presence of intestinal contents as medium and tissue relative to neat buffer. In contrast, conversion of the glycine prodrug was minimal under any conditions tested, suggesting that the conversion occurs after absorption into the enterocytes. Phosphate prodrug showed a non-linear increase in parent drug absorptive flux across rat intestinal tissue with concentration when intestinal contents were used as donor media. This was attributed to rapid conversion and high supersaturation of the parent drug which subsequently resulted in crystallization at high doses in the donor chamber. Glycine prodrug did not undergo complete conversion at high doses and was absorbed unchanged on the basolateral side, indicating saturation of the converting enzymes in the enterocytes. The combined flux (parent drug and glycine) showed a linear increase with dose and crystallization was not observed. Under physiological conditions, glycine prodrug that is absorbed unchanged from the intestine can potentially undergo complete conversion in hepatocytes after absorption and make the parent drug systemically available. Thus, glycine prodrug provided overall higher absorption compared to phosphate prodrug. The observed flux levels for both the prodrugs were higher compared to the parent drug alone, highlighting an advantage to use of a prodrug strategy to improve absorption of such compounds. Oral dosing in a dog PK study revealed that the bioavailability using the phosphate prodrug was ∼50% whereas, it was ∼100% with glycine prodrug, supporting the in vitro observations.

Exploring the Broadband Spectral and Timing Characteristics of GRS 1915+105 with AstroSat and NICER Observations

In this study, we undertake a spectral-timing analysis of the black hole X-ray binary source GRS 1915+105 using simultaneous observations carried out by AstroSat (Large Area X-ray Proportional Counter, LAXPC and Soft X-ray Telescope, SXT) and Neutron Star Interior Composition Explorer (NICER) in 2017. The source showed two flux levels (high and low), whose energy spectra can be described by the thermal comptonization of disk photons. The spectral parameters obtained by the joint fitting of SXT/LAXPC and NICER/LAXPC were consistent. The power density spectra from LAXPC and NICER revealed a broad, prominent feature at ∼2 Hz. The energy dependence of the fractional rms and time lag of this feature cannot be explained by only variations of coronal spectral parameters. Instead, a model where the coronal heating rate varies first and induces a change in the disk temperature and inner radius can explain the variation. Our results underline the importance of simultaneous observations by AstroSat and NICER and highlight the need for more sophisticated models to explain the spectral-temporal behavior of black hole systems.

Longitudinal Variations of Energetic Electrons Scattered by NWC Transmitter: DEMETER Observations

AbstractLow‐Earth orbit (LEO) satellites often observe wisp‐like energy spectra, characterized by lower energies at higher L values of energetic electrons, resulting from the scattering effect of the narrow‐band artificial transmitter signals. Typically, the flux levels of wisp energy spectra increase as they approach the South Atlantic Anomaly (SAA). Here, we report, for the first time, the longitudinal variations of wisp positions in the energy‐L coordinate based on observations from the DEMETER satellite. The L‐values of wisps decrease at the longitudes <180° and increase at the longitudes >180°. By considering the satellite's orbital characteristics, we found that the longitudinal variations of wisp are essentially the MLT‐dependent radial transport of electrons. This finding indicates that the electron drift paths can be modified within a single drift period. We propose a duskward convection electric field as a potential mechanism to explain the longitudinal variations of wisps. By assuming a uniform duskward convection electric field with an amplitude of ∼1.5 mV/m, our simulations can reasonably reproduce the longitudinal variations of wisps observed in the southern hemisphere on 21 March 2009. Our results support the existence of a convection electric field in the inner belt and suggest that this electric field significantly contributes to the variations in energies and L values of energetic electrons within one drift period.

The Accelerating Decline of the Mass Transfer Rate in the Recurrent Nova T Pyxidis* * Based on observations made with the NASA/ESA Hubble Space Telescope, obtained from the data archive at the Space Telescope Science Institute. STScI is operated by the Association of University for Research in Astronomy, Inc. under NASA contract NAS 5-26555.

The recurrent nova T Pyxidis (T Pyx) has erupted six times since 1890, with its last outburst in 2011, and the relatively short recurrence time between classical nova explosions indicates that T Pyx must have a massive white dwarf (WD) accreting at a high rate. It is believed that, since its outburst in 1890, the mass transfer rate in T Pyx was very large due to a feedback loop where the secondary is heated by the hot WD. The feedback loop has been slowly shutting off, reducing the mass transfer rate, and thereby explaining the magnitude decline of T Pyx from ∼13.8 (before 1890) to 15.7 just before the 2011 eruption. We present an analysis of the latest Hubble Space Telescope far-ultraviolet and optical spectra, obtained 12 yr after the 2011 outburst, showing that the mass transfer rate has been steadily declining and is now below its preoutburst level by about 40%: Ṁ∼1−3×10−7M⊙ yr−1 for a WD mass of ∼1.0–1.4 M ⊙, an inclination of 50°–60°, reddening of E(B − V) = 0.30 ± 0.05, and a Gaia Data Release 3 distance of 2860−471+816 pc. This steady decrease in the mass transfer rate in the ∼decade after the 2011 outburst is in sharp contrast with the more constant preoutburst ultraviolet continuum flux level from archival International Ultraviolet Explorer spectra. The flux (i.e., Ṁ ) decline rate is 29 times faster now in the last ∼decade than observed since 1890 to ∼2010. The feedback loop shut off seems to be accelerating, at least in the decade following its 2011 outburst. In all eventualities, our analysis confirms that T Pyx is going through an unusually peculiar short-lived phase.

Inactivation kinetics of dairy phages using photocatalytic paint under diverse environmental conditions and radiation sources

This article investigates the efficacy of a photocatalytic paint for bacteriophages inactivation under various levels of incident radiation flux, relative humidity and radiation sources. Two phages that infect lactic acid bacteria were selected: J-1, infective of Lacticaseibacillus casei ATCC 27139, and M13-G1b, infective of Streptococcus thermophilus G1b. Phage suspensions were deposited on coated and uncoated plates and exposed to radiation typically used for indoor illumination (λ = 360–720 nm). A first-order inactivation kinetics was proposed with respect to the Plaque Forming Units per mL (PFU/mL) that correlates the inactivation constant with the operating conditions. The kinetic constant of this novel model combines a potential function for the incident radiation flux and a logistic function for the relative humidity. The results showed that as these variables increased, phage inactivation turned higher for both uncoated and coated plates. Photonic and quantum efficiencies were also calculated for both phages, when treated with photocatalytic paint under UV-A radiation. The photonic efficiencies were 8.03 × 1012 PFU/Einstein for J-1 and 4.05 × 1012 PFU/Einstein for M13-G1b, while the quantum efficiencies were 1.19 × 1013 PFU/Einstein for J-1 and 6.03 × 1012 PFU/Einstein for M13-G1b. Good agreement was obtained between predictions of the proposed kinetic model and experimental data, with a Root Mean Square Error of 4.43 % for J-1 and 2.98 % for M13-G1b. The developed model would be useful to predict phage inactivation under diverse combinations of operating conditions levels in environments of dairy plants, different from those tested in this work.

Molecular dynamics method to investigate the interaction energy and mechanical properties of the reinforced graphene aerogel with paraffin as the phase change material in the presence of different external heat fluxes

BackgroundGraphene aerogels (GA), known for their exceptional lightweight and sturdy characteristics, present a promising avenue for improving thermal energy (TE) storage and transfer efficiency. It might be possible to make better thermal management systems in fields like electronics, aerospace, and energy storage by studying how heat flux (HF) affects the strength and stability of graphene aerogels. MethodsThe study used molecular dynamics (MD) simulation to investigate how the mechanical properties of graphene aerogels strengthened with paraffin as phase change material (PCM) change in response to external heat flux (EHF). These simulation methods provided a detailed view of molecular interactions and dynamics at the atomic level, allowing researchers to understand the behavior of materials under various conditions. The change in toughness, interaction energy (IE), Young's modules (YM), and ultimate strength (US) was examined for this reason. Significant findingsThe results indicate that when the HF increased from 0.1 to 0.3 W/m2, the ultimate strength and Young's modules increased from 8.91 and 5.37 GPa to 14.546 and 8.59 GPa, respectively. These values declined when HF increased by more than 0.3 W/m2. When EHF went up to 0.3 W/m², these graphene aerogel properties went up. This was because the atoms moved around more and there were more bonding contacts among the graphene sheets, which made the structure of material stronger. However, at heat flux levels exceeding 0.3 W/m², excessive thermal energy may lead to thermal degradation, causing bond breakage and loss of structural integrity, ultimately resulting in a decrease in these mechanical properties. Also, the results reveal that interaction energy increased from -1522.098 to -1546.325 eV as external HF increased to 0.3 W/m2. The thermal motion of atoms enhanced as the HF increased, enabling closer clustering and better alignment of graphene sheets, thereby strengthening their interactions. This study gave us useful information about how to improve the mechanical properties of graphene aerogels in different HF conditions. This made it more likely that these materials can be used in energy storage systems and thermal management.

Proteoglycan 4 (Lubricin) and Regulation of Xanthine Oxidase in Synovial Macrophage as A Mechanism of Controlling Synovitis.

Synovial macrophages (SMs) are important effectors of joint health and disease. A novel Cx3CR1 + TREM2 + SM population expressing the tight junction protein claudin-5, was recently discovered in synovial lining. Ablation of these SMs was associated with onset of arthritis. Proteoglycan 4 (PRG4) is a mucinous glycoprotein that fulfills lubricating and homeostatic roles in the joint. The aim of this work is to study the role of PRG4 in modulating synovitis in the context of SM homeostasis and assess the contribution of xanthine oxidase (XO)-hypoxia inducible factor alpha (HIF-1α) axis to this regulation. We used Prg4 FrlioxP/FrtloxP ;R26 FlPoER/+ , a novel transgenic mouse, where the Prg4 Frt allele normally expresses the PRG4 protein and was designed to flank the first two exons of Prg4 with a flippase recognition target and "LOXP" sites. Inducing flippase activity with tamoxifen (TAM) inactivates the Frt allele and thus creates a conditional knockout state. We studied anti-inflammatory SMs and XO by quantitative immunohistochemistry, isolated RNA and studied immune pathway activations by multiplexed assays and isolated SMs and studied PRG4 signaling dysfunction in relation to glycolytic switching due to pro-inflammatory activation. Prg4 inactivated mice were treated with oral febuxostat, a specific XO inhibitor, and quantification of Cx3CR1 + TREM2 + SMs, XO immunostaining and synovitis assessment were conducted. Prg4 inactivation induced Cx3CR1 + TREM2 + SM loss (p < 0.001) and upregulated glycolysis and innate immune pathways in the synovium. In isolated SMs, Xdh (p < 0.01) and Hif1a (p < 0.05) were upregulated. Pro-inflammatory activation of SMs was evident by enhanced glycolytic flux and XO-generated reactive oxygen species (ROS). Febuxostat reduced glycolytic flux (p < 0.001) and HIF-1α levels (p < 0.0001) in SMs. Febuxostat also reduced systemic inflammation (p < 0.001), synovial hyperplasia (p < 0.001) and preserved Cx3CR1 + TREM2 + SMs (p < 0.0001) in synovia of Prg4 inactivated mice. PRG4 is a biologically significant modulator of synovial homeostasis via inhibition of XO expression and downstream HIF-1a activation. PRG4 signaling is anti-inflammatory and promotes synovial homeostasis in chronic synovitis, where direct XO inhibition is potentially therapeutic in chronic synovitis.

Analysis of an evaporator with single horizontal circular micro-tube using FC-72 as working fluid for electronic cooling applications

Flow boiling in micro-channels is one of the most efficient methods for heat rejection in electronics, necessitating proper system design. Numerical simulations are the most suitable tool for this purpose, with most literature focusing on CHF situations, while few studies address conditions bellow it. This paper presents a parametric analysis of an evaporator with a horizontal circular micro-tube, maintaining a fixed outlet quality, using numerical simulation. The simulation employs a one-dimensional steady-state model with FC-72 as the working fluid, considering both subcooled liquid and two-phase lengths, computed using theoretical equations and correlations. The effects of inner tube diameter, heat flux, inlet pressure, and subcooling level on key evaporator design parameters are discussed in detail. Results indicate that to minimize hydraulic pumping power, fluid temperature difference, and inlet temperature are required, the evaporator should operate with the lowest heat flux (50kW∙m-2), the largest inner tube diameter (1.3mm), the highest subcooling level (30K), and the lowest inlet pressure (2bar). Under these conditions, hydraulic pumping power can be reduced by up to 86%. Furthermore, to achieve the minimum fluid temperature difference along the tube (approximately 4.9K) and avoid CHF situation, operation with the lowest subcooling level (5K) is necessary. Finally, the ratio of the heat flux to the critical heat flux, q"/CHF, increases with rising inlet pressure and subcooling level, and/or decreasing inner tube diameter. The minimum q"/CHF ratio of 43.9% was obtained at pin=2bar, q"=50kW∙m-2, D=0.9mm, and ΔTsub=5K. These findings provide insights into optimal design parameters for evaporators in micro-electronics cooling applications.

Burning and flame extinction patterns of PMMA under external heating and oxygen deficiency

The paper presents an experimental study investigating the impact of under-oxygenated conditions on the burning characteristics and flame extinction of horizontal transparent poly(methyl-methacrylate) (PMMA) slabs subjected to external heating. Small-sized solids are exposed to various constant levels of radiant heat flux in a nitrogen-diluted environment at ambient pressure. The study aims to understand the multivariable dependence of PMMA combustion on oxygen and heating levels. The analysis goes beyond the study of global and local variables to provide an understanding of the mechanisms involved, revealing a notable effect on burning characteristics and flame extinction mechanisms by blow-off. The results provide a detailed assessment of the surface energy balance and flame bulk properties. The results demonstrate good repeatability up to a certain oxygen limit, beyond which the flame combustion regime exhibits stochastic behaviour. The study of heat transfer mechanisms has revealed that flame radiation and external heating play a predominant role in the heating of horizontal solid fuels, In contrast, within the flame, convection is the main contributor to solid heating, rather than flame radiation. Solid characteristics show linear trends proportional to oxygen depletion, while gas phase characteristics show monotonic trends strongly influenced by the changing combustion regime. The surface temperature of the solid is highly sensitive to the test conditions that affect the energy balance. Dimensionless parameters are developed and data are correlated with existing literature. The analysis demonstrates that the linear or monotonic trends are maintained regardless of external heating. Finally, models are proposed and validated to predict both the extinction limit and the burning rate independently of irradiance and oxygen levels.

Computational fluid dynamics simulation of cryogenic vertical upflow boiling under Earth gravity

This study presents numerical simulations and their validation for flow boiling of liquid nitrogen (LN2) in a vertical upflow orientation, with a primary aim to understand the complex two-phase flow and heat transfer phenomena important to space applications. The computational fluid dynamics (CFD) model utilized the coupled level set volume of fluid (CLSVOF) method, incorporating additional source terms for bubble collision dispersion force and shear lift force in the momentum conservation equation to enhance simulation accuracy. The simulations were conducted for two mass velocities (G = 526 and 804 kg/m2s) and three different heat flux levels (approximately 10%, 30%, and 70% of critical heat flux (CHF) under Earth gravity. The model was validated against measured wall temperature data acquired from the authors’ previous experimental studies, demonstrating average deviations of less than 2.8 K across all operating conditions. The simulated two-phase flow contours illustrated various flow patterns, including bubbly, slug, churn, and annular. Both mass velocity and heat flux were observed to impact the onset of nucleate boiling (ONB), bubble nucleation, growth, and coalescence, and overall vapor structure. The simulations also offered insight into axial and radial void fraction and velocity profiles, revealing local flow acceleration trends synchronized with void fraction development. A comparison between predicted and measured bulk fluid temperature profiles showed excellent agreement, further validating the CFD model’s accuracy and practical usefulness for two-phase cryogenic flow boiling simulations in space applications.

Varying Light Intensities Affect Lettuce Growth and Physiology in Controlled Indoor Environments

Agriculture in controlled environments has gained popularity over time. Compared to traditional agriculture, controlled environments emerge as an alternative to mitigate the negative impacts of conventional farming methods. However, controlled environment agriculture, particularly plant factories with artificial lighting, incurs higher electricity costs, primarily for supplemental lighting and dehumidification of the cultivation area. Given these high costs, it is crucial to understand how efficiently plants utilize available light to convert it into biomass. This understanding can be used to design lighting strategies to reduce electricity usage. In this study, we cultivated ‘Rex’ lettuce (Lactuca sativa) plants on a soilless substrate and used an ebb-and-flow system for irrigation and fertilization. Plants grew in varying photosynthetic photon flux density (PPFD) levels ranging from 125 to 375 µmol·m−2·s−1 and were assessed for various physiological responses. Our findings revealed that plants exposed to higher light levels exhibited greater final dry weight, increased photosynthetic activity, higher water use efficiency, and accelerated growth compared to those under lower light conditions. Notably, plants subjected to higher light intensities did not show a significant increase in transpiration, suggesting a potential trade-off between energy expenditure on supplemental lighting and dehumidification. This finding opens the possibility of reducing energy consumption for dehumidification and achieving economic savings by subjecting plants to optimal growing conditions for shorter durations. This depends on whether higher savings on dehumidification are achieved compared to the energy required to maintain high PPFD levels.

Development of Readily Available &amp; Robust High Heat Flux Gardon Gauges

Concentrated solar power (CSP) technologies deliver concentrated solar energy as a heat source to industrial processes, power generation cycles, and chemical cycles. CSP systems require accurate and reliable high flux measurements, and next generation CSP systems will require flux measurement up to 1000 W/cm2. Existing flux measurement devices do not comprehensively meet the flux rating, cycle life, cost, and lead-time needs of stakeholders, necessitating the development of an improved flux sensor. In this study, Sandia National Laboratories (SNL) partnered with Hukseflux Thermal Sensors to develop a low-cost, short lead-time, and robust flux sensor rated to 250 W/cm2. Three prototype circular foil gauge designs were assessed for performance at the National Solar Thermal Test Facility (NSTTF) at SNL. Each gauge design measured flux up to 250 W/cm2 with &lt;5% measurement error. Following baseline error quantification, gauges were exposed to flux above 500 W/cm2 to assess gauge failure mechanisms. Gauges physically survived &gt;500 W/cm2 flux exposure, but measurement error was found to increase after foil coatings reached 400 °C. The results of this study suggest that coating optical properties change at excessive temperatures and that foil coating temperature, rather than heat flux level, dictates the acceptable gauge measurement range.

Study of the fuel irradiation capsule using NEPTUNE_CFD software

The Fuel Irradiation Capsule (FUICA) is an experimental device designed to irradiate fuel elements in a Material Testing Reactor (MTR) during long period. This component is being studied for implementation in the Jules Horowitz reactor (RJH) under construction in France (1).Its function is to irradiate and to cool fuel sample on a passive way by transferring the thermal energy generated to the device periphery, through an annular zone of confined and pressure-regulated water (2). Its external wall, kept cold by the reactor cooling circuit, allows for the heat extraction. Natural convection is the driving force for the heat transfer between the fuel element and the cold wall of the device. By eliminating any internal forced convection cooling system, the device becomes relatively simple and cost-effective.This paper describes the device modeling carried out using the NEPTUNE_CFD software (3). The present work, in its first part, focuses on the behavior of the device depending on the heat flux, and in its second part, the sensitivity to boundary conditions. The objective is to provide a way to design and optimize the fuel capsule thermal characteristics. For that, an arbitrary size of fuel capsule is chosen in order to analyze the physics involved. A sensitivity study is then presented in order to highlight the influence of the physical parameters on the fuel capsule performance.Three operating ranges for the heat transfer are exhibited in this study: moderate in the liquid phase, the heat transfer becomes optimal in the two-phase regime, and even improves with the level of heat flux before deteriorating abruptly for high flux called Critical Heat Flux (CHF). Two observations also arise to improve thermal transfer: in the liquid phase, it is necessary to reduce the water thickness to improve convection, and in the two-phase regime, the heat transfer increases proportionally to the heat flux. In the end, the irradiation capsule is capable of extracting very high heat flux.

Melanin resistance of heat-processed ginsenosides from Panax ginseng berry treated with citric acid through autophagy pathway

GFRS is the conversion product of Panax ginseng Meyer berry after citric acid heat treatment, which is rich in rare ginsenosides. However, the anti-melanin role of GFRS in the regulation of skin pigmentation and its material basis remains unclear. To compare the anti-melanin activity before and after citric acid heat treatment, we determined the effects of GFS and GFRS on tyrosinase activity and melanin lever under α-MSH stimulation and found the potential anti-melanin effect of GFRS. Further, Western blot and immunofluorescence methods were used to reveal the mechanism by which GFRS detects anti-melanin activity by promoting autophagy flux levels. In zebrafish models, GFRS inhibited endogenous melanin and tyrosinase better than arbutin and promoted the accumulation of autophagy levels in vivo. To determine the material basis of the anti-melanin effect of GFRS, HPLC was used to isolate and prepare 12 ginsenosides from GFRS, and their activity evaluation and structure–activity relationship analysis were performed. The results showed that the inhibitory effect of GFRS on melanin was Rg3 > Rg5 > Rk1 > Rd. Molecular docking showed that their docking fraction with mushroom tyrosinase was significantly better than that of arbutin, but the presence of C-20 glycosylation decreased the anti-melanin activity of Rd. To maximize the content of Rg3, Rg5, and Rk1, we optimized the process by using citric acid heat treatment of ginsenoside Rd and found that citric acid heat treatment at 100°C almost completely transformed Rd and obtained a high content of active ingredients. In summary, our data demonstrated that GFRS exerted anti-melanin effects by inducing autophagy. It was further revealed that Rg3, Rg5, and Rk1, as effective active components, could be enriched by the improved process of converting ginsenoside Rd by citric acid heat treatment.

NSTX-U research advancing the physics of spherical tokamaks

The objectives of NSTX-U research are to reinforce the advantages of STs while addressing the challenges. To extend confinement physics of low-A, high beta plasmas to lower collisionality levels, understanding of the transport mechanisms that set confinement performance and pedestal profiles is being advanced through gyrokinetic simulations, reduced model development, and comparison to NSTX experiment, as well as improved simulation of RF heating. To develop stable non-inductive scenarios needed for steady-state operation, various performance-limiting modes of instability were studied, including MHD, tearing modes, and energetic particle instabilities. Predictive tools were developed, covering disruptions, runaway electrons, equilibrium reconstruction, and control tools. To develop power and particle handling techniques to optimize plasma exhaust in high performance scenarios, innovative lithium-based solutions are being developed to handle the very high heat flux levels that the increased heating power and compact geometry of NSTX-U will produce, and will be seen in future STs. Predictive capabilities accounting for plasma phenomena, like edge harmonic oscillations, ELMs, and blobs, are being tested and improved. In these ways, NSTX-U researchers are advancing the physics understanding of ST plasmas to maximize the benefit that will be gained from further NSTX-U experiments and to increase confidence in projections to future devices.

Assessing thermal hazards and toxicity of raw biomass particles from prevalent agricultural crops in China

Fire and explosion hazards pose significant safety concerns in the processing and storage of biomass particles, warranting the safe utilization of these particles. This study employed scanning electron microscopy, thermogravimetric analysis, and cone calorimetry to investigate the thermal hazards and toxicity of raw biomass particles from four prevalent agricultural crops in China: rice, sorghum, corn, and reed. Among the samples, corn exhibited the highest heat output of 8006.82 J/g throughout the thermal decomposition process. The quantitative evaluation of critical heat flux, heat release rate intensity, fire growth rate index (FIGRA), post-ignition fire acceleration (PIFA) and flashover potential (X) revealed a substantial fire risk inherent to all the examined straw samples. Notably, corn displayed the lowest FIGRA value of 8.30 kW/m2 s, while rice demonstrated the minimum PIFA value of 16.11 kW/m2 s. Moreover, the X values for all four biomass particle types exceeded 10 under varying external heat flux levels, indicating their high propensity for fire hazards. Analysis of CO and CO2 emissions during combustion showed all four biomass samples exhibited high concentrations throughout, from the initial stages to the end. The present study offers crucial insights for formulating comprehensive fire safety guidelines tailored to the storage and processing of biomass particles.

Study on membrane fouling mechanisms and mitigation strategies in a pilot-scale anaerobic membrane bioreactor (P-AnMBR) treating digestate

Anaerobic Membrane Bioreactor (AnMBR) are employed for solid-liquid separation in wastewater treatment, enhancing process efficiency of digestion systems treating digestate. However, membrane fouling remains a primary challenge. This study operated a pilot-scale AnMBR (P-AnMBR) to treat high-concentration organic digestate, investigating system performance and fouling mechanisms. P-AnMBR operation reduced acid-producing bacteria and increased methane-producing bacteria on the membrane, preventing acid accumulation and ensuring stable operation. The P-AnMBR effectively removed COD and VFA, achieving removal rates of 82.3 % and 92.0 %, respectively. Higher retention of organic nitrogen and lower retention of ammonia nitrogen were observed. The membrane fouling consisted of organic substances (20.3 %), predominantly polysaccharides, and inorganic substances (79.7 %), primarily Mg ions (10.1 %) and Ca ions (4.5 %). To reduce the increased transmembrane pressure (TMP) caused by fouling (a 10.6-fold increase in filtration resistance), backwash frequency experiment was conducted. It revealed a 30-min backwash frequency minimized membrane flux decline, facilitating recovery to higher flux levels. The water produced amounted to 70.3 m³ over 52 days. The research provided theoretical guidance and practical support for engineering applications, offering practical insights for scaling up P-AnMBR.

The restless population of bright X-ray sources of NGC 3621

We report on the multi-year evolution of the population of X-ray sources in the nuclear region of NGC 3621 based on and observations. Among these, two sources, X1 and X5, after their first detection in 2008, seem to have faded below the detectability threshold, a most interesting fact as X1 is associated with the active galactic nucleus (AGN) of the galaxy. Two other sources, X3 and X6, are presented for the first time, the former showing a peculiar short-term variability in the latest available dataset, suggesting an egress from eclipse, and hence belonging to the handful of known eclipsing ultra-luminous X-ray sources. One source, X4, previously known for its heartbeat (i.e. a characteristic modulation in its signal with a period of $ h), shows a steady behaviour in the latest observation. Finally, the brightest X-ray source in NGC 3621, here labelled X2, shows steady levels of flux across all the available datasets, but a change in its spectral shape, reminiscent of the behaviours of Galactic disc-fed X-ray binaries.