Fluorescence Emission Maximum Research Articles

Structure and Spectral Properties of Er3+-Doped Bismuth Telluride Near-Infrared Laser Glasses.

TeO2-Bi2O3-B2O3-ZnO laser glasses doped with Er3+ were synthesized through an optimized melt-quenching method. The absorption spectra at 808 nm LD pumping were studied. Various spectral tests and data analyses indicate that the maximum fluorescence emission intensity can be obtained when the Er3+ doping concentration reaches 2%. In this case, the emission cross-section can reach up to 9.12 × 10-21 cm2 and the gain coefficient at 1.55 μm is 6.17 cm-1. Simultaneously, the sample has a lower phonon energy in the high-frequency band at 1077 cm-1, which reduces the probability of non-radiative relaxation. The calculated energy transfer coefficient CD-A is 13.8 × 10-40 cm6/s, reflecting the high cross-relaxation probability of Er3+ in the sample, which promotes the luminescence of 1.55 μm and favors the emission in the near-infrared region. The comprehensive results demonstrate that the prepared Er3+-doped bismuth telluride laser glass can be used as a promising and high-quality gain material for near-infrared lasers.

Enhancement of non-covalent interaction between soy protein isolate and quercetin by sodium alginate

Effects of sodium alginate (SA) on the non-covalent interaction between soybean protein isolate (SPI) and quercetin (Que) were investigated by multispectral technology, molecular docking and dynamics simulation technology. Structural alterations of the binary complexes were observed after SA addition, characterized by a red shift of maximum fluorescence emission wavelength. The introduction of 0.1% (w/v) SA led to a reduction of 12.3% in the α-helix and β-sheet structures, accompanied by 12.6% increase in the β-turn and random coil conformations. The binding of SA to SPI provided electrostatic interactions and facilitated the subsequent binding of SPI to Que. Molecular docking confirmed that hydrophobic interactions and electrostatic interactions were also the main driving force. Molecular dynamics simulation emphasized that the ternary complexes with SA exhibited greater stability compared to the binary ones. The foaming and emulsifying properties of SPI-Que complexes were enhanced by 33.76% and 68.28%, respectively, due to the addition of SA.

An Asymmetric NIR-II Organic Fluorophore with an Ultra-Large Stokes Shift for Imaging-Guided and Targeted Phototherapy.

NIR-II imaging-guided phototherapy is an attractive, yet challenging, tumor treatment strategy. By monitoring the accumulation of phototherapy reagents at the tumor site through imaging and determining the appropriate therapy window, the therapeutic effect could be significantly improved. Probes with NIR-II (1000-1700 nm) fluorescence emission and a large Stokes shift hold great promise for fluorescence imaging with deep penetration, minimized self-quenching, and high spatiotemporal resolution. However, due to the lack of a suitable molecular framework, the design of a simple small-molecule dye with a large Stokes shift and NIR-II fluorescence emission has rarely been reported. Herein, we prepare an asymmetric D-π-A type NIR-II fluorescence probe (TBy). The probe is incapsulated in an amphiphilic polymer and modified with a fibronectin targeting peptide CREKA, which could recognize the fibrin-fibronectin complex overexpressed in multiple malignant tumors. The nanoparticles thus constructed (TByC-NPs) have maximum fluorescence emission at 1037 nm with a large Stokes shift of 426 nm, which is the largest Stokes shift among organic NIR-II fluorescent dyes reported in the literature. The TByC-NPs exhibit a good NIR-II imaging performance, active tumor targeting, and good photothermal and photodynamic capabilities. In vitro and in vivo studies verify that the TByC nanoplatform shows outstanding biocompatibility for NIR-II imaging-guided phototherapy and provides an excellent antitumor effect.

Rapid, portable and visualizing nitrite detection enabled by a rationally designed meso-aminoindole substituted pyronine-based fluorescent probe

Nitrite (NO2−) widely exists in our daily diet, and its excessive consumption can lead to detrimental effects on the human central nervous system and an elevated risk of cancer. The fluorescence probe method for the determination of nitrite has developed rapidly due to its simplicity, rapidity and sensitivity. Despite establishing various nitrite sensing platforms to ensure the safety of foods and drinking water, the simultaneous achievement of rapid, specific, affordable, visualizing, and on-site nitrite detection remains challenging. Here, we designed a novel fluorescent probe by using Rhodamine 800 as the fluorescent skeleton and 5-aminoindole as the specific reaction group to solve this problem. The probe shows a maximal fluorescence emission at 602 nm, thereby avoiding background emission interference when applied to food samples. Moreover, this unique probe exhibited excellent sensing capabilities for detecting nitrite. These included: a rapid response time within 3 min, a noticeable color change that the naked eye can observe, a low detection limit of 13.8 nM, and a remarkable selectivity and specificity to nitrite. Besides that, the probe can detect nitrite quantitatively in barreled drinking water, ham sausage, and pickles samples, with good recoveries ranging from 89.0 % to 105.8 %. More importantly, based on the probe fixation and signal processing technology, a portable and smart sensing platform was fabricated and made convenient and rapid analysis the content of NO2− in real samples possible. The results obtained in this work provide a new strategy for the design of high-performance nitrite probes and feasible technology for portable, rapid and visual detection of nitrite, and this probe holds the potential as a practical tool for alleviating concern regarding nitrite levels.

Sensitive and rapid detection of ciprofloxacin and ofloxacin in aqueous samples by a facile and green synthesized copper nanocluster as a turn-on fluorescent probe

The present method reports a rapid, inexpensive and sensitive sensing system based on fluorescence turn-on strategy for trace detection of ciprofloxacin (CIP) and ofloxacin (OFL) in aqueous samples. In a one pot method, copper nanocluster whose dimensions are less than 15 nm, were easily prepared and decorated with sodium gluconate (Gl@CuNCs) as a biocompatible material.The Gl@CuNCs were characterized with XRD, TEM, DLS, TG-DTA techniques as well UV–Vis, FT-IR and fluorescence spectroscopies.The maximum fluorescence emission of Gl@CuNCs at 414 nm with excitation at 322 nm shifted to higher wavelength upon addition of CIP and OFL. A good linear relationship between fluorescence emission and drug concentration was achieved in the concentration range of 0.005–0.3 μg mL−1 (15–900 nM for CIP and 14–830 nM for OFL). The limits of detection (LOD) for the determinations of CIP and OFL were calculated to be 9 and 8 nM, respectively. Furthermore, even a 100-fold higher concentration of interfering species had no significant effect on the detection of CIP and OFL. The proposed method was successfully used to determine CIP and OFL in drinking water, cow milk, human urine and serum samples with satisfactory recoveries.

Protein Interaction and Molecular Docking Analysis by Schiff Base Derived from 2,4-Dinitro Phenyl Hydrazine

A novel and cost-effective 2,4-dinitrophenyl hydrazine derived from Schiff base 1-benzylidine-2-(2,4-dinitrophenyl) hydrazine ( L) was designed and characterized using various spectroscopic techniques. The interaction between L and bovine serum albumin (BSA) has been carried out using UV–Vis and fluorescence spectroscopy, DSC, SEM, and molecular docking methods. The phosphate buffer ([Formula: see text]) solution of BSA showed fluorescence emission maxima at 342[Formula: see text]nm. Upon addition of L to the BSA solution, it quenched the fluorescence emission at 342[Formula: see text]nm. The quenching of the fluorescence emission is due to the formation of a complex between L and BSA. The binding constant was calculated from the fluorescence titrations and found to be [Formula: see text][Formula: see text]M[Formula: see text]. Further, molecular docking analysis was carried out to establish the binding between L and BSA.

A novel g-C3N4@La:Y2O3 nanocomposite fluorescence sensor for simultaneous determination and photocatalytic degradation of Ulipristal acetate and Tacrolimus using Doehlert design optimization

Graphitic carbon nitride nanocomposite doped with La:Y2O3 was used as a new sensor for detection and determination of two hazardous active pharmaceutical compounds, Tacrolimus and Ulipristal acetate, by fluorescence spectrophotometry. This novel nanosensor has a fantastic ability to detect these drugs quickly, accurately, and simultaneously. The effect of Tacrolimus on this nanosensor is the quenching of fluorescence emission intensity at the wavelength of 369 nm while the Ulipristal acetate increases the fluorescence emission at 433 nm. Doehlert design was used to optimize the effective factors to reach the maximum fluorescence emission intensity of the nanosensor. Factors including pH, buffer solution concentration and the ratio of La:Y2O3 dopant in the nanocomposite structure. Under optimal conditions, the limit of detection of 17 nM and the limit of qualification of 58 nM for Tacrolimus and the limit of detection of 11 nM and the limit of qualification of 36 nM for Uipristal acetate were obtained with good accuracy. The prepared g-C3N4@La:Y2O3 nanocomposite has a reasonable ability to photodegrade these two drugs. In this regard, the process of photocatalytic degradation of Tacrolimus and Ulipristal acetate was investigated under visible light irradiation. The effect of active species in photocatalytic degradation was evaluated in order to determine the exact degradation mechanism, and the effect of Fenton factors on analytes degradation was also investigated.

Lentils/urea as precursors for profound S and N doping of carbon dots for selective sequential determination of Hg(II) and S(II) in food and environmental samples

In this article, we described a new platform for probing toxic pollutants, namely Hg2+ and S2-, in aquatic environment by tracing the “on–off-on” fluorescence signals of quantum dots. To achieve this, red lentils and urea, as natural precursors, were utilized as sources of S and N doping, respectively, to fabricate blue fluorescent carbon quantum dots, namely, lentils/urea quantum dots (LUQDs) with good quantum yield and plentiful S-doping. In the present work, the quality-by-design (QbD) strategy was applied to control and select the optimum conditions for the microwave-aided synthesis of the carbon dots. LUQDs exhibit excitation-dependent emissions, where the maximum fluorescence emission was at 360 nm after excitation at 300 nm. During the detection step, the fluorescence of LUQDs is quenched by the incorporation of Hg2+ over the range of 0.50–70.0 μM. Next, S2- reacts with Hg2+, resulting in turning on the fluorescence emission of LUQDs in the range of 10.0–150.0 µM.The method was applied for the detection of both Hg2+ and S2- in tap, sewage, and river water samples with a recovery rate ranging between 98.96 % and 101.26 %; in addition, Hg2+ was detected in canned Tuna samples with a recovery of 98.70 %. Furthermore, the greenness of the developed method was confirmed through various greenness metrics.

Fluorescent Molybdenum Disulfide Quantum Dots for Sensitive Detecting Curcumin in Food Samples through FRET Mechanism.

A selective and sensitive fluorometric assay was developed for specific determination of curcumin (Cur) based on fluorescence resonance energy transfer (FRET) between molybdenum disulfide quantum dots (MoS2 QDs) and Cur. The MoS2 QDs were prepared via a one-step hydrothermal protocol using sodium molybdate dihydrate, L-cysteine (Cys) as precursors, and sodium cholate (SC) as a modification agent. The as-prepared MoS2 QDs possessed maximum fluorescence emission at 460nm with a 20% of fluorescence quantum yield (FQY). It was found that the fluorescence of MoS2 QDs could be quantitatively quenched by Cur through FRET mechanism. Therefore, Cur could be detected in the range of 0.1-20µg mL- 1 with a detection limit of 5 ng mL- 1. Additionally, the developed MoS2 QDs based fluorescent assay has been successfully applied for real food sample analysis with satisfactory results.

A Reaction-based Ratiometric Fluorescent Probe with Large STOKES Shift for Cu2+ in Neat Aqueous Solution.

A novel reaction-based ratiometric fluorescent probe 1 for Cu2+ using picolinate as the reaction site and hemicyanine as the fluorophore was developed. 1 displayed maximum absorption peak at 355nm and fluorescence emission peak at 500nm, with large Stokes shift of 145nm. Upon reaction with Cu2+, the maximum absorption and fluorescence emission peaks red-shifted to 390nm and 570nm respectively, owing to Cu2+-induced hydrolysis of the picolinate moiety in 1. Meanwhile, the solution of 1 turned from green to orange under a 365nm UV lamp. 1 not only could detect Cu2+ ratiometrically by the ratios of both absorbance (A390 nm/A355 nm) and fluorescence intensity (F570 nm/F500 nm), but also displayed large Stokes shift, fast response, high sensitivity and excellent selectivity over other metal ions in neat aqueous solution.

Anthracene and Pyrene Derivatives as Blue Fluorophores: Synthesis, Characterization and Photophysical Properties

Ant hracene and pyrene derivatives have been widely studied as emitting materials in optoelectronic devices due to their excellent fluorescence properties. In the present study, two novel blue fluorophores from anthracene and pyrene (PAP and PTATP) were successfully synthesized using a Suzuki-cross coupling reaction and their photophysical properties were elucidated. PTATP with an extended p-conjugation system had a fluorescence emission maximum in green-blue region at 475 nm, whereas PAP, with a shorter conjugation length, emitted pure-blue emission peak at 442 nm. The study of absorption and emission spectra in various solvents found that both compounds produced solvent-independent spectra due to their non-polar molecules. In addition, the aggregation-caused quenching phenomenon was observed, when the emission spectra were recorded in high water fraction solvent.

Incorporation of eggshell waste in the preparation of carbon quantum dot nanoprobes for the determination of COVID-19 antiviral drug; molnupiravir

New carbon quantum dots (CQDs) with multi-doped elements from eggshell biomass waste have been employed as a direct, fast, green, and selective probe for the fluorometric determination of molnupiravir, a COVID-19 antiviral drug. For the first time, the eggshell@CQDs were prepared through a simple, single-step microwave heating process that only took 90 s. Upon excitation at λex 340 nm, the resulting CQDs exhibited a maximum bluish fluorescence emission at λem 408 nm. Molnupiravir was found to quench the native fluorescence of the prepared CQDs in a quantitative manner, based on a static mechanism by forming a non-emissive complex. The spectrofluorometric method designed for molnupiravir detection was validated per the International Council for Harmonization (ICH) requirements. The proposed fluorescent probe showed good linearity for molnupiravir detection over a range of 2.5–70 µg/mL, with percent recoveries ranging from 99.53 % to 101.79 % and %RSD (relative standard deviation) less than 1 %. The eggshell@CQDs were successfully employed to determine molnupiravir levels in marketed hard capsules, yielding good percent recoveries and repeatability. The developed approach was found to be greener than the published HPLC/UV approach, as assessed by the analytical eco-scale, green analytical procedure index (GAPI), and analytical greenness metric approach (AGREE). Furthermore, this approach highlights the potential of synthesizing CQDs from natural biomass, specifically low-value biomass waste such as eggshells.

A pH-regulated fluorescence covalent organic framework for quantitative water content detection in methanol

In this paper, we designed and synthesized a two-dimensional fluorescent covalent organic framework (TAPB-DMTP-COF) for the precise determination of H2O content in methanol. The COF was synthesized using two typical monomers by grinding method, which significantly reduced the synthesis time. By adjusting the pH value of the COF suspension to 4.0, the portion of the COF material structure is disrupted, thereby mitigating π-π stacking and resolving the aggregation-caused quenching (ACQ) effect. Consequently, the non-fluorescent TAPB-DMTP-COF exhibited blue-purple fluorescence emission in methanol. At the same time, it is observed that in the presence of H2O, there is a red shift in the maximum fluorescence emission peak of TAPB-DMTP-COF, which correlates with the H2O content within a specific range. Notably, this redshift demonstrates a linear relationship with H2O content from 4% to 80% in methanol. Our work presents novel insights for efficient analysis and detection of H2O content in methanol and could be used for H2O detection in other organic solvents.

An “on-off-on” fluorescent sensor based on TSPP-gallic acid: Visual detection of S2− in actual samples

A novel “on-off-on” switches fluorescence sensor based on TSPP-gallic acid (GA) for S[Formula: see text]-detecting was designed in this article. 5,10,15,20- (4-sulphonatophenyl) porphyrin (TSPP) was synthesized by a modified “one-pot” method. The synthesized TSPP was used as a fluorescence probe for the construction of a fluorescence sensing system. At room temperature, the maximum fluorescence emission wavelength could be obtained at 642 nm when the excitation wavelength was 515 nm when the fluorescence signal was in the “on” mode. The TSPP solution appeared pink in color at this moment. When GA was introduced into the TSPP solution, the fluorescence signal was turned off (fluorescence intensity was quenched) due to the protonation of TSPP, which was caused by the weak acidity of GA. The color of the TSPP solution changed from pink to green. Following that, an acid-base reaction between S[Formula: see text]and GA was initiated when S[Formula: see text]was introduced into the TSPP-GA system, leading to the liberation of TSPP and restoration of fluorescence intensity. The solution color reverted to red, indicating that the fluorescence sensing system had returned to the “on” mode. The TSPP-GA system had good selectivity and sensitivity to S[Formula: see text], the linear range was 4.52 × 10[Formula: see text] M [Formula: see text] 4.34 × 10[Formula: see text] M, and the detection limit (LOD) was 0.87 [Formula: see text] M. It could be used to detect sulfur ions in actual samples with satisfactory recoveries and RSD values.

CB[8]- and triarylboron-based supramolecular organic framework for microRNA detection, tumor-targeted drug delivery, and photodynamic therapy.

Supramolecular organic frameworks (SOFs) are widely used for biological detection and drug delivery. In this study, a SOF system was fabricated through the self-assembly of photosensitive triarylboron (TAB), TAB-6-methyl, and CB[8]. The maximum fluorescence emission of TAB-6-methyl was greatly enhanced and red-shifted from 560 nm to 610 nm after SOF formation. The SOF can specifically respond to a microRNA by dissembling and then combining with microRNA, which is accompanied by a fluorescence shift from 610 nm to 560 nm, thus providing a ratiometric readout for microRNA detection. The photosensitivity of TAB-6-methyl can be further improved by forming a SOF, which can be used in photodynamic therapy. By constructing another guest molecule, TAB-5-1-cRGD, we successfully embedded cRGD in the SOF system to improve its tumor-targeting ability. Moreover, we used this SOF system as a fluorescence imaging probe for targeted tumor imaging and as a drug carrier system for loading DOX to achieve combined photodynamic and chemotherapy treatment of tumors.

Visible Light Driven CO2 Photoreduction Using TiO2 Nanotube Arrays Embedded with Low Bandgap Carbon Nitride Nanoparticles

The extraordinary thermal and photochemical stability, superior charge transport, and tunable band positions of graphitic carbon nitride (g-CN), which is constituted of elements that are plentiful on Earth, renders g-CN an important semiconductor photocatalyst for heterogeneous catalysis [1,2]. Despite these advantages, carbon nitride-based semiconductors do not function effectively as freestanding photocatalysts or photoelectrodes due to a rapid carrier recombination rate and a slightly wide bandgap that only enables them to capture blue and UV photons [3,4]. Anodically formed TiO2 nanotube arrays (TNTAs) are semiconducting wide bandgap scaffolds with excellent photocatalytic properties due to the intrinsic orthogonalization of charge generation/transport and charge transfer processes. Herein, we use a novel in situ electrophoretic anodization to embed low bandgap carbon nitride nanoparticles (CNNPs) in the walls of titania nanotubes. The likelihood of the CNNPs leaching off the TNTA photoanode during photoelectrochemical processes was eliminated by encapsulating CN inside a TiO2 matrix. CNNPs were formed by the thermal condensation polymerization of carbon nitride utilizing citric acid and urea as the precursors, and exhibited some unusual properties, including a lower bandgap of 2.1 eV, a highly redshifted fluorescence emission maximum at 2.35 eV, surface carboxylate groups, and the emergence of unique structural characteristics corresponding to amorphous yet graphitic carbon [5]. In contrast to bulk g-CN, which has a C:N ratio of 0.75, the CNNPs possessed an elevated C:N ratio as high as 1.87 at the surface. The additional carbon was found to be both amorphous and graphitic, although the structural characteristics of g-CN were mostly unaffected, as validated by diffractometric and spectroscopic data. Even in the absence of a sacrificial agent, the CNNP@TNT nanocomposite demonstrated enhanced performance in sunlight-driven CO2 photoreduction. When compared to the freestanding TNT photocatalyst, the CO yield of photoreduction for the CN@TNT hybrid was more than three times higher. UV-filtered illumination of the CNNP@TNT heterojunction photocatalyst generated appreciable quantities of methane and CO (3.41 and 8.78 μmolg–1h–1 respectively). In situ electrophoretic anodization is an innovative approach to incorporate semiconductor quantum dots into TiO2 nanotubes or other electrochemically grown nanostructures.REFERENCES1. Kessler, F. K. et al., Nature Reviews Materials (2017) 2 (6), 1.2. Chaulagain, N. et al., ACS Applied Materials & Interfaces (2022) 14 (21), pp.24309-24320.3. Kumar, P. et al., Advanced Optical Materials (2020) 8 (4), Art. No. 1901275.4. Fu, J. et al., Advanced Energy Materials (2018) 8 (3), Art. No. 1701503.5. Alam, K.M. et al., Chemical Engineering Journal (2023) 456, Art. No. 141067.

Generalized polarization and time-resolved fluorescence provide evidence for different populations of Laurdan in lipid vesicles

The solvatochromic dye Laurdan is widely used in sensing the lipid packing of both model and biological membranes. The fluorescence emission maximum shifts from about 440 nm (blue channel) in condensed membranes (So) to about 490 nm (green channel) in the liquid-crystalline phase (Lα). Although the fluorescence intensity based generalized polarization (GP) is widely used to characterize lipid membranes, the fluorescence lifetime of Laurdan, in the blue and the green channel, is less used for that purpose. Here we explore the correlation between GP and fluorescence lifetimes by spectroscopic measurements on the So and Lα phases of large unilamellar vesicles of DMPC and DPPC. A positive correlation between GP and the lifetimes is observed in each of the optical channels for the two lipid phases. Microfluorimetric determinations on giant unilamellar vesicles of DPPC and DOPC at room temperature are performed under linearly polarized two-photon excitation to disentangle possible subpopulations of Laurdan at a scale below the optical resolution. Fluorescence intensities, GP and fluorescence lifetimes depend on the angle between the orientation of the linear polarization of the excitation light and the local normal to the membrane of the optical cross-section. This angular variation depends on the lipid phase and the emission channel. GP and fluorescence intensities in the blue and green channel in So and in the blue channel in Lα exhibit a minimum near 90o. Surprisingly, the intensity in the green channel in Lα reaches a maximum near 90o. The fluorescence lifetimes in the two optical channels also reach a pronounced minimum near 90o in So and Lα, apart from the lifetime in the blue channel in Lα where the lifetime is short with minimal angular variation. To our knowledge, these experimental observations are the first to demonstrate the existence of a bent conformation of Laurdan in lipid membranes, as previously suggested by molecular dynamics calculations.

Spectroscopic and thermodynamic characterization of the interaction between sugar-stabilised silver nanoparticles and wheat germ agglutinin (WGA), a chitin binding lectin

Nanomaterials have lately been investigated in agriculture as eco-friendly and effective antifungal agents. Many nanomaterials, notably metal nanoparticles, have strong antifungal properties. Among metal nanoparticles, Ag nanoparticles have received the most attention as antifungal agents. Many plant lectins have been identified as antifungal agents. Conjugating AgNPs with antifungal lectins is thus expected to improve Ag nanoparticle antifungal efficacy. Understanding the molecular interactions and physical features of lectin-sugar-stabilised nanoparticle conjugates is critical for future applications. WGA has traditionally been used as an anti-tumor and antifungal agent. To investigate the prospect of developing an effective biocompatible antifungal system with applications in medicine and agriculture, fluorescence spectroscopy was used to investigate the interaction between sugar-stabilised silver nanoparticles and WGA. During the association, protein intrinsic fluorescence emission is suppressed by about ∼15 % at saturation, with no significant shift in fluorescence emission maxima. Binding tests reveal a strong bond. Stern-Volmer analysis of the quenching data indicates that the interaction happens via a static quenching process that induces complex formation. The study of hemagglutination activity and interaction experiments in the presence of particular sugar shows that the lectin's sugar-binding site is separate from the nanoparticle-binding site, and cell recognition is conserved in the lectin-nanoparticle complex. The Van't Hoff plot thermodynamic parameters suggest that the contact is hydrophobic. The fact that ΔGo is negative shows that the binding is a spontaneous process. CD spectroscopy experiments reveal that the lectin's secondary structure is not affected while binding to the nanoparticle. Our findings suggest that a stable WGA-silver nanoparticle combination may emerge for a variety of applications.

Two distinct mechanisms of flavoprotein spectral tuning revealed by low-temperature and time-dependent spectroscopy.

Flavins such as flavin mononucleotide or flavin adenine dinucleotide are bound by diverse proteins, yet have very similar spectra when in the oxidized state. Recently, we developed new variants of flavin-binding protein CagFbFP exhibiting notable blue (Q148V) or red (I52V A85Q) shifts of fluorescence emission maxima. Here, we use time-resolved and low-temperature spectroscopy to show that whereas the chromophore environment is static in Q148V, an additional protein-flavin hydrogen bond is formed upon photoexcitation in the I52V A85Q variant. Consequently, in Q148V, excitation, emission, and phosphorescence spectra are shifted, whereas in I52V A85Q, excitation and low-temperature phosphorescence spectra are relatively unchanged, while emission spectrum is altered. We also determine the x-ray structures of the two variants to reveal the flavin environment and complement the spectroscopy data. Our findings illustrate two distinct color-tuning mechanisms of flavin-binding proteins and could be helpful for the engineering of new variants with improved optical properties.

Pyrrolizine-3-ones: Synthesis and evaluation of photophysical properties

We describe a synthetic approach for pyrrolizine-3-one derivatives and their photophysical properties. These compounds are prepared by a series of reactions employing the substituted pyrroles in one-pot, two-step oxidation, and intramolecular cyclization processes. The photophysical properties of the synthesized compounds were studied by using UV–Vis and fluorescence spectroscopy in different solvents. Maximum absorbance peaks were observed around 306–416 nm and maximum fluorescence emission around 603–614 nm and 465–498 nm for pyrrolyl and N-methyl pyrrolyl substituents, respectively. The introduction of a pyrrolyl substituent had a significant impact on the Stokes shifts (192–206 nm) and quantum yield values ranged from 0.002 to 0.046.