Flexible Ring Research Articles

Influence of intensity distributions on the process dynamics during laser deep penetration welding of pure nickel with a flexible ring mode laser source

Current research results demonstrate the potential of spatter reduction in laser deep penetration welding by using adapted laser beam intensity distributions between a ring and a core intensity. The spatter-reducing effect, resulting from the additional ring intensity, is often attributed to an enlarged keyhole opening. However, it remains a matter of debate how exactly an additional ring intensity influences the process. This study, therefore, investigates the effect of an increasing ring intensity on process dynamics and the spatter formation regime. Laser beam welding experiments were carried out on 2.4068 nickel hidden T-joints at different welding speeds of up to 16 m/min, as well as different intensity distributions, while maintaining a constant weld depth. The tests were evaluated by using two high-speed cameras from different angles to analyze spatter and their formation mechanisms as well as the keyhole opening. Metallographic analyses and x-ray images were used to determine influences on the seam shape and porosity. It was shown that a change in intensity distribution has a significant influence on the melt flow, the resulting amount of spatter, and the porosity, which is comparable across the investigated welding speeds. While a core-based power distribution leads to spatter formation on the rear of the keyhole opening, it was shown that a ring-based power distribution leads to spatter formation on both sides of the keyhole. With an optimal power distribution, spatter formation could be largely prevented. Based on these findings, the single wave regime, a stabilized regime, and a lateral spatter regime were identified.

Synergistic Effects of Unconventional Hydrogen Bonds and π-Stacking Interaction and Their Excited-State Dependence: The Origin of Unusual Photophysical Properties of Aromatic Thioketones in Acetonitrile and Hydrocarbons.

It has been established experimentally that aromatic thioketones possess several inherently unique photophysical properties, some of which are highly sensitive even to common hydrocarbon solvents. However, the deeper reasons and the underlying mechanisms remain unclear up to date. In this study, the multistate complete active space second-order perturbation theory (MS-CASPT2) has been utilized to investigate the five lowest-lying electronic states (S0, T1, S1, T2, and S2) of 4H-1-benzopyran-4-thione (BPT) in acetonitrile and hydrocarbons. The results show that the S1, T1, and T2 states of BPT are close in energy so that the T2-state-mediated S1 → T2 → T1 and T1 → T2 → S1 transitions could occur in tens of picoseconds, which exhibits little dependence on the formation of the BPT-solvent complexes and on the bulk-solvent effect. This explains why thermally activated delayed fluorescence from the S1 state has been observed for many aromatic thioketones in both inert media and hydrocarbons. Meanwhile, our calculations show that the intracomplex noncovalent interactions could be automatically adjusted by the redistribution of π-electrons in the flexible aromatic rings. This allows the S2 → S1 internal conversion to occur efficiently in the vicinity of the two-state conical intersection, which results in the remarkable changes in the S2-state lifetimes and fluorescence quantum yields of many aromatic thioketones from inert media to hydrocarbon solvents. The aforementioned inherent photophysical properties could be qualitatively understood by a simple model of frontier molecular orbitals. This model could be used to understand photophysical properties of other aromatic compounds (such as aldehydes, ketones, amines, and carboxylic acids) in different solvents.

Ring only repair of bileaflet mitral valve prolapse with mitral regurgitation: Insights from computational modeling

This study evaluates the efficacy of annuloplasty repair as a standalone procedure for treating bileaflet mitral valve prolapse with mitral regurgitation (MR). Various flexible ring bands for MR of different severities were compared to assess their biomechanical impact and treatment outcomes. Computational beating heart models, based on the Living Heart Human Model, were utilized to simulate annuloplasty repairs. Repairs using bands of varying lengths were modeled on moderate and severe MR cases, considering bileaflet mitral valve prolapse. Key parameters, including regurgitant orifice area (ROA), prolapse severity, coaptation length, leaflet position, and deformation, were computed to compare conditions before and after implantation. Annuloplasty repairs effectively reduced the ROA in both moderate and severe MR cases, achieving complete sealing in selective instances. Additionally, annuloplasty repair corrected bileaflet prolapse, with prolapse severity decreasing as the annular size increased. Successful coaptation was indicated by the expansion of each leaflet’s contact area distribution and percentage in contact with the opposing leaflet. The risk of systolic anterior motion, that may obstruct the left ventricular outflow tract, was minimized, as the anterior leaflet was directed towards the posterior position. In conclusion, annuloplasty repair alone can effectively treat MR when an appropriate band length is selected. It facilitates a significant reduction in ROA, correction of bileaflet prolapse, and improvement in leaflet coaptation. These findings have important clinical implications, potentially offering a less complex surgical treatment avenue and reducing complications in the management of MR.

The influence of anomalies in supporting structures on the validation of finite-element blade bearing models

Finite-element analysis is the only means to determine the load distribution of large slewing bearings considering flexible bearing rings and supporting structures. For reliable results, the plausibility of the models need to be validated. Previous attempts on validating a finite-element model of a slewing bearing against measurement results have indicated a huge dependence of the deformation on tolerances in the supporting structures. This dependence has not yet been explored in research in favor of a focus on tolerances of the bearing itself. The present work explores different irregularities of the flange that connects to the outer ring of the bearing and their effects on bearing deformation. The results show that single dents or bulges on the flange and inclined flanges of the adapter ring significantly change the load distribution and contact angles of the bearing. They also aggravate the risk of truncation. For the calculated fatigue life however, the bearings seem to be robust to these uncertainties for the shown load cases. The dimensions of the investigated tolerances are verified by comparing the resulting deformations of the bearing outer ring against experimental data.

Escape of an active ring from an attractive surface: Behaving like a self-propelled Brownian particle.

Escape of active agents from metastable states is of great interest in statistical and biological physics. In this paper, we investigate the escape of a flexible active ring, composed of active Brownian particles, from a flat attractive surface using Brownian dynamics simulations. To systematically explore the effects of activity, persistence time, and the shape of attractive potentials, we calculate escape time τ_{e} and effective temperature T_{eff}. We observe two distinct escape mechanisms: Kramers-like thermal activation at small persistence times, where ln(τ_{e})∼1/(k_{B}T_{eff}), and the maximal force problem at large persistence time, where τ_{e} is determined by persistence time. The escape time explicitly depends on the shape of the potential barrier at high activity and large persistence time. Moreover, when the propulsion force is biased along the ring's contour, escape becomes more difficult and is primarily driven by thermal noise. Our findings highlight that, despite its intricate configuration, the active ring can be effectively modeled as a self-propelled Brownian particle when studying its escape from a smooth surface.

Design and Validation of Single-Axis 3D-Printed Force Sensor Based on Three Nested Flexible Rings.

Force measurement is crucial in numerous engineering applications, while traditional force sensors often face problems such as elevated expenses or significant measurement errors. To tackle this issue, we propose an innovative force sensor employing three nested flexible rings fabricated through 3D additive manufacturing, which detects external forces through the displacement variations of flexible rings. An analytical model on the basis of the minimal energy method is developed to elucidate the force-displacement correlation with nonlinearity. Both FEM simulations and experiments verify the sensor's effectiveness. This sensor has the advantages of low expenses and easy manufacture, indicating promising prospects in a range of applications, including robotics, the automotive industry, and iatrical equipment.

Study on rigid-flexible coupling modeling of planetary gear systems: Incorporation of the pass effect and random excitations

A rigid-flexible coupling model for the planetary gear system is developed, in which the flexibility of the ring gear, input shaft, and carrier are considered. Subsequently, rotational modal projection is proposed to simulate the meshing of the flexible ring gear at any angle of planet gear revolution, and the coordinate transformation equations are presented to establish the coupling between rigid body and rotating flexible body. These two approaches incorporate the pass effect into the coupling model. Additionally, a method employing pre-emphasized noise to simulate random excitations is introduced. The model is validated by comparing computed modal frequencies and dynamic responses with those from ANSYS software and experiment, respectively. Results indicate that the proposed method accurately simulates the modulation signal observed in the experiment. Closely matched resonances excited by random excitations are apparent in experimental and simulated acceleration spectra, highlighting the validity of the proposed method and aiding in the determination of operational system modes. In addition, analyses of parameter influences are conducted, which further reveal the dynamic characteristics of the system.

An Adaptive Reclosing Scheme for Flexible DC Ring Grid Based on Residual Voltage Waveform Offset Detection

An Adaptive Reclosing Scheme for Flexible DC Ring Grid Based on Residual Voltage Waveform Offset Detection

Influence of Tire-Enveloping Model Complexity on High-Frequency Simulations

ABSTRACT Race tires are subject to high speeds and high vertical loads during cornering. They are also subject to extreme stress when they are driven over high-frequency and low-amplitude curbs, often leading to tire failures. Research and development by D. C. Davis and P. W. A. Zegelaar has shown that when the tire moves over high-frequency, low-amplitude, and short-wavelength obstacles, it exhibits obstacle-enveloping properties. Tire response over such obstacles includes vertical force variation, longitudinal force variation, and rotational speed variation. Additionally, such road inputs excite tire belt dynamics that include high-frequency modes. Therefore, a single-contact-point model is no longer sufficient to predict tire response over such obstacles. To better capture the tire obstacle-enveloping behavior, advanced contact patch models such as the tandem-cam model by P. W. A. Zegelaar, the radial–interradial spring model by J. M. Badalmenti and G. R. Davis Jr., and the flexible ring model by S. Gong have been developed. To capture high-frequency tire belt dynamics, the rigid-ring model has been developed by P. W. A. Zegelaar. Previous work combines the rigid-ring model with the tandem-cam model to capture obstacle-enveloping behavior and tire belt dynamics up to 60–100 Hz. This paper presents a comparative study of different tire–road contact models to simulate high-frequency curbs typically found at racetracks. The curb profile of the Singes corner at the Paul Ricard racetrack is chosen for simulations as it is known to be extremely demanding on the tires, often causing failures. An advanced four-wheel model is used to simulate a race car at high speeds. Metrics to quantify the tire response over these high-frequency curbs are created and an investigation is conducted to quantify the influence of tire model complexity on the metrics.

Excluded volume effects on tangentially driven active ring polymers.

The conformational and dynamical properties of active ring polymers are studied by numerical simulations. The two-dimensionally confined polymer is modeled as a closed bead-spring chain, driven by tangential forces, put in contact with a heat bath described by the Brownian multiparticle collision dynamics. Both phantom polymers and chains comprising excluded volume interactions are considered for different bending rigidities. The size and shape are found to be dependent on persistence length, driving force, and bead mutual exclusion. The lack of excluded volume interactions is responsible for a shrinkage of active rings when increasing driving force in the flexible limit, while the presence induces a moderate swelling of chains. The internal dynamics of flexible phantom active rings shows activity-enhanced diffusive behavior at large activity values while, in the case of self-avoiding active chains, it is characterized by active ballistic motion not depending on stiffness. The long-time dynamics of active rings is marked by rotational motion whose period scales as the inverse of the applied tangential force, irrespective of persistence length and beads' self-exclusion.

Adaptive and Dynamic Nonintertwined Assembly of Rigid and Flexible Rings

Adaptive and Dynamic Nonintertwined Assembly of Rigid and Flexible Rings

The use of a convex light appliance and mouldable rings for patients with an ostomy and effluent leakage in the early postoperative period

Background/aims: Patients with digestive ostomies frequently experience effluent leakage in the early postoperative period, leading to complications and reduced quality of life. The convex appliance and adaptable rings in ostomy (CONAN) study investigated a new combined treatment strategy for reducing leakage and improving patient satisfaction. Methods: This prospective, multicenter study involved 244 patients with digestive ostomies and early effluent leakage across 54 stoma units in Spain. Patients were treated with the CONAN strategy, using a light convex ostomy appliance (Easiflex Confort Convex Light) and a flexible ring (Brava moldable). Stoma care nurses collected data on leak episodes per day and patient satisfaction (0–10 scale) at baseline and 2–3 weeks post-discharge. Multivariate analysis identified patient characteristics associated with greater treatment benefit. Results: Patients experienced a significant reduction in mean leak episodes per day (3.4 ± 5.2 to 1.3 ± 2.3, p<.0001). Mean patient satisfaction significantly increased post-treatment (5.1 ± 2 to 7.2 ± 1.7, p<.0001). Multivariate analysis revealed the following factors were associated with high patient satisfaction (≥ 8 over 10): shorter hospital admission, programmed surgery (vs. emergency), closed ostomy appliance (vs. open) and multi-piece appliance systems. Conclusions: The CONAN strategy, combining a light convex ostomy appliance and flexible rings, effectively reduces leakage and improves satisfaction in patients with digestive ostomies and early effluent leakage. Patients with longer hospital stays, emergency ostomy surgery, open ostomy systems and single-piece appliances may benefit most from early intervention with this strategy.

Simultaneous Tricuspid Valve Repair at the Time of Mitral Valve Surgery: Determinants of Postoperative Pacemaker Implantation

Guidelines recommend tricuspid valve (TV) repair for patients with severe tricuspid valve regurgitation (TR) undergoing surgery for degenerative mitral valve (MV) disease, but management of ≤ moderate TR is controversial. This study examines the incidence and causes of bradyarrhythmias leading to PPM implantation. Review of patients undergoing simultaneous TV repair and MV surgery for degenerative MV disease from 2001 to 2022 (N=404). Primary endpoint was the incidence of postoperative PPM implantation. Secondary endpoints included the incidence of high-degree AV block and overall survival. All patients underwent TV repair at the time of MV surgery; 332 (82%) underwent MV repair and 72 (18%) MV replacement. Tricuspid valve repair techniques included flexible band (n=258, 63.8%), DeVega annuloplasty (n=78, 19.3%), complete flexible ring (n=49, 12.1%), and incomplete rigid ring (n=19, 4.7%). The 30-day mortality was 0.5% (n=2). A total of 35 (8.7%) patients had a PPM implanted postoperatively, 26 (6.4%) for high-degree AV block. On multivariable analysis, only older age was associated with PPM implantation. Patients who received a PPM due to high-degree AV block had reduced overall survival (Figure, p=0.01). Need for permanent pacing following TV repair at the time of MV surgery is not uncommon, but there are few modifiable factors that might reduce this risk. Careful selection of patients with less-than-severe TR and surgical techniques may reduce PPM-related risks and complications.

Study on Ring Deformation and Contact Characteristics of Thin-Walled Bearing for RV Reducer

The thin-walled rings of the RV reducer main bearings are prone to structural elastic deformation, which can significantly change the bearing mechanical characteristics. According to the actual assembly state of the RV reducer, the simulation model of the planetary frame–main bearings–pin gear housing is established considering the ring deformation. The model was used to calculate and comparatively analyze the ring deformation and contact characteristics of thin-walled bearings under rigid and flexible conditions, on the basis of which the mechanism of ring deformation was described, and the effects of load conditions, ring thickness and radial clearance on ring deformation, flexible contact characteristics, and ultimate carrying capacity were analyzed. The results show that the distribution of contact loads is the main factor affecting the ring deformation. The ring deformation can optimize the bearing contact characteristics, and the greater the deformation, the more pronounced the optimization effect. However, excessive ring deformation makes the contact ellipse more susceptible to truncation, which, in turn, reduces the ultimate carrying capacity. This study indicates a 38.2% decrease in the carrying capacity of the flexible ring model compared to that of the rigid ring model. In this paper, the effect of ring deformation on bearing mechanical characteristics is deeply discussed. The research results have important guiding significance for the structural optimization design of thin-walled bearings.

Analysis of Kinematics and Dynamics of Rolling Ring Based on Finite Element Method

The working performance of the conductive rolling ring has a crucial impact on the overall energy security and on-orbit life of a satellite. To ensure the real-time transmission of signal and current, it is necessary to control the motion pattern of the rolling ring. In this paper, the finite element analysis method is used to carry out kinematics and dynamics simulation analysis, analyze the motion stability of the rolling ring, and discuss the relationship between the size of the idler gear, the driving torque, and the flexible contact pressure. The research results show that the numerical simulation and theoretical analysis show that the deviation angle is between 0 and 1.52 when the initial installation of the rolling ring is deviated by using the existing camber design of the inner and outer rings. Both have a self-recovery function. The driving torque and the size of the idler gear are nonlinear, and the contact force is proportional to the radius of the idler gear. With the increase in the compression of the radius of the flexible ring, the driving torque and the contact force will increase accordingly. The method of reducing the compression or increasing the size of the idler gear can be used to reduce the driving torque and maintain a certain contact to facilitate the transmission of electrical signals.

Tricuspid repair: short and long-term results of suture annuloplasty techniques and rigid and flexible ring annuloplasty techniques

BackgroundFunctional tricuspid regurgitation may arise from left heart valve diseases or other factors. If not addressed concurrently with primary surgical intervention, it may contribute to increased morbidity and mortality rates during the postoperative period. This study investigates the impact of various repair techniques on crucial factors such as systolic pulmonary artery pressure (SPAP), tricuspid valve regurgitation, and New York Heart Association (NYHA) functional capacity class in the postoperative period.Materials and methodsFrom April 2007 to June 2013, 379 adults underwent open-heart surgery for functional tricuspid regurgitation. Patients were categorized into four groups: Group 1 (156) with De Vega suture annuloplasty, Group 2 (60) with Kay suture annuloplasty, Group 3 (122) with Flexible Duran ring annuloplasty, and Group 4 (41) with Semi-Rigid Carpentier-Edwards ring annuloplasty. Demographic, clinical, operative, and postoperative data were recorded over a mean follow-up of 35.6 ± 19.1 months. Postoperative SPAP values, tricuspid regurgitation grades, and NYHA functional capacity classes were compared among the groups.ResultsNo statistically significant differences were observed among the groups regarding age, gender, preoperative disease diagnoses, history of previous cardiac operations, or echocardiographic characteristics such as preoperative ejection fraction, SPAP, and tricuspid regurgitation. Hospital and intensive care unit length of stay and postoperative complications also showed no significant differences. However, patients in Group 3 exhibited longer Cardio-Pulmonary Bypass duration, cross-clamp duration, and higher positive inotrope requirements. While the mortality rate within the first 30 days was higher in Group 1 compared to the other groups (p: 0.011), overall mortality rates did not significantly differ among the groups. Significant regression in functional tricuspid regurgitation and a notable decrease in SPAP values were observed in patients from Group 3 and Group 4 (p: 0.001). Additionally, patients in Group 3 and Group 4 showed a more significant reduction in NYHA functional capacity classification during the postoperative period (p: 0.001).ConclusionAmong the repair techniques, ring annuloplasty demonstrated superiority in reducing SPAP, regressing tricuspid regurgitation, and improving NYHA functional capacity in functional tricuspid regurgitation repairs.

Entire Mitral Valve Reconstruction Using Porcine Extracellular Matrix: Adding a Ring Annuloplasty

PurposeThis study investigated the implications of inserting a flexible annuloplasty ring after reconstructing the entire mitral valve in a porcine model using a previously investigated tube graft design made of 2-ply small intestinal submucosa extracellular matrix (CorMatrix®).MethodsAn acute model with eight 80-kg pigs, each acting as its own control, was used. The entire mitral valve was reconstructed with a 2-ply small intestinal submucosa extracellular matrix tube graft (CorMatrix®). Subsequently, a Simulus® flexible ring was inserted. The characterization was based on mitral annular geometry and valvular dynamics with sonomicrometry and echocardiography.ResultsAfter adding the ring annuloplasty, the in-plane annular dynamics were more constant throughout the cardiac cycle compared to the reconstruction alone. However, the commissure–commissure distance was statistically significantly decreased [35.0 ± 3.4 mm vs. 27.4 ± 1.9 mm, P < 0.001, diff = − 7.6 mm, 95% CI, − 9.8 to (−5.4) mm] after ring insertion, changing the physiological annular D-shape into a circular shape which created folds at the coaptation zone resulting in a central regurgitant jet on color Doppler.ConclusionWe successfully reconstructed the entire mitral valve using 2-ply small intestinal submucosal extracellular matrix (CorMatrix®) combined with a flexible annuloplasty. The annuloplasty reduced the unphysiological systolic widening previously found with this reconstructive technique. However, the Simulus flex ring changed the physiological annular D-shape into a circular shape and hindered a correct unfolding of the leaflets. Thus, we do not recommend a flexible ring in conjunction with this reconstructive technique; further investigations are needed to discover a more suitable remodelling annuloplasty.

Design of compact integrated diamond nitrogen–vacancy center quantum probe

An integrated quantum probe for magnetic field imaging is proposed, where the nitrogen–vacancy (NV) center fixed at the fiber tip is located on the periphery of flexible ring resonator. Using flexible polyimide (PI) as the substrate medium, we design a circular microstrip antenna, which can achieve a bandwidth of 140 MHz at Zeeman splitting frequency of 2.87 GHz, specifically suitable for NV center experiments. Subsequently, this antenna is seamlessly fixed at a three-dimensional-printed cylindrical support, allowing the optical fiber tip to extend out of a dedicated aperture. To mitigate errors originating from processing, precise tuning within a narrow range can be achieved by adjusting the conformal amplitude. Finally, we image the microwave magnetic field around the integrated probe with high resolution, and determine the suitable area for placing the fiber tip (SAP).

Rational Design of Benzobisheterocycle Metallo-β-Lactamase Inhibitors: A Tricyclic Scaffold Enhances Potency against Target Enzymes.

Antimicrobial resistance is a global public health threat. Metallo-β-lactamases (MBLs) inactivate β-lactam antibiotics, including carbapenems, are disseminating among Gram-negative bacteria, and lack clinically useful inhibitors. The evolving bisthiazolidine (BTZ) scaffold inhibits all three MBL subclasses (B1-B3). We report design, synthesis, and evaluation of BTZ analogues. Structure-activity relationships identified the BTZ thiol as essential, while carboxylate is replaceable, with its removal enhancing potency by facilitating hydrophobic interactions within the MBL active site. While the introduction of a flexible aromatic ring is neutral or detrimental for inhibition, a rigid (fused) ring generated nM benzobisheterocycle (BBH) inhibitors that potentiated carbapenems against MBL-producing strains. Crystallography of BBH:MBL complexes identified hydrophobic interactions as the basis of potency toward B1 MBLs. These data underscore BTZs as versatile, potent broad-spectrum MBL inhibitors (with activity extending to enzymes refractory to other inhibitors) and provide a rational approach to further improve the tricyclic BBH scaffold.

Microstructure and mechanical properties of Flexible Ring Mode laser welded 304 stainless steel

Flexible Ring Mode (FRM) laser welding is a relatively new composite laser welding technology. The present study focused on the FRM laser welded joints produced from 4.5 mm-thick 304 stainless steel. The effects of various laser modes on the macroscopic morphology, microstructure, microhardness, and tensile properties of the produced welded joints were systematically investigated. The results showed that, when the ring laser power was set at 1000 W and the center laser power at 3000 W, a maximum weld area of 6.23 mm2 was obtained. Employing a composite laser with a center laser power greater than the ring laser power resulted in the fewest number of welding spatter particles on both sides of the weld bead, indicating an effective inhibition of welding spatter by the ring laser. Conversely, using a composite laser with a center laser power equal to the ring laser power still led to the presence of small welding spatter particles, indicating differences in the laser combination modes in suppressing welding spatter for the welding of 304 stainless steel. Increased cooling and a large presence of small turbulence contributed to the grain refinement in the fusion zone of the welded joints produced using a composite laser with a central laser power greater than the ring laser power. Consequently, this welded joint exhibited the highest maximum tensile strength among all tensile test specimens reaching 95.2 % of the base metal’s maximum tensile strength. However, the fractured surfaces of the tensile test specimens produced using a composite laser with a center laser power equal to the ring laser power exhibited the highest number density and largest size of oxide particles, resulting in a joint elongation of only 77.3 % of the base metal’s elongation. This study emphasizes the potential application of this FRM laser and provides theoretical guidance for selecting the optimal laser combination mode for FRM laser welding of stainless steel.