Finite Element Analysis Study Research Articles

Influence of endodontic access cavity design on mechanical properties of a first mandibular premolar tooth: a finite element analysis study

ObjectivesThis study aimed to investigate the influence of access cavity designs on the mechanical properties of a single-rooted mandibular first premolar tooth under various static loads using a finite element analysis.Materials and methods3-dimensional FEA designs were modeled according to the access cavity designs: an intact tooth (control), traditional access cavity (TEC-I), traditional access cavity with Class-II mesio-occlusal cavity design (TEC-II), conservative access cavity (CEC), ninja access cavity (NEC), caries-driven access cavity (Cd-EC), buccal access cavity (BEC) and bucco-occlusal access cavity (BOEC). After the simulated access cavity preparations, root canal treatment was simulated and three different static loads which mimicked oblique and vertical mastication forces were applied to the models. The stress distribution and maximum Von Misses stress values were recorded. The maximum stress values were obtained on both enamel and dentin under multi-point vertical loads.ResultsThe maximum stress values were obtained on both enamel and dentin under multi-point vertical loads. Under all load types, the minimum stress distribution was observed in the control group, followed by CEC, NEC and BEC designs. The highest stress concentration was detected in Cd-EC and TEC-II designs. Under single-point vertical loading, the stress was mostly concentrated in the lingual PCD area, while under multi-point vertical loading, the entire root surface was stress-loaded except for the lingual apical third of the root.ConclusionPreserving tooth tissue by simulating CEC, NEC and BEC access cavities increased the load capacity of a single-rooted mandibular first premolar following simulated endodontic treatment.

Comparison of the use of biocompatible materials and titanium in the treatment of midshaft clavicle fractures with a patient-specific plate: a finite element analysis study.

Clavicular midshaft fractures treated with titanium plates may encounter complications like implant failure. We assess if alternative biocompatible materials suchs as PLA, PLA/HA, PEEK offer comparable stability. Our study evaluates the biomechanical performance of these materials in surgical management of midshaft clavicle fractures. We simulated a personalized fixation implant with four different materials and conducted finite element analysis in ANSYS to assess maximum von Mises stress (MvMs). The MvMs occurring on the plates, screws, clavicle, and fracture site were recorded. MvMs on titanium material at the 6th hole level (764.79MPa) and the 6th screw level (503.38MPa), with the highest stresses observed at 48.52MPa on the lateral clavicle at the 1st hole level and 182.27MPa on the medial clavicle at the 6th hole level. In PLA material analyses, the highest MvMs were observed at the 3rd hole level (340.6MPa) and the 3rd screw level (157.83MPa), with peak stresses at 379.63MPa on the lateral clavicle fracture line and 505.44MPa on the medial clavicle fracture line. In PLA/HA material analyses, the highest MvMs were at the 3rd hole (295.99MPa) and 3rd screw (128.27MPa), with peak stresses at 220.33MPa on the lateral clavicle and 229.63MPa on the medial clavicle fracture line. In PEEK material analyses, the highest MvMs were at the 3rd hole (234.74MPa) and 6th screw (114.48MPa), with peak stresses at 184.36MPa on the lateral clavicle and 180.1MPa on the medial clavicle. Our findings indicate that titanium material shows significantly higher stresses on plates and screws compared to those on the clavicle, suggesting a risk of implant failure. PLA and PLA/HA were inadequate for fixation. Although stress on the plate with PEEK material is higher than on the clavicle, it remains lower than titanium, indicating potential stability at fracture site. Further research is needed to confirm these findings.

Finite element analysis and biomechanical study of "sandwich" fixation in the treatment of elderly proximal humerus fractures.

Proximal humerus fractures (PHFs) are common in the elderly and usually involve defects in the medial column.The current standard for medial column reconstruction is a lateral locking plate (LLP) in combination with either an intramedullary fibula support or an autogenous fibula graft. However, autogenous fibula graft can lead to additional trauma for patients and allogeneic fibular graft can increase patients' economic burden and pose risks of infection and disease transmission. The primary objective of this study was to introduce and assess a novel "Sandwich" fixation technique and compare its biomechanical properties to the traditional fixation methods for PHFs. In this study, we established finite element models of two different internal fixation methods: LLP-intramedullary reconstruction plate with bone cement (LLP-IRPBC) and LLP-intramedullary fibula segment (LLP-IFS). The biomechanical properties of the two fixation methods were evaluated by applying axial, adduction, abduction, torsional loads and screw extraction tests to the models. These FEA results were subsequently validated through a series of biomechanical experiments. Under various loading conditions such as axial, adduction, abduction, and rotation, the LLP-IRPBC group consistently demonstrated higher structural stiffness and less displacement compared to the LLP-IFS group, regardless of whether the bone was in a normal (Nor) or osteoporotic (Ost) state. Under axial, abduction and torsional loads, the maximum stress on LLPs of LLP-IRPBC group was lower than that of LLP-IFS group, while under adduction load, the maximum stress on LLPs of LLP-IRPBC group was higher than that of LLP-IFS group under Ost condition, and almost the same under Nor condition. The screw-pulling force in the LLP-IRPBC group was 1.85 times greater than that of the LLP-IFS group in Nor conditions and 1.36 times greater in Ost conditions. Importantly, the results of the biomechanical experiments closely mirrored those obtained through FEA, confirming the accuracy and reliability of FEA. The novel "Sandwich" fixation technique appears to offer stable medial support and rotational stability while significantly enhancing the strength of the fixation screws. This innovative approach represents a promising strategy for clinical treatment of PHFs.

Bending behaviour of surface corroded and perforated corroded steel tubes repaired by laser cladding additive manufacturing

In recent years, laser cladding (LC) technology has been increasingly applied and investigated for repairing damaged surface on metal structural components. However, there are limited experimental studies on the bending behaviour of the LC repaired steel components. And an effective repair method for the perforated corroded steel components is still lacking, therefore, this paper introduces a novel LC repair method for such steel tube. Four-point bending tests were conducted on four specimens, including one intact steel tube (IT), one surface corroded steel tube (SCT), one surface corroded steel tube repaired by LC (SRT), and one perforated corroded steel tube repaired by LC (PRT) to verify the effectiveness of the LC repair methods by evaluating their structural performance in terms of bending capacity, rotational stiffness, and ductility. The experimental results showed that the bending strength and rotational stiffness of the SRT and PRT can be fully restored and even slightly higher than those of the IT. The strain analysis indicated that the LC repair method can significantly reduce stress/strain concentration caused by surface corrosion and perforation corrosion. The experiments were replicated numerically by means of finite element (FE) analysis and parametric studies were performed to investigate the effect of different factors on the bending behaviour of the PRT and SRT. Furthermore, design formula for predicting the elastic bending capacity of the LC repaired steel tube was developed.

A Finite Element Analysis Study of Influence of Femoral Stem Material in Stress Shielding in a Model of Uncemented Total Hip Arthroplasty: Ti-6Al-4V versus Carbon Fibre-Reinforced PEEK Composite

Total hip arthroplasty is one of the most common and successful orthopaedic operations. Occasionally, periprosthetic osteolysis associated with stress shielding occurs, resulting in a reduction of bone density where the femur is not properly loaded and the formation of denser bone where stresses are confined. To enhance proximal load transfer and reduce stress shielding, approaches, including decreasing the stiffness of femoral stems, such as carbon fibre-reinforced polymer composites (CFRPCs), have been explored through novel modular prostheses. The purpose of the present study was to analyse, by the finite element analysis (FEA) method, the effect that the variation of material for the distal part of the femoral stem has on stress transmission between a modulable prosthesis and the adjacent bone. Methods: Through three-dimensional modelling and the use of commercially available FEA software Ansys R2023, the mechanical behaviour of the distal part of the femoral stem made of CFRPC or Ti-6Al-4V was obtained. A load was applied to the head of the femoral stem that simulates a complete walking cycle. Results: The results showed that the use of a material with mechanical characteristics close to the bone, like CFRPC, allowed for optimisation of the transmitted loads, promoting a better distribution of stress from the proximal to the distal part of the femur. This observation was also found in some clinical studies in literature, which reported not only an improved load transfer with the use of CFRPC but also a higher cell attachment than Ti-6Al-4V. Conclusions: The use of a material that has mechanical properties that are close to bone promotes load transfer from the proximal to the distal area. In particular, the use of CFRPC allows the material to be designed based on the patient’s actual bone characteristics. This provides a customised design with a lower risk of prosthesis loss due to stress shielding.

Finite element analysis study: Topology optimization for the front lower arm with innovative double and complex phase materials

Suspension systems used in vehicles are an important factor affecting comfort, safety, and vehicle performance. These systems are effective in the vehicle's total weight and fuel consumption. However, while lightening the weight, it should also be ensured that the strength is within safe limits. For this purpose, dual-phase (DP) and complex-phase (CP) steel materials were used. In the study, the topology optimization of the front lower suspension arm, designed for a light commercial vehicle, was carried out with the finite element method. As a result of the topology optimization, the weight was reduced by 7.5% compared to the current design, while maintaining the safe strength values. This result will significantly contribute to reducing material costs by using dual-phase (DP) and complex-phase (CP) steel materials, reducing exhaust emissions by lightening vehicle weight, and developing more sustainable designs.

Quantifying the effects of five rehabilitation training methods on the ability of elderly men to control bowel movements: a finite element analysis study.

The study aims to develop a finite element model of the pelvic floor and thighs of elderly men to quantitatively assess the impact of different pelvic floor muscle trainings and the urinary and defecation control ability. A finite element model of the pelvic floor and thighs of elderly men was constructed based on MRI and CT. Material properties of pelvic floor tissues were assigned through literature review, and the relative changes in waistline, retrovesical angle (RVA) and anorectad angulation (ARA) to quantitatively verify the effectiveness of the model. By changing the material properties of muscles, the study analyzed the muscle strengthening or impairment effects of the five types of rehabilitation training for four types of urination and defecation dysfunction. The changes in four outcome indicators, including the retrovesical angle, anorectad angulation, stress, and strain, were compared. This study indicates that ARA and RVA approached their normal ranges as material properties changed, indicating an enhancement in the urinary and defecation control ability, particularly through targeted exercises for the levator ani muscle, external anal sphincter, and pelvic floor muscles. This study also emphasizes the effectiveness of personalized rehabilitation programs including biofeedback, exercise training, electrical stimulation, magnetic stimulation, and vibration training and advocates for providing optimized rehabilitation training methods for elderly patients. Based on the results of computational biomechanics, this study provides foundational scientific insights and practical recommendations for rehabilitation training of the elderly's urinary and defecation control ability, thereby improving their quality of life. In addition, this study also provides new perspectives and potential applications of finite element analysis in elderly men, particularly in evaluating and designing targeted rehabilitation training.

Acute Periprosthetic Hip Fractures With Short, Uncemented Femoral Stems

BackgroundUncemented femoral stems in hip arthroplasty have shown excellent long-term results, and several systematic studies indicate satisfactory performance of short stems. However, biomechanical and finite element analysis studies have suggested that shorter stems allow greater micromotion, producing greater strain at the implant-bone interface, which potentially increases the risk for periprosthetic fracture (PPF). We sought to assess this risk within our unit. MethodsOur institution’s arthroplasty database was searched for all primary total hip arthroplasties using short femoral stems performed between July 14, 2009 and August 29, 2022. The overall PPF rate and the PPF rate for individual femoral stems were established. Preoperative X-rays for each case were analyzed to characterize individual proximal femoral geometry. A data analysis was performed to identify risk factors for PPF. ResultsFor the time period assessed, 3,192 short femoral stems were implanted. This included 1,561 of stem A and 1,631 of stem B. Women constituted 55.37% of the cohort. The average patient age was 66 years (range, 22 to 95). The PPF rate was 0.6%, with 19 PPFs identified at a follow-up of 3 months. There was a significantly higher fracture rate in stem A (0.96%) compared to stem B (0.25%) (P ≤ .01). Proximal femoral geometry, age, and sex were not determined to be risk factors for PPF in our cohort. Individual surgeons and surgical approaches appeared to confer no increased risk. There was no significant difference in average stem length, but multivariate analysis identified stem type and stem length as an independent risk factor for PPF. ConclusionsOur study identified individual stem and stem length as independent risk factors for PPF within our cohort. PPF is a multifactorial issue, and consensus on emerging risk factors such as implant design will hopefully inform decisions that can provide further risk reduction for individual patients.

Optimized Clavicle Hook Plate Geometry for Average Korean Clavicle–Acromion Dimensions: A Finite Element Analysis Study

Optimized Clavicle Hook Plate Geometry for Average Korean Clavicle–Acromion Dimensions: A Finite Element Analysis Study

Optimizing functionally graded tibial components for total knee replacements: a finite element analysis and multi-objective optimization study

The optimal design of complex engineering systems requires tracing precise mathematical modeling of the system’s behavior as a function of a set of design variables to achieve the desired design. Despite the success of current tibial components of knee implants, the limited lifespan remains the main concern of these complex systems. The mismatch between the properties of engineered biomaterials and those of biological materials leads to inadequate bonding with bone and the stress-shielding effect. Exploiting a functionally graded material for the stem of the tibial component of knee implants is attractive because the properties can be designed to vary in a certain pattern, meeting the desired requirements at different regions of the knee joint system. Therefore, in this study, a Ti6Al4V/Hydroxyapatite functionally graded stem with a laminated structure underwent simulation-based multi-objective design optimization for a tibial component of the knee implant. Employing finite element analysis and response surface methodology, three material design variables (stem’s central diameter, gradient factor, and number of layers) were optimized for seven objective functions related to stress-shielding and micro-motion (including Maximum stress on the cancellous bone, maximum and mean stresses on predefined paths, the standard deviation of mean stress on paths, maximum and mean micro-motions at the bone-implant interface and the standard deviation of mean micro-motion). Then, the optimized functionally graded stem with 6 layers, a central diameter of 5.59 mm, and a gradient factor of 1.31, was compared with a Ti6Al4V stem for various responses. In stress analysis, the optimal stem demonstrated a 1.92% improvement in cancellous bone stress while it had no considerable influence on the maximum, mean, and standard deviation of stresses on paths. In micro-motion analysis, the maximum, mean, and standard deviation of mean micro-motion at the interface were enhanced by 24.31%, 39.53%, and 19.77%, respectively.

Development of a heavy vehicle torque rod applying continuous fiber reinforced thermoplastic composite materials instead of forged steel material: Design, analysis and optimization

The torque rod is an important component of the suspension system that connects the axle to the chassis in heavy commercial vehicles. The main motivation of this study is the development of a torque rod made of (1) plus cross-section, (2) continuous carbon and glass fiber reinforced hybrid thermoplastic composites, which can replace a forged steel torque rod used in heavy vehicles, has superior mechanical properties, provides minimum cost and weight. This study aims to develop a torque rod before its production within the framework of integration with Computer Aided Design (CAD), Finite Element Analysis (FEA), and Multi-Criteria Decision Making (MCDM). In this study, the design data and the properties of the composite materials were chosen as control factors. The minimum displacement, the best mechanical properties such as tensile stress, compressive stress, torsional shear stress, maximum critical buckling load, and the minimum part weight minimum production cost per piece were selected as quality characteristics. As a result of the FEA study, considering the experimental set of the Taguchi Method L25 orthogonal array, the data on mechanical properties, weight, and production cost per piece were subjected to the MCDM process using the Entropy Weighted TOPSIS method. As a result of the MCDM study, a torque rod made of continuous fiber-reinforced thermoplastic composite material, instead of a torque rod produced by forged steel, had the highest mechanical properties produced, the weight of the torque rod can be reduced by 64.76%, and the production costs per piece can be reduced by 37.5%. This study’s findings have shown that the torque rod produced from continuous fiber-reinforced thermoplastic composite materials in a new geometry with a plus cross-section can be substituted for the torque rod produced by steel forging. Thus, it will contribute to reducing the fixed vehicle weight, especially in heavy commercial vehicles, reducing CO2 emissions, and increasing the range of the vehicles.

Finite Element Analysis of New Modified Three-dimensional Strut Miniplate versus Conventional Plating in Mandibular Symphysis and Angle Fractures - An In vitro Study.

Mandibular fractures are common injuries during maxillofacial trauma, and currently, open reduction and internal fixation are considered gold-standard treatments. There is a wide discussion about which plates give the best outcomes. Hence, we are conducting a biomechanical comparison of two plates for mandibular symphysis and angle fracture with finite element analysis (FEA). The aim of this study was to do a comparative study of FEA between the conventional and our new modified three-dimensional (3D) strut miniplate in mandibular fractures at symphysis and angle regions. Finite element models of symphyseal and angle fractures of the mandible were developed. Each fracture model was then realigned and fixed by the conventional method 2.0 mm system, and our modified 3D strut plating method 2.0 mm system followed by the analysis of various stresses developed in plates and mandibular fracture area after application of load was observed in the study. The modified 3D strut plating system with 2.0 mm miniplates is significantly better in preventing displacement of fracture segments by better distribution of forces compared to the conventional plating system. Rest of the parameters were within the permitted limits. Modified 3D strut plating method was reasonably effective and superior in managing force-displacement compared to the conventional method of fixation for comminuted and unfavourable mandibular symphyseal fracture and angle fracture.

The finite element analysis study of the impact of single and double lag screw fixation on ankle fractures of different sizes

In clinical practice, the choice of single vs. double screw fixation for posterior malleolus fractures (PMF) is theoretically unclear, particularly concerning the size-stability relationship. This study, employing Finite Element Analysis (FEA), assesses biomechanical stability in PMF of varying sizes under both fixation methods. Utilizing a 3D model based on CT scans, we simulated fractures with 10–50% fragment sizes and applied a 600 N force to mimic the single-leg stance. Our evaluation focused on screw Von Mises stress (VMS) and fracture relative displacement (RD). Results show that stability increases with fragment size for both fixation types. Single screw fixation is comparable to double screw in fragments up to 25%, but in larger fragments, double screw significantly enhances stability. This suggests that for fragments over 25%, double screw fixation is preferable, marking a critical threshold for PMF stability.

Additive Manufacturing of Composite Polymers: Thermomechanical FEA and Experimental Study.

This study presents a comprehensive approach for simulating the additive manufacturing process of semi-crystalline composite polymers using Fused Deposition Modeling (FDM). By combining thermomechanical Finite Element Analysis (FEA) with experimental validation, our main objective is to comprehend and model the complex behaviors of 50 wt.% carbon fiber-reinforced Polyphenylene Sulfide (CF PPS) during FDM printing. The simulations of the FDM process encompass various theoretical aspects, including heat transfer, orthotropic thermal properties, thermal dissipation mechanisms, polymer crystallization, anisotropic viscoelasticity, and material shrinkage. We utilize Abaqus user subroutines such as UMATHT for thermal orthotropic constitutive behavior, UEPACTIVATIONVOL for progressive activation of elements, and ORIENT for material orientation. Mechanical behavior is characterized using a Maxwell model for viscoelastic materials, incorporating a dual non-isothermal crystallization kinetics model within the UMAT subroutine. Our approach is validated by comparing nodal temperature distributions obtained from both the Abaqus built-in AM Modeler and our user subroutines, showing close agreement and demonstrating the effectiveness of our simulation methods. Experimental verification further confirms the accuracy of our simulation techniques. The mechanical analysis investigates residual stresses and distortions, with particular emphasis on the critical transverse in-plane stress component. This study offers valuable insights into accurately simulating thermomechanical behaviors in additive manufacturing of composite polymers.

410 Improving Patient Outcomes through Design of Biodegradable Implants for Long Bone Fractures

OBJECTIVES/GOALS: Current long bone fracture standard of care uses inert metal intramedullary nails (IMN), 10x stiffer than femur cortex. Consequent “stress-shielding” bone loss sees >5% of patients needing revision surgery. To improve nonunion healing, we develop automated design optimization methods for biodegradable Mg alloy IMNs to control local reloading. METHODS/STUDY POPULATION: Finite element analysis (FEA) is performed on 3D bone-IMN representations to establish this study’s baseline strain states for existing inert IMN geometries within QCT-informed femoral models under simulated biomechanical loading. FEA with Mg alloy properties for same IMN designs simulate transient IMN material loss through discrete time-step models with experimental in vivo Mg corrosion rates and strain-based bone density evolution using remodeling algorithms from literature. Transient stability and strength metrics, fracture zone stress profiles under gradual reloading and manufacturing constraints are formulated through gradient-based sensitivity analysis into a topology optimization framework (TOF) incorporating a reaction-diffusion degradation model to generate IMN topologies. RESULTS/ANTICIPATED RESULTS: TOF designs for Mg alloy IMNs with transient allowable strength constraints, using safety factors to prevent IMN failure, demonstrate higher compliance than standard inert IMNs with mechanical properties closer to native cortical bone. The biodegradation model within the TOF, informed by corrosion behavior from bone-IMN FEA study, predicts how potential design evolutions affect transient strain states of the system. Thus, local fracture region stress states are controlled by the algorithm optimizing for desirable transient stiffness profiles based on a minimum variance objective of fracture zone stress compared to a target bone stress profile. Optimized IMNs with porous, high surface area features achieve 50% decrease in IMN stiffness over 6 months recovery time and complete in vivo degradation in 24 months. DISCUSSION/SIGNIFICANCE: Our TOF reduces “stress-shielding” effects via design for controlled IMN biodegradation to gradually increase fracture zone loading, stimulating remodeling and reducing current risk of post-operative fracture and surgical removal in ~15k cases/yr. in the U.S. In vitro mechanical and in vivo clinical testing is required to validate design results.

Stress distribution on teeth restored with veneers using various incisal preparation designs: A 3D finite element analysis study

Statement of problemThe type of veneer preparation is often chosen according to the patient’s tooth structure and occlusion. Taking biomechanics into account in this decision-making process provides the clinician with more technical information on how to improve the clinical longevity of restorations. However, biomechanical analyses of veneer preparation designs are sparse. PurposeThe purpose of this 3-dimensional (3D) finite element analysis with microcomputed tomography (µCT) data obtained from realistic models was to assess the influence of different preparations for ceramic and composite resin veneers on restoration and resin layer stress distribution. Material and methodsFour replicas of a central incisor were printed and prepared for laminate veneers with 4 different incisal edge designs: shoulder (SH), palatal chamfer (PC), palatal chamfer and oblique fracture involving the distal angle (OF-PC), and palatal chamfer involving horizontal incisal fracture (IF-PC). After fabrication and cementation of the veneers, the restored replicas were assessed with µCT, and 3D finite element models were built. A 100-N load was applied on the palatal surface at 60 and 125 degrees relative to the longitudinal axis. Maximum principal stress and stress distribution on the veneers, cement layer, and tooth structure were calculated and analyzed. ResultsThe SH preparation exhibited better stress distribution than the PC preparation, and the cement layer and the veneer were subjected to lower stress. The IF-PC preparation had better stress distribution than the OF-PC. The shoulder and IF-PC showed higher stress on laminate veneers, but lower stress on the cement layer. Ceramic veneers exhibited lower stress than composite resin veneers. ConclusionsThe different incisal preparations for laminate veneers influenced stress distribution on restorations and on the resin cement layer. The shoulder type preparation showed better stress distribution and the composite resin veneers showed unfavorable results compared with the ceramic veneers.

A Finite Element Analysis Study of Edentulous Model with Complete Denture to Simulate Masticatory Movement.

The purposes of this study are to establish and validate a finite element (FE) model using finite element analysis methods and to identify optimal loading conditions to simulate masticatory movement. A three-dimensional FE model of the maxillary and mandibular cortical bone, cancellous bone, and gingiva was constructed based on edentulous cone-beam-computed tomography data. Dental computer-aided design software was used to design the denture base and artificial teeth to produce a complete denture. Mesh convergence was performed to derive the optimal mesh size, and validation was conducted through comparison with mechanical test results. The mandible was rotated step-by-step to induce movements similar to actual mastication. Results showed that there was less than a 6% difference between the mechanical test and the alveolar bone-complete denture. It opened 10° as set in the first stage, confirming that the mouth closed 7° in the second stage. Occlusal contact occurred between the upper and lower artificial teeth as the mouth closed the remaining angle of 3° in the third stage while activating the masseter muscle. These results indicate that the FE model and masticatory loading conditions developed in this study can be applied to analyze biomechanical effects according to the wearing of dentures with various design elements applied.

Sagittal support rather than medial cortical support matters in geriatric intertrochanteric fracture: A finite element analysis study

Hip fracture, increasing exponentially with age, is osteoporosis's most severe clinical consequence. Intertrochanteric fracture, one of the main types of hip fracture, is associated with higher mortality and morbidity. The current research hotspots lay in improving the treatment effect and optimizing the secondary stability after intertrochanteric fracture surgery. Cortex buttress reduction is a widely accepted method for treating intertrochanteric fracture by allowing the head-neck fragment to slide and rigidly contact the femoral shaft's cortex. Medial cortical support is considered a more effective option in treating young patients. However, osteo-degenerations features, including bone weakness and cortical thickness thinning, affect the performance of cortex support in geriatric intertrochanteric fracture treatment. Literature focusing on the age-specific difference in cortex performance in the fractured hip is scarce. We hypothesized that this osteo-19 degenerative feature affects the performance of cortex support in treating intertrochanteric fractures between the young and the elderly. We established twenty models for the old and the young with intertrochanteric fractures and performed static and dynamic simulations under one-legged stance and walking cycle conditions. The von Mises stress and displacement on the femur, proximal femoral nail anti-rotation (PFNA) implant, fracture plane, and the cutting volume of cancellous bone of the femur were compared. It was observed that defects in the anterior and posterior cortical bone walls significantly increase the stress on the PFNA implant, the displacement of the fracture surface, and cause a greater volume of cancellous bone to be resected. We concluded that ensuring the integrity and alignment of the anterior and posterior cortical bones is essential for elderly patients, and sagittal support is recommended. This finding suggests that the treatment method for intertrochanteric fracture may differ, considering the patient's age difference.

Investigation of local soil resistance on suction caissons at capacity in undrained clay under combined loading

Winkler modelling offers a flexible and computationally efficient framework for estimating suction caisson capacity. However, there is a limited understanding of the local soil resistance acting on caissons at capacity under combined six degrees-of-freedom (6DoF) loading, which is essential for accurately estimating caisson failure envelopes. Furthermore, existing simplified design models for caissons cannot assess capacity under non-planar lateral and moment loading, which is common in offshore wind applications. To address these limitations, this paper presents a comprehensive three-dimensional (3D) finite element analysis (FEA) study, which investigates the local soil resistance acting on the caisson at capacity in undrained clay under combined 6DoF loading. The paper introduces the concept of ‘soil reaction failure envelopes’ to characterise the interactions between soil reactions at capacity. Closed-form formulations are derived to approximate these soil reaction failure envelopes. An elastoplastic Winkler model is then developed, incorporating linear elastic perfectly plastic soil reactions based on these formulations. The results demonstrate that the Winkler model can provide efficient and reasonably accurate estimations of caisson capacity under combined 6DoF loading, even for irregular soil profiles that pose much uncertainty and challenges to existing macro-element models.

Biomechanical evaluation of four different framework designs of cantilever zirconia resin bonded fixed dental prosthesis: A three-dimensional finite element analysis study

: To measure stress and strain concentrations on four different RBFDP designs and its effect on cement layer and the Periodontal tissues using FEA.: Using CBCT data, two 3D models of a maxilla with missing lateral Incisor were printed. Tooth preparation for RBFDP was done. One model had proximal-groove of 4mm and other had 3mm proximal-groove. Four designs of cantilever RBFDPs were designed. Model-1: #21 abutment/ 3x3mm connector; Model-2: #21 abutment/ 3x4mm connector; Model-3: #23 abutment/ 3x3mm connector and; Model-4: #23 abutment/ 3x4mm connector. All Models were converted into FEA models, occlusal force of 200N was loaded at 450 to long axis of pontic and FEA was carried out. Maximum Principal Strain(MPS) in the RBFDP framework, periodontal tissues and Maximum Shear Stress(MSS) in cement layer were measured to evaluate the impact on periodontal tissues and the risk for framework-debonding respectively.: The MPS of framework in decreasing order was: Model-1>Model-2>Model-3>Model-4. The MPS of PDL: Model-1 and Model-2 > Model-3 and Model-4. MSS in cement layer: Model-1 and Model-2 > Model-3 and Model-4. Adhesion area with shear stress >11MPa: Model-1 and Model-2 > Model-3 and Model-4. MPS and MMS values were lower in models with 3×4mm connector than models with 3x3mm connector.: Adequate Connector dimension and adhesion-area are critical for success of RBFDP. Within the limitations of this study, RBFDP design with 3x4mm connector and Maxillary Canine as abutment for replacing Maxillary Lateral Incisor is better option in terms of framework-debonding risk and preservation of periodontal tissues.