Fine Analysis Research Articles

Moment Redistribution in UHPC Continuous Beams Reinforced with High-Strength Steel Bars: Numerical Investigation and Prediction Model

Considering moment redistribution in the design of ultra-high-performance concrete (UHPC) statically indeterminate structures can fully exploit the load-bearing potential of members, simplify reinforcement details, and save construction costs. Due to the excellent properties of ultra-high-performance concrete (UHPC) that distinguish it from conventional concrete, new characteristics of the moment redistribution manifest in UHPC structures. In this study, a finite element (FE) analytical model was developed to simulate and analyze the bending behavior and moment redistribution of UHPC continuous beams reinforced with high-strength steel bars. The simulation and test results exhibited excellent agreement with the experimental research. Based on the FE model, a fine analysis for nine simulated two-span UHPC continuous beams was conducted with a detailed discussion of the failure modes, load-displacement curves, variations of support reaction forces, tensile strains of steel bars, and the whole process of moment redistribution. Subsequently, the variation rules of moment redistribution in UHPC continuous beams were explored by an extensive parametric study of 108 simulated beams. The studied parameters included a neutral axis depth factor, concrete strength, yielding strength of reinforcement, beam depth, span–depth ratio, reinforcement ratio between the mid-span and intermediate support section, as well as load forms. According to the numerical results, new formulas for estimating the two-stage moment redistribution in UHPC continuous beams with high-strength reinforcement were established. Finally, a comparison of moment redistribution between normal concrete continuous beams and UHPC continuous beams was performed. It can be observed that the elastic moment distribution in UHPC continuous beams was comparatively smaller, while the plastic moment distribution was relatively larger than those of normal concrete continuous beams. Overall, the degree of the total moment distribution in UHPC structures was greater than that of normal concrete structures due to the high ductility of UHPC. The research in this study may provide a technical reference for the practical engineering of UHPC.

Research on Classroom Teaching Practice of General Education Course of "Fine Analysis + Strong Thinking" Driven by Cases Based on OBE Concept

This paper discusses the reform and practice of general education teaching based on OBE concept. According to needs of general education curriculum and society for personnel training, it puts forward a teaching mode with "fine analysis + strong thinking" as the direction and case-driven as the main body, from the aspects of teaching content, teaching design and teaching mode selection, assessment and implementation effect. By comparing the traditional teaching method with the reformed teaching method, it shows that the reformed teaching method can stimulate students' interest in learning and improve their learning effect and comprehensive quality.

Study on the influence of non‐load effects during the whole process of construction of setback super‐tall structures

SummaryThe mechanical characteristics of the setback super‐tall structure are complex, and the design is difficult. In the actual analysis and design process, the relevant influencing factors should be fully considered. In this paper, the fine construction simulation analysis of the super‐tall structure is carried out. Based on the shrinkage test of concrete members, the CEB‐FIP 90 shrinkage model is modified in terms of the parameters of cross‐section shape and size. The modified model is used to calculate the shrinkage strain of concrete, and the influence of uneven settlement of foundation and seasonal temperature on the structure is considered in the construction simulation analysis. The influence proportion of each non‐load effect on the horizontal displacement, vertical displacement, and internal force of key components is obtained. The refined construction analysis results are compared with the field monitoring data, and the data are in good agreement.

Association between diabetes mellitus and cause of death in patients with tuberculosis: A Korean nationwide cohort study

Despite its significant impact on mortality, tuberculosis (TB)-diabetes mellitus (DM) co-prevalence has not been well-elucidated for the cause of death. We investigated the impact of DM on TB-related and non-TB-related deaths in patients with TB. This retrospective nationwide cohort study included patients diagnosed with TB between 2011 and 2017 in South Korea. We performed Fine and Gray regression model analyses to assess the mortality risk of DM classified by cause of death. Of 239,848 patients, 62,435 (26.0%) had DM, and 20,203 died during anti-TB treatment. Of all deaths, 47.9% (9,668) were caused by TB, and the remaining 52.1% (10,535) was attributed to various non-TB-related causes. The mortality rate was higher in the DM than in the non-DM groups in both men and women. DM was associated with a higher risk of TB-related (adjusted hazard ratio [aHR] 1.07, 95% confidence interval [CI] 1.01–1.13) and non-TB-related (aHR 1.21, 95% CI 1.15–1.27) deaths in men; however, only a higher risk of non-TB-related deaths (aHR 1.29, 95% CI 1.20–1.38) in women. Our findings indicate that DM is independently associated with a greater risk of death during anti-TB treatment among patients with TB for both TB-related and non-TB-related deaths.

Fine mapping and analysis of candidate genes for qBT2 and qBT7.2 locus controlling bolting time in radish (Raphanus sativus L.).

Two major QTLs for bolting time in radish were mapped to chromosome 02 and 07 in a 0.37 Mb and 0. 52 Mb interval, RsFLC1 and RsFLC2is the critical genes. Radish (Raphanus sativus L.) is an important vegetable crop of Cruciferae. The premature bolting and flowering reduces the yield and quality of the fleshy root of radish. However, the molecular mechanism underlying bolting and flowering in radish remains unknown. In YZH (early bolting) × XHT (late bolting) F2 population, a high-density genetic linkage map was constructed with genetic distance of 2497.74 cM and an average interval of 2.31 cM. A total of nine QTLs for bolting time and two QTLs for flowering time were detected. Three QTLs associated with bolting time in radish were identified by QTL-seq using radish GDE (early bolting) × GDL (late bolting) F2 population. Fine mapping narrowed down qBT2 and qBT7.2 to an 0.37 Mb and 0.52 Mb region on chromosome 02 and 07, respectively. RNA-seq and qRT-PCR analysis showed that RsFLC1 and RsFLC2 were the candidate gene for qBT7.2 and qBT2 locus, respectively. Subcellular localization exhibited that RsFLC1 and RsFLC2 were mainly expressed in the nucleus. A 1856-bp insertion in the first intron of RsFLC1 was responsible for bolting time. Overexpression of RsFLC2 in Arabidopsis was significantly delayed flowering. These findings will provide new insights into the exploring the molecular mechanism of late bolting and promote the marker-assisted selection for breeding late-bolting varieties in radish.

Legal Analysis of Fines for The Companies That Failing to Provide Wages under Government Act No. 36 of 2021

This study investigates the legal framework surrounding unpaid wages and the subsequent efforts of workers to secure their rightful compensation. Companies employ various tactics to avoid fulfilling their wage obligations, such as delaying payments and making unilateral deductions. In response to these practices, workers, as victims of wage non-payment, persist in seeking their due rights even after fulfilling their job responsibilities. One avenue pursued by workers is engaging in mediation with government intermediaries. The study focuses on the legal context shaped by the government to address the issue, particularly through the enactment of Government Act Number 36 of 2021 on Wages. This legislation plays a crucial role in outlining the government's responsibilities and measures to curb non-payment of wages by companies. Government Regulation No. 36 of 2021 on Wages elucidates the government's role in imposing sanctions, including fines, on companies failing to fulfill their wage obligations to workers. The research aims to shed light on the effectiveness and implications of these legal measures in safeguarding the rights of workers and ensuring fair compensation for their labor.

Mortality patterns of patients with tonsillar squamous cell carcinoma: a population-based study.

Tonsillar squamous cell carcinoma (TSCC) and second primary malignancies (SPMs) are the most common causes of mortality in patients with primary TSCC. However, the competing data on TSCC-specific death (TSD) or SPM-related death in patients with TSCC have not been evaluated. This study aimed to analyze the mortality patterns and formulate prediction models of mortality risk caused by TSCC and SPMs. Data on patients with a first diagnosis of TSCC were extracted as the training cohort from the 18 registries comprising the Surveillance, Epidemiology, and End Results (SEER) database. A competing risk approach of cumulation incidence function was used to estimate cumulative incidence curves. Fine and gray proportional sub-distributed hazard model analyses were performed to investigate the risk factors of TSD and SPMs. A nomogram was developed to predict the 5- and 10-year risk probabilities of death caused by TSCC and SPMs. Moreover, data from the 22 registries of the SEER database were also extracted to validate the nomograms. In the training cohort, we identified 14,530 patients with primary TSCC, with TSCC (46.84%) as the leading cause of death, followed by SPMs (26.86%) among all causes of death. In the proportion of SPMs, the lungs and bronchus (22.64%) were the most common sites for SPM-related deaths, followed by the larynx (9.99%), esophagus (8.46%), and Non-Melanoma skin (6.82%). Multivariate competing risk model showed that age, ethnicity, marital status, primary site, summary stage, radiotherapy, and surgery were independently associated with mortality caused by TSCC and SPMs. Such risk factors were selected to formulate prognostic nomograms. The nomograms showed preferable discrimination and calibration in both the training and validation cohorts. Patients with primary TSCC have a high mortality risk of SPMs, and the competing risk nomogram has an ideal performance for predicting TSD and SPMs-related mortality. Routine follow-up care for TSCC survivors should be expanded to monitor SPMs.

Anti-occupation defect dipole and gradient interface induced excellent giant permittivity in Sr0.95Bi0.05TiO3 ceramics

In this research, non-stoichiometric Bi doped SrTiO3 (ST) ceramics with nominal chemical formula of BixSr1-xTiO3 (x = 0, 0.01, 0.03, 0.05, 0.07) were produced through a conventional solid-state reaction route. A giant permittivity (ε) ∼30000 and low dielectric loss (tanδ) ∼0.03 were obtained in Bi0.05Sr0.95TiO3 ceramic. The temperature-ε and frequency-ε plots were conducted to investigate dielectric properties of the ceramics. The results of dielectric property plots revealed that the Bi0.05Sr0.95TiO3 ceramic has excellent dielectric stability within the range of 103–106 Hz and 30–250 °C. The fine scan XRD analysis, X-ray photoelectron spectrometer (XPS) and first principles calculation results showed that giant permittivity property of the Bi0.05Sr0.95TiO3 ceramic maybe attributed to the Bi‘Ti−VO∙∙−Bi‘Ti defect dipoles caused by Bi anti-occupation doping. And the gradient interface formed by Bi excessive doping also contributed to the giant permittivity. This study offers a new approach for achieving a giant permittivity with low dielectric loss in ST ceramic capacitors.

Accumulation of Ag(0) Single Atoms at Water/Mineral Interfaces during Sunlight-Induced Reduction of Ionic Ag by Phenolic DOM.

Silver (Ag) undergoes a complex and dynamic Ag+/Ag0 cycle under environmental conditions. The Ag+ → Ag nanoparticles (AgNPs) transformation due to the combined actions of sunlight, O2, and dissolved organic matter has been a well-known environmental phenomenon. In this study, we indicate that this process may be accompanied by a pronounced accumulation of Ag(0) single atoms (Ag-SAs) on the minerals' surfaces. According to spherical aberration-corrected scanning transmission electron microscopy and high-energy-resolution X-ray adsorption fine structure analyses, humic acid (HA) and phenol (PhOH) can induce Ag-SAs accumulation, whereas oxalic acid causes only AgNPs deposition. Ag-SAs account for more than 20 wt % of total Ag(0) on the γ-Al2O3 surfaces during HA- and PhOH-mediated photolysis processes. HA also causes Ag-SAs to accumulate on two other prevalent soil minerals, SiO2 and Fe2O3, and the fractions of Ag-SAs are about 15 wt %. Our mechanism studies suggest that a phenolic molecule acts as a reducing agent of Ag+ and a stabilizer of Ag-SAs, protecting Ag-SAs against autocatalytic nucleation.

Incidence and Risk Factors of Veno-Occlusive Disease Are Different in Younger Versus Older Adults Undergoing Allogeneic Hematopoietic Stem Cell Transplantation

Background: Veno-occlusive disease (VOD) is a rare but potentially life-threatening complication following allogeneic stem cell transplantation (allo-SCT). Improved transplant techniques and increased awareness of modifiable risk factors have reduced VOD incidence. However, the interaction of historic risk factors in the current era, particularly with the increasing use of calicheamicin-based therapies and post-transplant cyclophosphamide as GVHD prophylaxis, remains unclear. Methods: We conducted a retrospective, single center, chart-based study of consecutive adult patients (age ≥ 18 years) undergoing allo-SCT at MD Anderson Cancer Center between January 1 st, 2017 and December 31 st, 2021. VOD cases were defined using the classic VOD EBMT criteria or if patients received defibrotide treatment for VOD based on clinical judgment of the treating physician. Risk factors for VOD were evaluated in univariate analysis using Fine and Grey regression analysis. Multivariate analysis was performed using Classification and Regression Tree (CART) analysis to validate the findings of univariate analysis and evaluate independent effects accounting for potential interaction effects. Results: A total of 1561 patients were included in our analysis. Median age was 56 years and 60% were male. Patients primarily had acute myeloid leukemia/myelodysplastic syndrome (AML/MDS; 60%), acute lymphoblastic leukemia (ALL; 13%), or myeloproliferative neoplasms (13%). Most patients had matched related (28%) or unrelated donors (48%), and 21% underwent haploidentical transplantation. Forty-nine (3%) patients received inotuzumab ozogamicin (InO) containing regimens prior to allo-SCT, and 30 (2%) were exposed to gemtuzumab ozogamicin (GO). Post-transplant cyclophosphamide (PTCy) was used as GVHD prophylaxis in 72% of patients. Incidence of VOD in the entire study population was 4.8%. There was a significant difference in the median age of patients diagnosed with VOD compared to those without VOD (46 years vs 56 years, respectively, p=0.001). Further examination of the incidence of VOD within different age groups identified a VOD rate of 16.8% (20/119) in those aged ≤ 25 years compared to 3.8% (55/1442) in those > 25 years (Table 1). Multivariate classification and regression tree (CART) analysis confirmed age as the primary independent determinant of the rate of VOD (Figure 1). Given these findings, risk factor analysis was stratified according to age. In patients ≤25 years of age, disease risk index (DRI) (31% with high/very high DRI vs 12% low/intermediate DRI; p=0.03) and prior lines of chemotherapy (24% with >1 vs 6% with ≤1, p=0.03) were the strongest predictors of VOD. Within the younger cohort of patients with AML/MDS, 2 of 3 patients (67%) who received gemtuzumab ozogamicin (GO) developed VOD compared to 10% who did not receive GO (p=0.05). In patients aged >25 years, elevated baseline bilirubin, AST, ALT, and GO exposure were associated with increased VOD rates. VOD incidence based on baseline bilirubin levels (WNL, >ULN to 1.5x ULN, and >1.5x ULN) was 3%, 14%, and 16%, respectively (p<0.001). For baseline ALT levels (WNL, >ULN to 2.5x ULN, and >2.5x ULN), VOD rates were 4%, 3%, and 8%, respectively (p=0.02). Similarly, VOD rates with baseline AST levels (WNL, >ULN to 2.5x ULN, and >2.5x ULN) were 3%, 4%, and 27%, respectively (p≤0.001). In patients aged >25 years with AML/MDS, those receiving GO had a higher incidence of VOD compared to AML/MDS patients not exposed to GO (15% vs. 3%; p=0.01). There was no significant difference in VOD rates between those receiving PTCy and those receiving alternate GVHD prophylaxis in either age cohort. Conclusion: In summary, our data highlight that young adults (age 18 - 25 years) represent a distinct adult population with increased rates of VOD compared to their older counterparts, which are exacerbated by disease and treatment related factors (DRI and number lines of therapy). In contrast, patients > 25 years of age had low rates of VOD even in the presence of historical predictors, with only hepatic risk factors identified as increasing baseline VOD risk. There was no observed increased incidence of VOD among those receiving PTCy as GVHD prophylaxis.

Fine Detection and Analysis of Hidden Karst in Wellsite with Quasi-Three-Dimensional TDEM Based on Lateral Constraint

Considering that karst caves, underground rivers, and dissolution fractures in shallow carbonate formation in the Sichuan Basin are extremely developed, leakage, failure and plugging difficulties are easy to occur in the drilling process. The TDEM was used to carry out the exploration of hidden karst geological bodies in well QM2, and the quasi-three-dimensional inversion based on lateral constrain was used to invert the TDEM data. Three NW trending anomalous bands were identified in the lower Triassic Jialingjiang Formation within the range of drilling, consisting of seven relatively low-resistivity anomalous zones. Under the guidance of TDEM quasi-three-dimensional inversion resistivity data, the low-resistivity karst development area is avoided, and the specific drilling location of well QM2 is determined. No karst cave and underground river were drilled in the later drilling process of well QM2, as well as no instability phenomenon occurred. It indicates that the TDEM detection results are consistent with the actual drilling, and the quasi-three-dimensional TDEM inversion interpretation data based on lateral constraints is reliable and can accurately detect the buried karst in the wellsite.

SURG-32. EFFICACY OF LASER INTERSTITIAL THERMAL THERAPY (LITT) FOR BIOPSY-PROVEN RADIATION NECROSIS IN RADIOGRAPHICALLY RECURRENT BRAIN METASTASES

Abstract BACKGROUND Evidence is growing for the efficacy of laser interstitial thermal therapy (LITT) for radiation necrosis (RN) following stereotactic radiosurgery (SRS) for patients with brain metastases. Questions remain regarding local control, symptom control, and concurrent use of therapies. METHODS Demographics, intraprocedural data, safety, Karnofsky performance status (KPS) and survival data were prospectively collected from the LAANTERN multi-center registry (NCT02392078) then analyzed on patients consented between 2016-2020 and who were undergoing LITT for biopsy-proven RN at one of 14 U.S. centers. Data was monitored for accuracy. Statistical analysis included individual variable summaries, multivariable Fine and Gray analysis, and Kaplan Meier estimated survival. RESULTS Ninety patients met inclusion criteria. Median hospitalization time was 32.5hrs. Median time to corticosteroid cessation after LITT was 13 days (range 0 - 1229) and cumulative incidence of lesional progression was 19% at 1-year. Median post-procedure overall-survival was 2.6 years [1.7, NR] and 77% at one year as estimated by Kaplan Meier. Median KPS remained 80 through 2-year follow-up. Seizure prevalence improved from 34.4% pre-procedure to 12% 1-month post-LITT and 7.9% at 3-months. There was no significant difference in risk of radiographic progression in total and near-total ablations (91% or greater ablative coverage) versus sub-total ablations (< 90%). Lesion size was not a significant predictor of future radiographic progression. CONCLUSIONS LITT is an effective, minimally invasive, safe treatment for RN, in terms of both local control and symptom management. LITT is effective in the management of lesion-related seizures in addition to averting expected neurological death. LITT facilitates ongoing systemic therapy (particularly immunotherapy) by enabling the rapid cessation of corticosteroids. Effective management options for RN could facilitate the more aggressive use of combined systemic and radiotherapeutic treatment options for brain metastases patients in order to avoid failure due to tumor recurrence and extend survival.

The internal structure of spring mounds of Nefzaoua oasis in Tunisia: Formation of an original geomorphic structure

AbstractSpring mounds are specific geomorphological landforms in arid or semi‐arid environments associated with playas and artesian springs. Spring mounds are found worldwide, especially in the great Artesian Basin of Australia and in North American and Egyptian deserts. They result from an exceptional succession of climatic, geomorphological and hydrogeological conditions, with processes that follow each other in a specific order. In Tunisia, in the arid zone, ca. 126 spring mounds have been identified in Nefzaoua province alone, especially in the oasis east of Chott el Jerid. They have a conical shape that ranges from 200 to more than 2000 m in diameter and 3–30 m tall, and their centre is hollowed out by an artesian spring of fresh water. Palm groves (Phoenix dactylifera) spread out at the foot of each mound. The springs have dried up because of the proliferation of borehole wells. Because of the low electric conductivity (EC) of the sediments (<1 mS cm−1) at their base, spring mounds have been excavated and used as a soil amendment to expand new palm plantations. This excavation allows for analysis of their internal structure, which has never been observed well. In the present study, fine analysis of sediment layers in four sections of two representative mounds showed that vegetation had trapped sediment at their base. Fine strata of variable texture alternating with variable calcium carbonate, gypsum or organic carbon contents suggest a clear limnic origin. Many redoximorphic features, sometimes associated with the presence of old roots, suggest variation in the water level in the centre of the mound. The mounds are capped by a thick layer of indurated gypsum, which helps them resist hydric and aeolian erosion. The origin of the sediment components is discussed.

Anomalous Dissipation and Lack of Selection in the Obukhov–Corrsin Theory of Scalar Turbulence

The Obukhov–Corrsin theory of scalar turbulence [21, 54] advances quantitative predictions on passive-scalar advection in a turbulent regime and can be regarded as the analogue for passive scalars of Kolmogorov’s K41 theory of fully developed turbulence [47]. The scaling analysis of Obukhov and Corrsin from 1949 to 1951 identifies a critical regularity threshold for the advection-diffusion equation and predicts anomalous dissipation in the limit of vanishing diffusivity in the supercritical regime. In this paper we provide a fully rigorous mathematical validation of this prediction by constructing a velocity field and an initial datum such that the unique bounded solution of the advection-diffusion equation is bounded uniformly-in-diffusivity within any fixed supercritical Obukhov-Corrsin regularity regime while also exhibiting anomalous dissipation. Our approach relies on a fine quantitative analysis of the interaction between the spatial scale of the solution and the scale of the Brownian motion which represents diffusion in a stochastic Lagrangian setting. This provides a direct Lagrangian approach to anomalous dissipation which is fundamental in order to get detailed insight on the behavior of the solution. Exploiting further this approach, we also show that for a velocity field in Cα\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$C^\\alpha $$\\end{document} of space and time (for an arbitrary 0≤α<1\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$0 \\le \\alpha < 1$$\\end{document}) neither vanishing diffusivity nor regularization by convolution provide a selection criterion for bounded solutions of the advection equation. This is motivated by the fundamental open problem of the selection of solutions of the Euler equations as vanishing-viscosity limit of solutions of the Navier-Stokes equations and provides a complete negative answer in the case of passive advection.

Wetting and interfacial reactions in liquid Au-Ti alloys / ZrO2 system

This study investigates wetting of zirconia by Au-Ti alloys containing 0.6 to 4 wt% Ti in view of brazing zirconia to titanium with pure gold for biomedical applications. Experiments were carried out using sessile and dispensed drop methods under high vacuum at 1040-1250 °C. Bulk drops and Au-Ti / ZrO2 interfaces were characterized by SEM and FEG-SEM with EDXS analysis. While Au does not wet zirconia, the contact angle θ being ∼ 120°, the addition of Ti in Au leads to a significant improvement of wetting due to the formation of a wettable oxide layer at Au-Ti / ZrO2 interface. The nature of this oxide was determined by X-ray diffraction of the reaction layer after the detachment of the droplet from the substrate or after the dissolution of the droplet. The mechanism of formation and growth of the oxide layer and its growth kinetics were determined based on fine analysis of the Au-Ti / oxide layer / ZrO2 interfacial system.

High-Precision DOA Estimation Based on Synthetic Aperture and Sparse Reconstruction.

The direction-of-arrival (DOA) estimation is predominantly influenced by the antenna's aperture size. However, space constraints on flight platforms often necessitate the use of antennas with smaller apertures and fewer array elements. This inevitably imposes limitations on the DOA estimation's resolution and degrees of freedom. To address these precision constraints, we introduce an accurate DOA estimation method based on spatial synthetic aperture model. This method adopts a two-stage strategy to ensure both efficiency and precision in DOA estimation. Initially, the orthogonal matching pursuit (OMP) reconstruction algorithm processes the original aperture data, providing a rough estimate of target angles that guides the aircraft's flight direction. Subsequently, the early estimations merge with the aircraft's motion space samples, forming equivalent spatially synthesized array samples. The refined angle estimation then employs the OMP-RELAX algorithm. Moreover, with the off-grid issue in mind, we devise an estimation method integrating Bayesian parameter estimation with dictionary sequence refinement. The proposed technique harnesses the spatial synthetic aperture for pinpoint estimation, effectively addressing the challenges of atomic orthogonality and angular off-grid on estimation accuracy. Importantly, the efficiency of deploying sparse reconstruction for angle estimation is bolstered by our phased strategy, eliminating the necessity for fine grid analysis across the entire observation scene. Moreover, the poor estimation accuracy caused by coherent source targets and angular-flickering targets is improved by sparse reconstruction. Through simulation and experiment, we affirm the proposed method's efficacy in angle estimation. The results indicate that target angle estimation errors are limited to within 1°. Furthermore, we assess the impact of variables such as target state, heading angle, spatial sampling points, and target distance on the estimation accuracy of our method, showcasing its resilience and adaptability.

Flow cytometry methods for targeted isolation of ctenophore cells

Cell suspension fluidics, such as flow cytometry (FCS) and fluorescence-activated cell sorting (FACS), facilitates the identification and precise separation of individual cells based on phenotype. Since its introduction, flow cytometry has been used to analyze cell types and cellular processes in diverse non-vertebrate taxa, including cnidarians, molluscs, and arthropods. Ctenophores, which diverged very early from the metazoan stem lineage, have emerged as an informative clade for the study of metazoan cell type evolution. We present standardized methodologies for flow cytometry-mediated identification and analyses of cells from the model ctenophore Mnemiopsis leidyi that can also be applied to isolate targeted cell populations. Here we focus on the identification and isolation of ctenophore phagocytes. Implementing flow cytometry methods in ctenophores allows for fine scale analyses of fundamental cellular processes conserved broadly across animals, as well as potentially revealing novel cellular phenotypes and behaviors restricted to the ctenophore lineage.

Design and Development of Wind Power Refined Simulation Software

A challenge to the steady operation of the system as well as the design, operation, and maintenance of wind power is posed by the wind power industry's rapid development and the rate at which wind power is incorporated into the power system. This work creates high-quality simulation software for wind power to address the complicated modeling requirements brought on by significant wind power penetration. The software implements the functions of fine modeling, offline simulation, real-time simulation, and data analysis and uses Python, Shell, and C++ language programming as its primary programming languages. Additionally, to confirm the software's functionality, this study employs OpenFAST single-unit and three-unit wind field samples. The reality demonstrates how easily real-time simulation software can be implemented and how well it does so. Software also has a cheap time and economic cost, and its application value is considerable.

Terahertz Attenuated Total Reflection Spectral Response and Signal Enhancement via Plasmonic Enhanced Sensor for Eye Drop Detection.

With chronic ocular diseases such as glaucoma and dry eye syndrome, patients have to apply eye drops over the long term. The therapeutic effects of eye drops depend on the amount of drug contained and the stability of the solution. In addition, contamination during usage and transport can also negatively affect the quality and efficacy of eye drops. The current techniques for the characterization of eye drops are often complicated and time-consuming. Developing a fast and non-invasive way of accurately measuring eye drop quality remains an ongoing challenge. The biggest challenge and primary prerequisite for the application of this new detection technique for eye drops is the obtention of a sufficient spectral response and resolvable signal, considering the large background signal contributed by water. In this work, we use terahertz (THz) attenuated total reflection (ATR) spectroscopy combined with a sensitive hybrid graphene oxide (GO) and carbon nanotube (CNT) thin-film sensors to obtain distinct THz spectral signals in commercial eye drops. Various commercial eye drop products have been tested, and we show that they can be differentiated via their spectral signals. Our results provide a solid foundation for the future fine analysis of eye drops and the detection of their quality. Furthermore, THz spectroscopy combined with GO/CNT films has significant potential and advantages for the non-destructive characterization of aqueous pharmaceutical products.

Facile synthesis Cu2O nanomaterials via hydrothermal method: Effect of precursors ratio on structural and morphological characteristics

The single phase Cu2O nanomaterials had been fabricated via facile hydrothermal method using non-toxic precursors of CuSO4.5H2O and Na2SO3 (then, the CuSO4 0.3M and Na2SO3 0.3M solution are mixed with volume ratios of 1:5, 1:6, 1:7 and 1:10, respectively). The observed materials were characterized using fine analysis methods such as X-ray diffraction, scanning electron microscopy, UV-Vis diffuse reflectance spectroscopy, and UV-Vis spectroscopy. The fabricated Cu2O samples had flower-like morphology which was assembled from octahedral. The samples had an average crystalline size of ~20.1-23.3 nm and a narrow bandgap of ~1.98 eV. The photocatalytic activity of samples was investigated via Congo red (CR) dye photodecomposition experiment, the catalyst dose and the concentration of CR values were studied as the factors affecting the photocatalytic efficiency. The results showed that the fabricated Cu2O samples had good photocatalytic ability in decomposing the CR solution in the visible region. The Cu2O (M­1-6) sample had the best degradation efficiency of the CR solution was the (reached 91.3% after 300 min under visible light radiation of the 150W Led lamp at the CR concentration of 20 ppm). The photo-decomposition rate constant of M­1-6 sample reached 0.00774 min-1.