Fabry-Perot Research Articles

In situ monitoring of cycling characteristics in lithium-ion battery based on a two-cavity cascade fiber-optic Fabry-Perot interferometer

The state characterization inside the lithium-ion battery during charge/discharge cycling is extremely crucial for understanding the electrochemical reaction mechanism. However, current methods exhibit a challenge to overcome the specific battery environment obstacles, including strong redox properties, strong electromagnetic interference, and fast reaction processes. Hence, more efforts are still needed to monitor the actual state inside the battery accurately and reliably. To address this issue, we designed and developed a compact two-cavity cascade fiber-optic Fabry-Perot interferometer (FPI) sensor that can be safely implanted in batteries to measure internal temperature and pressure simultaneously. With its high pressure and temperature sensitivity of 26.6 ​nm/kPa and 107 ​nm/°C, this sensor exhibits an ultra-low cross-sensitivity of −40 ​Pa/°C. During charge/discharge cycling tests, regular cyclic pressure and temperature signals are obtained at various rates cycling in real-time and in situ, revealing details about the actual state characterization inside the battery. From the experiment results, the pressure inside the battery is divided into reversible changes caused by respiration effects and irreversible changes caused by trace gas production. Furthermore, the FPI sensor provides a more precise temperature than thermocouples that measure the surface temperature of the battery, reflecting the internal/external temperature difference to a maximum of 3.5 ​°C at 1 ​C rate cycling. This operando FPI sensor provides a valuable technological tool for battery performance testing and safety monitoring.

Self-injection-locked second-harmonic generation at 532 nm in high-Q Fabry-Perot micro-cavities

Based on the combination of DFB laser self-injection-locking (SIL) and external-cavity frequency-doubling, we have successfully demonstrated, for the first time to our knowledge, the self-injection-locked second-harmonic generation (SHG) at 532 nm by adopting the high-Q Fabry-Perot (FP) micro-cavities. With the DFB incident pump power of 79 mW at 1064 nm, the maximum output SHG power of 20.7 mW at 532 nm was achieved from the 11 mm long plane-concave FP external-cavity of 0.12 mL volume with the 10 mm long PPLN crystal. The corresponding output SHG efficiency of 26.2 % and the Q-factor of 56.5 M both exceeded all known SIL-SHG results reported, and the SIL SHG output power was one order of magnitude higher than the previous maximum of over 2 mW. The reliable SIL has been realized by utilizing the natural birefringence of the intracavity nonlinear crystal to provide laser feedback, and the intrinsic linewidth of the SIL pump laser at 1064 nm was about 30 Hz. Moreover, by replacing the PPLN crystal with the LN and KTP crystals, the output SHG power of 6.1 mW and 2.7 mW at 532 nm were respectively obtained with the Q-factors of 29.3 M and 27.6 M. Our new SIL-SHG design with the high-Q FP micro-cavity paves the way to a new type of the field-deployable ultra-narrow-linewidth visible and near-visible lasers of low size, weight, and power (SWaP).

Study on narrow linewidth 2.1 μm self-optical parametric oscillator based on Nd:MgO:PPLN

We report a 2.1 µm miniaturized narrow linewidth self-optical parametric oscillator (SOPO) based on Nd:MgO:PPLN crystal. We attained 2.1 µm narrow linewidth laser output by incorporating an Fabry-Perot (F-P) etalon into the SOPO. By controlling the crystal temperature uniformly, a stable 2.1 µm degenerate light output is obtained at 71 °C. Finally, when inserting the F-P etalon with a thickness of 2.5 mm, a maximum average output power of 0.65 W is obtained, corresponding pulse repetition rate is 60 kHz, the pulse width is 7.77 ns, the degenerate light beam quality M2 < 2. And the linewidth of 2168 nm laser is narrowed from 67.53 nm to 2.23 nm. It is proved by experiments that adding F-P etalon to the SOPO can narrow the linewidth of the 2.1 μm laser and optimize the beam quality. These findings provide technical support for the realization and application of narrow linewidth 2.1 µm laser, which is great significance for the further development of related fields.

High-Resolution and Large-Dynamic Range Fiber-Optic Sensors Based on Dual-Mode Direct Spectrum Interrogation Method

Conventional optical fiber temperature/strain sensors often have to make compromises between the resolution and the dynamic range. Here we present a new method that meets the measurement requirements for both high resolution and large dynamic range. A high-quality optical fiber Fabry-Perot Interferometer (FPI) constructed using a pair of chirped fiber Bragg gratings is employed as the sensor and a dual-mode direct spectrum interrogation method is proposed to identify the small drift of external temperature or strain. As a proof-of-concept illustration, a temperature resolution of 0.2 °C within 30–130 °C is demonstrated. For strain sensing, the resolution can be 10 µε within 0–1000 µε. The measurement resolution can be improved further by routinely increasing the reflectivity of the CFBG and the cavity length and the sensor can also be mass-produced. This new sensing schema not only resolves the conflict between the resolution and the dynamic range of fiber-optic temperature/strain sensors but can also be extended to other sensors and measurands.

Multiplexing and passive demodulation of intrinsic low-finesse Fabry-Perot interferometers using free-running DFB diode lasers

This paper presents a novel and simple technique for passive quadrature demodulation of multiplexed low-finesse fiber-optic Fabry-Perot interferometers. The approach proposed here uses two quadrature channels with very close wavelengths generated by two thermostabilized DFB diode lasers operating in continuous-wave mode. A coherent light correlation technique was used to demultiplex the wavelength channels and signals from interferometers at different positions along the fiber. The proposed technique does not require optical filters for spectral channel demultiplexing, making it suitable for demodulating relatively long interferometers with any free spectral range. An in-line array of four identical 13.1 cm long interferometers was used to demonstrate the method's performance. Experimental results demonstrate a phase resolution of 1.38 phase degrees, corresponding to a temperature resolution of 3 × 10−3 °C. Numerical simulations indicate that the main factor limiting the length of the sensing interferometer, and thus the resolution of the system, is the wavelength variation of the temperature-stabilized, independently operating lasers. The number of spectral channels can be easily extended to realize three or four-wavelength demodulation schemes.

Silicon‐Based 850 nm GaAs/GaAsP‐Strained Quantum Well Lasers with Active Region Dislocation Blocking Layers

A silicon‐based room temperature (RT) continuous wave (CW) operation quantum well (QW) laser emitting at 850 nm is reported in this article. By applying the dislocation filter superlattice, the threading dislocation density of the GaAs pseudosubstrate on Si is reduced to 1.8 × 107 cm−2. The metal‐organic chemical vapor deposition‐grown laser structure with GaAs/GaAsP QW and InAlAs active region dislocation blocking layer are fabricated into broad‐stripe Fabry–Perot laser diodes. A typical threshold current and threshold current density of 286 mA and 715 Acm−2 are obtained with 2 mm cavity length and 20 um stripe width samples. A 94.2 mW single‐facet output power lasing around 854 nm and a 0.314 WA−1 slope efficiency is measured under RT CW operation. After a 10‐min aging process, the tested laser can operate stably under continuous operation conditions at RT and the lifetime can be approximated using an exponential fitting curve, indicating a good life reliability of this QW laser.

Fiber optic strain sensor based on enhanced harmonic Vernier effect

In sensors utilizing the traditional harmonic Vernier effect, it is imperative to isolate the reference interferometer to mitigate the impact of external environmental fluctuations on the reference spectrum, thereby averting measurement inaccuracies. However, achieving such isolation between interferometers in compact fiber optic sensors poses significant challenges. We propose a fiber optic strain sensor based on the enhanced harmonic Vernier effect. In the enhanced harmonic Vernier effect, two interferometers are simultaneously involved in sensing. Hence, the isolation of interferometers is no longer a concern. Furthermore, the two interferometers exhibit responses with opposite signs, leading to a greater displacement of the envelope. Consequently, the sensitivity of the sensor is further enhanced without altering the harmonic order. Firstly, we conducted numerical simulations to analyze the enhanced harmonic Vernier effect. Secondly, we fabricated a Fabry–Perot interferometer (FPI) and a Mach–Zehnder interferometer (MZI) with strain sensitivity of opposite signs, generating a first-order harmonic. The experimental results indicate that the sensor’s sensitivity is 15.1 pm/μϵ, which is 1.41 and 2.80 times higher than the traditional harmonic Vernier effect using FPI and MZI as sensing interferometers, respectively. The proposed sensor and enhancement method hold promising potential for applications in high-sensitivity measurement fields.

Time–Frequency and Spectrum Analyses of All-Solid-State Self-Mode-Locked Burst Pulse Lasers

The theoretical and experimental characteristics of all-solid-state self-mode-locked burst pulse lasers are investigated in this study. The time–frequency and spectrum analyses of the lasers incorporating Fabry–Pérot (F-P) structures are presented, along with the development of the corresponding theoretical model. Self-mode-locked burst pulse lasers are experimentally constructed to reduce intracavity losses using the front and rear end surfaces of the gain media to form F-P structures. When the laser cavity length is 600 mm and the gain media lengths are 5, 6, and 10 mm, each burst pulse produced contains 56, 47, and 28 subpulses, respectively, with the same burst pulse width of 2 ns. The burst pulse train with beam quality M2 = 1.37 and an average output power of 0.23 W is obtained when the gain medium length is 5 mm and the pump power is 4.5 W. The corresponding burst pulse repetition frequency is 0.25 GHz and the subpulse repetition frequency is 13.66 GHz. The time–frequency spectral analyses of the laser signals provide a good representation of laser spectral information that even the currently available highest-resolution spectrometers cannot resolve.

Resonant-mode engineering for additive reflective structural colors with high brightness and high color purity

We present quad-layered reflective structural color filters generating vivid additive primary colors by controlling a mode number in a Fabry–Perot (FP) cavity and an anti-reflective (AR) coating layer, thus accomplishing high spectral contrast which is highly demanded in creating sharp colors. The reflection brightness of fabricated structural color filters is over 78% and a color gamut is comparable to the standard color gamut (sRGB). Higher-order resonant modes are exploited yielding a narrow passband with strong suppression of the reflection at shorter and longer wavelength ranges for a green color, while red and blue colors are produced by employing fundamental resonant modes. Besides, the structural color filters maintain both high brightness and high color purity at oblique incidence angles up to 40° due to a small angle of refraction by a cavity medium with high refractive index. Moreover, a large-scale fabrication is enabled owing to the simplicity of a device structure, where thin film deposition is used. The scheme presented in this work may open the door to a number of applications, such as reflective displays, imaging devices, colored photovoltaics, and decorations.

Quantification of macro-components in raw milk using micro NIR sensors

Near Infrared (NIR) spectroscopy is a rapid and proven method for the compositional analysis of raw milk; however, its usage is limited to laboratories due to instrumentation cost and bulkiness. The objective of this study was to investigate the potential of Fabry–Pérot Interferometer (FPI)-based micro NIR sensors to quantify macro-components in raw milk such as fat, protein, lactose, and total solids for in-situ analysis. An experimental prototype was designed to acquire the spectra of 250 raw milk samples in transmission mode using two micro NIR sensors. Calibration models were developed for macro-components of raw milk using partial least square (PLS) regression, and prediction performance was assessed using statistical metrics. It was observed that the sensor S-2.0 was able to quantify fat (RMSEP = 0.15 %), protein (RMSEP = 0.15 %) and total solids (RMSEP = 0.30 %). However, S-2.5 resulted in relatively lower prediction accuracy for fat (RMSEP = 0.35 %) and protein (RMSEP = 0.33 %), possibly due to the NIR region's lower penetration power where the sensor S-2.5 captures the response. The results showed that the micro/handheld NIR sensors could quantify certain macro-components (fat and protein) in raw milk, while they may not be suitable for other components (e.g., lactose).

Methane measurement method based on F-P angle-dependent correlation spectroscopy.

This study explores a gas measurement method based on Fabry-Perot (F-P) angle-dependent correlated spectroscopy, which achieves highly sensitive and selective gas measurements by adjusting the angle to match the F-P interference peak with the gas absorption peak. Methane (CH4) is the chosen target gas, and an F-P etalon is designed with parameters matching the CH4 absorption peak. An angle-scanning measurement system is established to enable correlated spectroscopic detection of CH4 gas. Angle-scanning measurements reveal distinct absorption signals at the angle where the F-P interference peak aligns with the CH4 absorption peak. Gas measurements of standard samples demonstrate a linear relationship between the apparent absorbance at the on/off positions and CH4 concentration, allowing for accurate CH4 concentration measurements. The study further investigates the detection limit of the experimental system, achieving a 3σ detection limit of 720 ppm under the on/off measurement mode. A conical incidence model is developed to analyze the impact of beam divergence angles on the transmittance of the F-P cavity. Simulations are conducted to assess absorption signals in the presence of extreme cross-interference, demonstrating the method's robust resistance to cross-interference. The F-P correlated spectroscopy method described in this paper, as a non-dispersive spectroscopic measurement technique, holds promise for designing high-sensitivity gas sensors and imaging applications.

Visual Strain Sensors Based on Fabry-Perot Structures for Structural Integrity Monitoring.

Strain sensors that can rapidly and efficiently detect strain distribution and magnitude are crucial for structural health monitoring and human-computer interactions. However, traditional electrical and optical strain sensors make access to structural health information challenging because data conversion is required, and they have intricate, delicate designs. Drawing inspiration from the moisture-responsive coloration of beetle wing sheaths, we propose using Ecoflex as a flexible substrate. This substrate is coated with a Fabry-Perot (F-P) optical structure, comprising a "reflective layer/stretchable interference cavity/reflective layer", creating a dynamic color-changing visual strain sensor. Upon the application of external stress, the flexible interference chamber of the sensor stretches and contracts, prompting a blue-shift in the structural reflection curve and displaying varying colors that correlate with the applied strain. The innovative flexible sensor can be attached to complex-shaped components, enabling the visual detection of structural integrity. This biomimetic visual strain sensor holds significant promise for real-time structural health monitoring applications.

Draw-tower-grating-based Fabry-Perot interferometers for simultaneous measurements of temperature and salinity.

In this paper, a fiber optic sensor with draw-tower-grating (DTG)-based Fabry-Perot interferometers (FPIs) are proposed to measure the temperature and salinity of seawater simultaneously. The sensing structure utilizes DTG as the reflector, and two adjacent gratings can be cascaded to compose an FPI. By employing moisture-sensitive materials to the surface of the optical fiber, the variation in salinity can be measured by the axial strain applied by the coating on the sensing optical fiber. The salinity altering causes swelling or shrinking actions of the coating through absorbing or releasing water. Two different moisture-sensitive materials are chosen to eliminate the cross-sensitivity of temperature and salinity. The experimental results show that the sensor exhibits linear response to temperature and salinity changes with good repeatability and stability, and the temperature and salinity sensitivities are 12308.65 rad/°C and 95.02 rad/‰, respectively. The optical path configuration of the DTG sensing array matching compensation interferometer provides the possibility for efficient distributed solutions, which has promising potential for application in marine engineering.

Monolithic optical resonator for ultrastable laser and photonic millimeter-wave synthesis

Optical resonators are indispensable tools in optical metrology that usually benefit from an evacuated and highly-isolated environment to achieve peak performance. Even in the more sophisticated design of Fabry-Perot (FP) cavities, the material choice limits the achievable quality factors. For this reason, monolithic resonators are emerging as promising alternative to traditional designs, but their design is still at preliminary stage and far from being optimized. Here, we demonstrate a monolithic FP resonator with 4.5 cm3 volume and 2 × 105 finesse. In the ambient environment, we achieve 18 Hz integrated laser linewidth and 7 × 10−14 frequency stability measured from 0.08 s to 0.3 s averaging time, the highest spectral purity and stability demonstrated to date in the context of monolithic reference resonators. By locking two separate lasers to distinct modes of the same resonator, a 96 GHz microwave signals is generated with phase noise -100 dBc/Hz at 10 kHz frequency offset, achieving orders of magnitude improvement in the approach of photonic heterodyne synthesis. The compact monolithic FP resonator is promising for applications in spectrally-pure, high-frequency microwave photonic references as well as optical clocks and other metrological devices. ©2024. All rights reserved.

SiNx/SiO2-Based Fabry-Perot Interferometer on Sapphire for Near-UV Optical Gas Sensing of Formaldehyde in Air.

Fabry-Perot interferometers (FPIs), comprising foundry-compatible dielectric thin films on sapphire wafer substrates, were investigated for possible use in chemical sensing. Specifically, structures comprising two vertically stacked distributed Bragg reflectors (DBRs), with the lower DBR between a sapphire substrate and a silicon-oxide (SiO2) resonator layer and the other DBR on top of this resonator layer, were investigated for operation in the near-ultraviolet (near-UV) range. The DBRs are composed of a stack of nitride-rich silicon-nitride (SiNx) layers for the higher index and SiO2 layers for the lower index. An exemplary application would be formaldehyde detection at sub-ppm concentrations in air, using UV absorption spectroscopy in the 300-360 nm band, while providing spectral selectivity against the main interfering gases, notably NO2 and O3. Although SiNx thin films are conventionally used only for visible and near-infrared optical wavelengths (above 450 nm) because of high absorbance at lower wavelengths, this work shows that nitride-rich SiNx is suitable for near-UV wavelengths. The interplay between spectral absorbance, transmittance and reflectance in a FPI is presented in a comparative study between one FPI design using stoichiometric material (Si3N4) and two designs based on N-rich compositions, SiN1.39 and SiN1.49. Spectral measurements confirm that if the design accounts for phase penetration depth, sufficient performance can be achieved with the SiN1.49-based FPI design for gas absorption spectroscopy in near-UV, with peak transmission at 330 nm of 64%, a free spectral range (FSR) of 20 nm and a full-width half-magnitude spectral resolution (FWHM) of 2 nm.

Permulaan Gelembung Plasma Khatulistiwa Semasa Angin Neutral Kuat dan Lemah di Asia Tenggara

Equatorial plasma bubbles (EPBs), which are depletions in the ionosphere disrupting radio waves, exhibit complex dynamics influenced by neutral winds. The present study aims to investigate the relationship between the onset of EPBs and the velocities of neutral winds. The onset of EPBs was determined from the rate of the Total Electron Content Index (ROTI) keogram obtained using Global Positioning System (GPS) data over the Southeast Asia sector. Meanwhile, thermospheric neutral winds were measured using a Fabry-Perot interferometer (FPI), and the height of the F layer was acquired from an ionosonde, both instruments positioned in Kototabang (KTB), Indonesia. The observations are classified into two cases based on the strength of winds: strong and weak winds on different nights. This study successfully reported the onset time and location of EPBs occurred at 1320 UT (2120 LT) and 100° (500 km) longitude, attributed to pre-reversal enhancement (PRE). We conclude that thermospheric neutral wind makes a significant contribution to the observed onsets of EPBs driven in the zonal direction. Therefore, this finding reinforces past studies that have shown an increase in the height of the F layer could play an important role in determining the onset of EPBs.

A novel direct detection lidar compatible with software-defined radio

This paper proposes a novel direct detection lidar compatible with software-defined radio, which can effectively absorb the advantages of radio frequency technology. The radio frequency signal is firstly loaded onto the output light of the lidar through a fiber phase modulator and then demodulated from its backward reflected light through a combination of fiber Fabry-Perot interferometer and photodetector. The generation of the transmitting radio frequency signal and the sampling and processing of the receiving radio frequency signal are completed by a software-defined radio. Theoretically, it has been proven that the range and velocity of the target cause phase delay and Doppler frequency shift of the radio frequency signal loaded on the lidar, just like using the radio frequency signal to directly detect the target in radar. In the experiment, by programming the software-defined radio, the ranging and velocimetry algorithms of radar have been applied to this lidar. The theoretical and experimental results indicate that the lidar proposed in this paper has software definable characteristics. Through programming, different functions can be achieved, and in the future, more advanced algorithms of radar can be easily transplanted to further improve its performance.

Hybrid mode for absorption enhancement in the Ga2O3 nanocavity photodetector with grating electrodes

Gallium oxide (Ga2O3) photodetectors have drawn increased interest for their widespread applications ranging from military to civil. Due to the inherent oxygen vacancy defects, they seriously suffer from trade-offs that make them incompetent for high-responsivity, quick-response detection. Herein, a Ga2O3 nanocavity photodetector assisted with grating electrodes is designed to break the constraint. The proposed structure supports both the plasmonic mode and the Fabry–Perot (F-P) mode. Numerical calculations show that the absorption of 99.8% is realized for ultra-thin Ga2O3 (30 nm), corresponding to a responsivity of 12.35 A/W. Benefiting from optical mechanisms, the external quantum efficiency (EQE) reaches 6040%, which is 466 times higher than that of bare Ga2O3 film. Furthermore, the proposed photodetector achieves a polarization-dependent dichroism ratio of 9.1, enabling polarization photodetection. The grating electrodes also effectively reduce the transit time of the photo-generated carriers. Our work provides a sophisticated platform for developing high-performance Ga2O3 photodetectors with the advantages of simplified fabrication processes and multidimensional detection.

High-accuracy optical vector network analyzer for optical notch and bandpass responses

A high-accuracy optical vector network analyzer (OVNA) based on optical carrier-suppressed double sideband (CS-DSB) modulation is proposed and experimentally demonstrated. The ±1st-order sideband signals are generated by CS-DSB modulation and then pass through the symmetric optical device under test (DUT). The band-stop or band-pass responses can be realized by detecting and processing the double frequency of the driven RF signal. Compared with the conventional symmetrical DSB-based OVNA, the measurement accuracy is improved by eliminating the errors caused by the even-order sidebands, and the complexity is reduced as the proposed method with only one step measurement can avoid the complex postprocessing. In addition, the optical carrier is aligned to the center frequency of the DUT by employing the Pound–Drever–Hall (PDH) technique, which provides stable measurement. At the same time, the limitation that the band-pass responses cannot be measured by the traditional single-sideband (SSB)-based OVNA is overcome. Additionally, accurate magnitude and phase responses of the DUT near the optical carrier can be also achieved since the proposed OVNA is optical filter-immune. The proposed method is theoretically analyzed and verified by experiment. A Fabry–Perot (FP) interferometer serves as the symmetric DUT; the band-stop responses in a frequency range of 6 GHz are obtained with a resolution of 1.2 MHz; and the band-pass responses with the range from 0 to 13 GHz offsetting the optical carrier are also obtained. The measurement time can reach up to 30 min with high stability. The proposed OVNA offers enhanced accuracy and a stable approach for applications in photonic systems and other innovations.

High-Q Fabry-Pérot Cavity Based on Micro-Lens Array for Refractive Index Sensing

Fabry-Pérot (FP) microcavities have attracted tremendous attention in recent years due to their favorable optical characteristics of the high quality (Q) factor and small mode volume. In this work, we presented a novel approach that utilized the soft lithography and imprinting technology to incorporate the convex micro-lens array structure into the FP (FP-lens) cavity. A strong mode-profile restriction of the micro-lens simultaneously reduced the mode volume and enhanced the Q factor, exhibiting high tolerance to non-parallelism of mirrors compared with that of the plane-plane FP (PP-FP) microcavities. In the experiment, the Q factor of the FP-lens cavity was measured to be 8.145×104, which exhibited a 5.6-fold increase than that of the PP-FP cavity. Furthermore, we experimentally measured the refractive index sensing performance of the FP-lens cavity with the sensitivity of 594.7 nm/RIU and a detection limit of 4.26×10−7 RIU. On the basis of this superior sensing performance, the FP-lens cavity has the great potential for applications in biosensors.