Extraction Of Cellulose Research Articles

Potential Utilization of Cocoa Waste from Gunung Kidul Cocoa Fermentation Center: The Influence of NaOCl in Cellulose Extraction from Cocoa Pod Husk

Potential Utilization of Cocoa Waste from Gunung Kidul Cocoa Fermentation Center: The Influence of NaOCl in Cellulose Extraction from Cocoa Pod Husk

Controlled reaction dynamics of cellulose: Revealing the dual morphology nanocrystals

Cellulose nanocrystals exhibit diverse morphology with embedded crystallinity derived from the ordered crystalline regimes of cellulose fibers. Acid hydrolysis parameters controls the morphology of nanocrystals and is the primary efficient route for the synthesis of cellulose nanocrystals. In this study, we explored the impact of temperature on the morphology engineering of cellulose nanocrystals derived from banana pseudostem by oxalic acid hydrolysis, an underexplored method. Confirmation of successful cellulose extraction was achieved through fibrous morphology observed in FESEM and TEM analyses. X-ray diffraction and Raman spectroscopy affirmed the presence of type II cellulose. Notably, for the first time, we report the derivation of toroidal and spherulitic sheet-like morphologies in cellulose nanocrystals synthesized by hydrothermal method from banana psuedostem. Our investigation revealed that cellulose hydrolysis at 120 °C yields nanocrystals characterized by toroidal and spherulitic sheet-like morphologies with excellent crystallinity, as confirmed by FESEM and TEM analyses, with average thicknesses of 13.70 nm and 18.05 nm, respectively. Interestingly, elevating the hydrolysis temperature to 180 °C led to the collapse of these structures into carbon dots, exhibiting notable cyan emission.

Extraction and Characterization of Cellulose from Coffee Husk and Brewery’s Spent Grain Fibers Using Alkali-Hydrogen Peroxide Treatment Method

Coffee husk (CH) and brewery spent grain (BSG) fibers are sustainable industrial residues that consist of cellulose. The present study aimed at the extraction of cellulose from CH and BSG fibers and to study the effect of alkali-hydrogen peroxide (5% NaOH–7% H2O2) treatment during the extraction by characterizing the extracted cellulose. Characterization of cellulose particles, such as crystallinity, functional groups, thermal properties, and morphology, was conducted by performing X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analyzer (TGA), and scanning electron microscopy (SEM), respectively. The finding shows that the maximum cellulose yields obtained from CH and BSG fibers are 37.3% and 26.5%, respectively. From the XRD results, the cellulose obtained from CH fiber (C-CH) and from BSG fiber (C-BSG) showed diffractive peaks with the highest intensity of approximately 1,003 and 1,236 counted at 2θ = 22°, respectively. A reduction in the absorption of peaks was observed on the FTIR spectrum for both C-BSG and C-CH samples at different wavelengths. SEM demonstrated that the surface roughness of the celluloses was enhanced. TGA showed that the maximum temperature decomposition observed for both C-CH and C-BSG is 360°C and 380°C, respectively. Generally, in this study, alkali-hydrogen peroxide (5% NaOH–7% H2O2) treatment was effectively used for the treatment of BSG and CH fibers for the extraction and surface modification of cellulose particles. The extracted cellulose in the present study can be used as an alternative to conventional cellulose for the manufacturing of biocomposite materials, preparation of particle boards and furniture, and production of food packaging materials.

Cellulose nanocrystals isolated from sugarcane bagasse using the formic/peroxyformic acid process: Structural, chemical, and thermal properties

Sugarcane bagasse (SCB) is a renewable biomass source for cellulose extraction. In the pretreatment, SCB is processed to break down the cellulose-lignin-hemicellulose matrix and isolate components. This work proposes a formic/peroxyformic acid process for extracting cellulose nanocrystals (CNCs) from SCB. Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, and solid-state 13C nuclear magnetic resonance (ss- 13C NMR) were employed to evidence the removal of wax, hemicellulose, and lignin from the raw SCB. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA) were used for analyzing crystallinity, morphology, and thermal properties. SEM results showed that after lignin removal, the size of purified cellulose fibrils decreased significantly, and the structure of cellulose microfibers became smoother and more apparent. After acid hydrolysis of bleached cellulose microfibers, XRD analysis showed CNCs had the highest crystallinity (70.8 %). In TEM images, rod-like structures of CNCs were measured to be 23 ± 2.7 nm wide and 610 ± 18 nm long. The eco-friendly formic/peroxyformic acid procedure with a chlorine-free bleaching stage produced a white, cellulose-rich solid powder of CNCs.

Quality of cellulose and biostimulant extracts from Oedogonium calcareum cultivated during primary wastewater treatment

A practical two-product cascading biorefinery was developed to extract a biostimulant and cellulose from the freshwater filamentous macroalga Oedogonium calcareum grown while treating primary wastewater. Biostimulant production provides a valuable extract with production of disinfected residual biomass for further product development. Both Escherichia coli and F-specific RNA bacteriophage, indicators of human pathogens contamination, were absent from the residual biomass. The chemical composition of the biostimulant was complex, consisting of growth-promoting substances, free amino acids, and minerals. The O. calcareum cellulose fractions yielded between 9.5% and 10.1% (w/w) with purities from 84% to 90% and closely resembled microcrystalline cellulose. Biostimulant extraction improved cellulose quality by increasing crystallinity from 59% to 62%. Biomass condition, drying process, and biostimulant production influenced the crystallinity index. This study demonstrates a two-step process of biostimulant and cellulose extraction from wastewater-grown Oedogonium, simultaneously disinfecting biomass and isolating high-quality cellulose as a sustainable alternative to conventional extraction methods.

Extraction of cellulose from halophytic plants for the synthesis of a novel biocomposite.

Cellulose nanofibers, a sustainable and promising material with widespread applications, exhibit appreciable strength and excellent mechanical and physicochemical properties. The preparation of cellulosic nanofibers from food or agricultural residue is not sustainable. Therefore, this study was designed to use three halophytic plants (Cressa cretica, Phragmites karka, and Suaeda fruticosa) to extract cellulose for the subsequent conversion to cellulosic nanofibers composites. The other extracted biomass components including lignin, hemicellulose, and pectin were also utilized to obtain industrially valuable enzymes. The maximum pectinase (31.56 IU mL-1), xylanase (35.21 IU mL-1), and laccase (15.89 IU mL-1) were produced after the fermentation of extracted pectin, hemicellulose, and lignin from S. fruticosa, P. karka, and C. cretica, respectively. Cellulose was methylated (with a degree of substitution of 2.4) and subsequently converted into a composite using polyvinyl alcohol. Scanning electron microscopy and Fourier-transform infrared spectroscopy confirmed the successful synthesis of the composites. The composites made up of cellulose from C. cretica and S. fruticosa had a high tensile strength (21.5 and 15.2 MPa) and low biodegradability (47.58% and 44.56%, respectively) after dumping for 3 months in soil, as compared with the composite from P. karka (98.79% biodegradability and 4.9 MPa tensile strength). Moreover, all the composites exhibited antibacterial activity against gram-negative bacteria (Escherichia coli and Klebsiella pneumoniae) and gram-positive bacteria (Staphylococcus aureus). Hence, this study emphasizes the possibility for various industrial applications of biomass from halophytic plants.

Changes in crystallinity of sago palm (Metroxylon sago spp.) waste during cellulose extraction

Changes in crystallinity of sago palm (Metroxylon sago spp.) waste during cellulose extraction

Extraction and characterization of microcrystalline cellulose from Vachellia nilotica plant leaves: A biomass waste to wealth approach.

Biobased waste utilization is an intriguing area of research and an ecologically conscious approach. Plant-based materials can be used to render cellulose, which is an eco-friendly material that can be used in numerous aspects. In the current investigation, cellulose was extracted from the leaves of the Vachellia nilotica plant via acid hydrolysis. The application of this research is specifically directed toward the utilization of undesirable plant sources. To validate the extracted cellulose, FT-IR spectroscopy was applied. The cellulose was measured to have a density of 1.234 g/cm3. The crystallinity index (58.93%) and crystallinity size (11.56 nm) of cellulose are evaluated using X-ray diffraction spectroscopy analysis. The highest degradation temperature (320.8°C) was observed using thermogravimetry and differential scanning calorimetry curve analysis. The analysis of particle size was conducted utilizing images captured by scanning electron microscopy. Particle size of less than 30 μm was found and they exhibit non-uniform orientation. Additionally, atomic force microscopy analysis shows an improved average surface roughness (Ra), which increases the possibility of using extracted cellulose as reinforcement in biofilms.

Manufacturing and Applications of Cellulosic Films in Packaging: An Alternative for Plastic Films

Background: Different synthetic materials are constantly being utilized as raw materials for packaging, which might have several drawbacks, like plastic, some of which have poor lifespans. Plastic can get damaged, scratched, or fractured over time, easily take in tastes and fragrances, and significantly affect the environment and health. Excessive plastic waste may lead to environmental pollution and related consequences. Plastics that contaminate food have also been linked to health problems like high blood pressure, heart palpitations, headaches, nausea, diarrhea, and flushing. Objective: The present review entails the hazards associated with the usage of plastic as a packaging material and highlights the necessity to reduce its use and promote alternatives and sustainable production. Thus, the present review portrays the need for biopolymers, types of plant polymers, methods of cellulose extraction and derivatization, the manufacturing process of cellulosic films and thereby use as film and coatings for food preservation. The current review also summarizes different quality control tests for effective utilization as an alternative to synthetic polymers. Conclusion: Different polymers derived from agricultural products are excellent candidates for creating packaging materials. Similar to polysaccharides, these polymers, including nanocomposites, films, composites, etc., are helpful in a wide range of applications. Cellulose, one of the most widespread polysaccharides in the world, offers a variety of appealing special qualities. It appears reasonable and must be considered that cellulose can be used effectively as a raw material for packaging. In this review, we explore how cellulose is used in the packaging industry to make composites, coating materials, and edible and non-edible films.

Fine extraction of cellulose from corn straw and the application for eco-friendly packaging films enhanced with polyvinyl alcohol

Biomass materials substituting for petroleum-based polymers occupy an important position in achieving sustainable development. Cellulose, a typical biomass material, stands out as the primary choice for producing eco-friendly packaging materials. However, it is still a challenge to efficiently utilize cellulose from waste biomass materials in practice. Herein, cellulose-based films were prepared by pretreating waste corn straw, separating straw husk, straw pith and straw leaf, and extracting cellulose through alkali and sodium chlorite treatment to improve its mechanical properties using the cross-linked polyvinyl alcohol (PVA) method in this work. The prepared composite films were characterized by Fourier transform infrared spectrometer (FTIR), X-ray diffraction instrument (XRD), Scanning electron microscopy (SEM), Thermogravimetric (TG) and mechanical properties. The results indicated that corn straw husk exhibited the highest cellulose content of 31.67 wt%, and obtained husk cellulose had the highest crystallinity of 52.5 %. Compared to corn straw, the crystallinity of husk cellulose, pith cellulose and leaf cellulose increased by 19.5 %, 16.4 % and 44.1 %, respectively. Husk cellulose/PVA composite films were the most thermally stable, with a maximum weight loss temperature of 346.8 °C. In addition, the husk cellulose/PVA composite film had the best tensile strength of 37 MPa. Meanwhile, the composite films had good UV shielding, low water vapor transmission rate and biodegradability. Therefore, this work provides a fine utilization route of waste corn straw, and as-prepared cellulose based films have potential application in eco-friendly packaging materials.

Structural characterization of the polysaccharide from the black crystal region of Inonotus obliquus and its effect on AsPC-1 and SW1990 pancreatic cancer cell apoptosis

In this study, one water soluble polysaccharide (IOP1–1) with a weight average molecular weight of 6886 Da was obtained from the black crystal region of Inonotus obliquus by hot water extraction, DEAE-52 cellulose extraction and Sephadex-100 column chromatography purification. Structural analysis indicated that IOP1–1 was a glucan with a main chain composed of α-Glcp-(1 → 4)-α-Glcp-(1 → 4)-β-Glcp-(1 → 4)-β-Glcp-(1 → 4)-α-Glcp-(1 → 6)-β-Glcp-(1 → 4)-α-Glcp-(1 → 3)-β-Glcp-(1→. The CCK-8 assay results showed that IOP1–1 inhibited AsPC-1 and SW1990 pancreatic cancer cell proliferation in a concentration-dependent manner. Flow cytometric analysis revealed that IOP1–1 induced cell cycle arrest in AsPC-1 and SW1990 cells. Hoechst 33342 staining and Annexin V-FITC/PI double staining analysis showed that IOP1–1 could induce apoptosis in AsPC-1 and SW1990 cells. Furthermore, western blot analysis confirmed that IOP1–1 could induce apoptosis in AsPC-1 and SW1990 pancreatic cancer cells through three pathways: the mitochondrial pathway, the death receptor pathway, and endoplasmic reticulum stress. According to these research data, IOP1–1 may be utilized as an adjuvant treatment to anticancer medications, opening up new application prospects and opportunities.

Microwave assisted extraction of cellulose from lemon grass: Effect on techno-functional and microstructural properties

The study focused on utilizing lemon grass straw to generate cellulose through the process of delignification, which involves the removal of hemicelluloses, followed by bleaching. The study involves the microwave-assisted alkali extraction, followed by characterizing the extracted material. At microwave power of 540 W using 8 % NaOH for 3 min for lignin removal and 540 W for 2 min for bleaching showed the maximum yield of 37.46 %. Fourier transform infrared spectroscopy is employed to analyze the physical properties of extracted cellulose, namely the hydroxyl (OH), carbonyl (C=O), C–H bonds, C–O and C–C bonds, and glycosidic linkage (C–O–C) within the cellulose polymer chain. The extracted cellulose exhibited excellent thermal stability, as indicated by its high breakdown temperature. The X-ray diffraction (XRD) analysis revealed prominent peaks at 14.8°, 16.5°, and 22.5°, demonstrating the presence of crystalline cellulose. The crystallinity index value of 70.02 % further confirmed the crystalline nature of the extracted cellulose.

Investigation of Cellulose-Based Materials Applied in Life Sciences Using Laser Light Scattering Methods.

This review emphasizes the practical importance of laser light scattering methods for characterizing cellulose and its derivatives. The physicochemical parameters like molecular weights, the radius of gyration, hydrodynamic radius, and conformation will be considered when the reproducibility of polymer behavior in solution is necessary for the subsequent optimization of the property profile of a designed product. Since there are various sources of cellulose, and the methods of cellulose extraction and chemical modification have variable yields, materials with variable molecular weights, and size polydispersity will often result. Later, the molecular masses will influence other physicochemical properties of cellulosic materials, both in solution and solid state. Consequently, the most rigorous determination of these quantities is imperative. In this regard, the following are presented and discussed in this review: the theoretical foundations of the light scattering phenomenon, the evolution of the specific instrumentation and detectors, the development of the detector-coupling techniques which include a light scattering detector, and finally, the importance of the specific parameters of polymers in solution, resulting from the data analysis of light scattering signals. All these aspects are summarized according to the chemical classification of the materials: celluloses, esters of cellulose, co-esters of cellulose, alkyl esters of cellulose, ethers of cellulose, and other heterogeneous cellulose derivatives with applications in life sciences.

Extraction and Characterization of Cellulose from Broccoli Stems as a New Biopolymer Source for Producing Carboxymethyl Cellulose Films.

The use of food and agricultural waste-derived carboxymethyl cellulose (CMC) has become of interest due to their biodegradability and cost-effectiveness. In the current research, cellulose was extracted from broccoli stems to produce carboxymethyl cellulose using a carboxymethylation reaction via chloroacetic acid (CAA) and sodium hydroxide (5-10 M). The effects of different synthesis conditions on the degree of substitution (DS) and viscosity of the synthesized CMC powder were investigated. The mechanical properties, water vapor permeability (WVP), and colour of CMC films were also evaluated. The results showed that CMC with the highest DS value (0.60) and the highest viscosity of 0.5 Pa·s could be synthesized from broccoli stems at a concentration of 7.5 M NaOH and a cellulose-to-chloroacetic acid ratio of 1 : 1.2. At CMC concentration of 4 g/100 mL with 0.8 g/100 mL of glycerol, the films had the highest tensile strength (31.91 MPa), whereas with 1.2 g/100 mL glycerol, more flexible films with elongation at break of 27.56% were produced. CMC films with the highest WVP (7.87 × 103 gm2·mmHg-1/day) were made with 6 g/100 mL of CMC and 1.8 g/100 mL of glycerol. This research proposes a new source of cellulose to produce biodegradable packaging materials to initiate a practical basis for food waste reuse.

Integral valorization of two-phase olive mill waste: extraction of cellulose and lignin and their characterization

Integral valorization of two-phase olive mill waste: extraction of cellulose and lignin and their characterization

A Novel Microfiber Cellulose from Paederia foetida Stems: Characterization of Physical, Morphology, Thermal, and Chemical Properties

Abstract The Paederia foetida (PF) stem’s abundant and environmentally friendly novel nanocellulose has immense potential as a reinforcing agent for bio-nanocomposites. This work aims to investigate the physical, thermal, chemical, and morphological properties of cellulose microfibrils from Paederia foetida stems (CMFPFs). Sodium chlorite, acetic acid, and 5 % sodium hydroxide were used to perform bleaching and mercerization operations to extract cellulose. Chemical composition, X-ray diffraction (XRD) analysis, Fourier transform infrared spectroscopy, density, moisture content, examination of cellulose morphology using field emission scanning electron microscopy, and thermal stability were assessed using thermogravimetric analysis. The outcomes showed that the delignification and mercerization methods, respectively, removed lignin and hemicellulose from the extracted cellulose. Higher crystallinity was produced from chemically treated fibers, according to XRD examination. The CMFPF sample had a crystallinity index of 97.9 %, which was higher than the raw PFs (81.9 %) and bleached PFs (84.38 %). The maximum crystallinity was identified for CMFPFs, which had the lowest moisture content, fiber diameter, and density of the samples. After bleaching and mercerization have been applied to the fiber, changes in functional groups take effect.

Effect of ultrasound-advanced oxidation processes for pretreatment of oil palm mesocarp fiber for cellulose extraction

Effect of ultrasound-advanced oxidation processes for pretreatment of oil palm mesocarp fiber for cellulose extraction

Pu-erh tea-derived cellulose exhibits superior water/oil holding capacity compared to black and green tea celluloses: A comprehensive analysis

In this study, residues from black, green, and Pu-erh teas were used as raw materials to extract cellulose through alkali treatment and two-stage bleaching process. The structure and properties of the tea celluloses were compared. The yield and purity of the cellulose ranged from 6.3% to 10.1% and 75.5%–88.9%, respectively. The celluloses exhibited a typical bundle fiber morphology and an I-type crystal structure, with the Iβ structure being the predominant allomorph. Crystallinity was highest in Pu-erh tea cellulose (54.8%), followed by black tea cellulose (52.6%), and green tea cellulose (47.4%). Green tea cellulose displayed the highest initial thermal degradation temperature, while Pu-erh tea cellulose had the lowest. Pu-erh tea cellulose showed the highest moisture absorption rate (12.6%), water holding capacity (10.1 g/g), and oil holding capacity (5.7 g/g), whereas these values were lowest in black tea cellulose. The correlation coefficient between Iβ structure content and water holding capacity is −0.90, and −1.00 with oil holding capacity. This study not only opens new pathways for the recycling of tea residues and their application in food packaging but also highlights the potential of tea-derived cellulose as an innovative material for dietary fiber resources with excellent water/oil holding capacities.

Preparation and Characterization of Cellulose Derivatives from Agricultural Wastes

Background: Rice straw was pretreated with dilute alkaline and acid solutions to extract cellulose, which was then converted into cellulose acetate with acetic anhydride and phosphotungstic acid (H3PW12O40·6H2O). The concentration of KOH and the duration of immersion in acetic acid solution affected the removal of hemicellulose and lignin, and after pretreatment with 4% KOH and immersion in acetic acid for 5 hours, the treated rice straw contained 83wt.% cellulose. Phosphotungstic acid has been shown to be an excellent catalyst for the acetylation of rice straw cellulose. The degree of substitution (DS) values had a substantial effect on the solubility of cellulose acetate, and acetone-soluble cellulose acetate with DS values about 2.2 can be generated by varying the amount of phosphotungstic acid and acetylation duration. Objectives: The aim of the study was to evaluate the preparation and characterization of cellulose derivatives from agricultural wastes. Methods: This cross-sectional study was carried out in the Department of Communicable Diseases Control, Director General of Health Services, Dhaka, Bangladesh. For this investigation the rice plant straw was collected from Magura district region. The collected straws were then treated with 3 wt% nitric acid and 1.5 wt% NaOH solution separately. Statistical analyses of the results were be obtained by using window-based Microsoft Excel and Statistical Packages for Social Sciences (SPSS-24). Results: This study observed that the rice straw contained about 35.67% cellulose, 5.50% hemicellulose and 30.18 % α-cellulose. And the wheat straw contained about 43.99% cellulose, 7.30% hemicellulose and 36.70% α-cellulose. The degree of acetylation and degree of substitution of the synthesized cellulose acetate from rice straw were 39.046% and 2.413 respectively. On the other hand, the degree of acetylation and degree of substitution of the synthesized cellulose acetate from wheat straw were 40.79% and 2.59 respectively. ....

SQUEAKY CLEAN CELLULOSE: COMPARING PRETREATMENT EFFECTIVENESS ON SINGLE TREE RINGS AND WOODEN LATHS

ABSTRACT Obtaining accurate radiocarbon (14C) results from wood samples requires the extraction of cellulose. In the past, this has been done using different combinations of methods including acidified bleaching, acid-base-acid, and strong bases. This often becomes a time-consuming task in most analyses, especially when single ring isotope chronologies are needed from wood samples. Using 14C and Fourier-transform infrared spectroscopy (FTIR), we tested four different pretreatment methods to determine their ability to produce high quality cellulose. We then adjusted the best methods to determine a method for pretreating wood laths of multiple rings. A sequence of base-acid-base-acid-bleach + strong base (BABAB+) and BABAB produced the most accurate results when compared to the Bomb20 Northern Hemisphere Zone 1 curve with an average difference in Δ14C of 1.3‰ and 5.8‰ respectively. These methods were adjusted to pretreat an entire wood lath and a comparison of the FTIR results suggest that our adjusted BABAB+ and BABAB produced high quality cellulose comparable to that of an individually pretreated ring. The possibility to pretreat wood lath samples has the potential to more than double the number of tree rings which can be pretreated in a week. This is a significant reduction in time when creating long tree ring chronologies.