External Gas Research Articles

Research on printed circuit board external open-circuit failure gas discharge tube under short-circuit failure

Research on printed circuit board external open-circuit failure gas discharge tube under short-circuit failure

An Artificial Olfactory System Based on a Chemi-Memristive Device.

Technologies based on the fusion of gas sensors and neuromorphic computing to mimic the olfactory system have immense potential. However, the implementation of neuromorphic olfactory systems remains in a state of infancy because conventional gas sensors lack the necessary functions. Therefore, this study proposes a hysteretic "chemi-memristive gas sensor" based on oxygen vacancy chemi-memristive dynamics that differ from that of conventional gas sensors. After the memristive switching operation, the redox reaction with the external gas molecules is enhanced, resulting in the generation and elimination of oxygen vacancies that induce rapid current changes. In addition, the pre-generated oxygen vacancies enhance the post-sensing properties. Therefore, fast responses, short recovery times, and hysteretic gas response are achieved by the proposed sensor at room temperature. Based on the advantageous functionality of the sensor, device-level olfactory systems that can monitor the history of input gas stimuli are experimentally demonstrated as a potential application. Moreover, analog conductance modulation induced by oxidizing and reducing gases enables the conversion of external gas stimuli into synaptic weights and hence the realization of typical synaptic functionalities without an additional device or circuit. The proposed chemi-memristive device represents an advance in the bioinspired technology adopted in creating artificial intelligence systems.

Modeling microvoiding kinetics of rare‐earth disilicates in flowing atmospheres containing water vapor

AbstractRare‐earth disilicate (REDS, RE2Si2O7) layers that may be used as environmental barrier coatings (EBCs) on ceramic matrix composite (CMC) components in high‐temperature stages of turbine engines are subject to microvoiding to form porous rare‐earth monosilicate (REMS, RE2SiO5) layers in flowing atmospheres containing water vapor. A simple microvoiding kinetic model that incorporates both mass transfer of the reaction product Si(OH)4(g) through the external gas phase boundary layer and pore diffusion of Si(OH)4(g) through the microvoided layer has been developed. Model predictions are in good agreement with measured growth rates of microvoided layers under low‐flowrate steam furnace test and high‐flowrate burner rig conditions. Since pore diffusion is generally the rate‐limiting step for EBC microvoiding in turbine engines, furnace testing under conditions of kinetic control by gas phase mass transfer is not generally capable of predicting REDS microvoiding rates under engine conditions. The kinetic model can be extended to incorporate changes in pore size and distribution, cracking of the microvoided layer, and introduction and cracking of an additional REMS topcoat to the system. The model can be used to generate a reasonable prediction of the time required to fully microvoid a REDS EBC layer on a CMC component in the hot gas path of an aircraft engine or stationary gas turbine.

An electrolytic bubble column with an external hollow fiber membrane gas–liquid contactor for effective microbial electrosynthesis of acetate from CO2

Currently, almost all microbial electrosynthesis (MES) reactors were biofilm-driven whether the cathode electron transfer was direct or indirect. It has been proven that cathode biofilm formation is time-consuming, and the current density achieved on these biofilms was relatively low. However, the main challenge for the non-biofilm-driven MES is how to maintain a good Columbic efficiency (CE) at high current densities. Here, we report a novel electro-H2 bubble column reactor with an external hollow fiber membrane gas–liquid contactor to tackle the challenge. The electrolyzer was placed at the bottom of the reactor to produce H2 micro-bubbles (mean diameter 169 ± 7 µm) at a current density of 156 A/m2. The bubble column was put on the top of the cathodic chamber of the electrolyzer to extend the H2 retention time, while the hollow fiber membrane gas–liquid contactor in the external loop was used to recover the unused gas. Consequently, the homoacetogens in reactor could efficiently convert the electrolytically-produced H2 and the externally-supplied CO2 into acetate. The volume of the catholyte (5.5 L) in this reactor is one order of magnitude higher than all reported MES reactors. Batch tests with enriched homoacetogens demonstrated a maximum acetate production rate (1.15 g/Lcatholyte/d, 898 g/m2cathode/d), acetate titer (34.5 g/L) could be achieved in this setup, and the average (maximum) CE of the electron to acetate efficiency was 64% (92%). Besides, dissolved H2 measurement and bacteria community analysis indicated the high acetate titers were likely caused by the H2 oversaturation situation and good substrate/product mass transfer rather than the selection of certain types of homoacetogens. The electro-H2 bubble reactor seems to be a promising MES setup for scale-up and practical application.

Clinical effectiveness of phospholipids in patients with restrictive respiratory failure due to lung tissue inflammation

Objective — to analyze the clinical effectiveness use of phosphatidylcholine liposomes in the treatment of patients with restrictive respiratory failure caused by acute pneumonia and pneumonia with a prolonged course.
 Materials and methods. A prospective cohort study of 68 people was conducted on the basis of the pulmonology department of the Kirovohrad Regional Hospital of the Kirovohrad Regional State in 2020—2021. The people were divided into two groups: I (n = 20) — control group, II (n = 48) — experimental group. They were composed of men aged 25 to 40 years. The first group consisted of healthy individuals who underwent a preventive examination. The second group included patients who, in addition to the traditional treatment of pneumonia, were treated with phospholipids in liposomal form. The drug was used by inhalation according to the instructions. In the course of the experiment, the volume-time indicators of external respiration and gas exchange of the body were studied in dynamics.
 Results and discussion. The introduction of phospholipids in liposomal form had a positive effect on the restoration of the function of external respiration from the 5th day of treatment of the disease. This is evidenced by the gradual normalization of breathing rate and respiratory volume. It was shown that the ratio of alveolar ventilation and minute respiratory volume was significantly lower and ranged from 60.3 to 72.7 % (with a control value of 72.2 to 77.4 %). Oxygen consumption increased by approximately 76 % on the 5th day of the disease, which indicates a pronounced increase in the level of oxidative metabolism in the body during this pathological process. Recovery could be observed due to optimization of the body’s oxygen supply. Regarding carbon dioxide release, this indicator was almost 2.3 times higher than the control values ​​on the 5th day of the disease. This contributes to the development of metabolic acidosis, which in turn leads to respiratory alkalosis. Against the background of phosphatidylcholine liposomes treatment, this indicator gradually decreased and had a tendency to approach control values ​​a month after treatment (0.216 ± ± 0.042) l/min). Another of the studied indicators is the dead breathing space. According to this indicator, the efficiency of external breathing also increased. The minute volume of blood flow in healthy individuals was (6.5 ± 0.7). During the disease, it decreased to (4.7 ± 0.8) with gradual recovery, starting from the 10th day of treatment with phospholipids. There is also a decrease in the oxygen saturation of the arterial blood and a decrease in the use of oxygen, which can be judged by the characteristics of the venous blood; at the same time, the determined oxygen consumption increases due to hyperventilation. One month after the treatment, these indicators were no longer significantly different from the control values. A similar trend is noted in the analysis of oxygen tension in arterial and venous blood, with a gradual normalization of indicators against the background of the use of phosphatidylcholine liposomes. The determination of the alveolar-arterial difference in oxygen showed an increase in the indicator in the experimental group compared to the control group. Most of the indicators we studied contributed to the decrease in oxygen, thus increasing the efficiency of external respiration.
 Conclusions. Phosphatidylcholine liposomes are an effective means of complex therapy of pneumonia. The drug has a normalizing effect on the level of energy metabolism in the body and normalizes oxygen consumption, contributing to a faster recovery of the optimal intensity of metabolic processes.

A model for describing advective and diffusive gas transport through initially saturated bentonite with consideration of temperature

Understanding the gas migration mechanism in an initially saturated bentonite is of great importance for evaluation of the long-term performance of a deep geological repository for disposal of high-level radioactive wastes. Previous researches usually neglect the gas diffusion process, but adopted the advective gas flow theory (visco-capillary flow or dilatant gas flow) to describe the gas transport in the initially water-saturated bentonite clays. In this study, gas migration process was regarded as results of a combination of diffusive transport of dissolved gas through pore water and advective flow along the gas pathways formed in the bentonite matrix. Meanwhile, dilation of the gas flow pathways with variation of the external stress and gas pressure during the advective flow was also considered. Based on this concept, a new model was proposed to describe the advective and diffusive gas transports with consideration of temperature. Validation was conducted using the gas injection tests performed under different boundary conditions in literature. Comparisons show that the diffusion and advection-controlled process provided by the proposed model can effectively simulate gas transport in the compacted GMZ bentonite. For gas migration under lower injection pressures, the contributions of advective gas flow to the gas flux are comparable to that of diffusion. With the increase of the injection pressure, the advective gas fluxes would gradually dominate over the diffusive transport. Meanwhile, predicted degree of saturation of the compacted bentonite is maintained at above 99% during the whole gas migration process, indicating that advective movement of gas was highly discrete in initially saturated bentonite.

Economic Analysis of Gas Supply System For Dual Fuel Engines With Life Cycle Cost

The regulations of the international maritime organization (IMO) on ship emission are becoming increasingly strict. Liquefied natural gas (LNG) is an ideal alternative fuel for vessels, considering its environmental and economic advantages. This paper compares the life cycle cost (LCC) of LNG ships low pressure gas supply system (FGSS). Comparative analysis of the three main pressurization modes for supplying LNG in the low pressure gas supply system, namely external gas source pressurization, self-pressurization and cryogenic pump boost. Through modeling in Aspen HYSYS software, system operation is simulated, life cycle costs are compared, and the implementation effects of the three system schemes are analyzed and evaluated. The application of life cycle economic analysis in ships mainly focuses on the overall energy saving and emission reduction of ships. Its application in low pressure gas supply systems for dual-fuel engines is rare. This study helps the gas supply system choose the most economical and applicable scheme in practical applications.

Performance assessment and multiobjective optimization of a biomass waste-fired gasification combined cycle for emission reduction

The use of renewable fuels leads to reduction in the use of fossil fuels and environmental pollutants. In this study, the design and analysis of a CCPP based on the use of syngas produced from biomass is discussed. The studied system includes a gasifier system to produce syngas, an external combustion gas turbine and a steam cycle to recover waste heat from combustion gases. Design variables include syngas temperature, syngas moisture content, CPR, TIT, HRSG operating pressure, and PPTD. The effect of design variables on performance components such as power generation, exergy efficiency and total cost rate of the system is investigated. Also, through multi-objective optimization, the optimal design of the system is done. Finally, it is observed that at the final decisioned optimal point, the produced power is 13.4 MW, the exergy efficiency is 17.2%, and the TCR is 118.8 $/h.

Working mechanism and testing of emergency reinforced airbag used for blocking in tunnels

During the construction and operation of tunnels, disasters, such as groundwater leakage, gushing water, and toxic gas diffusion, occasionally occur. The frictional resistance between an emergency airbag and the tunnel is used to resist external pressure, and gases or fluids can be isolated on one side of the airbag. Thus, more time can be gained for rescue and emergency repair. The external pressure that conventional airbags can resist is limited by their internal pressure, but increasing the internal pressure requires higher material strength and is uneconomical. Based on research on the force characteristics and failure mechanism of conventional airbags, a method for improving the blocking ability by reinforcing conventional airbags is proposed. A force analysis model of the reinforced airbag under external pressure is established, the reinforcement mechanism is revealed, and the calculation formula for the critical external pressure is obtained. Through model tests and full-scale field tests, the effect of improving the blocking ability of the reinforced airbag is verified, and the accuracy of the theoretical calculation formula is proved. The research shows that the reinforcement method is economical and effective, can greatly improve the blocking ability, and provides a theoretical analysis and practical application basis for emergency airbag design.

Vibration characteristics control of hybrid radial gas foil bearing-rotor system: Simulation and experiment

Currently, tiny, high-speed rotating machines frequently employ air foil bearings. Air is employed as the working medium, however, when the rotor speed is high, the rigidity of the air film is insufficient, which restricts the usage of air foil bearings. This study utilizes the external gas supply method of hydrostatic gas bearings to strengthen the air film stiffness of air foil bearings. The original air foil bearings are combined with external gas supply piping to create the hybrid gas foil bearing(HGFB), which may be utilized to increase the air film support stiffness of the bearings through the external gas supply. Additionally, by altering the gas supply pressure, this bearing may be used to actively manage the vibration characteristics of the shaft system, allowing the bearing performance to be adjusted to changing operating conditions. The static and dynamic properties of the HGFB with a 24 mm diameter are solved in this study using Newton's iterative approach and the finite difference method. The bearing-rotor system is modeled using this information. An Analysis is done on the impact of various air supply pressures and throttle hole widths on bearing performance and vibration characteristics of the shaft system. In this article, the vibration parameters of the bearing-rotor system are tested using an open-loop control test. The open-loop control experiment on the vibration response of the bearing-rotor system is performed using HGFBs with orifice sizes of 0 mm, 0.2 mm, 0.4 mm, 0.6 mm, 0.8 mm, and 1.0 mm. The experimental results confirm the accuracy of the simulation results. Correspondingly, this paper conducted closed-loop control comparison experiments on the vibration properties of the bearing-rotor system using the PID control method and the fuzzy PID control method in succession. It then evaluated the control effect of the two control strategies on the vibration of the bearing-rotor system and managed to improve the conventional PID control method used for gas bearings.

Sintering of silicon carbide obtained by combustion synthesis

An activated combustion synthesis method was utilized to synthesize silicon carbide from the elementary mixture in the presence of polytetrafluoroethylene (PTFE) as a thermochemical promoter and product's morphology modifier. Thermodynamic calculations in the initial Si–C-(C2F4)n mixture revealed the influence of PTFE amount and external gas pressure on the adiabatic temperature and equilibrium composition of the products. Combustion parameters and phase composition of the product were sensitive to silicon particle size, PTFE amount, sample diameter and gas pressure. Optimum conditions for the preparation of a mixture of alpha and beta SiC with up to 200 nm in particle size were determined. After consolidation by the spark plasma sintering technique some physicomechanical characteristics of the bulk specimens were measured.

External heating-induced thermal runaway and gas venting characteristics of polymer lithium-ion cells with LiNixCoyMnzO2 cathode

Thermal runaway is an important issue in the process of storage and application of lithium-ion cells. Herein, to better grasp gas venting characteristics and assess its risk, several sets of thermal runaway experiments and hazard analysis were conducted on polymer lithium-ion cells under external heating. Results demonstrate that 50–100% SOC cells exhibit fierce venting accompanied by higher surface temperature, temperature rate, voltage dropping, and mass loss compared to 25% SOC cells. The gas centerline temperature distribution covered with venting oscillation conforms to piecewise exponential expressions of height and heat release rate. The venting rate and internal pressure were deduced by temperature and mass loss, which increase monotonously with SOC increasing. The maximum heat release rate increases from 1.45 kW to 5.54 kW for 50–100% SOC cells, while it rapidly rises to 73.3 kW for 100% SOC cells under a secondary ignition. The heat release rate predicted by mass loss or flame surface area coincides well with experimental results. Besides, the asphyxiant harm of the gas emission was also evaluated by the fractional effective dose method. The findings give guidance for process safety evaluation, fire prevention and rescue in a real practical engineering utilization of cells.

Seal materials in flexible plastic food packaging: A review

AbstractFlexible packaging has many advantages in the food industry, arising from low weight, formability, multilayer complexity and cost. Heat sealing is a very efficient technique to close flexible food packaging. Currently, many thermoplastic materials are used in seal layers. A seal can be formed when these materials are heated and brought into contact; thereafter, polymer chains diffuse across the seal interface and entangle. Hydrogen bonds, polar and ionic interactions are molecular forces that can come into play, depending on the thermoplastic materials that are used in the seal layer. Bonds between identical polymers, referred to as autohesion, are formed in pouch applications (e.g., horizontal and vertical form‐fill‐seal packages). In lidding applications, the flexible film is sealed to a rigid cup, tray or bottle, whereby bonds can be formed between non‐identical polymers because the materials are often provided by different suppliers. All heat seal technologies imply heating of seal layers but differ in the heating principle. In the food industry and in most scientific seal studies, the seals of mono‐ and multilayered packaging are mainly formed by conductive heating. Recently, the use of emerging technologies, such as ultrasonic and laser heating, is increasingly described in recent papers. Applied seals are characterized by strength after a specified cooling time. Immediately after heating, this strength is referred to as hot tack. A good seal performance is crucial to guarantee food safety and quality. Besides strength, tightness is important to prevent food degradation, caused by microorganisms and external gases, and to keep aromatic gases inside the package. This review aims to give a literature overview that can support stakeholders in the food industry to improve and optimize the material selection in flexible packaging, in order to obtain seals with desired tightness and strength. Heat seal studies on materials and seal technology of flexible food packaging, such as pouches and lidding films, are considered. Scientific data are categorized from a materials' perspective, based on chemical structure, which is revealed by chemical and thermal analysis. A majority of the seal studies is categorized in a first section on polyolefins as seal layers. The following sections describe the seal functionality of (i) ethylene copolymers, such as ionomers; and (ii) polyesters, such as poly (ethylene terephthalate), pol (lactic acid) and poly (butylene succinate). The role of plasticizers, fillers and other additives in the seal performance is also described. Finally, material properties, such as chain length and melting temperature (Tm), as underlying causes of seal performance, are summarized.

A study on the combustion performance and NOx emissions characteristics of a novel U-type radiant tube based on MILD combustion theory

Based on the theory of moderate or intense low-oxygen dilution (MILD) combustion, a 3D steady-state CFD model coupling dual flue gas recirculation and dispersion combustion was developed to describe the flow field, combustion temperature field, wall temperature distribution, and NOx concentration field during the operation of a novel U-type radiant tube (N-URT). A user-defined function (UDF) method was implemented to simulate the dilution of O2 concentration in the combustion air due to external flue gas recirculation (E-FGR). The effects of the E-FGR ratio on combustion characteristics and NOx emission were evaluated. The simulated results were consistent with experimental results. The simulated NOx concentration at the outlet was reduced to 105.5 mg/m3 at 8% O2, which was about 35.2% lower than the conventional combustion method. The study found that when the E-FGR ratio was increased from 0 to 25%, the standard deviation of wall temperature decreased from 30.3 °C to 23.3 °C, and the non-uniformity coefficient decreased from 0.2598 to 0.2183, indicating an improvement in temperature uniformity. However, the thermal efficiency decreased from 82.1% to 76.2%. Moreover, at higher E-FGR ratios, the volume of the high-temperature region (above 1500 ℃) gradually decreased, and both the maximum flame temperature and the outlet NOx concentration decreased sharply. Regression equations for the E-FGR ratio (β) on the maximum combustion temperature (Tmax) and the outlet NOx concentration (CNOx) were obtained, and an E-FGR ratio greater than 13.4% was recommended to meet the emission requirements.

On the Reliability of Temperature Measurements in Natural Gas Pipelines

Accuracy of temperature measurement of natural gas flows in closed conduits is a highly debated topic due to the complexity of the measurement chain and the related economic impact. First, specific thermo-fluid dynamic issues occur because of the difference between the temperature of the gas stream and that of the external ambient and the mean radiant temperature inside the pipe. Furthermore, the installation conditions of the temperature sensor (e.g., immersion length and diameter of the thermowell) play a crucial role. In this paper, the authors present the results of a numerical and experimental study conducted both in the laboratory and in-field aimed at analyzing the reliability of temperature measurement in natural gas networks as a function of the pipe temperature and of the pressure and velocity of the gas stream. The results obtained in the laboratory show errors ranging between 0.16 and 5.87 °C in the summer regime and between -0.11 and -2.72 °C in the winter regime, depending on the external pipe temperature and gas velocity. These errors have been found to be consistent with those measured in-field, where high correlation between the pipe temperatures, the gas stream and the external ambient have been also demonstrated, especially in summer conditions.

Effect of the sputtering gas temperature on the properties of indium tin oxide films

An external gas heating device is established, and a heat treatment technology of indium tin oxide (ITO) films prepared via sputtering gas (Argon) heating is developed. Six ITO films are prepared via magnetron sputtering at room temperature, 200 °C, 300 °C, 400 °C, 500 °C, and 600 °C using an external muffle furnace heating Ar. The effects of the Ar temperature on the structure, optical, and electrical properties of the ITO films are studied. It is found that with increasing sputtering gas temperature, the sputtering rate increases gradually, and the thickness of the ITO film increases slightly during the same sputtering time. For the same film thickness, the ITO films prepared at a higher sputtering gas temperature have better photoelectric performance. With increasing Ar temperature, the surface structure of ITO film becomes gradually dense.The crystallite sizes remain relatively uniform, the resistivity is gradually reduced, and the transmittance is gradually increased. The resistivity of the ITO films with the best performance in this experiment is 2.45 × 10−4 Ω·cm, and the average transmittance between 300 and 800 nm is 90.62%. The results indicate that the heat treatment process of the ITO films prepared via Ar heating is a convenient method, which can achieve uniform heating and simultaneous heating and vacuuming. Thus, it can significantly improve the production efficiency.

Modeling and experimental investigation for development of Combined Electrolysis and Catalytic Exchange process for hydrogen isotope separation

A process based on the Combined Electrolysis and Catalytic Exchange (CECE) has been developed for separation of hydrogen isotopes. Indigenously developed Platinum supported on Carbon Aerogel based hydrophobic catalyst was used for hydrogen-water isotope exchange reaction combined with hydrophilic packing in a catalytic exchange column. The exchange column has been studied in detail for various operating conditions in this study. The intrinsic kinetics for the catalytic reaction was determined through spinning basket reactor experiments, and activation energy was estimated to be 29.7 kJ/mol. The overall mass transfer co-efficient in a mixture of hydrophilic packing and hydrophobic catalyst packed bed was determined experimentally in a pilot scale counter current trickle bed reactor to be in the range of 0.15–0.25 s-1 for the proposed range of operating conditions. Individual mass transfer resistances for vapour-liquid mass transfer, external gas mass transfer and gas-solid mass transfer were estimated using widely accepted empirical correlations. Under benchmark operating conditions, the Damkohler number for the exchange column was found to be between 0.10 and 0.16, indicating a significant contribution of surface reaction to overall mass transfer resistance. The vapour liquid mass transfer was found to be fast compared to the gas-vapour reaction. Therefore, increasing hydrophobic catalyst proportion relative to hydrophilic packing was found to increase the overall mass transfer. A steady state process model has been developed to predict the performance of overall exchange process using the experimentally determined parameters. Validation of the process model was carried out using the experimental data generated on the pilot scale trickle bed reactor. Optimum operating conditions of temperature, hydrophobic catalyst to hydrophilic packing ratio, gas and liquid superficial velocities were determined.

Ionization Air Purifying Lattice Prototype

Environmental pollution caused by human activities, the harmful mixture of gases (CO, CO2, NO2, SO2, PM), resulting from industrial production processes and vehicular traffic is a global environmental health problem in urban and rural areas; it affects vulnerable groups, children and older adults, affecting respiratory, cardiovascular and cancerous diseases. In Ecuador, in the city of Cuenca, among the main sources of contamination is the vehicle fleet in high-traffic areas and avenues; in addition to the industrial zone, that coexists with the city within the urban area in the northwest zone, which generates contamination to properties located around these strips. This paper presents the development of a purifying element based on the “evolutionary development” model. It begins by analyzing and studying concepts of lattices, ionization, and air purification, among others; subsequently, existing air purification systems are investigated in detail and a prototype of an ionizing lattice is generated, whose function is to filter polluted air when installed as an aesthetic part in buildings. Finally, the purification performance of gases and particles typical of the electrostatic precipitator (ESP) was tested by means of air quality stations. By means of a type of correlational applied research, the similarity between external and internal gases and particulate matter was verified, obtaining, as a result, the effective reduction of the same; decreasing by 4.15% of CO2, 30% of CO and 57% of particulate matter. With this analysis, it is concluded that the prototype of the ionization air purifying lattice can be efficient with some of the gases against particulate pollution in domestic interiors, positively influencing the health of the inhabitants of a building.

Gas Flow Shaping via Novel Modular Nozzle System (MoNoS) Augments kINPen-Mediated Toxicity and Immunogenicity in Tumor Organoids.

Medical gas plasma is an experimental technology for anticancer therapy. Here, partial gas ionization yielded reactive oxygen and nitrogen species, placing the technique at the heart of applied redox biomedicine. Especially with the gas plasma jet kINPen, anti-tumor efficacy was demonstrated. This study aimed to examine the potential of using passive flow shaping to enhance the medical benefits of atmospheric plasma jets (APPJ). We used an in-house developed, proprietary Modular Nozzle System (MoNoS; patent-pending) to modify the flow properties of a kINPen. MoNoS increased the nominal plasma jet-derived reactive species deposition area and stabilized the air-plasma ratio within the active plasma zone while shielding it from external flow disturbances or gas impurities. At modest flow rates, dynamic pressure reduction (DPR) adapters did not augment reactive species deposition in liquids or tumor cell killing. However, MoNoS operated at kINPen standard argon fluxes significantly improved cancer organoid growth reduction and increased tumor immunogenicity, as seen by elevated calreticulin and heat-shock protein expression, along with a significantly spurred cytokine secretion profile. Moreover, the safe application of MoNoS gas plasma jet adapters was confirmed by their similar-to-superior safety profiles assessed in the hen's egg chorioallantoic membrane (HET-CAM) coagulation and scar formation irritation assay.

Effect of External Magnetic Field on the Forming, Microstructure and Property of TC4 Titanium Alloy during the Directed Energy Deposition Arc Additive Manufacturing

In this work, the thin wall components of TC4 titanium alloy were produced by using external magnetic field hybrid gas metal welding (EM-GMAW). The effect of the external magnetic field on the forming, microstructure, and property of wire arc additively manufactured TC4 titanium alloy was studied in detail. The results showed that the height of the average deposition layer of EM-GMAW was less than that of GMAW and decreased with the increase of magnetic excitation current, and the width of the average deposition layer of EM-GMAW was greater than that of GMAW. The microstructure of the deposition layer consisted of fine α phase and coarse β grains. Compared with the traditional GMAW, the coarse β grain size in the EM-GMAW was reduced obviously. The maximum size of β grain was decreased by 100μm when the magnetic excitation current of 3A was used. In addition, the EM-GMAW tensile strength in the transverse and horizontal was increased by around 20 MPa and 100 MPa, respectively, compared with that of GMAW.