Vapor Layer Research Articles

Dual-Source Evaporation Processed Novel NaBiS2 Absorber Material for Eco-Friendly and Stable Photovoltaics.

Exploring and developing novel, low-cost, and environmentally friendly photovoltaic materials is a vital trend in the evolution of solar cell technology. The distinctive properties of alkali bismuth ternary sulfides have spurred increased research and application in optoelectronic devices. In this study, a novel method is reported for preparing NaBiS2 film by sequential thermal evaporation of Na2S and Bi2S3 layers followed by heating post-treatment for the first time, as well as the preparation of solar cells with NaBiS2 as the light-absorbing layer. Based on X-ray diffraction and Raman analysis, the prepared NaBiS2 film is confirmed to be a single-phase material, without the presence of any secondary phases. Additionally, the photoelectric characteristics of NaBiS2 are investigated and incorporated this material into solar cell devices. By optimizing the device architecture, the solar cell utilizing NaBiS2 as the light-absorbing layer achieved a photoelectric conversion efficiency of 2.91%, which is the highest efficiency reported for NaBiS2 solar cells up to now. The research has provided a valuable perspective and path for the development of novel photovoltaic materials in the solar cell field.

Solar Evaporator with Dual Gradient Heating Effect for Sustained and Efficient Desalination.

Solar desalination shows promise in tackling freshwater shortages, but challenges arise from the trade-off between water transportation and heat supply, affecting evaporators' efficiency and salt resistance. Additionally, intermittent nature of solar radiation significantly diminishes overall evaporative performance. This study presents dual-gradient heating solar evaporator for efficient desalination. Dual-gradient heating is enabled through wettability difference (hydrophilicity aerogel and hydrophobicity film) and difference in phase transition temperature of phase change material, thus, effective heat supply can be provided to evaporation layer consisting of vertically oriented phase-change aerogel by surrounding heating layer consisting of phase-change film, with and without solar radiation. Employing this design, evaporator demonstrates industry-leading comprehensive performance in practical use. Under one sun illumination, evaporation rate achieves 6.84 kgm-2h-1 in 5.0 wt% salinity, with efficiency of 90.9%. In darkness, evaporation rate remains high at 2.61 kgm-2h-1 (30 minutes). Moreover, evaporator exhibits outstanding solar energy storage capacity and long-term stabe evaporative performance and salt resistance for 7-day testing. Furthermore, evaporator successfully produces freshwater from real Bohai Sea water under weak outdoor lighting, addressing recommended daily intake of water for 2.5 households. This work introduces new perspective for maximizing utilization of solar energy for seawater desalination and overcoming intermittent solar radiation.

Thin Film Electrocatalysts on Extended Surface Supports for the Oxygen Reduction Reaction

The world is urgently looking to increase the amount of renewable energy power generation and reduce carbon emissions. Proton exchange membrane water electrolyzers (PEMWE) and fuel cells (PEMFC) play important roles in energy storage and help leveling the renewable power generation. Platinum group metals (PGMs) are popular catalysts used in PEMWE and PEMFC. However, the cost of PGMs hinders the widespread adoption of these two devices and slows down the progress of decarbonizing industrial sectors. In this talk, the oxygen reduction reaction (ORR) performance of platinum (Pt) catalysts, fabricated via different thin film deposition technologies will be compared to Pt catalysts prepared via traditional incipient wetness impregnation (IWI). Pt catalysts fabricated via thin film deposition technology, such as e-beam evaporation, sputtering, and atomic layer deposition (ALD), demonstrate higher mass activity and electrochemical surface area (ECSA) compared to Pt catalysts fabricated using IWI. This result points out the possible option to make PEMFC and PEMWE more affordable and provides alternate methods for researchers to finely control the loading of the Pt in device electrodes.

Interaction of liquid titanium with zirconates and titanates of some alkaline earth metals

Abstract The article presents the results of a study of the interaction of titanium melt with of zirconates BaZrO3 and SrZrO3, as well as titanate SrTiO3 under vacuum conditions and in an inert atmosphere at normal pressure. An original titanium heating method was used during the experiments. It eliminated the melt circulation at the interface between the solid and liquid phases. The method was based on resistive electrical heating of a Grade 2 titanium alloy rod or strip pressed into BaZrO3, SrZrO3 and SrTiO3 powders. Studied the structure, elemental, and phase composition of the products formed during various (up to 300 s) contact of titanium melt with surface zirconates and titaniums. The phase composition was compared with the products obtained by heating compacts from a mixture of titanium powders with BaZrO3, SrZrO3 and SrTiO3 powders. It was shown based on the results obtained that titanium, upon contact with these ceramic materials dissolves zirconium and oxygen and reduces barium and strontium to a metallic state. Barium and strontium evaporated due to the high vapor pressure at the experimental temperature, and caused the melt to splash or form a vapor layer that reduced the interaction rate of the melt with the ceramic. When a titanium melt interacted with BaZrO3 and SrZrO3 intermediate phases were not formed in quantities sufficient for their identification. The Sr3Zr2O7 phase was formed in small quantities during heating a mixture of Ti+SrZrO3 powders. When a titanium melt interacted with SrTiO3, a layer of an intermediate phase was formed, similar in composition to TiO2. Equations for the chemical reaction of the interaction of titanium with the indicated zirconates and titanate were compiled based on the experimental data obtained. It has been shown that titanium melt weted the surface of BaZrO3, SrZrO3 powders well and poorly weted the surface of SrTiO3 powder.

Numerical simulation of an externally heated fixed bed reactor for coal pyrolysis based on porous media

A cutting-edge three-dimensional transient model utilizing porous media has been developed to accurately simulate the pyrolysis process of externally heated coal. This innovative model comprehensively considers the evaporation and condensation of water, as well as the release of volatiles. In addition, it meticulously examines the change in coal seam porosity and the interphase heat transfer between pyrolysis gas and solid coal seam. The model's precision has been appropriately confirmed through validation against the central temperature evolution inside the experimental reactor. Notably, this model systematically illustrates various aspects, including the evolution of coal layer temperature, evaporation and moisture density, changes in coal layer density, porosity distribution, volatile release, and interphase heat transfer. The obtained results reveal that the heat absorption by moisture phase change causes the coal seam temperature to relatively stabilize at around the water boiling point for a period, thus delaying the initiation of the coal pyrolysis reaction. The pyrolysis gas released by center coal seam pyrolysis tends to flow radially toward the heating wall before flowing out of the reactor. Additionally, the change in coal seam porosity increases the heat transfer rate by an average of 1.5 °C/min during the rapid heating stage. The analysis also highlights the significant occurrence of interphase heat transfer throughout the pyrolysis process and elucidates its mechanism in various stages. Ultimately, this work offers essential theoretical guidance for the design, optimization, and scaling of subsequent externally heated fixed-bed coal pyrolysis reactors.

Nanofiber aerogel with layered array with structure coupled photothermal/magnetothermal effect for continuous seawater desalination

The solar evaporation is susceptible to intermittent solar irradiation as well as salt crystallization deposition on the surface severely limits the evaporation efficiency. In this work, subject to inspiration of the transpiration, groove array structure and antifouling performance of banana leaves, a multifunctional photothermal/ magnetothermal coupled three-dimensional(3D) aerogel evaporator with layer-by-layer array structure was prepared by blow-spun technology which can achieve mass produced. The unique super hydrophilic vertical array structure has multi-scale high-efficiency water transport channels and the SnSe-Fe3O4 evaporation layer realizes super hydrophobic self-cleaning and excellent photothermal and magnetothermal conversion performance, which can achieve all-weather seawater desalination. The vertical array structures facilitate the reflection and refraction of light and promote the seawater convection and salt crystals absorption coupling. It could improve the photothermal conversion efficiency and salt resistance of the evaporator. Which resulted in an evaporation rate of 2.53 kg m−2h−1 under 1 sun, with solar energy conversion efficiency of 105 % and the evaporation rate is about 4.54 kg m−2h−1 at a magnetic field. Furthermore, it could purify organic pollutants in industrial wastewater and use waste heat to generate electricity. This evaporator provides a new economical and environmentally friendly solution for seawater desalination and sewage treatment.

Achieving highly interfacial evaporation rate and continuous salt resistance simultaneously via multi-dimensional composite biomimetic evaporator

In response to the global freshwater crisis, various measures have been proposed. Solar-driven interfacial photoevaporation is gaining attention because its environmentally friendly and energy-efficient. However, challenges such as low solar-thermal conversion efficiency and low evaporation rates continue to hinder the advancement of solar photoevaporation technology. Inspired by Tamarisk, we proposed a multistage reflective structure using a hydrothermal method, increasing the carbon cloth (CC) surface area. Numerical simulations indicate that the plasmon resonance effect of the composites could effectively enhance the light absorption properties of the structures. Subsequently, a polyvinyl alcohol-phytic acid (PVA-PA) hydrogel was integrated with the composites to achieve effective separation of the evaporation layer from the water transport layer, thereby minimizing the interfacial light evaporation material. The PVA-PA/MnO2@CC evaporation system demonstrates excellent thermal management performance. Both experimental and simulation results confirm that the system can localize the heat obtained from photothermal conversion at the water–air interface. Additionally, the Marangoni effect, induced by the temperature gradient in the evaporation system, facilitates the transport of water in the PVA-PA hydrogel to the interface through microscopic holes. The evaporator exhibited an evaporation rate of 3.190 kg m-2h−1 in deionized water, with an evaporation efficiency of 94.1 %. Even under high-concentration brine conditions, the evaporation rate remained high, and during continuous evaporation in high-concentration brine, the surface showed no significant salt accumulation. In summary, this work combines two-dimensional carbon cloth with three-dimensional hydrogel, and incorporates metal oxides onto the carbon cloth surface to further enhance its light-trapping ability. By synthesizing the advantages of both materials, the performance of the evaporator is significantly improved.

Construction of bilayer cellulose-based aerogel with salt-resistant design for efficient solar desalination and wastewater purification

Solar-driven interfacial evaporation (SDIE) technology, which utilizes green and renewable solar energy to produce clean water, has shown great potential in alleviating global water scarcity. However, practical applications still face numerous challenges, including salt crystallization precipitation and accumulation, low energy utilization, and complex preparation processes. Hence, We designed a vertically ordered porous bilayer aerogel based on nanofibrillated cellulose (NFC)/polyethyleneimine (PEI) with excellent salt resistance, light absorption and local thermal effects to achieve efficient solar steam generation. Specifically, the photothermal conversion layer (PCL) at the top had excellent light absorption and photothermal conversion efficiency by introducing graphene oxide (GO) as a highly efficient photothermal material. The water transport layer (WTL) at the bottom ensured a stable water supply to the evaporation layer by virtue of the vertical water transfer path and inherent hydrophilicity, and effectively prevented formation of salts in the evaporation area. In addition, the designed aerogel had a low thermal conductivity, which achieved effective thermal insulation and further enhanced the localized heating effect. This superhydrophilic bilayer aerogel achieved a high evaporation rate of 1.9596 kg m−2 h−1 and an energy conversion efficiency of 92.28% under one solar irradiation. It is noteworthy that evaporation process exhibited excellent stability during 8 h of continuous evaporation in 20 wt% brine and no salt accumulation was observed on the evaporated surface. In addition, the bilayer aerogel demonstrated excellent long-term stability and self-cleaning. Meanwhile, its excellent anti-contamination and wastewater treatment capabilities give SDIE technology a stable and continuous operation in practical applications, thus demonstrating significant application potential.

Low defect density in MoS2 monolayers grown on Au(111) by metal-organic chemical vapor deposition

Monolayers of transition metal dichalcogenides (TMDs) possess high potential for applications in novel electronic and optoelectronic devices and therefore the development of methods for their scalable growth is of high importance. Among different suggested approaches, metal-organic chemical vapor deposition (MOCVD) is the most promising one for technological applications because of its lower growth temperature compared to the most other methods, e.g., conventional chemical vapor or atomic layer deposition (CVD, ALD). Here we demonstrate for the first time the epitaxial growth of MoS2 monolayers on Au(111) by MOCVD at 450 °C. We confirm the high quality of the grown TMD monolayers down to the atomic scale using several complementary methods. These include Raman spectroscopy, non-contact atomic force microscopy (nc-AFM), X-ray photoelectron spectroscopy and scanning tunneling microscopy (STM). The topographic corrugation of the MoS2 monolayer on Au(111), revealed in a moiré structure, was measured as ≈20 pm by nc-AFM. The estimated defect density calculated from STM images of the as-grown MoS2 monolayers is in the order of 1012 vacancies/cm2. The defects are mainly caused by single sulfur vacancies. Our approach is a step forward towards the technologically relevant growth of high-quality, large-area TMD monolayers.

Ignition process of the plasma scalpel in normal saline: Numerical simulation and comparison to experiment

In this paper, the ignition process of the plasma scalpel is characterized by means of numerical simulation, shadowgraphy, and voltage–current measurements. The ignition process involves two phases: the pre-breakdown phase and the breakdown phase. Our study shows that in the pre-breakdown phase, the vapor layer is first generated around the corners of the active electrode and then gradually extends to cover the entire active electrode. Once the active electrode is fully covered by the vapor layer, the electric field reaches a maximum of 7.3 × 106 V m−1, which can cause discharge in the vapor layer. At this moment, the thickness of the vapor layer is approximately 100 μm. In the breakdown phase, the maximum electron density reaches 1018–1019 m−3. The plasma dissipates about 60% of the total power which is up to 125 W, thus enabling efficient cutting. In addition, we simulate the discharge characteristics of cutting various biological tissues. The results show that under the same voltage level, the higher the conductivity of biological tissues, the greater the discharge current. The biological tissues act as ballast resistors in equivalent circuits.

Droplet temperature measurement using a fiber Bragg grating

The need to measure droplets temperature with high precision in moderate or extreme environments has driven the development of advanced methods. Here, we report, for the first time, the measurement of droplet temperature using optical fiber-based temperature sensors. Specifically, a fiber Bragg grating sensor was used as a non-invasive technique to determine the temperature behavior of single micro-volumetric pendant droplets. The fiber sensor method, which provides indirect measurements, was validated by experimental and simulation data from the literature, showing good agreement. The temperature measurements rely on monitoring the vapor layer temperature near the droplet at sub-millimeter fiber-to-droplet distances and on determining a coefficient that characterizes the temperature difference between the droplet and the surrounding vapor layer at the liquid–gas interface. We calibrated the method by conducting measurements under various relative humidities and fiber-droplet contact conditions. We found that the coefficient remains constant for a specific distance regardless of the relative humidity or the droplet volume. Furthermore, we observed the minor influences that the environmental relative humidity and droplet content has on the behavior of the recorded temperatures during the short period after droplet generation.

Controlled Crystal Growth of All-Inorganic CsPbI2Br via Sequential Vacuum Deposition for Efficient Perovskite Solar Cells.

Vacuum deposition of perovskites is a promising method for scale-up fabrication and uniform film growth. However, improvements in the photovoltaic performance of perovskites are limited by the fabrication of perovskite films, which are not optimized for high device efficiency in the vacuum evaporation process. Herein, we fabricate CsPbI2Br perovskite with high crystallinity and larger grain size by controlling the deposition sequence between PbI2 and CsBr. The nucleation barrier for perovskite formation is significantly lowered by first evaporating CsBr and then PbI2 (CsBr-PbI2), followed by the sequential evaporation of multiple layers. The results show that the reduced Gibbs free energy of CsBr-PbI2, compared with that of PbI2-CsBr, accelerates perovskite formation, resulting in larger grain size and reduced defect density. Furthermore, surface-modified homojunction perovskites are fabricated to efficiently extract charge carriers and enhance the efficiency of perovskite solar cells (PeSCs) by modulating the final PbI2 thickness before thermal annealing. Using these strategies, the best PeSC exhibits a power conversion efficiency of 13.41% for a small area (0.135 cm2), the highest value among sequential thermal deposition inorganic PeSCs, and 11.10% for a large area PeSC (1 cm2). This study presents an effective way to understand the crystal growth of thermally deposited perovskites and improve their performance in optoelectronic devices.

Leidenfrost spheres, projectiles, and model boats: Assessing the drag reduction by superhydrophobic surfaces

Superhydrophobic surfaces are expected to reduce drag on bluff bodies moving in water due to the introduction of a thin air layer around the solid and the resulting partial slip boundary condition. The use of Leidenfrost vapor layers, sustained on the surface of a heated metal body is a reliable method to estimate the maximum drag reduction possible due to such air layers. In the past such an approach was used to estimate the drag reduction on a free-falling heated sphere, in which case the form drag is the lead component of the drag force. Here, we extend this approach to evaluate the effect of the thin gas layers on the hydrodynamic drag of free-falling streamlined projectiles and towed model boats, where the form drag is minimal, and the skin friction drag is the lead component of the drag force. By comparing the drag for streamlined bodies with and without sustained air-layers, we see only incremental drag reductions, for the sub-critical Reynolds number tested herein. The same is true for towed model boats. These results hold both for superhydrophobic surface treatments and Leidenfrost vapor layers. Thus, we concluded that for the investigated range of sub-critical Reynolds numbers, the skin friction drag is less sensitive to the effect of the thin gas layers compared to the form drag. These novel findings have important implications for the practical potential of energy savings using gas layers sustained on superhydrophobic surfaces.

An experimental study on low-temperature plasma tissue ablation and its thermal effect

Low-temperature plasma ablation has been recently used for minimally invasive surgeries. However, more research is still needed on its generation process during tissue ablation and the underlying mechanism of tissue thermal damage. In this paper, high-speed camera footage, voltage–current signal collection, temperature analysis, and histological analysis were used to investigate the dynamic process of plasma tissue ablation and its thermal effect of dual-needle electrodes immersed in normal saline, which were driven by a high-frequency DC power supply with an output voltage ranging from 220 V to 320 V and a squire wave of 100 kHz. Microbubbles occurred around the ground electrode and merged to form a vapor layer that could completely cover the ground electrode. Plasma capable of ablating tissue would occur in the vapor layer between the ground electrode and tissue. The effect of electrical parameters on plasma generation and its thermal effect are analyzed by statistical results. The experimental results indicated that the voltage applied to the electrodes significantly influenced both the generation and stability of plasma, as well as the heat generation and tissue damage around the electrodes. Furthermore, under the same voltage, the existence of biological tissue promotes the formation of a vapor layer around the electrode, thereby facilitating the generation and stability of plasma. Notably, the temperature rise around the ground electrode is much higher than that around the powered electrode. These results have direct application to the design of plasma tissue ablation systems, which could achieve tissue ablation effects with minimal thermal damage.

Electrothermal-assisted all-weather solar steam generator based on hydrogel implantation strategy

Using solar energy to treat sewage is a feasible scheme to alleviate the shortage of water resources and reduce carbon emissions. However, the fluctuation of sunlight intensity poses a great challenge to the stability of the treatment process, which hinders its application in the actual water treatment scene. Herein, based on the adhesion of hydrogel, an electrothermal-assisted all-weather solar steam generator with sandwich structure was synthesized through hydrogel implantation strategy, in which polyacrylamide hydrogel with thermal grease-modified heating wires was implanted as the middle heat conduction layer, the photothermal evaporation layer as the upper layer and the waste heat evaporation layer as the bottom layer. The electrothermal assisted solar evaporator (EASE) perfectly achieves the superposition of photothermal and electrothermal effects, and can achieve high interfacial water evaporation performance under extremely low auxiliary working voltage. Applying a low voltage of 2 V to both ends of the evaporator can achieve a high evaporation rate of 4.58 kg m−2h−1 under 1 solar irradiation, which is similar to the sum of the evaporation rate under only 1 solar illumination (2.22 kg m−2h−1) and a 2 V voltage input (2.26 kg m−2h−1). More interestingly, the suitable thickness of the hydrogel layer not only ensures the transfer of heat between layers, but also weakens the heat loss caused by the water flow effect. The implantation strategy ensures the stability of the water structure and inhibits the hydrogen reaction of electrolytic water in the electrothermal process. This work provides an important theoretical and practical reference for the preparation of all-weather solar interface water purification equipment.

Self-organized composite morphologies and interface instability of immiscible alloy thin films during physical vapor deposition: Insights from phase-field simulations

In this paper, we carried out phase-field simulations for investigating self-organized composite morphologies formation and interface instability of two phase immiscible binary alloy thin-film growth during physical vapor deposition. Predicted results show that for lower the deposition rate the solid-gas interface keeps planar and the lateral composition modulation (LCM) configuration occurs. As the deposition rate increases, the self-organized composite morphology gradually transfers to vertical composition modulations (VCM) configuration and the random composition modulations (RCM) configuration with the decrease of the boundary layer of the incident vapor and the unsteady solid-gas interface. Results show that the nanoprecipitate concentration modulation (NCPM) depends strongly on the nominally phase fraction. Moreover, we found that the historical dependence of self-organized composite morphologies and solid-gas interface stability, i.e., the initial condition can strongly influence the microstructure of the thin film during physical vapor deposition. Finally, we provide an analysis method for interface instability based on fast Fourier transform (FFT), and the frequency characteristics of cellular and bump structures are identified.

Calculation of Thermal Currents in a Tungsten Plate and in a Thin Layer of Tungsten Vapor during Pulse Heating with Allowance for Temperature- and Phase-Dependent Electrical Resistance and Thermo EMF

Calculation of Thermal Currents in a Tungsten Plate and in a Thin Layer of Tungsten Vapor during Pulse Heating with Allowance for Temperature- and Phase-Dependent Electrical Resistance and Thermo EMF

A molecular dynamics study of thin water layer boiling on a plate with mixed wettability and nonlinearly increasing wall temperature

This paper introduces a molecular dynamics investigation of the influence of mixed-wettability on the boiling of a water layer over a flat plate surface with nonlinearly increasing wall temperature. The first-type Dirichlet temperature condition, which is considered for the first time in the analysis of the wettability influence on nucleation and boiling at the atomic scale, is consistent with the case of irradiation from photons, plasma, or high-temperature gas molecules. The simulation of the density evolution of water molecules in the nucleation zone shows that the surface with an optimal proportion (60 %∼70 %) of hydrophilic walls is most efficient for nucleation on the studied mixed-wettability substrates, attributing to the increased surface potential energy on the walls. Compared to the hydrophilic or hydrophobic surfaces, the mixed-wettability surfaces transfer more energy from the wall to the liquid. This is because the hydrophobic portion retards the forming of vapor layer and the hydrophilic portion induces an efficient liquid/solid interaction, with a lowered interfacial heat resistance and promoted nucleation. The results also indicate that there exists an appropriate area ratio that is most advantageous for nucleation and boiling intensification under such temperature-increasing boundary conditions. Based on this work, it may be possible to successfully manage boiling at the nanoscale by exploiting the coupled effects of hybrid wettability and irradiation.

A non-invasive capacitive sensor to investigate the Leidenfrost phenomenon: a proof of concept study

A volatile sessile liquid droplet or a sublimating solid manifests levitation on its own vapor when placed on a sufficiently heated surface, illustrating the Leidenfrost phenomenon. In this study, we introduce a non-invasive capacitance method for investigating this phenomenon, offering a potentially simpler alternative to existing optical techniques. The designed sensor features in-plane miniaturized electrodes forming a double-comb structure, also known as an interdigitated capacitor. Initially, the sensor’s capacitance is characterized for various distances between the sensor and a dielectric material. The influence of the sensor substrate material and the spacing between the electrodes on the sensor’s capacitance is also investigated. To demonstrate the feasibility of the method, a sublimating dry ice pellet is placed on the capacitive sensor, and its performance is evaluated. We present results for the dimensionless vapor layer thickness and the pellet’s lifetime at different substrate temperatures, derived from the capacitance output. The results are compared with Optical Coherence Tomography (OCT) data, serving as a benchmark. While the temporal evolution of the sensor’s output, variation in the dimensionless vapor layer thickness, and the lifetime of the dry ice pellet align with expected results from OCT, notable quantitative deviations are observed. These deviations are attributed to practical experimental limitations rather than shortcoming in the sensor’s working principle. Although this necessitates further investigation, the methodology presented in this paper can potentially serve as an alternative for the detection and measurement of Leidenfrost vapor layers.

A multistage assembled laminar membrane for solar thermal conversion and nighttime electricity production

Interfacial solar-driven evaporation technology has great potential to address freshwater shortages. Despite significant progress in developing efficient evaporators, the challenge of evaporation rates of two-dimensional evaporators still needs to be solved. In addition, interfacial solar-driven evaporation relies on solar energy to trigger the evaporation of thin water layers at the water–air interfaces. It thus may be at risk of interruption in the absence of sunlight. To overcome these challenges, we have intelligently assembled different functional components to form a multistage assembled laminar membrane used for interfacial solar-driven evaporation during the day and power generation at night. Specifically, solar evaporation achieved a high evaporation rate of 1.78 kg m−2h−1 under single solar irradiation. Desalination and water purification capabilities were also demonstrated. More notably, the membrane also showed its worth as an electrical generator in overcast weather or nights, delivering a voltage of 309 mV and a current of 2 μA. The voltage and current can be multiplied by connecting four membranes in series and parallel to 1.1 V and 8.8 μA, respectively. This powers a calculator directly and stores excess electricity in a capacitor, which can be as high as 2 V in 2000 s. This innovation shows promising applications in next-generation freshwater production and power generation.