Eutectic Gallium Indium Research Articles

Bubble Printing of Liquid Metal Colloidal Particles for Conductive Patterns.

Bubble printing is a patterning method in which particles are accumulated by the convection of bubbles generated by laser focusing. It is attracting attention as a method that enables the high-speed, high-precision patterning of various micro/nanoparticles. Although the bubble printing method is used for metallic particles and organic particles, most reports have focused on the patterning of solid particles and not on the patterning of liquid particles. In this study, liquid metal wiring patterns were fabricated using a bubble printing method in which eutectic gallium‒indium alloy (EGaIn) colloidal particles (≈diameter 0.7 µm) were fixed on a glass substrate by generating microbubbles through heat generation by focusing a femtosecond laser beam on the EGaIn colloidal particles. The wiring was then made conductive by replacing gallium oxide, which served as a resistance layer on the surface of the EGaIn colloidal particles, with silver via galvanic replacement. Fine continuous lines of liquid metal colloids with a line width of 3.4 µm were drawn by reducing the laser power. Liquid metal wiring with a conductivity of ≈1.5 × 105 S/m was formed on a glass substrate. It was confirmed that the conductivity remained consistent even when the glass substrate was bent to a curvature of 0.02 m-1.

An Antiferroelectric‐Coated Metal Foam Infiltrated with Liquid Metal as a Dielectric Capacitor

Nickel metal foams serve as both a substrate and bottom electrode for a dielectric capacitor using atomic‐layer deposition (ALD) and a eutectic gallium–indium (EGaIn) liquid metal (LQM) counter electrode. The conformal dielectric has a composition of 6.25% Al–HfO2 in the antiferroelectric phase, confirmed with polarization versus electric field measurements. Liquid EGaIn is pressure‐infiltrated within the coated foams to form the dielectric capacitor. Capacitances up to 4 μF are realized. Calorimetry of the infiltrated capacitor shows a 60 J g−1 latent heat upon melting a frozen EGaIn electrode, suggesting that the phase change can alleviate thermal deviations from pulsed power capacitor operation. Infiltrated capacitors are also shown to survive bending and freeze–thaw cycles. The metal foam–ALD dielectric–LQM capacitor shows a combined set of thermal and electrical properties not available in other classes of capacitors.

Deterministic Fabrication of Liquid Metal Nanopatterns for Nanophotonics Applications

AbstractGallium‐based liquid metals (LMs) are widely used for stretchable and reconfigurable electronics thanks to their fluidic nature and excellent conductivity. These LMs possess attractive optical properties for photonics applications as well. However, due to the high surface tension of the LMs, it is challenging to form LM nanostructures with arbitrary shapes using conventional nanofabrication techniques. As a result, LM‐based nanophotonics has not been extensively explored. Here, a simple yet effective technique is demonstrated to deterministically fabricate LM nanopatterns with high yield over a large area. This technique demonstrates for the first time the capability to fabricate LM nanophotonic structures of various precisely defined shapes and sizes using two different LMs, that is, liquid gallium and liquid eutectic gallium–indium alloy. High‐density arrays of LM nanopatterns with critical feature sizes down to ≈100 nm and inter‐pattern spacings down to ≈100 nm are achieved, corresponding to the highest resolution of any LM fabrication technique developed to date. Additionally, the LM nanopatterns demonstrate excellent long‐term stability under ambient conditions. This work paves the way toward further development of a wide range of LM nanophotonics technologies and applications.

Oxidation-Induced Oxide Shell Rupture and Phase Separation in Eutectic Gallium-Indium Nanoparticles.

Eutectic gallium-indium (EGaIn), a room-temperature liquid metal, has garnered significant attention for its applications in soft electronics, multifunctional materials, energy engineering and drug delivery. A key factor influencing these diverse applications is the spontaneous formation of a native passivating oxide shell that not only encapsulates the liquid metal but also alters the properties from the bulk counterpart. Using environmental scanning transmission electron microscopy, we report in situ observations of the oxidation of EGaIn nanoparticles by ambient air under high-energy electron beam irradiation. Our findings demonstrate that uneven oxide shell growth, driven by inward diffusion of adsorbed O species, creates unbalanced stresses. This compels the liquid metal to deform toward regions with slower oxide growth, resulting in shell rupture and allowing the liquid metal core to flow out. This process initiates top-down self-similar replication of the core-shell liquid metal nanoparticles, causing larger particles to break down into smaller particles. Additionally, internal oxidation triggers phase separation within the liquid core, ultimately leading to the pulverization of the liquid metal into finer solid particles rich in indium. These mechanistic insights into the oxidation behavior of the liquid metal hold practical implications for leveraging this process to reconfigure EGaIn nanoparticles for various applications.

Fast Responsive and High-Strain Electro-Ionic Soft Actuator Based on the 3D-Structure MXene-EGaIn/MXene Bilayer Composite Electrode.

Electro-ionic soft actuators have garnered significant attention owing to their promising applications in flexible electronics, wearable devices, and soft robotics. However, achieving high actuation performance (large bending strain and fast response time) of these soft actuators under low voltage has been challenging due to issues related to ion diffusion and accumulation. In this study, an electro-ionic soft actuator is fabricated using Ti3C2Tx MXene and eutectic gallium-indium (EGaIn) composite material as the bilayer electrode and methylammonium formate/1-ethyl-3-methylimidazolium tetrafluoroborate/poly(vinylidene fluoride) (MAF-EMIMBF4/PVDF) as the ionic liquid-type electrolyte. The research results indicate that the prepared soft actuator exhibits excellent actuation performance with a peak-to-peak displacement of 35 mm and a bending strain of 0.69% (a peak-to-peak strain of 1.38%) under a low voltage (3 V). The electro-ionic soft actuator shows a wide frequency range (0.1-10 Hz), fast response time (0.35 s), and a rise time of 7.5 s. Furthermore, it demonstrates good cyclic durability, with a retention rate of 92.5% of its performance for 10 000 cycles. These excellent performances are attributed to the 3D structure of the Ti3C2Tx-EGaIn/Ti3C2Tx bilayer composite electrode, as well as the characteristics of the low viscosity, high conductivity, small ion volume, and larger volume difference between cations and anions in MAF ionic liquid. The high-performance electro-ionic soft actuator can be used in various fields such as artificial muscles, tactile devices, and soft robots.

Microchannel pressure sensor for continuous and real-time wearable gait monitoring

A highly sensitive and multi-functional pressure sensor capable of continuous pressure readings is greatly needed, particularly for precise gait pattern analysis. Here, we fabricate a sensitive and reliable pressure sensor by employing eutectic gallium indium (EGaIn) liquid metal as the sensing material and EcoFlex 00-30 silicone as the substrate, via a low-cost process. The device architecture features a microchannel, creating two independent sensing devices, and the mechanical properties of the substrate and sensing material contribute to high stretchability and flexibility, resulting in a sensitivity of 66.07 MPa−1 and a low measurement resolution of 0.056 kPa. The sensor detects applied pressure accurately and can distinguish pressure distribution across a wide area. We demonstrate high efficiency for monitoring human walking gait at various speeds when a single sensor is attached to the foot, and can differentiate between walking postures. This device has strong potential for clinical and rehabilitation applications in gait analysis.

EGaIn-Modified ePADs for Simultaneous Detection of Homocysteine and C-Reactive Protein in Saliva toward Early Diagnosis of Cardiovascular Disease.

Homocysteine (Hcy) and C-reactive protein (CRP) are critical biomarkers for numerous chronic diseases, with cardiovascular disease (CVD) being the most prevalent. The ability to simultaneously detect both biomarkers in point-of-care settings is in high demand for CVD early diagnosis and prevention. Herein, we prepared the eutectic gallium indium (EGaIn) nanoparticles decorated with p-phenylenediamine (PPD) on the surface to facilitate the subsequent attachment of gold nanoparticles (AuNPs) to achieve EGaIn-PPD@Au, which was modified on the screen-printed electrochemical paper-based analytical devices (ePADs). Aptamers that are specific to Hcy and CRP were then immobilized on the EGaIn-PPD@Au surface to achieve the sensing interface on ePADs. The presence of EGaIn-PPD@Au significantly enhanced the electrical conductivity, leading to amplified electrochemical signals. This aptasensor demonstrated high specificity, capable of detecting Hcy in a range of 1-50 μM with a detection limit of 0.22 μM, and the detection range for CRP was 1-100 ng/mL with a detection limit of 0.039 ng/mL. The aptasensor also effectively detected Hcy and CRP in clinical saliva samples, yielding an area under the curve (AUC) of about 0.80 when the individual biomarker was considered and 0.93 when both biomarkers were taken into account. The positive correlation observed between salivary and blood concentrations of Hcy and CRP, coupled with their association with cardiovascular disease (CVD), suggested the potential of this methodology as a noninvasive point-of-care strategy for the early diagnosis of CVD.

The coalescence and oscillation of eutectic gallium indium alloy droplets

Gallium-based liquid metal droplets have excellent deformation performance, and their oscillation has huge potential in oscillator and organ-on-chip research. At present, the oscillation of gallium-based liquid metal droplets controlled by external energy (such as the application of electric fields and chemical reactions) has been thoroughly studied, while there are vacancies in the study of the oscillation due to coalescence of droplets without external energy input. A numerical simulation study on the oscillation process after the coalescence of two and three eutectic gallium indium alloy droplets is conducted. The degree of deformation of the droplet is described by the dimensionless length change in the symmetry axis direction of the line connecting the centers of the initial droplets in the top view, that is, in the y direction. The oscillation curve of the droplet is obtained by the fitting method. The results show that the oscillation of coalesced droplets has obvious periodicity and damping attenuation characteristics, and increasing the number of droplets or reducing the droplet radius will increase the damping coefficient. Furthermore, the ratio of droplet sizes and their initial distribution have an impact on the variations in kinetic energy of the three droplets in the y direction, thereby influencing the deformation of the droplets. This research enriches the theory of gallium-based liquid metal droplet deformation and plays a significant role in guiding the application of droplet oscillation in the fields of micromixers and measuring the physical parameters of solutions.

Highly flexible liquid metal/photocurable polymer electrodes via direct laser patterning

A highly flexible electrode was fabricated using eutectic gallium-indium (eGaIn) liquid metal combined with an ultraviolet (UV)-curable polyurethane acrylate (PUA) polymer. The eGaIn liquid metal electrodes prepared by a negative-type direct patterning technique using a UV pulse laser can eliminate the need for complex photolithography masks. The optimal UV pulsed laser peak fluence was ∼1.43 J/cm2 to pattern and sinter the eGaIn/PUA composite electrode simultaneously. The laser-patterned eGaIn/PUA composite electrode under the optimal laser condition exhibited a remarkable electrical conductivity of 6.33 × 105 S/m with a patterning resolution of ∼40 μm. Moreover, the resistance of the electrode only deteriorated by 0.95% after 50,000 cycles of severe cyclic folding at a peak strain of 2.5% with a bending radius of 1 mm, demonstrating its exceptional flexibility and durability. These easily patterned eGaIn flexible electrodes via direct laser patterning techniques hold great promise for applications in wearable and flexible electronic devices that require extreme flexibility.

Versatile Patterning of Liquid Metal via Multiphase 3D Printing.

This paper presents a scalable and straightforward technique for the immediate patterning of liquid metal/polymer composites via multiphase 3D printing. Capitalizing on the polymer's capacity to confine liquid metal (LM) into diverse patterns. The interplay between distinctive fluidic properties of liquid metal and its self-passivating oxide layer within an oxidative environment ensures a resilient interface with the polymer matrix. This study introduces an inventive approach for achieving versatile patterns in eutectic gallium indium (EGaIn), a gallium alloy. The efficacy of pattern formation hinges on nozzle's design and internal geometry, which govern multiphase interaction. The interplay between EGaIn and polymer within the nozzle channels, regulated by variables such as traverse speed and material flow pressure, leads to periodic patterns. These patterns, when encapsulated within a dielectric polymer polyvinyl alcohol (PVA), exhibit an augmented inherent capacitance in capacitor assemblies. This discovery not only unveils the potential for cost-effective and highly sensitive capacitive pressure sensors but also underscores prospective applications of these novel patterns in precise motion detection, including heart rate monitoring, and comprehensive analysis of gait profiles. The amalgamation of advanced materials and intricate patterning techniques presents a transformative prospect in the domains of wearable sensing and comprehensive human motion analysis.

The Promising Potential of Gallium Based Liquid Metals for Energy Storage.

Energy storage devices play a crucial role in various applications, such as powering electronics, power backup for homes and businesses, and support for the integration of renewable energy sources into electrical grid applications. Electrode materials for energy storage devices are preferred to have a flexible nature, conductive, better capacity, and low-toxicity. Using Gallium based liquid metal alloys, such as Eutectic Gallium-Indium (EGaIn), Eutectic Gallium-Tin (EGaSn), and Eutectic Gallium-Indium-Tin (EGaInSn), as electrode materials play very important role in energy storage devices. These liquid metals have some interesting properties with a self-healing nature, high mechanical stability, compatibility with various materials, fluidity, low young's modulus, high electrical and thermal conductivity. Those properties have made it suitable to be used in various energy storage devices. In this mini review, we have concisely described the advantages and challenges of using liquid metal as electrode materials for various energy storage devices.

Liquid metal nanoparticles as photo-initiators for preparation of transparent hydrogel with adjustable mechanical properties

To achieve rapid preparation of hydrogels without using conventional chemical initiators, a stable suspension of eutectic gallium indium (EGaIn) liquid metal nanoparticles is explored by probe-sonicating the metal in an aqueous solution. Liquid metal suspension was sonicated to serve as a photo-initiator for acrylamide polymerization and produce hydrogels. The initiation effect comes from the fact that liquid metal suspension after sonication can produce a large number of free radicals when exposed to ultraviolet (UV) radiation, leading to initiation. The changes of liquid metal nanodroplets under UV light irradiation have been systematically investigated. Further, the liquid metal colloidal solutions were used to prepare hydrogels with the same transparency and adjustable mechanical properties as the samples initiated by commercial photo-initiators. This work shows the great application potential of liquid metal in the preparation of hydrogels and provides a new technical idea for the design of multifunctional hydrogels.

Thiol Coordination Softens Liquid Metal Particles To Improve On-Demand Conductivity.

Achieving tunable rupturing of eutectic gallium indium (EGaIn) particles holds great significance in flexible electronic applications, particularly pressure sensors. We tune the mechanosensitivity of EGaIn particles by preparing them in toluene with thiol surfactants and demonstrate an improvement over typical preparations in ethanol. We observe, across multiple length scales, that thiol surfactants and the nonpolar solvent synergistically reduce the applied stress requirements for electromechanical actuation. At the nanoscale, dodecanethiol and propanethiol in toluene suppress gallium oxide growth, as characterized by transmission electron microscopy and X-ray photoelectron spectroscopy. Quantitative AFM imaging produces force-indentation curves and height images, while conductive AFM measures current while probing individual EGaIn particles. As the applied force increases, thiolated particles demonstrate intensified softening, rupturing, and stress-induced electrical activation at forces 40% lower than those for bare particles in ethanol. To confirm that thiolation facilitates rupturing at the macroscale, a laser is used to ablate samples of EGaIn particles. Scanning electron microscopy and resistance measurements across macroscopic samples confirm that thiolated EGaIn particles coalesce to exhibit electrical activation at 0.1 W. Particles prepared in ethanol, however, require 3 times higher laser power to demonstrate a similar behavior. This unique collection of advanced techniques demonstrates that our particle synthesis conditions can facilitate on-demand functionality to benefit electronic applications.

Development of eutectic gallium-indium-based transparent conductive electrodes on flexible substrates for touch sensor integration

In this study, the adaptability of liquid metal (LM)-based transparent conductive electrodes (TCEs) to flexible substrates and their potential applications in various electronics fields were investigated. To achieve this, conventional microfabrication techniques were employed to pattern polydimethylsiloxane (PDMS) channels and introduce an Eutectic Gallium-Indium (EGaIn) LM with the aim of enhancing transmittance and reducing sheet resistance. Microfluidic channel structures with varying pitch lengths and widths were fabricated in the types of grid patterns, labeled Pattern A (2000 μm pitch, 40 μm width), Pattern B (2000 μm pitch, 80 μm width), Pattern C (200 μm pitch, 40 μm width), and Pattern D (200 μm pitch, 80 μm width. The corresponding average transmittance values for the EGaIn LM-based TCE were 90 %, 71.8 %, 61.8 %, and 43.2 % for Patterns A, B, C, and D, respectively. To illustrate the potential in touch sensor applications, resistance changes in Patterns A, B, C, and D were assessed under applied forces ranging from 0 N to 150 N, revealing resistance changes of 0.0265 Ω, 0.03617 Ω, 0.03977 Ω, and 0.11629 Ω, respectively.

Multifunctional asymmetric foam with Compression-Enhanced EMI shielding effectiveness exhibits Real-Time tunability of Reflection/Absorption ratio and pressure sensing

Traditional electromagnetic interference (EMI) shielding materials usually have constant shielding effectiveness and fixed absorption/reflection ratio, and cannot respond to the real-time changing shielding requirements of smart wearable electronic devices. Herein, smart asymmetric foams (AF) composed of chromium dioxide decorated graphene (CrO2@G)/thermoplastic polyurethane-poly vinyl alcohol (TP) foams and a eutectic gallium-indium liquid metal (LM)/TP layer were developed via an efficient ‘split conductive modular design/assembly’ strategy. The AF with compressive stress-controlled conductivity can capture and attenuate electromagnetic (EM) waves in the form of absorption-dominated or reflection-dominated by adjusting the compressive strain in real time. The optimized AF achieved a low average reflection coefficient (R) of 0.12 and a minimum value of 0.05, holding the lowest record for LM-based EMI shielding materials with comparable SEt. As the compressive strain increases from 0 to 90 %, the AF alter its SEt from 63.8 ± 3 dB to 92.7 ± 2 dB, while reducing the average EM wave absorption efficiency from 88 % to 39 %, allowing it to be adjusted in real time as needed to block EM waves. Furthermore, the AF demonstrated its application as a strain sensor to monitor human motions. This work provides an effective strategy for the design and preparation of multifunctional smart EMI shielding materials.

Injectable composite hydrogels embedded with gallium-based liquid metal particles for solid breast cancer treatment via chemo-photothermal combination

Photothermal therapy (PTT) holds great promise as a cancer treatment modality by generating localized heat at the tumor site. Among various photothermal agents, gallium-based liquid metal (LM) has been widely used as a new photothermal-inducible metallic compound due to its structural transformability. To overcome limitations of random aggregation and dissipation of administrated LM particles into a human body, we developed LM-containing injectable composite hydrogel platforms capable of achieving spatiotemporal PTT and chemotherapy. Eutectic gallium–indium LM particles were first stabilized with 1,2-Distearoyl-sn‑glycero-3-phosphoethanolamine (DSPE) lipids. They were then incorporated into an interpenetrating hydrogel network composed of thiolated gelatin conjugated with 6-mercaptopurine (MP) chemodrug and poly(ethylene glycol)-diacrylate. The resulted composite hydrogel exhibited sufficient capability to induce MDA-MB-231 breast cancer cell death through a multi-step mechanism: (1) hyperthermic cancer cell death due to temperature elevation by near-infrared laser irradiation via LM particles, (2) leakage of glutathione (GSH) and cleavage of disulfide bonds due to destruction of cancer cells. As a consequence, additional chemotherapy was facilitated by GSH, leading to accelerated release of MP within the tumor microenvironment. The effectiveness of our composite hydrogel system was evaluated both in vitro and in vivo, demonstrating significant tumor suppression and killing. These results demonstrate the potential of this injectable composite hydrogel for spatiotemporal cancer treatment. In conclusion, integration of PTT and chemotherapy within our hydrogel platform offers enhanced therapeutic efficacy, suggesting promising prospects for future clinical applications. Statement of significanceOur research pioneers a breakthrough in cancer treatments by developing an injectable hydrogel platform incorporating liquid metal (LM) particle-mediated photothermal therapy and 6-mercaptopurine (MP)-based chemotherapy. The combination of gallium-based LM and MP achieves synergistic anticancer effects, and our injectable composite hydrogel acts as a localized reservoir for specific delivery of both therapeutic agents. This platform induces a multi-step anticancer mechanism, combining NIR-mediated hyperthermic tumor death and drug release triggered by released glutathione from damaged cancer populations. The synergistic efficacy validated in vitro and in vivo studies highlights significant tumor suppression. This injectable composite hydrogel with synergistic therapeutic efficacy holds immense promise for biomaterial-mediated spatiotemporal treatment of solid tumors, offering a potent targeted therapy for triple negative breast cancers.

Stabilizing Solid Electrolyte Interphase on Liquid Metal Via Dynamic Hydrogel-Derived Carbon Framework Encapsulation.

Eutectic gallium-indium liquid metal (EGaIn-LM), with a considerable capacity and unique self-healing properties derived from its intrinsic liquid nature, gains tremendous attention for lithium-ion batteries (LIBs) anode. However, the fluidity of the LM can trigger continuous consumption of the electrolyte, and its liquid-solid transition during the lithiation/de-lithiation process may result in the rupture of the solid electrolyte interface (SEI). Herein, LM is employed as an initiator to in situ assemble the 3D hydrogel for dynamically encapsulating itself; the LM nanoparticles can be homogeneously confined within the hydrogel-derived carbon framework (HDC) after calcination. Such design effectively alleviates the volume expansion of LM and facilitates electron transportation, resulting in a superior rate capability and long-term cyclability. Further, the "dual-layer" SEI structure and its key components, including the robust LiF outer layer and corrosion-resistant and ionic conductive LiGaOx inner layer are revealed, confirming the involvement of LM in the formation of SEI, as well as the important role of carbon framework in reducing interfacial side reactions and SEI decomposition. This work provides a distinct perspective for the formation, structural evolution, and composition of SEI at the liquid/solid interface, and demonstrates an effective strategy to construct a reliable matrix for stabilizing the SEI.

A Novel PDMS-Based Flexible Thermoelectric Generator Fabricated by Ag2Se and PEDOT:PSS/Multi-Walled Carbon Nanotubes with High Output Performance Optimized by Embedded Eutectic Gallium-Indium Electrodes.

Flexible thermoelectric generators (FTEGs), which can overcome the energy supply limitations of wearable devices, have received considerable attention. However, the use of toxic Te-based materials and fracture-prone electrodes constrains the application of FTEGs. In this study, a novel Ag2Se and Poly (3,4-ethylene dioxythiophene): poly (styrene sulfonate) (PEDOT:PSS)/multi-walled carbon nanotube (MWCNT) FTEG with a high output performance and good flexibility is developed. The thermoelectric columns formulated in the work are environmentally friendly and reliable. The key enabler of this work is the use of embedded EGaIn electrodes, which increase the temperature difference collected by the thermoelectric column, thereby improving the FTEG output performance. Additionally, the embedded EGaIn electrodes could be directly printed on polydimethylsiloxane (PDMS) molds without wax paper, which simplifies the preparation process of FTEGs and enhances the fabrication efficiency. The FTEG with embedded electrodes exhibits the highest output power density of 25.83 μW/cm2 and the highest output power of 10.95 μW at ΔT = 15 K. The latter is 31.6% higher than that of silver-based FTEGs and 2.5% higher than that of covered EGaIn-based FTEGs. Moreover, the prepared FTEG has an excellent flexibility (>1500 bends) and output power stability (>30 days). At high humidity and high temperature, the prepared FTEG maintains good performance. These results demonstrate that the prepared FTEGs can be used as a stable and environmentally friendly energy supply for wearable devices.

Deformable micro-supercapacitor fabricated via laser ablation patterning of Graphene/liquid metal

Deformable and miniaturized energy storage devices are essential for powering soft electronics. Herein, we fabricate deformable micro supercapacitors (MSCs) based on eutectic gallium-indium liquid metal (EGaIn) current collectors with integrated graphene. The well-define interdigitated electrode patterning with controlled gap is successfully realized by using the laser ablation because of a strong laser absorption of graphene and EGaIn. By judicious control of gap size between neighboring interdigitated electrodes and mass loading of graphene, we achieve a high areal capacitance (1336 µF cm−2) with reliable rate performance. In addition, owing to the intrinsic liquid characteristics of EGaIn current collector, the areal capacitance of fabricated MSC retains 90% of original value even after repetitive folding and 20% stretching up to 1000 cycles. Finally, we successfully integrate deformable MSC with a commercial light-emitting diode to demonstrate the feasibility of MSC as a deformable power source. The fabricated MSCs operate stably under various mechanical deformations, including stretching, folding, twisting, and wrinkling.

Regenerated silk fibroin coating stable liquid metal nanoparticles enhance photothermal antimicrobial activity of hydrogel for wound infection repair

The integration of liquid metal (LM) and regenerated silk fibroin (RSF) hydrogel holds great potential for achieving effective antibacterial wound treatment through the LM photothermal effect. However, the challenge of LM's uncontrollable shape-deformability hinders its stable application. To address this, we propose a straightforward and environmentally-friendly ice-bath ultrasonic treatment method to fabricate stable RSF-coated eutectic gallium indium (EGaIn) nanoparticles (RSF@EGaIn NPs). Additionally, a double-crosslinked hydrogel (RSF-P-EGaIn) is prepared by incorporating poly N-isopropyl acrylamide (PNIPAAm) and RSF@EGaIn NPs, leading to improved mechanical properties and temperature sensitivity. Our findings reveal that RSF@EGaIn NPs exhibit excellent stability, and the use of near-infrared (NIR) irradiation enhances the antibacterial behavior of RSF-P-EGaIn hydrogel in vivo. In fact, in vivo testing demonstrates that wounds treated with RSF-P-EGaIn hydrogel under NIR irradiation completely healed within 14 days post-trauma infection, with the formation of new skin and hair. Histological examination further indicates that RSF-P-EGaIn hydrogel promoted epithelialization and well-organized collagen deposition in the dermis. These promising results lay a solid foundation for the future development of drug release systems based on photothermal-responsive hydrogels utilizing RSF-P-EGaIn.