End-column Amperometric Detection Research Articles

Microchip capillary electrophoresis with a boron-doped diamond electrochemical detector for analysis of aromatic amines.

The attractive features of a boron-doped diamond (BDD) thin-film detector for microchip capillary electrophoretic (CE) separations of dye-related amino-substituted aromatic compounds are described. The diamond electrode was employed in the end-column amperometric detection of 4-aminophenol (4-AP), 1,2-phenylenediamine (1,2-PDA), 2-aminonaphthalene (2-AN), 2-chloroaniline (2-CA), and o-aminobenzoic acid (o-ABA), and its attractive behavior was compared to commonly used screen-printed carbon and glassy-carbon electrodes. These conventional electrode materials exhibit a significant degree of passivation and low sensitivity to the above-mentioned environmental pollutants. The diamond-based electrochemical detection system displayed a favorable analytical performance, including lower noise levels, higher peak resolution with enhanced sensitivity, and improved resistance against electrode passivation. Factors influencing the on-chip analysis were assessed and optimized. The diamond detector displayed detection limits of 2.0 and 1.3 microM for 4-AP and 2-AN, respectively, and a wide linear response for these compounds over the 2-50 microM range. The enhanced stability was demonstrated by relative standard deviation (RSD) values of 1.4% and 4.7% for 100 microM 1,2-PDA and 200 microM 2-CA, respectively, for repetitive detections (n = 7). Besides, the simultaneously observed current decrease was 2.4 and 9.1% for 1,2-PDA and 2-CA, respectively (compared to 21.8 and 41.0% at the screen-printed carbon electrode and 28.3 and 34.1% at the glassy carbon electrode, respectively). The favorable properties of the diamond electrode indicate great promise for environmental applications in CE and other microchip devices.

Study of urinary 8-hydroxydeoxyguanosine as a biomarker of oxidative DNA damage in diabetic nephropathy patients

Increased oxidative stress induced by hyperglycemia may contribute to the pathogenesis of diabetic complications. Urinary 8-hydroxydeoxyguanosine (8-OHdG) has been reported to serve as a sensitive biomarker of oxidative DNA damage and also of oxidative stress. This article studied oxidative DNA damage in patients with diabetic nephropathy and in healthy control subjects by urinary 8-OHdG evaluations. Contents of 8-OHdG in urine were analyzed by capillary electrophoresis with end-column amperometric detection (CE-AD) after a single-step solid-phase extraction (SPE). Levels of urinary 8-OHdG in diabetic nephropathy patients with macroalbuminuria was significant higher than in control subjects (5.72±6.89 μmol/mol creatinine versus 2.33±2.83 μmol/mol creatinine, P = 0.018). A significant difference of 24 h urinary 8-OHdG excretions exists between the patients with macroalbuminuria and the patients with normoalbuminuria (19.2±16.8 μg/24 h versus 8.1±1.7 μg/24 h, P = 0.015). There was a positive correlation between urinary excretion of 8-OHdG and glycosylated hemoglobin (HbA 1c) ( r = 0.287, P = 0.022). A weak correlation exists between the levels of 8-OHdG and triglyceride ( r = 0.230, P = 0.074). However, the urinary 8-OHdG contents are not correlated with blood pressure and total cholesterol. The increased excretion of urinary 8-OHdG is seen as indicating an increased systemic level of oxidative DNA damage in diabetic nephropathy patients.

Fabrication of poly(methyl methacrylate) microfluidic chips by atmospheric molding.

A greatly simplified method for fabricating poly(methyl methacrylate) (PMMA) separation microchips is introduced. The new protocol relies on UV-initiated polymerization of the monomer solution in an open mold under ambient pressure. Silicon microstructures are transferred to the polymer substrate by molding a methyl methacrylate solution in a sandwich (silicon master/Teflon spacer/glass plate) mold. The chips are subsequently assembled by thermal sealing of the channel and cover plates. The new fabrication method obviates the need for specialized replication equipment and reduces the complexity of prototyping and manufacturing. Variables of the fabrication process were assessed and optimized. The new method compares favorably with common fabrication techniques, yielding high-quality devices with well-defined channel and injection-cross structures, and highly smoothed surfaces. Nearly 100 PMMA chips were replicated using a single silicon master, with high chip-to-chip reproducibility (relative standard deviations of 1.5 and 4.7% for the widths and depths of the replicated channels, respectively). The relatively high EOF value of the new chips (2.12 x 10(-4) cm(2) x V(-1) x s(-1)) indicates that the UV polymerization process increases the surface charge and hence enhances the fluidic transport. The attractive performance of the new CE microchips has been demonstrated in connection with end-column amperometric and contactless-conductivity detection schemes. While the new approach is demonstrated in connection with PMMA microchips, it could be applied to other materials that undergo light-initiated polymerization. The new approach brings significant simplification of the process of fabricating PMMA devices and should lead to a widespread low-cost production of high-quality separation microchips.

Capillary zone electrophoresis with pre-column NDA derivatization and amperometric detection for the analysis of four aliphatic diamines

A method was developed for the analysis of four aliphatic diamines by capillary zone electrophoresis using pre-column derivatization with naphthalene-2,3-dicarboxaldehyde (NDA)/CN − and amperometric detection. The pre-column derivatization reaction conditions including the molar ratio of NDA to amines, the cyanide concentration, the pH value of derivatization buffer, and the reaction time, were investigated. The separation of four derivatives of aliphatic diamines has been optimized by capillary zone electrophoresis (CZE) using end-column amperometric detection with a carbon fiber microelectrode, at a constant potential of 0.7 V versus SCE. The optimum conditions for the separation were 10 mM Tris–H 3PO 4 (pH 4.0) for the running buffer solution, 15 kV for the separation voltage. The detection limits for diaminopropane, putrescine, cadaverine, diaminohexane were 6.7×10 −8, 5.1×10 −8, 1.9×10 −7 and 3.8×10 −7 M, respectively (S/N=3). The proposed method was applied to the determination of aliphatic diamines in a lake water sample by the standard addition method. The recovery of these amines in water was 89.9–107%.

Capillary electrophoresis with end-column amperometric detection of urinary 8-hydroxy-2'-deoxyguanosine.

Urinary 8-hydroxy-2'-deoxyguanosine (8OHdG) is an excellent marker of oxidative DNA damage. Until now, urinary 8OHdG has been measured by high-performance liquid chromatography with electrochemical detection. A simple and sensitive method for the analysis of urinary 8OHdG by capillary electrophoresis with end-column amperometric detection has been developed in our laboratory. A single-step solid-phase extraction procedure was optimized and used for extracting 8OHdG from human urine. To improve the sensitivity of this method, a new focusing technique based on a dynamic pH junction was used. The limit of detection was 20 nM (signal-to-noise ratio S/N = 3), the linear range was 50 nM-10 microM, and the correlation coefficient was better than 0.999. The relative standard deviation (RSD) was found to be 0.57% for migration time, and 4.79% for peak current. To show the usefulness of the method, the urinary concentration of 8OHdG in nine healthy persons and ten cancer patients was determined. The urinary concentration of 8OHdG in cancer patients was significantly higher than that in healthy persons.

Etched electrochemical detection for electrophoresis in nanometer inner diameter capillaries.

Capillary electrophoresis in nanometer inner diameter capillaries allows for the analysis of extremely small volume samples, such as the contents of single cells. However, the utilization of these ultrasmall capillaries requires a very sensitive and low volume detector. An improved method for end-column amperometric detection for capillary electrophoresis in nanometer inner diameter (i.d.) capillaries is presented. This new method involves etching both the electrode and the detection end of the capillary. These design improvements allow for better alignment between the capillary bore and the electrode. As a result, dead volume in the detector is minimized. The etched method for electrochemical detection in ultrasmall capillaries provides average coulometric efficiencies of 70 +/- 10% for dopamine and 40 +/- 20% for catechol in 770 nm i.d. capillaries. Furthermore, this technique provides peak efficiencies as high as 100,000 theoretical plates and detection limits as low as 340 zmol for both dopamine and catechol.

Microchip capillary electrophoresis coupled with a boron-doped diamond electrode-based electrochemical detector.

The attractive behavior and advantages of a diamond electrode detector for a micromachined capillary electrophoresis (CE) system are discussed. A chemically vapor-deposited boron-doped diamond (BDD) film band (0.3 x 6.0 mm) electrode is used for end-column amperomettic detection. The favorable performance of the diamond electrode microchip detector is indicated from comparison to a commonly used thick-film carbon detector. The diamond electrode offers enhanced sensitivity, lower noise levels, and sharper peaks for several groups of important anaytes (nitroaromatic explosives, organophosphate nerve agents, phenols). The favorable signal-to-background characteristics of the BDD-based CE detector are coupled with a greatly improved resistance to surface fouling and greater isolation from high separation voltages. The enhanced stability is indicated from a RSD of 0.8% for 60 repetitive measurements of 5 ppm 2,4,6-trinitrotoluene (vs RSD of 10.8% at the thick-film carbon electrode). A highly linear response is obtained for the explosives 1,3-dinitrobenzene and 2,4-dinitrotoluene over the 200-1,400 ppb range, with detection limits of 70 and 110 ppb, respectively. Factors influencing the performance of the BDD detector are assessed and optimized. The attractive properties of BDD make it very promising material for electrochemical detection in CE microchip systems and other micromachined flow analyzers.

Deviceless decoupled electrochemical detection of catecholamines in capillary electrophoresis using gold microband array electrodes.

Samples containing microM concentrations of dopamine, (+/-)-isoproterenol, para-aminophenol and chlorogenic acid have been separated by capillary electrophoresis (CE) and detected using end-column amperometric detection based on a novel decoupling method. The present decoupling approach involves the use of an electrochemical detector chip containing an array of microband electrodes where the working and reference electrodes are positioned only 10 microm from each other. The short distance between the working and reference electrodes ensures that both electrodes are very similarly affected by the presence of the CE electric field. With this method, no shift in the detection potential was seen when the CE high voltage was applied. This eliminated the need for a reoptimization of the detection potential to compensate for the influence of the separation voltage on the detection. It is also demonstrated that catecholamines can be detected using gold microband electrodes by careful adjustment of the detection potential to avoid the formation of gold oxide. Such careful adjustments of the detection potential are straightforward using the present decoupling method.

Determination of midecamycin by capillary zone electrophoresis with electrochemical detection

Capillary zone electrophoresis was employed for the determination of midecamycin using an end-column amperometric detection with a carbon fiber micro-disk bundle electrode at a constant potential of +1.15 V vs. saturated calomel electrode. The optimum conditions of separation and detection are 1.00×10 −3 mol l −1 Na 2HPO 4–3.49×10 −4 mol l −1 NaOH (pH 11.4) for the buffer solution, 20 kV for the separation voltage, 5 kV and 5 s for the injection voltage and the injection time, respectively. The limit of detection is 5.0×10 −7 mol l −1 or 0.41 fmol ( S/N=3). The linear range of the calibration curve is 1.00×10 −6–1.00×10 −3 mol l −1. The relative standard deviation is 1.4% for the migration time and 4.9% for the electrophoretic peak current. The method could be applied to the determination of midecamycin in human urine. In this case, a separation voltage of 14 kV was used.

A dynamically modified microfluidic poly(dimethylsiloxane) chip with electrochemical detection for biological analysis.

Separation and direct detection of amino acids, glucose and peptide in a 3.1 cm separation channel made of poly(dimethylsiloxane) (PDMS) with end-column amperometric detection at a copper microdisk electrode was developed. This system is the integration of a normal sized working electrode with electrochemical detection on a PDMS microfabricated device. The PDMS channels dynamically modified by 2-morpholinoethanesulfonic acid (MES) show less adsorption and more enhanced efficiency than that of unmodified ones when applied to separations of these biological molecules. The migration time is less than 100 s and the reproducibility of migration time is satisfactory with relative standard deviation (RSD) of 2.8% in 19 successive injections. The limits of detection of arginine (Arg), glucose, and methionine-glycine (Met-Gly) are estimated to be 2.0, 8.5, and 64.0 microM at S/N = 3, approximately 0.5-16.0 fmol, respectively. Variances influencing the separation efficiency and amperometric response, including injection, separation voltage, detection potential, or concentration of buffer and additive, are assessed and optimized.

Determination of histamine by capillary zone electrophoresis with amperometric detection.

Capillary zone electrophoresis was employed for the determination of histamine using end-column amperometric detection with a carbon fiber microelectrode, at a constant potential. The optimum conditions of separation and detection were 10 mmol/L phosphate buffer, pH 5.6 for the buffer solution, 15 kV for the separation voltage, and 1.35 V (versus SCE) for the detection potential. The linear range was from 6.3 x 10(-7) to 1.5 x 1(-5) mol/L with the regression coefficient of 0.9997, and the detection limit was 4.0 x 10(-7) mol/L (S/N = 3). The proposed method was successfully applied to the direct determination of histamine in the beer samples without any sample clean-up procedures.

A dynamically modified microfluidic poly(dimethylsiloxane) chip with electrochemical detection for biological analysis

Separation and direct detection of amino acids, glucose and peptide in a 3.1 cm separation channel made of poly(dimethylsiloxane) (PDMS) with end-column amperometric detection at a copper microdisk electrode was developed. This system is the integration of a normal sized working electrode with electrochemical detection on a PDMS microfabricated device. The PDMS channels dynamically modified by 2-morpholinoethanesulfonic acid (MES) show less adsorption and more enhanced efficiency than that of unmodified ones when applied to separations of these biological molecules. The migration time is less than 100 s and the reproducibility of migration time is satisfactory with relative standard deviation (RSD) of 2.8% in 19 successive injections. The limits of detection of arginine (Arg), glucose, and methionine-glycine (Met-Gly) are estimated to be 2.0, 8.5, and 64.0 microM at S/N = 3, approximately 0.5-16.0 fmol, respectively. Variances influencing the separation efficiency and amperometric response, including injection, separation voltage, detection potential, or concentration of buffer and additive, are assessed and optimized.

Determination of thiols in urinary sample by capillary-column liquid chromatography with amperometric detection at a carbon electrode

The fabrication and application of an end-column amperometric detection (AD) system with a carbon electrode for capillary-column liquid chromatography (CLC) were described. This new amperometric detector showed good sensitivity and stability in detecting the thiocompounds and other analytes with CLC. In order to obtain the better separation and detection performance for analytes, several operational parameters had been investigated: the working potentials, pH and flow rate. Under the optimum conditions, the method could effectively separate and determine cysteine (Cys), glutathione (GSH), dopamine (DA) and 6-thiopurine (6-TP). Good repeatability for retention time was obtained with a relative standard deviation (R.S.D.) value of 0.5%. The linear range covered over three orders of magnitude and the limits of detection were 8 fmol for cysteine, 20 fmol for glutathione, 8 fmol for dopamine and 20 fmol for 6-thiopurine. This method was successfully applied in determination of urinary sample with characteristics of simplicity, high sensitivity and good repeatability.

Method of intracellular naphthalene-2,3-dicarboxaldehyde derivatization for analysis of amino acids in a single erythrocyte by capillary zone electrophoresis with electrochemical detection

A novel method of intracellular derivatization was developed. In this method, the derivatization reagents [naphthalene-2,3-dicarboxaldehyde (NDA) and CN −] were introduced into living cells by electroporation for the derivatization reaction. After completion of derivatization reaction in cells, a single cell was drawn into the capillary tip by electroosmotic flow. Then the lysing solution was introduced into the capillary by diffusion. Once the individual cell was lysed, the derivatized amino acids in the individual cell were separated by capillary zone electrophoresis and detected by end-column amperometric detection at the outlet of the capillary. This method of intracellular NDA derivatization confined the analytes and the derivatization reagents to the volume of a single cell expanded. For an 8-μm erythrocyte, the contents were diluted by a factor of only ca. 1.6. The method was used to determination of amino acids in single erythrocytes. Six amino acids were identified and quantified.

Direct amperometric determination of lactate at a carbon fiber bundle microdisk electrode by capillary zone electrophoresis

Capillary zone electrophoresis was employed for the determination of lactate using end-column amperometric detection at a carbon fiber bundle microdisk electrode. The optimum conditions of separation and detection are 3.6×10 −3 mol/l Na 2HPO 4–1.4×10 −3 mol/l NaH 2PO (pH 7.2) for the buffer solution, 18 kV for the separation voltage and 1.60 V versus the saturated calomel electrode for the detection potential. The limit of detection is 7.6×10 −7 mol/l or 1.7 fmol ( S/N=3) and the linear range is 1.7×10 −6–8.2×10 −4 mol/l for the injection voltage of 6 kV and injection time of 5 s. The RSD is 1.8% for the migration time and 3.3% for the electrophoretic peak current. The method was applied to the determination of lactate in human saliva. The recovery of the method is between 95 and 109%.

Determination of Histamine by Capillary Zone Electrophoresis with End-Column Amperometric Detection at a Carbon Fiber Microdisk Array Electrode

Capillary zone electrophoresis (CZE) was employed for the analysis of histamine using an end-column amperometric detector with a carbon fiber microdisk array electrode. The optimum conditions of separation and detection are: 40 mmol/L NaH2PO4–Na2HPO4 (pH 7.0) for the buffer solution, 12.5 kV for the separation voltage, 5 kV and 10 s for the injection voltage and the injection time, and 1.30 V (vs. SCE) for the detection potential. The limit of detection is 3.3×10−6 mol/L or 13 fmol (signal to noise, S/N=3). The relative standard derivation was 0.45% for the migration time and 3.2% for the electrophoretic peak current. The method can be applied to determining histamine in rat peritoneal mast cells. The recovery of the method is between 92 and 99%.

Determination of Histamine by Capillary Zone Electrophoresis with End-Column Amperometric Detection at a Carbon Fiber Microdisk Array Electrode

Determination of Histamine by Capillary Zone Electrophoresis with End-Column Amperometric Detection at a Carbon Fiber Microdisk Array Electrode

Determination of allopurinol and its active metabolite oxypurinol by capillary electrophoresis with end-column amperometric detection

A simple method was proposed for the separation of allopurinol (AP) and its active metabolite oxypurinol (OP) by capillary electrophoresis with end-column amperometric detection. A running buffer composed of 15 mM Na 2HPO 4/NaH 2PO 4 at a pH 9.55, electrokinetic injection 7 s at 5 kV, separation voltage at 15 kV and detection potential at 1.20 V were investigated to be the optimal condition for the separation. The method exhibited low detection limit ( S/ N=3) as 1×10 −8 mol/l for AP and OP, wide linearity range of 2×10 −7 to 1×10 −4 mol/l, 1×10 −7 to 1×10 −4 and high efficiency of 1.2×10 5 and 1.8×10 5 N/m for AP and OP, respectively. The potential application examined for the method was the determination of the spiked urine sample, which was proved to be sensitive and efficient.

Chiral separation of promethazine by capillary electrophoresis with end-column amperometric detection

Sensitive end-column amperometric detection has been successfully coupled to capillary electrophoresis for chiral separation of promethazine, with a carbon fiber microdisk electrode as working electrode. Baseline separation and sensitive detection were achieved under optimum conditions: 0.030 M Na2HPO4 and 0.015 M citric acid at pH = 2.50, 1.0 mM beta -CD, 10 kV separation voltage, and detection potential 1.10 V (vs Ag/AgCl). The numbers of theoretical plates were higher than 700000, and the detection limit was 5 x 10(-8) M. On-line treatment of the electrode has also been studied and discussed.

Chiral separation of promethazine by capillary electrophoresis with end-column amperometric detection

Chiral separation of promethazine by capillary electrophoresis with end-column amperometric detection