Emission Noise Research Articles

Simulative analysis of 1 Tb/s all-optical half-adder using quantum dot semiconductor optical amplifiers

Abstract All-optical half adder using quantum dot semiconductor optical amplifier is proposed and analyzed using numerical simulations for two different unsaturated gains. Cross gain modulation (XGM) and cross phase modulation (XPM) in Mach–Zehnder interferometer structure generate CARRY and SUM, respectively, of the half adder. The performance of the device is optimized with respect to input pump powers and effect of amplified spontaneous emission (ASE) noise is also investigated. We have found extinction ratio (ER) as high as 16.48 dB for SUM and 12.95 dB for CARRY which ensures efficient performance of the proposed half adder. The quality factor Q is also high (24.58 dB for SUM and 18.47 dB for CARRY). These confirm clear transmissions of the bits with low bit error rate (BER).

Generation of Perfectly Entangled Two and Three Qubits States by Classical Random Interaction

AbstractThis study examines the possibility of finding perfect entanglers for a Hamiltonian which corresponds to several quantum information platforms of interest at the present time. However, in this study, a superconducting circuit is used that stands out from other quantum‐computing devices, especially because transmon qubits can be coupled via capacitors or microwave cavities, which enables to combine high coherence, fast gates, and high flexibility in its design parameters. There are currently two factors limiting the performance of superconducting processors: timing mismatch and the limitation of entangling gates to two qubits. In this work, a two‐qubit SWAP and a three‐qubit Fredkin gate is presented, additionally, a perfect adiabatic entanglement generation between two and three programmable superconducting qubits is also demonstrated. Furthermore, the impact of random dephasing, emission, and absorption noises on the quantum gates and entanglement is also demonstrated in this study. It is demonstrated by numerical simulation that CSWAP gate and W‐state generation can be achieved perfectly in one step with high reliability under weak coupling conditions. Hence, this scheme could contribute to quantum teleportation, quantum communication, and some other areas of quantum information processing.

Liquid crystal based active wavelength filter for phase-sensitive optical time domain reflectometry.

This study proposes a liquid-crystal-based active wavelength filter for phase-sensitive optical time domain reflectometry to mitigate the amplified spontaneous emission (ASE) noise and accurately match the passband with the light source. The validity of the proposed system was verified using comparative experiments with conventional passive optical filters. The experiment showed an increase in signal-to-noise ratio (SNR) of up to 2.21 dB compared with passive filters. Additionally, the proposed system can effectively eliminate ASE noise, resulting in an SNR of 12.99 dB.

Free-space optical stealth communication based on wide-band spontaneous emission

We proposed and experimentally demonstrated a free-space optical stealth communication system that hides the stealth signal in wide-band spontaneous emission noise. Spontaneous emission light sources have been widely used for illuminations and has been recently deployed for short distance and indoor free-space optical communications, such as LiFi. Since free-space optical communication is a broadcasting network, the users’ privacy is exposed to eavesdropping attacks. In this paper, stealth communication is achieved by taking advantage of the existing properties of spontaneous emission light sources, random phase fluctuations, and protects users’ privacy in free-space communication networks. The keys to hide and recover the stealth signal are the optical delays at the transmitter and receiver. Only by matching the delay length with the pre-shared keys can the authorized receiver recover the stealth signal. Without the right key, the eavesdropper receives a constant power that is the same as illumination light sources and cannot detect the existence of the stealth signal.

Stimulated Brillouin Scattering Threshold in Presence of Modulation Instability for Optical Pulse in Long Optical Fiber

A theoretical and experimental study on the stimulated Brillouin scattering (SBS) threshold for optical pulse in the presence of modulation instability (MI) in long optical fiber is presented. The effects of MI on the SBS gain and threshold are analyzed based on the coupled-wave equation. An analytic expression is obtained to calculate the SBS threshold in the presence of MI. Numerical simulation is conducted to study the effects of the repetition rate and amplified spontaneous emission (ASE) noise on the SBS threshold for optical pulses. An experiment is conducted, and the results agree well with the theoretical analysis. The results clearly reveal how MI affects the Brillouin gain and SBS threshold of optical pulses in long optical fiber. The SBS threshold is affected by the ASE noise level and the repetition rate of the optical pulse. The study is helpful for the power evaluation of interferometric fiber sensing systems and optical power transmission systems.

Nonlinear Spectrum Modulation in the Anomalous Dispersion Regime Using Second- and Third-Order Solitons

We study the robustness of a nonlinear frequency-division multiplexing (NFDM) system, based on the Zakharov-Shabat spectral problem (ZSSP), that is comprised of two independent quadrature phase-shift keyed (QPSK) channels modulated in the discrete spectrum associated with two distinct eigenvalues. Among the many fiber impairments that may limit this system, we focus on determining the limits due to third-order dispersion, the Raman effect, amplified spontaneous emission (ASE) noise from erbium-doped fiber amplifiers (EDFAs), and fiber losses with lumped gain from EDFAs. We examine the impact of these impairments on a 1600-km system by analyzing the Q-factor calculated from the error vector magnitude (EVM) of the received symbols. We found that the maximum launch power due to these impairments is: 13 dBm due to third-order dispersion, 11 dBm due to the Raman effect, 3 dBm due to fiber losses with lumped gain, and 2 dBm due to these three impairments combined with ASE noise. The maximum launch power due to all these impairments combined is comparable to that of a conventional wavelength-division multiplexing (WDM) system, even though WDM systems can operate over a much larger bandwidth and, consequently, have a much higher data throughput when compared with NFDM systems. We find that fiber losses in practical fiber transmission systems with lumped gain from EDFAs is the most stringent limiting factor in the performance of this NFDM system.

All-optical latches using carrier reservoir semiconductor optical amplifiers

Lightwave communication systems, optical random memories, and photonic encryption/decryption are important applications that rely on all-optical latches. For the first time, the carrier reservoir semiconductor optical amplifiers (CR-SOAs) are employed to simulate two basic optical latches, Set-Reset (SR) latch, and D Flip-Flop, at a data rate of 120 Gb/s. All-optical NAND and NOT logic operations are used to build these latches, which are implemented using Mach-Zehnder interferometers (MZIs) with CR-SOAs. In the presence of the amplified spontaneous emission noise, the variation of the output quality factor (Q-factor) against the CR-SOA key operating parameters is studied. This is achieved by exploiting and numerically solving a set of coupled partial differential equations that describe the CR-SOAs gain and phase dynamics when operated as nonlinear elements and embedded in MZIs. The results demonstrate that CR-SOAs-based MZIs can achieve a high Q-factor while implementing the logical SR latch and D Flip-Flop at a high speed of 120 Gb/s.

Phenomenological process of rebar corrosion in reinforced concrete evaluated by acoustic emission and electrochemical noise

Rebar corrosion was evaluated by monitoring reinforced concrete specimens. An electrical corrosion test accelerated the corrosion, and non-destructive evaluation of the acoustic emission (AE) and electrochemical noise (EN) was applied. Because AE phenomena were detected during rebar corrosion, the rise time and maximum amplitude increased, showing waveform variations. The AE activity was attributed to oxide film peeling of the rebar surface. The pitting index of the EN analysis ranged from –1 to 0, indicating localized corrosion. The EN method can detect pitting corrosion on rebar surfaces. AE and EN can be combined to phenomenologically evaluate early-stage rebar corrosion in concrete.

Simple amplifier configuration algorithm for dynamic C + L-band systems in the presence of stimulated Raman scattering

We propose a simple two-step amplifier configuration algorithm based on signal power across different channels to improve the generalized signal-to-noise ratio (GSNR) performance of dynamic C + L-band links in the presence of amplifier spontaneous emission (ASE) noise, Kerr nonlinearity, and stimulated Raman scattering (SRS) using erbium-doped fiber amplifiers (EDFA). In step 1, ASE noise and Kerr nonlinearity are taken into account to derive sub-optimal signal power profiles at the beginning of each span using the local optimization global optimization (LOGO) strategy. The effect of SRS is compensated through amplifier gain pre-tilt in step 2. Simulations for links with homogeneous/heterogeneous spans, static full-channel loading, and dynamic loading due to gradual channel additions for C + L-band upgrades show that the proposed algorithm can achieve similar GSNR performance, but requires much less execution time, compared to other iterative methods that target for improving the GSNR across the C + L band, thus making it a fast and efficient GSNR management strategy for future dynamic C + L-band networks.

Optical sensor using space-domain active fiber cavity ringdown technique

A novel active fiber cavity ringdown (FCRD) technique using frequency-shifted interferometry (FSI) is proposed for the first time. Using this scheme, external parameters can be monitored in the space domain by measuring the ringdown distance instead of ringdown time. A bidirectional erbium-doped fiber amplifier (Bi-EDFA) is employed to compensate the inherent cavity loss for achieving higher sensitivity. And two band-pass filters are used to reduce the amplified spontaneous emission (ASE) noise of the Bi-EDFA. Compared with the well-known time-domain active FCRD scheme, our proposed method enables us to avoid using pulsed laser needed in time-domain active FCRD, it uses continuous-wave laser to inject into the fiber cavity and stabilize the optical power in the fiber cavity, which can suppress the baseline drift of ringdown signal caused by the gain fluctuations of the EDFA and thus improve the detecting precision. Moreover, this novel method enables us to use differential detection method for further reducing the ASE noise, and thus eliminating the baseline drift of ringdown signal. A magnetic field sensor was developed as a proof-of-concept demonstration. The experimental results demonstrate that the proposed sensor with a sensitivity of 0.01537 (1/km·Gs) was achieved. This is the highest magnetic field sensitivity compared to the time-domain active FLRD method. Due to the reduced ASE noise, the stability of the proposed sensing system was also greatly improved.

Blind nonlinearity equalization by machine-learning-based clustering for QAM-based quantum noise stream cipher transmission

In quantum noise stream cipher (QNSC) systems, it is difficult to compensate fiber nonlinearity by digital signal processing (DSP) due to interactions between chromatic dispersion (CD), amplified spontaneous emission (ASE) noise from erbium-doped fiber amplifier (EDFA) and Kerr nonlinearity. Nonlinearity equalizer (NLE) based on machine learning (ML) algorithms have been extensively studied. However, most NLE based on supervised ML algorithms have high training overhead and computation complexity. In addition, the performance of these algorithms have a lot of randomness. This paper proposes two clustering algorithms based on Fuzzy-logic C-Means Clustering (FLC) to compensate the fiber nonlinearity in quadrature amplitude modulation (QAM)-based QNSC system, including FLC based on subtractive clustering (SC) and annealing evolution (AE) algorithm. The performance of FLC-SC and FLC-AE are evaluated through simulation and experiment. The proposed algorithms can promptly obtain suitable initial centroids and choose optimal initial centroids of the clusters to achieve the global optimal initial centroids especially for high order modulation scheme. In the simulation, different parameter configurations are considered, including fiber length, optical signal-to-noise ratio (OSNR), clipping ratio and resolution of digital to analog converter (DAC). Furthermore, we measure the Q-factor of transmission signal with different launched powers, DAC resolution and laser linewidth in the optical back-to-back (BTB) experiment with 80-km single mode fiber. Both simulation and experimental results show that the proposed techniques can greatly mitigate the signal impairments.

Research on the Performance of Multimode Optical Chaotic Secure Communication System With Multidimensional Keys and a Complex Entropy Source

In this paper, we design an optical chaotic secure communication system with multi-dimensional keys and a complex entropy source, which can allow secure communication working in different modes such as unicast, multicast, and broadcast. In the proposed scheme, amplified spontaneous emission (ASE) noise of the erbium-doped fiber amplifier (EDFA) with sufficient randomness is used as an entropy source to improve the security of the system. And by using the electro-optic delay feedback loops, the key spaces are introduced and the phase distortion is generated, then the data are masked in both phase and intensity fields. As a frequency-dependent group delay (FDGD) module, Gires-Tournois interferometer (G-T I) in the feedback loop can effectively hide the time delay signature (TDS) and achieve additional 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">36</sup> key spaces. The influence of different key mismatches on decryption function is numerically investigated, and the results indicate that the broadband nature of ASE noise makes the TDS a very sensitive encryption key, which increases the difficulty of illegal third parties stealing information. And with the help of the wavelength converter and wavelength division multiplexer, secure communication in various modes is successfully realized, which greatly improves the communication efficiency and is suitable for various security places.

Data-Driven Method for Nonlinear Optical Fiber Channel Modeling Based on Deep Neural Network

Recently, data-driven fiber channel modeling methods based on deep learning have been proposed in optical communication system simulations. We investigate a new data-driven method based on the deep neural network (DNN) to model the nonlinear fiber channel with the characteristics of attenuation, chromatic dispersion, amplified spontaneous emission noise, self-phase modulation (SPM), and cross-phase modulation (XPM). Demonstration in multiple dimensions, including constellations, optical waveforms, spectra, and the normalized mean square error, shows that DNN can approach the transfer function of the fiber channel accurately. Additionally, the DNN shows good generalization for modulation formats and wavelength schemes. Besides, the time complexity of DNN-based method for modeling nonlinear fiber channel is reduced significantly (96.5%) compared to the conventional model-driven method, which is based on the split-step Fourier method. This work demonstrates that the DNN can model accurately the nonlinear fiber channel that takes account of both SPM and XPM. Therefore, it can contribute to the application of data-driven methods in modern optical communication system simulations and designs.

Design and Development of Light Motor Vehicle Exhaust System for Emission Control and Noise Reduction

Abstract: The ideal of this work is to develop a silencer that can amend dangerous exhaust discharge and noise produced in this conventional silencer. The health and hygienic policy depend upon the term air pollution. Weakened air causes physical illgoods and decides undesirable aesthetic and physiological goods. Air pollution can be defined as an inclusion to atmosphere of any material solid or gases which will have a various effect on life. The main adulterants contribute by machines are unburned hydrocarbon (UBHC), oxides of nitrogen (NOx), carbon monoxide (CO), and Lead. This research work is an attempt and contribution in this direction; it's substantially dealing with the comb of emission and noise. This system is fitted to the exhaust pipe of the machine. This type of silencer is used to reduce emission, and Noise and also reduces its dangerous goods with the help of actuated outland, lime water. As the Sound produced under lime water is less audible than it produced in the atmosphere. This is because of small sprockets which are present in water motes, which lower their breadth and lower the sound position. Hence water is used in this silencer. These silencers are used to reduce the noise and control the emissions of dangerous feasts and release much lower weakened feasts to the terrain and it's easy to install.

Impact of amplified spontaneous emission noise on the SRS threshold of high-power fiber amplifiers

Impact of amplified spontaneous emission (ASE) noise on the stimulated Raman scattering (SRS) threshold of high-power fiber amplifiers is demonstrated numerically through a spectral evolution approach. The simulation results confirm that ASE noise in the Raman wavelength band could reduce the SRS threshold of high-power fiber amplifiers significantly. As for ASE noise originated the main amplifier, it becomes stronger and reduces the SRS threshold at shorter operation wavelength below 1052 nm. As for ASE noise originated from the seed laser, it reduces the SRS threshold at different operation wavelength under the condition that the Raman ratio is over –90 dB in the seed laser. The theoretical method and results in this work could provide a well reference to extend the operation wavelength of high-power fiber lasers.

DWDM signals noise immunity evaluation in a nonlinear fiber-optic path

The total influence of self-phase modulation, phase cross-modulation and four-wave mixing effects and amplified spontaneous emission noise on transmitted pulsed signals noise immunity in a multichannel fiberoptic transmission system with spectral division multiplexing is investigated. The investigation is carried out under the conditions of transmitting system parameters variation: the total optical power level in optical fiber, the transmission speed and the number of spectral channels. The estimate criterion of transmitted pulsed signals noise immunity is Q-factor. The total Q-factor value dependence on the total optical power level in optical fiber for various transmission speed and the number of spectral channels is demonstrated.

Hardware-Efficient Blind Frequency Offset Estimation for Spectral-Efficient Digital Subcarrier Multiplexing Systems

For the digital subcarriermultiplexing (DSM) transmission, it is compulsory to realize the frequency offset estimation (FOE) and compensation (FOC) before the subcarrier de-multiplexing and the chromatic dispersion (CD) compensation (CDC). Here, we demonstrate a blind FOE method for the spectral-efficient DSM signals with a sharper root raised cosine (RRC) spectral shaping, with the capabilities of the transparent modulation format operation, a wide FOE range, and a high FOE accuracy. By reusing the spectral information for the CDC, the proposed FOE method is hardware efficient. Moreover, the proposed FOE method is numerically identified robust to transmission impairments, including the amplified spontaneous emission (ASE) noise, the optical filtering effect, and the accumulated CD, with an estimation error of less than 35 MHz under a FFT size of 2048. The correct function of the proposed FOE method is finally experimentally verified for 25 Gbaud 16QAM DSM signals under scenarios of both back-to-back (B2B) and standard single-mode fiber (SSMF) transmissions.

Mitigation of amplified spontaneous emission noise for an all-fiber coaxial aerosol lidar with different single-photon detectors

For a coaxial single-photon lidar system, amplified spontaneous emission (ASE) noise from the fiber amplifier is inevitable. The ASE backscattering from specular reflection annihilates the far-field weak signal, resulting in low signal-to-noise ratio, short measurement distance, and even misidentification. We propose a method for calibrating and mitigating ASE noise in all-fiber coaxial aerosol lidar and demonstrate the method for a lidar system with different single-photon detectors (SPDs). The accuracy of the coaxial aerosol lidar is comparable to that of the biaxial one. We conducted an experiment using three different detectors, namely, InGaAs/InP SPD, up-conversion SPD, and superconducting nanowire SPD in the same coaxial lidar system. Compared with the biaxial system, the three different detectors we used have achieved more than 90% ASE noise suppression, the measured visibility percent errors of InGaAs/InP SPD data, up-conversion SPD data, and superconducting nanowire SPD data all within 20%, and the percent error within 10% are 99.47%, 100%, and 95.12%, respectively. Moreover, time-sharing optical switching allowed to obtain background noise with high accuracy.

Self-Water-Removal and Voltage Behavior Improvement of Dead-Ended Proton Exchange Membrane Fuel Cell Stack at Steady-State and Dynamic Conditions

The proton exchange membrane fuel cell (PEMFC) demonstrates high commercial competitiveness due to its advantages: low operating temperature, high power/mass ratio, fast response, no emission, and low noise. Thermal and water management remains a challenging issue for ensuring the fuel cell’s performance at steady-state and dynamic conditions. The cathode moisture condensation uses a semiconductor cooler to effectively remove excess water from the PEMFCs and reduce the probability of flooding of the stack. The stack’s voltage uniformity is an essential factor that affects the performance and lifetime of PEMFC. This paper investigates the dynamic response characteristics of the voltage uniformity of a PEMFC stack under cathode moisture condensation conditions. The results show that the condensation temperature at 10°C during the steady-state or transient operation of the PEMFC can effectively optimize the stack’s performance. Compared to conventional PEMFC, applying the cathode moisture condensation technology to the PEMFC stack increases the stack voltage by 6% and decreases the voltage uniformity by up to 30%. This self-water-removal technology effectively improves the voltage uniformity of the stack, which then increase the stack durability.

Experimental and Theoretical Study of Plastic Deformation of Epoxy Coatings on Metal Substrates Using the Acoustic Emission Method.

Propagation of acoustic emission signals in continuous conjugated media under real-time loading was explored. The results of explored plastic deformation polymer coatings on a metal base using the acoustic emission method with synchronization of deformations and the moments of occurrence of acoustic emission signals are presented. Using the principal component method, the acoustic emission spectra, which make it possible to trace the evolution of deformation transformation processes, were analyzed. Presented the results of theoretical and experimental studies on the separate propagation of acoustic emission vibrations in a polymer coating, a metal base, and their joint combination in the form of multilayer structures. Boundary problems of propagation of acoustic emission signals in the conjugation of continuous media are considered from the standpoint of an elastic continuum and wave representations. The main variables are the force that initiates the appearance of acoustic emission signals and the displacement that determines the propagation of elastic waves. Based on the local rearrangement of the internal structure of conjugated media under conditions of development of deformation processes in the material, the verification of the main theoretical models of energy spectrum acoustic signals in continuous media at the micro-, meso-, and macro-levels was carried out. In this work, we present experimental data on a set of basic acoustic emission characteristics for four-point bending. It is shown that the principal components method reduces the dimension of data while maintaining the least amount of new information. Using the method of principal components to determine the stages of plastic deformation of polymer coatings on a metal base using the acoustic emission method. With the digitalization of acoustic emission signals and noise filtering, new possibilities for isolating a weak signal at the noise level appear even when its amplitude is significantly lower than the noise level. The study results can be used to predict the degree of destruction of two-layer materials under loading.