Electronic Devices Research Articles

Using Quality Function Deployment to Assess the Efficiency of Mini-Channel Heat Exchangers

This article addresses the design of a compact heat exchanger for the cooling of electronic systems. The Quality Function Deployment (QFD) method is used to identify crucial product features to improve device performance and key customer requirements. The QFD simplifies management processes, allowing modifications to device components, such as design parameters (dimensions and materials) and operating conditions (flow type and preferred temperature range). The study was applied to analyse the fundamental features of a compact heat exchanger, assessing their impact on enhancing heat transfer intensity during fluid flow through mini-channels. The thermal efficiency of the compact heat exchanger was tested experimentally. The results allow to verify the results obtained from the numerical simulations due to Simcenter STAR-CCM+. Consequently, the experimental part was reduced in favour of numerical simulations conducted using this commercial CFD software version 2020.2.1 Build 15.04.01. The numerical simulations performed with the aid of CFD showed increases in the heat transfer coefficient of up to 180% compared to the case treated as a reference. The application of the QFD matrix significantly reduces the time required to develop suitable design and material solutions and determine the operating parameters for the cooling of miniature electronic devices.

Comprehensive analysis on three-phase imbalance management technology of low-voltage distribution network

Energy production and use is one of the major sources of global greenhouse gas emissions. To combat climate change, many countries and organizations are pushing to reduce the use of fossil fuels, and the use of renewable energy sources such as solar, wind, and hydro is growing rapidly. The conversion of these renewable energy into electricity requires a large amount of power electronics. Power electronics have higher energy conversion efficiency, greater adjustability and control, and smaller size and weight than traditional generators. These characteristics make power electronic equipment have a wide range of application prospects in the field of energy conversion and power control. There may be cost, reliability, debugging, and three-phase imbalance issues. Based on the harm of three-phase imbalance to the economic operation and safe and stable operation of distribution network, the importance of three-phase imbalance in low-voltage distribution network is expounded, and the relationship between three-phase unbalance current and power factor is elaborated on the construction of three-phase imbalance. Reduce the harm of three-phase imbalance to the distribution network and reduce the loss of distribution network lines.

Fine-Pitch Copper Nanowire Interconnects for 2.5/3D System Integration

AbstractHeterogeneous integration is a key driver within the field of advanced electronic packaging. The realization of tomorrow’s highly integrated electronic systems depends on the combination and compatibility of various integration technologies at the same hierarchy level. The adoption of novel bonding technologies for a cost-effective realization of multi-chiplet systems is a key aspect. Cu nanowire (NW) interconnects exhibit distinct advantages in terms of their scalability down to a few micrometers, the resulting joint properties and moderate demands with respect to the surface preparation, and the cleanliness of the bonding environment. No solder or flux is required for the bonding process, but the NW bumps still can compensate low height differences. The bonding process can be carried out near room temperature under ambient conditions. We demonstrate the technological possibility to integrate the Cu-NWs for a bump processing scheme including the Cu seed etching on 300 mm wafer for the first time. This paper focuses on the microstructure evaluation and the shear test of the formed Cu-NW interconnects fabricated under ambient conditions within a few seconds. The microstructure analysis shows the intact bonded interconnects and reveals high-resolution details of Cu-NWs. The shear strength of the formed interconnects varies between 4.6 MPa and 90.5 MPa depending on the bonding and annealing conditions. Overall, the results of this study highlight the potential of Cu-NW interconnects for future 3D heterogeneous system integration.

Recent advances in single-phase rectification methods

With the increasing number of population, people are increasingly dependent on electricity. In recent years, more and more public transportations like bus, taxi take the mode of pure electric. The function of rectifier is to transform the AC current into DC current, which is a significant research direction in electrical industry, especially in power electronic technology. In our nation, the national grid supplies 220V 50Hz AC to residence, it is a voltage pattern that varies periodically. Due to the lower loss of power during long-distance transmission, it has become the basic mode of power transmission and supply in the world. In usual production and our daily life, we frequently need DC (such as: mobile phones, flashlights, computers, charging piles for electric vehicles, etc.), so rectifier has become a heated research part. At present, more and more researches are based on power electronic technology, design all kinds of rectifier circuit by using the between conductor and insulator property of semiconductors. This essay provides an overview of single-phase rectifier circuits (including half-wave rectifier, full-wave rectifier, and bridge rectifier) and passive power factor correction.

Amphibious Multifunctional Hydrogel Flexible Haptic Sensor with Self-Compensation Mechanism

In recent years, hydrogel-based wearable flexible electronic devices have attracted much attention. However, hydrogel-based sensors are affected by structural fatigue, material aging, and water absorption and swelling, making stability and accuracy a major challenge. In this study, we present a DN-SPEZ dual-network hydrogel prepared using polyvinyl alcohol (PVA), sodium alginate (SA), ethylene glycol (EG), and ZnSO4 and propose a self-calibration compensation strategy. The strategy utilizes a metal salt solution to adjust the carrier concentration of the hydrogel to mitigate the resistance drift phenomenon to improve the stability and accuracy of hydrogel sensors in amphibious scenarios, such as land and water. The ExpGrow model was used to characterize the trend of the ∆R/R0 dynamic response curves of the hydrogels in the stress tests, and the average deviation of the fitted curves ` was calculated to quantify the stability differences of different groups. The results showed that the stability of the uncompensated group was much lower than that of the compensated group utilizing LiCl, NaCl, KCl, MgCl2, and AlCl3 solutions (` in the uncompensated group in air was 276.158, 1.888, 2.971, 30.586, and 13.561 times higher than that of the compensated group in LiCl, NaCl, KCl, MgCl2, and AlCl3, respectively;` in the uncompensated group in seawater was 10.287 times, 1.008 times, 1.161 times, 4.986 times, 1.281 times, respectively, higher than that of the compensated group in LiCl, NaCl, KCl, MgCl2 and AlCl3). In addition, for the ranking of the compensation effect of different compensation solutions, the concentration of the compensation solution and the ionic radius and charge of the cation were found to be important factors in determining the compensation effect. Detection of events in amphibious environments such as swallowing, robotic arm grasping, Morse code, and finger–wrist bending was also performed in this study. This work provides a viable method for stability and accuracy enhancement of dual-network hydrogel sensors with strain and pressure sensing capabilities and offers solutions for sensor applications in both airborne and underwater amphibious environments.

Accelerating Conjugate Heat Transfer Simulations in Squared Heated Cavities through Graphics Processing Unit (GPU) Computing

This research develops an innovative framework for accelerating Conjugate Heat Transfer (CHT) simulations within squared heated cavities through the application of Graphics Processing Units (GPUs). Although leveraging GPUs for computational speed improvements is well recognized, this study distinguishes itself by formulating a tailored optimization strategy utilizing the CUDA-C programming language. This approach is specifically designed to tackle the inherent challenges of modeling squared cavity configurations in thermal simulations. Comparative performance evaluations reveal that our GPU-accelerated framework reduces computation times by up to 99.7% relative to traditional mono-core CPU processing. More importantly, it demonstrates an increase in accuracy in heat transfer predictions compared to existing CPU-based models. These results highlight not only the technical feasibility but also the substantial enhancements in simulation efficiency and accuracy, which are crucial for critical engineering applications such as aerospace component design, electronic device cooling, and energy system optimization. By advancing GPU computational techniques, this work contributes significantly to the field of thermal management, offering a potential for broader application and paving the way for more efficient, sustainable engineering solutions.

Prevalence and risk factors associated with neck pain among smartphone users at the University of Balochistan, Pakistan: a cross-sectional study

Background Shoulder and neck pain is a highly prevalent musculoskeletal disorder. Different factors have been associated with it; among these factors some common are the use of a computer and smartphones without a break, sitting in an uncomfortable position. It has been reported that the prevalence of neck pain among smartphone users ranges from 20.0%-73%. This study will evaluate the prevalence of neck pain among smartphone users and the risk factors associated with it at the University of Balochistan Quetta Pakistan. Method This cross-sectional study was conducted from September to October 2022 at the University of Balochistan Quetta to find out the prevalence of neck pain and it risk factors. Data were collected randomly by distributing 500 questionnaires among the students irrespective of age, gender, department, and year of study. Data were analyzed using SPSS Version 23. Continuous variables were presented as mean ± SD, and categorical variables as frequencies and percentages. Univariate and multivariate binary logistic regression analysis were used to find out the risk factors associated with neck pain and a p-value <0.05 was considered significant. Results The results revealed that the prevalence of neck pain was 73%. In MVBLR analysis, male gender (OR=0.360, p-value=0.000), students in 4th year (OR=3.281, p-value=0.002), Left handed (OR=0.395, p-value=0.002), the habit of physical exercise (OR=0.594, p-value=0.032), number of social media used in a day (OR=2.414, p-value=0.039), use of other electronic devices (OR=1.858, p-value=0.010), style of holding (OR=3.289, p-value=0.008) and posture adopted during smartphones use (OR=0.614, p-value=0.050) had a significant association with the neck pain during smartphone use among university students. Conclusion In the current study high number of study, participants reported neck pain. Female gender, students in 4th year, left-handed, the habit of physical exercise, use of five or more social media applications, use of other electronic devices, and posture adopted on laying back were the risk factors associated with neck pain.

Exploring the Post-Annealing Influence on Stannous Oxide Thin Films via Chemical Bath Deposition Technique: Unveiling Structural, Optical, and Electrical Dynamics

Stannous oxide (SnO2) thin films have garnered significant attention for their promising applications in various electronic and optoelectronic devices. In this study, we investigate the impact of post-annealing on the structural, optical, and electrical properties of stannous oxide thin films deposited using the chemical bath deposition (CBD) technique. The thin films were prepared on a Borosilicate glass substrate, followed by a controlled annealing process to enhance their performance. Structural analysis was conducted using techniques such as X-ray diffraction (XRD) to examine the cubic crystalline structure and the crystallite size increase induced by post-annealing. The results revealed alterations in grain size from the SEM and the purity of samples confirmed from EDX results. The optical properties of the Stannous oxide thin films were examined using UV-Vis spectroscopy. The optical absorption and bandgap characteristics were analyzed to understand how post-annealing influences the optical behavior of the thin films. Where the optical absorption was 320nm and the bandgap ranges were 3.86eV to 3.83eV. Furthermore, the electrical properties of the thin films were evaluated semiconducting nature, and conductivity increased with rising post-annealing. The findings from this study contribute to the understanding of the role of post-annealing in tailoring the properties of Stannous oxide thin films. The optimization of structural, optical, and electrical characteristics is crucial for their successful integration into electronic and optoelectronic devices.

Toxicity of two heavy rare earth elements to freshwater mussels Dreissena polymorpha.

Rare earth elements (REE) are essential components of many electronic devices that could end-up in solid waste disposal sites and inadvertently released in the environment. The purpose of this study was to examine the toxicity of two heavy REEs, erbium (Er) and lutetium (Lu), in freshwater mussels Dreissena polymorpha. Mussels were exposed to 14 days to increasing concentration (10, 50, 250, and 1250 µg/L) of either Er and Lu at 15 °C and analyzed for gene expression in catalase (CAT), superoxide dismutase (SOD), metallothionein (MT), cytochrome c oxidase (CO1), and cyclin D for cell cycle. In addition, lipid peroxidation (LPO), DNA damage (DNAd), and arachidonate cyclooxygenase were also determined. The data revealed that mussels accumulated Er and Lu similarly andboth REEs induced changes in mitochondrial COI activity. Er increased cell division, MT, and LPO, while Lu increased DNAd and decreased cell division. Tissue levels of Er were related to changes in MT (r = 0.7), LPO (r = 0.42), CO1 (r = 0.69), and CycD (r = 0.31). Lu tissue levels were related to changes in CO1 (r = 0.73), CycD (r = - 0.61), CAT (r = 0.31), DNAd (r = 0.43), and SOD (r = 0.34). Although the lethal threshold was similar between Er and Lu, the threshold response for LPO revealed that Er produced toxicity at concentrations 25 times lower than Lu suggesting that Er was more harmful than Lu in mussels. In conclusions, the data supports that the toxicity pattern differed between Er and Lu although they are accumulated in the same fashion.

Evidence for multiferroicity in single-layer CuCrSe2

Multiferroic materials, which simultaneously exhibit ferroelectricity and magnetism, have attracted substantial attention due to their fascinating physical properties and potential technological applications. With the trends towards device miniaturization, there is an increasing demand for the persistence of multiferroicity in single-layer materials at elevated temperatures. Here, we report high-temperature multiferroicity in single-layer CuCrSe2, which hosts room-temperature ferroelectricity and 120 K ferromagnetism. Notably, the ferromagnetic coupling in single-layer CuCrSe2 is enhanced by the ferroelectricity-induced orbital shift of Cr atoms, which is distinct from both types I and II multiferroicity. These findings are supported by a combination of second-harmonic generation, piezo-response force microscopy, scanning transmission electron microscopy, magnetic, and Hall measurements. Our research provides not only an exemplary platform for delving into intrinsic magnetoelectric interactions at the single-layer limit but also sheds light on potential development of electronic and spintronic devices utilizing two-dimensional multiferroics.

Intrinsically Stretchable Floating Gate Memory Transistors for Data Storage of Electronic Skin Devices.

To propel electronic skin (e-skin) to the next level by integrating artificial intelligence features with advanced sensory capabilities, it is imperative to develop stretchable memory device technology. A stretchable memory device for e-skin must offer, in particular, long-term data storage while ensuring the security of personal information under any type of deformation. However, despite the significance of these needs, technology related to stretchable memory devices remains in its infancy. Here, we report an intrinsically stretchable floating gate (FG) polymer memory transistor. The device features a dual-stimuli (optical and electrical) writing system to prevent easy erasure of recorded data. An FG comprising an intermixture of Ag nanoparticles and elastomer and with proper energy-band alignment between the semiconductor and dielectric facilitated sustainable memory performance, while achieving a high memory on/off ratio (>105) and a long retention time (106 s) with the ability to withstand 50% uniaxial or 30% biaxial strain. In addition, our memory transistor exhibited high mechanical durability over multiple stretching cycles (1000 times), along with excellent environmental stability with respect to factors such as temperature, moisture, air, and delamination. Finally, we fabricated a 7 × 7 active-matrix memory transistor array for personalized storage of e-skin data and successfully demonstrated its functionality.

Vaping Behavior and Intention to Quit among Undergraduate Students in a Hispanic-Serving University.

The surge in electronic nicotine delivery systems (ENDS) usage, particularly among young adults, poses significant public health concerns. This study aimed to identify predictors of e-cigarette use, quit attempts, and frequency among undergraduate students in a Hispanic-serving university in Texas. A cross-sectional study was conducted between August 1 and October 26, 2023, recruiting undergraduate students through the Sona system, an online experiment management platform. Participants completed an online survey that covered demographics, educational status, vaping status, initiation age, reasons for first and current e-cigarette use, frequency of past usage, intentions to quit, and quit attempt frequency. Statistical analysis included descriptive statistics, multinomial logistic regression, and multivariable linear regression. Among 316 participants, 33.9% reported current e-cigarette use. Junior and senior students, as well as prior tobacco users, were more likely to be current vapers. Prior vaping experience was more prevalent among Hispanic individuals and those with a history of tobacco use. Notably, 74.3% of current users attempted to quit in the past year, with a higher frequency of quit attempts among females, Hispanic students, and those with vaping acquaintances. However, the vaping behavior and quit attempt patterns were similar across other categories. This study highlights how various factors influence e-cigarette use among college students. It suggests that prevention and quitting programs should consider the specific needs of different groups. Future studies will continue to look at different student groups to find the most effective ways to help them quit vaping.

Epidemiology of Injury and Illness in North American Professional Men's Soccer: Comparing COVID-19 Lockdown With Previous Seasons.

After COVID-19 lockdown, studies across Europe and Asia examined its effect on professional soccer injury rates and severity; however, COVID-19 lockdown influence on injuries in United States men's professional soccer has not been evaluated. Injury and illness rates during the 2020 season were higher than the previous 2 seasons. Retrospective observational cohort study. Level 3. Medical staff from participating Major League Soccer (MLS) clubs entered injuries and athletic exposures during the study period into a league-wide electronic medical record system. Injury rate and severity were analyzed to examine differentials between the 2020 COVID season and historical controls. The injury incidence rate per 1000 hours in 2020 was 10.8, ie, higher than 2018 (5.4) and 2019 (5.0) (P < 0.05). Training injury incidence rate increased in 2020 (8.9) compared with 2018 (2.5) and 2019 (2.6) (P < 0.05), whereas match injury incidence decreased in 2020 (18.3) compared with 2018 (24.0) and 2019 (22.7) (P < 0.05). Incidence rates of lower extremity muscle injuries (6.04), anterior cruciate ligament (ACL) injuries (0.17), and concussions (0.49) were also higher in 2020 compared with 2018 (2.5, 0.07, 0.27) and 2019 (2.36, 0.05, 0.22) (P < 0.05). More injured players in 2020 missed >90 days (17.7%) than in 2018 (10.2%) and 2019 (10.1%) (P < 0.05). Incidence of all non-COVID-19 illness was higher in 2020 (3.93) than 2018 (1.53) and 2019 (1.32) (P < 0.05). During 2020, there were significant increases in incidence rates of overall injuries, training injuries, lower extremity muscular injuries, ACL injuries, concussions, and non-COVID illness, along with a higher percentage of players missing >90 days compared with the 2 previous seasons. These results may help clarify the effects of future MLS inseason work stoppages and periods of restricted training.

Forced convective tangent hyperbolic nanofluid flow subject to heat source/sink and Lorentz force over a permeable wedge: Numerical exploration

Abstract The magnetohydrodynamics tangent hyperbolic nanofluid (THNF) flow with the mutual impact of melting heat transfer and wedge angle over a permeable wedge is investigated numerically in the present study. Electronic devices generate excessive heat during operations, so THNF is often employed to regulate them. THNF has the ability to neutralize heat with greater efficacy, thereby reducing the probability of overheating. The influence of thermal radiation, Soret and Dufour, and heat source/sink is also observed on the fluid flow. The modeled equations are simplified to the lowest order through the similarity conversion. The obtained set of dimensionless equations is further calculated numerically by employing the parametric continuation method. The computational findings of the present study are compared to the published results for accuracy purposes. It has been detected that the results are precise and reputable. Moreover, from the graphical results, it has been perceived that the effect of permeability factor (K p) reduces the fluid flow. The rising effect of wedge angle factor enhances the energy dissemination rate and shearing stress; however the augmentation of Weissenberg number drops skin friction and energy transference rate.

Structural, linear/non-linear optical, and optoelectrical properties of PVB/Bi2WO6 nanocomposite for industrial applications

Nanocomposite films composed of polyvinyl butyral (PVB) and Bi2WO6 were produced through solution casting. The goal of this investigation was to examine the effects of different Bi2WO6 concentrations (0%, 2%, and 4% wt.) on the linear/non-linear optical and optoelectrical properties, as well as the structure and dispersion of films of PVB/Bi2WO6 nanocomposite. The direct band gap Eg1 value falls from 5.1 eV to 3.83 eV with the progressive increase in Bi2WO6 content from 0% to 4% wt., while indirect band gap Eg2 decreased from 4.1 eV to 2.89 eV. Conversely, the PVB + 4% Bi2WO6 nanocomposite increased Urbach’s energy (EU) from 1.00 eV for pure PVB to 1.97 eV. Moreover, our research has documented the impact of different concentrations of Bi2WO6 on a range of optical properties, including the refractive index ( n), extinction coefficient ( k), and other pertinent parameters. Utilizing the real and imaginary components of the dielectric constants εr and εi, an investigation was carried out into the dielectrics’ behavior and the optoelectrical parameters’ calculation. Furthermore, investigations were performed on the linear optical susceptibility, the non-linear refractive index, and the third-order non-linear optical susceptibility concerning the concentrations of Bi2WO6. In addition, the results indicated that varying Bi2WO6 concentrations substantially affect the oscillator strength, average oscillator wavelength, and optical conductivity. The nanocomposite films of PVB/Bi2WO6 concentrations exhibited favorable associations between their optoelectrical and non-linear/linear optical parameters, rendering them viable candidates for implementation in flexible electronic devices and radiation shielding.

Liquid Metal Printed Semiconductor

Liquid metal electronic ink (e‐ink) that made from gallium, indium, tin, zinc, bismuth or their alloy is promising new generation material for printed electronics. Extended from this ideal platform, such ink can be post‐processed or loaded with semiconductor nanoparticles to further make semiconductors in the forms of dots, wires and films on its surface. In this way, targeted semiconductors can be quickly fabricated and patterned as desired via the printing way with low cost at around the room temperature. This leads to the unconventional bottom‐up strategy for direct additive manufacture of functional devices. Along this direction, a series of p‐n junction diodes, field effect transistors and light‐emitting devices have been developed so far. It is clear that the liquid metal printed semiconductor would significantly innovate the classical processes of preparing integrated circuits (IC) and electronic devices. To push forward further progress of this cutting‐edge frontier, this article is dedicated to present an overview of liquid metal printed semiconductor. We first introduce the material category of liquid metal semiconductor e‐inks and their synthesis approaches. Then the core strategies toward printing semiconductors are systematically outlined. Following that, we summarize the typical printed semiconductor materials and electronic devices thus constructed as well as their potential applications. Lastly, scientific and technical challenges thus raised are interpreted. Perspective in the area is given.This article is protected by copyright. All rights reserved.

Artificial Intelligence in Electronics and Communication

In today’s rapidly evolving technological landscape, artificial intelligence (AI) integration has ushered in a new era of innovation and efficiency across numerous industries. One domain where AI is making profound contributions is electronics and communication design. A new era of efficiency, invention, and connectedness has been brought about by the integration of AI into electronic gadgets and communication networks. AI fundamentally transforms the electronics design process from automating schematic design and optimizing component selection to enhancing printed circuit board layouts and predicting failure modes.AI-driven speech recognition technology has improved the accuracy and reliability of voice- activated systems

High-temperature dielectric with excellent capacitive performance enabled by rationally designed traps in blends

Polymer dielectrics with excellent capacitive performance are urgently needed in advanced electrical and electronic systems. However, due to the dramatic increase in the conduction loss, the energy density and efficiency of polymers degrade severely at elevated temperatures, limiting their application in harsh environments up to 150 °C. Herein, an all-organic polyurea (PU)/polyetherimide (PEI) blend film is designed to prepare high-temperature polymer dielectric. It is found that carrier traps can be introduced by blending, and the hydrogen bond between PU and PEI increases the trap depth, leading to suppressed leakage current and enhanced breakdown strength, thus improving the energy storage performance. PU/30%PEI exhibits a high discharged energy density of ∼3.74 J/cm3 with an efficiency higher than 90% at 150 °C, which is 78% and 70% higher than pristine PU and PEI, respectively. This work provides a facile strategy to improve the energy storage performance of polymer dielectrics by introducing deep traps through blending.

Nanoskiving of van der Waals Materials toward Edge/Basal Plane Contact Heterojunctions for High-Performance Photodetection.

The unique features of edges in van der Waals materials may lead to edge-basal plane contacts that could provide new opportunities for electronic and optoelectronic devices. However, few studies have addressed edge/basal plane contact heterojunctions owing to the formidable challenges in integrating edges with the basal plane to form a heterojunction. Here, taking the example of black phosphorus (BP)/ReS2, a heterojunction with contact between the edge and the basal plane was successfully achieved by the introduction of a nanoskiving technique to fabricate BP edges with controlled orientation, followed by the dry transfer of a ReS2 flake. The deformation of BP during the nanoskiving process was clearly revealed, where interlayer slipping in the BP determined the formation of the edges. The edge/basal plane contact heterojunctions based on BP/ReS2 exhibited a reverse-rectifying behavior upon contact, and a high rectifying current was attributed to direct tunneling and Fowler-Nordheim tunneling in low and high bias regimes, respectively. As a photodetector, the heterojunction diode demonstrated an impressive responsivity of 65 A/W, a rapid response time (<10 ms), and polarization-sensitive detection under 532 nm illumination without gate biasing.

Extracting Pulmonary Nodules and Nodule Characteristics from Radiology Reports of Lung Cancer Screening Patients Using Transformer Models

Abstract Pulmonary nodules and nodule characteristics are important indicators of lung nodule malignancy. However, nodule information is often documented as free text in clinical narratives such as radiology reports in electronic health record systems. Natural language processing (NLP) is the key technology to extract and standardize patient information from radiology reports into structured data elements. This study aimed to develop an NLP system using state-of-the-art transformer models to extract pulmonary nodules and associated nodule characteristics from radiology reports. We identified a cohort of 3080 patients who underwent LDCT at the University of Florida health system and collected their radiology reports. We manually annotated 394 reports as the gold standard. We explored eight pretrained transformer models from three transformer architectures including bidirectional encoder representations from transformers (BERT), robustly optimized BERT approach (RoBERTa), and A Lite BERT (ALBERT), for clinical concept extraction, relation identification, and negation detection. We examined general transformer models pretrained using general English corpora, transformer models fine-tuned using a clinical corpus, and a large clinical transformer model, GatorTron, which was trained from scratch using 90 billion words of clinical text. We compared transformer models with two baseline models including a recurrent neural network implemented using bidirectional long short-term memory with a conditional random fields layer and support vector machines. RoBERTa-mimic achieved the best F1-score of 0.9279 for nodule concept and nodule characteristics extraction. ALBERT-base and GatorTron achieved the best F1-score of 0.9737 in linking nodule characteristics to pulmonary nodules. Seven out of eight transformers achieved the best F1-score of 1.0000 for negation detection. Our end-to-end system achieved an overall F1-score of 0.8869. This study demonstrated the advantage of state-of-the-art transformer models for pulmonary nodule information extraction from radiology reports.