Electrochemical Active Surface Area Research Articles

Durability Investigation of Low Pt-Loaded PEM Fuel Cells with Different Catalyst Layer Morphologies

This study investigates the durability of proton exchange membrane fuel cells against the Pt-dissolution degradation mechanism using a triangular accelerated stress test (AST) within the voltage range of 0.6-1 V. The electrochemical active surface area and polarization curves are reported throughout the AST for three different catalyst layers (CL), all featuring 0.1 mg/cm2 Pt loading but with different morphologies, which include the Pt/C weight percentages, dilution ratio, and thickness. In addition, a numerical model is employed to simulate the electrochemical performance of these samples at the beginning and end of life, considering the variations in the oxygen transport resistances and catalyst structure.

Bifunctional Strontium Cobalt Molybdenum Oxide (Sr2CoMoO6) Perovskite as an Efficient Catalyst for Electrochemical Water Splitting Reactions in Alkaline Media

Developing earth‐abundant low‐cost electrocatalysts is of prime research interest towards the need for clean energy technology, such as water‐splitting reactions. Herein, we have explored the electrocatalytic activity of the double perovskite‐based strontium cobalt molybdenum oxide (SCMO) towards water‐splitting reactions, both hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). Prepared by scalable autocombustion synthesis, the as‐synthesised bulk SCMO perovskite exhibited impressive electrocatalytic performance attributed to its substantial electrochemical active surface area. For the OER, it exhibited an overpotential of 350 mV with a Tafel slope value of 76 mV/dec. Concurrently, it showed proficient activity in the HER, revealing an overpotential of 270 mV and a Tafel slope of 112 mV/dec. Further, this perovskite material was stable during continuous electrocatalysis over a 24 h period with a negligible increase in observed overpotential value. The electronic density of states confirmed that the Co plays a pivotal role in enhancing electrocatalytic activities. This is achieved by a substantial reduction in the band gap and enhancement of the d‐band centre to an optimal level, rendering the system more favourable for electrocatalytic reactions. Our study contributes insights to the advancement of the design and utilization of perovskite‐based catalysts in the realm of sustainable energy technologies.

Gold nanodendrites enriched with gold nanoclusters on carbon-fiber as flexible acetaminophen sensor for clinical diagnostics

In this work, we demonstrate a flexible acetaminophen (APAP) microsensor based on gold dendrites decorated with gold nanoclusters on flexible carbon fiber (AuDS-AuNC|FCF) microelectrodes. The AuDS-AuNC|FCF microelectrodes are fabricated with a facile and single-step electrochemical strategy for electrocatalytic oxidation and sensing acetaminophen in a 0.1 M phosphate buffer (PB) (pH ∼7.4) solution. The as-developed AuDS-AuNC|FCF microsensors demonstrate excellent electrocatalytic oxidation of acetaminophen with a low oxidation potential of ∼0.54 V (vs. Ag/AgCl) and high catalytic current of ∼1.33 μA. This is because they have a lot of active sites, a large quantity of electrochemical active surface area (ECSA), and gold nanoclusters that are spread out homogeneously. The AuDS-AuNC|FCF microsensors exhibit fast sensing response time of ∼5.0 s, low experimental detection limit of ∼5.0 nM, high sensitivity of ∼0.375 ± 0.017 mA μM−1 cm−2 with a broad linear range of 5.0 nm–500.0 mM, good reproducibility, and possessed a robust anti-interference ability against sensing acetaminophen in the presence of potential interferences such as ascorbic acid, uric acid, adenine, guanine, glucose, etc. Notably, the present microsensor platform based on AuDS-AuNC|FCF microelectrodes is successfully tested for sensing acetaminophen in practical human serum samples, demonstrating its practicability in clinical diagnostics.

Activating Inert Perovskite Oxides for CO2 Electroreduction via Slight Cu2+ Doping in B-Sites.

Perovskite oxides are proven as a striking platform for developing high-performance electrocatalysts. Nonetheless, a significant portion of them show CO2 electroreduction (CO2RR) inertness. Here a simple but effective strategy is reported to activate inert perovskite oxides (e.g., SrTiO3) for CO2RR through slight Cu2+ doping in B-sites. For the proof-of-concept catalysts of SrTi1-xCuxO3 (x=0.025, 0.05, and 0.1), Cu2+ doping (even in trace amount, e.g., x=0.025) can not only create active, stable CuO6 octahedra, increase electrochemical active surface area, and accelerate charge transfer, but also significantly regulate the electronic structure (e.g., up-shifted band center) to promote activation/adsorption of reaction intermediates. Benefiting from these merits, the stable SrTi1-xCuxO3 catalysts feature great improvements (at least an order of magnitude) in CO2RR activity and selectivity for high-order products (i.e., CH4 and C2+), compared to the SrTiO3 parent. This work provides a new avenue for the conversion of inert perovskite oxides into high-performance electrocatalysts toward CO2RR.

Phase Engineering of High‐Entropy Alloy for Enhanced Electrocatalytic Nitrate Reduction to Ammonia

Directly electrochemical conversion of nitrate (NO3−) is an efficient and environmentally friendly technology for ammonia (NH3) production but is challenged by highly selective electrocatalysts. High‐entropy alloys (HEAs) with unique properties are attractive materials in catalysis, particularly for multi‐step reactions. Herein, we first reported the application of HEA (FeCoNiAlTi) for electrocatalytic NO3− reduction to NH3 (NRA). The bulk HEA is active for NRA but limited by the unsatisfied NH3 yield of 0.36 mg h−1 cm−2 and Faradaic efficiency (FE) of 82.66%. Through an effective phase engineering strategy, uniform intermetallic nanoparticles are introduced on the bulk HEA to increase electrochemical active surface area and charge transfer efficiency.The resulting nanostructured HEA (n‐HEA) delivers enhanced electrochemical NRA performance in terms of NH3 yield (0.52 mg h−1 cm−2) and FE (95.23%). Further experimental and theoretical investigations reveal that the multi‐active sites (Fe, Co, and Ni) dominated electrocatalysis for NRA over the n‐HEA. Notably, the typical Co sites exhibit the lowest energy barrier for NRA with *NO + H+ + e− → *NOH as the rate‐determining step.

Phase Engineering of High-Entropy Alloy for Enhanced Electrocatalytic Nitrate Reduction to Ammonia.

Directly electrochemical conversion of nitrate (NO3-) is an efficient and environmentally friendly technology for ammonia (NH3) production but is challenged by highly selective electrocatalysts. High-entropy alloys (HEAs) with unique properties are attractive materials in catalysis, particularly for multi-step reactions. Herein, we first reported the application of HEA (FeCoNiAlTi) for electrocatalytic NO3- reduction to NH3 (NRA). The bulk HEA is active for NRA but limited by the unsatisfied NH3 yield of 0.36 mg h-1 cm-2 and Faradaic efficiency (FE) of 82.66%. Through an effective phase engineering strategy, uniform intermetallic nanoparticles are introduced on the bulk HEA to increase electrochemical active surface area and charge transfer efficiency.The resulting nanostructured HEA (n-HEA) delivers enhanced electrochemical NRA performance in terms of NH3 yield (0.52 mg h-1 cm-2) and FE (95.23%). Further experimental and theoretical investigations reveal that the multi-active sites (Fe, Co, and Ni) dominated electrocatalysis for NRA over the n-HEA. Notably, the typical Co sites exhibit the lowest energy barrier for NRA with *NO + H+ + e- → *NOH as the rate-determining step.

Tailoring the high-density active sites via metal-coordinated ionic liquid encapsulated trimetallic core-shell MOF-derived catalysts for superior ORR in flexible Al-air batteries

The attainment of practicality in flexible Al-air batteries is impeded by the need for efficient air cathodes. To address this challenge, we systematically engineered the trimetallic (ZnCoFe)NC catalyst with a unique morphology of nitrogen-doped carbon nanotubes (NCNTs) on the 3D polyhedral structure (IL-ZnCoFe@CNT/NC) as an effective cathode. The augmented growth of NCNT facilitated by the metal-coordinated ionic liquid enhances both the specific surface area and the electrochemically active surface area (ECSA). As a result, IL-ZnCoFe@CNT/NC material exhibits a higher onset (1.0 V vs RHE) and half-wave potential (E1/2 = 0.89 V vs. RHE) as well as low Tafel slope (61 mV/dec) and surpassed the bare MOF-derived catalysts and Pt/C. E1/2 decreased by only 7 mV after the stability test describes the durability and fast reaction kinetics in the ORR. Upon testing on flexible Al-air with IL-ZnCoFe@CNT/NC cathode catalysts, it exhibited an OCV of 1.49 V and a peak power density of 34.7 mW cm−2 with 1.3 times higher power performance than the commercial Pt/C along with 3 times longevity than bare catalysts. Additionally, the Density-functional theory (DFT) calculations provide rational evidence that the IL-ZnCoFe@CNT/NC catalyst has an upshifted d-band center, which, in turn, enhances the adsorption of reaction intermediates, making the catalyst highly promising towards ORR.

Preparation of Oxygen Reduction Catalyst Electrodes by Electrochemical Acidification and Synergistic Electrodeposition

A proton exchange membrane fuel cell (PEMFC) is an efficient and environmentally friendly power production technology that uses hydrogen energy. The cathodic oxygen reduction electrode is a critical component in the development of PEMFC. Most techniques deposit catalyst nanoparticles in areas that are inaccessible for catalytic processes, reducing platinum utilization. The substrate used in this study was carbon paper (CP) with a self-supporting structure. First, electrochemical acidification technology was employed to modify the CP’s surface, followed by nanoparticle manufacturing and fixation on the CP in a single step by electrodeposition. The Pt/C0.5V2.24CP catalyst electrode demonstrated high-quality activity in the oxygen reduction reaction (ORR), with a homogeneous particle dispersion and particle size of around 50 nm. The mass activity and electrochemical active surface area (ECSA) of the Pt/C0.5V2.24CP catalyst electrode were 1.74 and 3.98 times higher than those of the Pt/C/CP-1 electrodes made with commercial catalysts, respectively. After 5000 cycles of accelerated durability testing (ADT), the mass activity and ECSA were 1.28 times and 6.16 times more than Pt/C/CP-1. This paper successfully proved the viability of electrodepositing Pt nanoparticles on CP following acidification, and that the electrochemical acidification methods have a positive influence on improving electrode ORR activity.

Experimental investigation of degradation mechanism in proton exchange membrane water electrolyzer under prolonged and severe bubble accumulation condition

Proton exchange membrane water electrolyzer (PEMWE) exhibits significant potential as a technology for hydrogen production driven by sustainable energy sources. In this study, the performance degradation characteristics of PEMWE under severe bubble accumulation condition lasting 100 h were investigated through in-situ and ex-situ characterization techniques. The results show that an increasing performance disparity with higher voltage, notably at lower temperatures, reaching a 58.2 % current density degradation rate at 50 °C and 2.0 V. Electrochemical impedance spectroscopy (EIS) analysis suggests that electrolyzer performance degradation is mainly due to increased charge transfer impedance, especially at the anode. In addition, the degraded electrolyzer exhibits a significant delay in reaching a stable current density during the abrupt voltage loading process, and its Tafel slope and electrochemically active surface area (ECSA) increased and decreased by 12.8 % and 13.5 %, respectively. Based on scanning electron microscopy (SEM) images, post-experiment analysis reveals pronounced thinning and noticeable cracks in both cathode and anode catalyst layers near the outlet, particularly on the anode side. Additionally, energy dispersive spectroscopy (EDS) mappings and transmission electron microscopy (TEM) images confirm substantial Pt/C and IrO2 catalyst particle dissolution, migration, and agglomeration. The findings of this study contribute to enhancing understanding of the performance degradation mechanisms in PEMWE.

Co3O4 derived ZnO: An effective electrocatalyst for oxygen evolution reaction in alkaline media

The growing accessibility of hydrogen and renewable energy sources has led to a rising significance of cobalt oxide (Co3O4)-based electrocatalysts in the context of effective electrochemical water splitting. Among two-half cell reactions, oxygen evolution reaction (OER) is more complicated and sluggish in behaviour. We present a composite material based on cobalt oxide-derived zinc oxide (Co3O4@ZnO) prepared through a wet chemical technique to overcome this challenge. The as-prepared materials are analyzed for crystallinity, morphology, and chemical bonding through X-ray diffraction (XRD), scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS), high resolution transmission electron spectroscopy (HRTEM), and Fourier transform infrared (FTIR) spectroscopy, respectively. The optimized electrocatalyst reveals higher electrochemical performance for OER with an overpotential value of 262 mV at 10 mA/cm2 current density, Tafel slope value of 59 mV/dec, and charge transfer resistance (Rct) of 72 Ω. Moreover, the electrochemical active surface area (ECSA) is calculated as 320 cm2. Notably, the desired electrocatalyst shows the stability of 50 h at 10 and 20 mA/cm2 current densities. The as-prepared catalyst (Co3O4@ZnO) with effective electrochemical features can be a potential candidate for energy conversion applications toward a sustainable society.

Benchmarking the Intrinsic Activity of Transition Metal Oxides for the Oxygen Evolution Reaction with Advanced Nanoelectrodes

AbstractThe intrinsic activity assessment of transition metal oxides (TMOs) as key electrocatalysts for the oxygen evolution reaction (OER) has not been standardized due to uncertainties regarding their structure and composition, difficulties in accurately measuring their electrochemically active surface area (ECSA), and deficiencies in mass‐transfer (MT) rates in conventional measurements. To address these issues, we utilized an electrodeposition‐thermal annealing method to precisely synthesize single‐particle TMOs with well‐defined structure and composition. Concurrently, we engineered low roughness, spherical surfaces for individual particles, enabling precise measurement of their ECSA. Furthermore, by constructing a conductor‐core semiconductor‐shell structure, we evaluated the inherent OER activity of perovskite‐type semiconductor materials, broadening the scope beyond just conductive TMOs. Finally, using single‐particle nanoelectrode technique, we systematically measured individual TMO particles of various sizes for OER, overcoming MT limitations seen in conventional approaches. These improvements have led us to propose a precise and reliable approach to evaluating the intrinsic activity of TMOs, not only validating the accuracy of theoretical calculations but also revealing a strong correlation of OER activity on the melting point of TMOs. This discovery holds significant importance for future high‐throughput material research and applications, offering valuable insights in electrocatalysis.

Influence Factors of Platinum Dissolution in Proton Exchange Membrane Fuel Cells: A Sensitivity Study

Abstract Polymer electrolyte fuel cells for heavy-duty applications require lifetimes beyond 30,000 hours, which poses a durability challenge. In this study, we investigated the influence of various factors on loss of electrochemically active surface area (ECSA) in the cathode, which is a major limiting factor. We derive a parameter range from simulated drive cycles showing that the voltage ranges between 0.70 and 0.85 V and that the cells are in idle state at upper potential limit (UPL) most of the time. We evaluate the influence and interaction of UPL, lower potential limit (LPL), temperature, relative humidity, and cycle time on ECSA and performance at four different operating conditions after 10,000 potential cycles based on 25 experiments. The results indicate that UPL and the hold time at UPL have the strongest impact on degradation, while LPL has a small impact, which does not increase below the potential of full platinum reduction (0.55 V) or hold times longer than 2 seconds. Furthermore, the interaction of humidity with other factors becomes significant for long experiment times. In summary, the findings of this work can serve as guidelines for minimizing ECSA loss, e.g. by keeping the fuel cell in a benign operation regime via systems control

Benchmarking the Intrinsic Activity of Transition Metal Oxides for the Oxygen Evolution Reaction with Advanced Nanoelectrodes.

The intrinsic activity assessment of transition metal oxides (TMOs) as key electrocatalysts for the oxygen evolution reaction (OER) has not been standardized due to uncertainties regarding their structure and composition, difficulties in accurately measuring their electrochemically active surface area (ECSA), and deficiencies in mass-transfer (MT) rates in conventional measurements. To address these issues, we utilized an electrodeposition-thermal annealing method to precisely synthesize single-particle TMOs with well-defined structure and composition. Concurrently, we engineered low roughness, spherical surfaces for individual particles, enabling precise measurement of their ECSA. Furthermore, by constructing a conductor-core semiconductor-shell structure, we evaluated the inherent OER activity of perovskite-type semiconductor materials, broadening the scope beyond just conductive TMOs. Finally, using single-particle nanoelectrode technique, we systematically measured individual TMO particles of various sizes for OER, overcoming MT limitations seen in conventional approaches. These improvements have led us to propose a precise and reliable approach to evaluating the intrinsic activity of TMOs, not only validating the accuracy of theoretical calculations but also revealing a strong correlation of OER activity on the melting point of TMOs. This discovery holds significant importance for future high-throughput material research and applications, offering valuable insights in electrocatalysis.

Intrinsically stretchable jellyfish-like gold nanowires film as multifunctional wearable chemical and physical sensors

We report on an intrinsically stretchable jellyfish-like gold nanowires film as a multifunctional wearable platform that can detect both chemical and physical biometrics. The film inherently exhibits multifunctionality, serving directly as an electrochemical electrode, strain sensor, temperature sensor, pressure sensor, and noncontact humidity sensor without the need of any additional materials. Our results highlight the excellent electrochemical properties, evidenced by a large electrochemical active surface area (EASA) of approximately 22.39 cm2 and the ability to withstand significant strain values up to 70 %. Leveraging these attributes, a stretchable electrochemical glucose biosensor was further designed with high sensitivity (45.40μA·mM−1·cm−2) and low limit of detection (10 μM). In addition, its sensing applications in strain, temperature, pressure and noncontact humidity were systematically explored. Impressively, the gold film is capable of monitoring multiple human motions and physiological signals, including joints bending, pulse motions, throat motions (e.g., drinking, speaking, swallowing and pronunciation recognition) and breathing. Furthermore, the film exhibited great versatility by integrating with 3D printing hydrogels, enabling customized patterning. The results demonstrate that our gold nanowires coating approach represent a new route to design multimodal soft wearable platforms for applications in personalized medicine and next-generation healthcare systems.

Electrocatalytic properties of Ni–Cu structures fabricated by electrodeposition of Cu on Ni cones

Ni–Cu alloys are a suitable candidate as a catalyst in Hydrogen Evolution Reaction due to their catalytic performance and good stability. To enhance this activity more, the active surface area of the material should be enhanced. It is commonly achieved by the synthesis of metals and alloys in the form of nanostructures. In this work, Ni cones fabricated by the one-step method were applied as a substrate for the deposition of thin Cu layers. Then, these materials were annealed in an ambient atmosphere to obtain Ni–Cu structures. The investigation of changes in morphology and chemical composition, as well as roughness and wettability before and after the annealing process was performed. Moreover, the measurements of catalytic properties were carried out in 1 M NaOH. The values of the Tafel slope and the electrochemical active surface area were studied. The proposed method can be successfully applied to fabricate structures of other alloys for the desired properties.

Electrocatalytic sensing of propyl gallate in real-time food samples using a synergistic Sm-MOF@GCN composite modified glassy carbon electrode

A novel electrochemical sensor has been developed using the sonochemically synthesized samarium metal–organic framework (Sm-MOF) and the graphitic carbon nitride (GCN) composite for the selective determination of propyl gallate (PG). The as-synthesized Sm-MOF@GCN composite was characterized by XRD, XPS, and FESEM. The morphological studies of the prepared Sm-MOF@GCN composite revealed the bar-shaped Sm-MOF and porous sheet-like morphology of GCN. The combined effect of the Sm-MOF and GCN enhance the current density response and lowers the oxidation potential, which was beneficial for the electrochemical sensing of PG. Moreover, the high electrochemical active surface area (EASA) (0.0649 cm2) and the rate constant value (Ko) of 1.44x10-5 cm s−1 confirm the faster electron transfer kinetics at the interface of Sm-MOF@GCN composite. However, the developed Sm-MOF@GCN composite possesses linear range from 0.02 to 60 µM with a nanomolar detection level (2.05 nM), high sensitivity (0.1914 μA μM−1 cm−2), excellent reproducibility, repeatability, and stability for up to 30 days towards the PG detection. Finally, the Sm-MOF@GCN composite-modified electrocatalyst was utilized for the quantification of PG in foodstuffs such as instant noodles, cookies, cakes, and oils. The result of the study, the Sm-MOF@GCN composite displayed good recovery results, making it a promising candidate for detecting PG in real-world samples in view of its binder-free approach and facile fabrication process.

Preparation of highly active and durable electrodes for alkaline water electrolysis by anodizing of commercial FeNi and FeNiCo alloys

Anodizing is gaining popularity as a binder-free fabrication route for obtaining catalyst materials directly on the current collector without using noble metals, binders, or conductive carbon additives. Here, we fabricate promising highly active electrodes for alkaline water electrolysis by anodizing commercial FeNi and FeNiCo alloys (%wt. Fe range between 22 and 63) in an ethylene glycol-based fluoride electrolyte. Anodizing forms metal fluoride coatings, which are converted to OER active compounds (γ-NiOOH:Fe) during potential cycling in an alkaline aqueous solution (1 mol L−1 (M) KOH at 293 K) as a result of leaching of fluoride ions. The morphology, thickness, and number of active sites are influenced by the amount of Fe in the alloy, and the electrode with the highest electrochemical active surface area (Kovar alloy with a 54 %wt. Fe) shows the largest OER activity enhancement by anodizing. The performance evaluation in practical conditions (7 mol L−1 KOH at 343 K) demonstrated a highly active performance with an OER potential as low as 1.52 V at a current density of 600 mA cm−2 even for electrodes obtained in alloys with a low amount of Fe (78-Permalloy with a 22 %wt. Fe), demonstrating that anodizing is an effective way to develop highly active OER electrodes from commercially available alloys. On the other hand, anodizing is a good fluoridation route for transition metals with good results in the formation of F-enriched precursors that efficiently promote active phase formation during the catalytic process, offering the possibility of obtaining catalysts directly on the current collector in a one-step process, easily implemented in industrial applications.

Green and sustainable use of macadamia nuts as support material in Pt-based direct methanol fuel cells

The successful commercialization of direct methanol fuel cells (DMFCs) is hindered by inadequate methanol oxidation activity and anode catalyst longevity. Efficient and cost-effective electrode materials are imperative in the widespread use of DMFCs. While Platinum (Pt) remains the primary component of anodic methanol oxidation reaction (MOR) electrocatalysts, its utilization alone in DMFC systems is limited due to carbon monoxide (CO) poisoning, instability, methanol crossover, and high cost. These limitations impede the economic feasibility of Pt as an electrocatalyst. Herein, we present the use of powdered activated carbon (PAC) and granular activated carbon (GAC), both sourced from macadamia nut shells (MNS), a type of biomass. These bio-based carbon materials are integrated into hybrid supports with reduced graphene oxide (rGO), aiming to enhance the performance and reduce the production cost of the Pt electrocatalyst. Electrochemical and physicochemical characterizations of the synthesized catalysts, including Pt-rGO/PAC-1:1, Pt-rGO/PAC-1:2, Pt-rGO/GAC-1:1, and Pt-rGO/GAC-1:2, were conducted. X-ray diffraction analysis revealed crystallite sizes ranging from 1.18 nm to 1.68 nm. High-resolution transmission electron microscopy (HRTEM) images with average particle sizes ranging from 1.91 nm to 2.72 nm demonstrated spherical dispersion of Pt nanoparticles with some agglomeration across all catalysts. The electrochemical active surface area (ECSA) was determined, with Pt-rGO/GAC-1:1 exhibiting the highest ECSA of 73.53 m2 g−1. Despite its high ECSA, Pt-rGO/GAC-1:1 displayed the lowest methanol oxidation reaction (MOR) current density, indicating active sites with poor catalytic efficiency. Pt-rGO/PAC-1:1 and Pt-rGO/PAC-1:2 exhibited the highest MOR current densities of 0.77 mA*cm−2 and 0.74 mA*cm−2, respectively. Moreover, Pt-rGO/PAC-1:2 and Pt-rGO/PAC-1:1 demonstrated superior electrocatalytic mass (specific) activities of 7.55 mA/mg (0.025 mA*cm−2) and 7.25 mA/mg (0.021 mA*cm−2), respectively. Chronoamperometry tests revealed Pt-rGO/PAC-1:2 and Pt-rGO/PAC-1:1 as the most stable catalysts. Additionally, they exhibited the lowest charge transfer resistances and highest MOR current densities after durability tests, highlighting their potential for DMFC applications. The synthesized Pt supported on PACs hybrids demonstrated remarkable catalytic performance, stability, and CO tolerance, highlighting their potential for enhancing DMFC efficiency.

Cu2MoS4 Nanocatalyst-Based Electrochemical Sensor for Ofloxacin Electro-Oxidation: Delineating the Combined Roles of Crystallinity and Morphology on the Analytical Performance.

In this study, we demonstrate the influence of crystallinity and morphology on the analytical performance of various Cu2MoS4 (CMS) nanocatalysts-based electrochemical sensors for the high-efficiency detection of Ofloxacin (OFX) antibiotic. The electrochemical kinetics parameters including peak current response (ΔIp), peak-to-peak separation (ΔEp), electrochemically active surface area (ECSA), electron-transfer resistance (Rct), were obtained through the electrochemical analyses, which indicate the single-crystalline nature of CMS nanomaterials (NMs) is beneficial for enhanced electron-transfer kinetics. The morphological features and the electrochemical results for OFX detection substantiate that by tuning the tube-like to plate-like structures of the CMS NMs, it might noticeably enhance multiple adsorption sites and more intrinsic active catalytic sites due to the diffusion of analytes into the interstitial spaces between CMS nanoplates. As results, highly single-crystalline and plate-shaped morphology structures of CMS NMs would significantly enhance the electrocatalytic OFX oxidation in terms of onset potential (Eonset), Tafel slope, catalytic rate constant (kcat), and adsorption capacity (Γ). The CMS NMs-based electrochemical sensing platform showed excellent analytical performance toward the OFX detection with two ultra-wide linear detection concentration ranges from 0.25-100 and 100-1000 μM, a low detection limit of 0.058 μM, and an excellent electrochemical sensitivity (0.743 μA μM-1 cm-2).

Chrysanthemum‐Flowers‐Like Bimetal Oxide Based Electrocatalyst for Methanol Oxidation Reaction

Transition metal oxides have garnered attention for the methanol electro‐oxidation reaction owing to their easy availability, high catalytic applicability, and multiple oxidation capabilities. Bimetal‐based catalysts further enhance the performance of the methanol oxidation reaction. In this context, a chrysanthemum‐flower‐like MoO2/WO3 is synthesized through a solvothermal and annealing strategy. The morphology attests to the rough surface and pores in the catalyst, augmenting its surface area for reactions and enhancing catalytic applicability. Electrochemical oxidation of methanol yields an optimal current density of 0.99 mA cm−2 and 2.07 mA mg−1 at a potential of 0.57 V versus Ag/AgCl. The catalyst exhibits a remarkably low Tafel slope of 37.45 mV dec−1, affirming its rapid reaction kinetics. Electrochemical impedance spectroscopy (EIS) reveals an equivalent electronic circuit of R(Q(R(QR)Q(RW))), confirming low charge transfer resistance (Rct) and diffusion‐controlled kinetics attributable to the pores in the sample. The sample also demonstrates an electrochemically active surface area (ECSA) value equal to 0.122 mF cm−2 and long‐term stability over continuous 5000 s, exhibiting no change and high resistance to CO poisoning. All these characterizations and obtained results collectively affirm that the chrysanthemum‐flower‐like MoO2/WO3 serves as a highly suitable electrocatalyst for the electrochemical oxidation of methanol.