Electrochemical Techniques Research Articles

Tailoring the electrical, optical, physical, and photocatalytic properties of indium-doped cerium molybdate microstructures reinforced with a 2D carbonaceous

Composite materials featuring metal oxides incorporated in 2D reduced graphene oxide (rGO) have received significant attention as visible-light-driven photocatalysts to address wastewater treatment. In this study, pure (Ce2(MoO4)3) and indium-doped (In–Ce2(MoO4)3) cerium molybdate microstructures were fabricated by the facile coprecipitation route, and the nanocomposite of doped material with the 2D rGO (In–Ce2(MoO4)3/rGO) by ultrasonication. The effect of indium-doping and composite formation on the microstructural, morphological, optical, electrical, surficial, and thermal properties of the cerium molybdate was investigated by various physical, spectroscopic, and electrochemical techniques. XRD results confirm the successful indium-doping in the host lattice. The photocatalytic potential of the fabricated photocatalysts was estimated by degrading methylene blue (MB) dye as a sample pollutant under visible light irradiation. The composite material exhibited enhanced photocatalytic degradation (k = 0.0355 min−1) of the MB dye in comparison to pure (k = 0.0096 min−1) and doped (0.0131 min−1) materials. This superior catalytic activity of the composite material is credited to the synergism arising from indium doping and composite formation, which extends the visible light absorption, suppresses the fast recombination of charges, and enhances the electrical conductivity of the photocatalyst. The present investigation reveals the promising photocatalytic potential of the as-fabricated composite material (In–Ce2(MoO4)3/rGO) for degrading MB in aqueous media, offering an economical and sustainable strategy to address wastewater treatment and environmental remediation.

Hydrothermal and electrochemical synthesis of Fe2O3 and ZnFe2O4/Fe2O3 photoanodes for photoelectrochemical applications: An experimental and theoretical study

Hematite (Fe2O3) is commonly utilized in the fabrication of photoelectrochemical cells for water-splitting reaction. However, its relatively low efficiency has highlighted the necessity for enhancements in Fe2O3-based photoanodes. In addressing this issue, this study implemented the addition of ZnFe2O4. The pure Fe2O3 was synthesized onto a Fluorine-doped Tin Oxide coated glass by the hydrothermal process, followed by the synthesis of various ZnFe2O4/Fe2O3 heterostructures using electrochemical deposition techniques. The thin film’s composition, surface morphology, and chemical species of the products were analyzed using X-ray Diffraction, Scanning Electron Microscopy, Transmission Electron Microscopy, and X-ray Photoelectron Spectroscopy, respectively. The performance of the Fe2O3-based photoanode was compared to that of various ZnFe2O4/Fe2O3 photoanodes through photoelectrochemical studies. Results indicated that a 50 s electrochemical deposition of ZnFe2O4 on Fe2O3 yielded the highest photoconversion efficiency. Additionally, Density Functional Theory was employed to investigate the electron energy level of ZnFe2O4, revealing alignment with the properties of Fe2O3. Theoretical analysis showed that the Fermi energy of ZnFe2O4 exceeded that of Fe2O3, suggesting a preferable direction for electron transfer from ZnFe2O4 to Fe2O3 which was in consistent to the Mott-Schottky analysis. The performance of the overall ZnFe2O4/Fe2O3 heterostructure photoanodes demonstrated greater efficiency compared to pristine Fe2O3.

Cardiac Troponin I-Responsive Nanocomposite Materials for Voltammetric Monitoring of Acute Myocardial Infarction.

Acute myocardial infarction (AMI) is a severe cardiovascular disease characterized by heart muscle damage due to inadequate blood supply, leading to a life-threatening risk of heart attack. Herein, we report on the design of polyaminophenol-based thin film functional polymers and their thorough optimization by electrochemical, spectroscopic, and microscopic techniques to develop a high-performance point-of-care voltammetric monitoring system. Molecularly imprinted polymer-based cTnI-responsive nanocomposite materials were prepared on an electrode surface by imprinting a specific cTnI epitope, integrating polyaminophenol electrodeposition, along with gold nanoparticles (AuNPs) and graphene quantum dots (GQDs). The characterization techniques, including cyclic and square wave voltammetries, electrochemical impedance spectroscopy, atomic force microscopy, fluorescence microscopy, attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR), and contact angle measurements proved the efficient fabrication of the voltammetric monitoring system relying on cTnI-responsive functional thin films. The sensing platform prepared with the optimized nanocomposite composition of AuNPs, GQDs, and molecularly imprinted polymers exhibited very high sensitivity, reproducibility, specificity, and affinity toward cTnI. The sensor showed a storage stability of 30 days, demonstrating great potential for use in early and point-of-care diagnosis of AMI with its 18 min detection time.

Effect of NOX and SOX Contaminants on Corrosion Behaviors of 304L and 316L Stainless Steels in Monoethanolamine Aqueous Amine Solutions

This work is devoted to evaluating the corrosion behaviors of SS 304L and SS 316L in monoethanolamine solutions (MEA) containing SOX and NOX pollutants, examining both lean and CO2-loaded conditions at 25 °C and 40 °C. Electrochemical techniques (potentiodynamic and cyclic polarization) were used along with Scanning Electron Microscopy, Confocal Microscopy and weight loss measurements. The results reveal that the introduction of SOX and NOX pollutants increased the corrosion rate, whereas CO2 loading primarily reduced the corrosion resistance in the lean MEA solution, while its impact on solutions with SOX and NOX was less pronounced. This suggests that SOX and NOX play primary roles in the metal’s dissolution. Also, SS 316L demonstrated superior corrosion resistance compared to 304L in nearly all of the cases examined. Elevated temperatures were also found to intensify the corrosion rate, indicating a correlation between the corrosion rate and temperature. A microscopic observation and EDX analysis revealed that corrosion products are characterized by high concentrations of iron (Fe) and oxygen (O) as well as carbon (C). There is also an indication of the possible formation of amine complexes, suggesting a potential for amine degradation. No pitting corrosion was observed in SS 304L and SS 316L across any tested solution. Finally, the immersion results expose a tendency for passivity in all amine solutions and at both temperatures after several days of exposure. Moreover, they confirm the very low corrosion rate calculated from potentiodynamic curves due to minimal weight loss after 24 days of immersion.

Artificial Intelligence-Based Microfluidic Platform for Detecting Contaminants in Water: A Review.

Water pollution greatly impacts humans and ecosystems, so a series of policies have been enacted to control it. The first step in performing pollution control is to detect contaminants in the water. Various methods have been proposed for water quality testing, such as spectroscopy, chromatography, and electrochemical techniques. However, traditional testing methods require the utilization of laboratory equipment, which is large and not suitable for real-time testing in the field. Microfluidic devices can overcome the limitations of traditional testing instruments and have become an efficient and convenient tool for water quality analysis. At the same time, artificial intelligence is an ideal means of recognizing, classifying, and predicting data obtained from microfluidic systems. Microfluidic devices based on artificial intelligence and machine learning are being developed with great significance for the next generation of water quality monitoring systems. This review begins with a brief introduction to the algorithms involved in artificial intelligence and the materials used in the fabrication and detection techniques of microfluidic platforms. Then, the latest research development of combining the two for pollutant detection in water bodies, including heavy metals, pesticides, micro- and nanoplastics, and microalgae, is mainly introduced. Finally, the challenges encountered and the future directions of detection methods based on industrial intelligence and microfluidic chips are discussed.

The effects of aging time on the corrosion inhibition performance of KI and its synergistic effect with a typical phosphorus-based ionic liquid inhibitor

Potassium iodide (KI) is regarded as an ideal synergist for typical corrosion inhibitors. However, the synergistic effect of KI may be compromised due to its oxidation in acidic solutions. In this work, the anticorrosion performance of KI with different aging times in HCl solution and their synergistic effect with dodecyltriphenylphosphonium bromide (C12TPB) were evaluated via electrochemical tests and surface characterization techniques. The corrosion inhibition efficiency of KI gradually increased from 6.41 % to 38.99 % with increasing aging time to 6 h, while the synergy coefficient between KI and C12TPB abnormally decreased from greater than 1.0 to less than 0.4. UV–vis results and quantum chemical calculation demonstrated that the generated I3− during the aging process caused negative impact on the adsorption of C12TPB, leading to the reduced anticorrosion performance. This study provides valuable insights for the rational utilization of KI as the corrosion inhibitor and synergist.

3D Printed Interdigitated Electrodes for Cardiac Biomarker Detection.

The identification of biomarkers has significant benefits for early disease diagnosis and treatment. Hence, there is an increasing demand for low-cost, disposable point-of-care diagnostic devices for rapid and specific biomarker detection, with good sensitivity and range. Interdigitated electrodes (IDEs) are among the most widely used transducers, especially in chemical and biological sensors, because of their high sensitivity, low cost, and straightforward manufacturing procedure. In this work, a simple 3D printed IDE structure has been developed for cardiac troponin I detection to indicate the risk of acute myocardial infarction (AMI). IDEs have been fabricated using 3D printing technique and the electrically conductive composite polylactic acid (PLA) filament being utilized for the fabrication of electrodes. The demonstrated cardiac troponin I sensor has a calculated quantification limit and detection limit of 0.233 ng ml-1 and 76.97 pg ml-1, respectively which are clinically significant ranges for AMI identification. Electrochemical analytical techniques, such as electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV), were carried out for the detection of analyte concentration. Furthermore, using this fabrication methodology IDEs can be fabricated for under US$ 0.4 which can be utilized to detect several other biomarkers.

Enzymatic Activation and Continuous Electrochemical Production of Methane from Dilute CO2 Sources with a Self-Healing Capsule.

Converting dilute CO2 source into value-added chemicals and fuels is a promising route to reduce fossil fuel consumption and greenhouse gas emission, but integrating electrocatalysis with CO2 capture still faced marked challenges. Herein, we show that a self-healing metal-organic macrocycle functionalized as an electrochemical catalyst to selectively produce methane from flue gas and air with the lowest applied potential so far (0.06 V vs reversible hydrogen electrode, RHE) through an enzymatic activation fashion. The capsule emulates the enzyme' pocket to abstract one in situ-formed CO2-adduct molecule with the commercial amino alcohols, forming an easy-to-reduce substrate-involving clathrate to combine the CO2 capture with electroreduction for a thorough CO2 reduction. We find that the self-healing system exhibited enzymatic kinetics for the first time with the Michaelis-Menten mechanism in the electrochemical reduction of CO2 and maintained a methane Faraday efficiency (FE) of 74.24% with a selectivity of over 99% for continuous operation over 200 h. A consecutive working lab at 50 mA·cm-2, in an eleven-for-one (10 h working and 1 h healing) electrolysis manner, gives a methane turnover number (TON) of more than 10,000 within 100 h. The integrated electrolysis with CO2 capture facilitates the thorough reduction of flue gas (ca. 13.0% of CO2) and first time of air (ca. 400 ppm of CO2 to 42.7 mL CH4 from 1.0 m3 air). The new self-healing strategy of molecular electrocatalyst with an enzymatic activation manner and anodic shifting of the applied potentials provided a departure from the existing electrochemical catalytic techniques.

Influence of Grain Size and Film Formation Potential on the Diffusivity of Point Defects in the Passive Film of Pure Aluminum in NaCl Solution

The influence of grain size on the corrosion behavior of pure aluminum and the defect density and diffusion coefficient of surface passive films were investigated using electron backscatter diffraction (EBSD) and electrochemical testing techniques, based on the point defect model (PDM). Samples with three different grain sizes (23 ± 11, 134 ± 52, and 462 ± 203 μm) were obtained by annealing at different temperatures and times. The polarization curves and electrochemical impedance spectroscopy results for the pure aluminum in the 3.5% NaCl solution showed that with decreasing grain size, the corrosion current (icorr) decreased monotonously, giving rise to a noble corrosion potential and a large polarization resistance. The Motte–Schottky results showed that the passive films that formed on pure aluminum with fine grains of 23 ± 11 μm had a low density (3.82 × 1020 cm−3) of point defects, such as oxygen vacancies and/or metal interstitials, and a small diffusion coefficient (1.94 × 10−17 cm2/s). The influence of grain size on corrosion resistance was discussed. This work demonstrated that grain refinement could be an effective approach to achieving high corrosion resistance of passive metals.

P-696 Continuous monitoring of female hormones as a tool to improve IVF treatment’s efficacy

Abstract Study question Is it possible to employ an unobtrusive and injectable biosensor for real-time remote monitoring of patient’s hormone levels (LH, P4, E2) during an ART cycle? Summary answer In-situ implantable biosensors can effectively monitor clinically relevant hormone levels in real-time to improve ART cycle. What is known already Worldwide 48.5 million couples suffer from infertility. Hormonal imbalances can impede pregnancy by compromising the intricate processes of the reproductive system, affecting ovulation, egg quality, fallopian tube function, and endometrial receptivity. In the UK, assisted reproductive treatments (ART) have surged ten-fold in the last 20 years. ART success tremendously depends on the accurate measurement of hormone levels, namely Luteinizing Hormone (LH), oestradiol (E2), and progesterone (P4). These hormone levels change and pulsate during each patient cycle, requiring women to undergo a blood draw and endocrinology analysis every 2-3 days, making ART treatment a highly invasive and time consuming method. Study design, size, duration In order to determine the feasibility of the study question, Impli designed a minimally invasive implantable biosensor to continuously monitor essential hormones for women’s fertility such as LH, P4 and E2 in order to enhance the quality of treatment and improve the ART experience. An implantable electrochemical aptamer-based biosensors has been developed using cutting-edge electronics and electrochemical technologies. This minimally invasive biosensor allows patients to monitor their hormone levels in real-time during ART without venipuncture. Participants/materials, setting, methods The implantable biosensor contains the biorecognition interface, designed using the DNA-based aptamers coupled to the detection gold working electrodes. When the biosensor is in touch with the sample, hormones bind to the respective aptamers, which leads to changes in the electrical properties of the gold electrode. The changes are then monitored and calibrated through sensitive electrochemical techniques such as differential pulse voltammetry (DPV), using CHI potentiostat. Main results and the role of chance The biosensor was tested in vitro in artificial interstitial fluid (ISF) containing the range of 1 pg/ml to 1 µg/ml of hormones yielding a limit of detection (LOD) of 0.46 pg/ml, 1.15 pg/ml, and 0.58 pg/ml for E2, P4 and LH, respectively. Our data was validated using ELISA assays. A notably high linear correlation coefficient (R2) of approximately 0.9 was observed between the signals obtained from the ELISA and the biosensors, confirming the reliability of the aptamer biosensors for hormone analysis. The stability of the biosensor was also investigated over one week. The DPV technique was employed to assess the cross-reactivity of potential interferences with each biosensor. The results revealed that each biosensor exhibited notable selectivity towards its respective analyte over other interferences, at significantly higher concentrations. The biosensor was also characterised by microscopy techniques such as SEM and Raman analysis. Limitations, reasons for caution This novel implantable biosensor technology requires further upcoming validation in animal models to assess its ability for widespread use. Once validated, the appropriate human clinical trials will be undertaken. Wider implications of the findings The development and implementation of an unobtrusive implantable remote and continuous monitoring system, capturing hormone concentrations that are vital for success in an ART procedure, could transform the industry and positively influence patient’s access to care and the patient journey. Trial registration number No clinical trial

Assessing tungsten-based electrodes coated with W and Ce oxides for pH sensing applications

AbstractThis study assessed tungsten-based materials with and without dispersed CeO2 for potential use as pH sensors. Specifically, three types of tungsten electrodes were characterized: tungsten electrodes without CeO2 but with native oxide, tungsten electrodes without CeO2 that were oxidized, and a tungsten electrode containing dispersed CeO2 that was oxidized, resulting in a mixture of WO3, CeO2, and Ce2O3. The characterization was performed using SEM/EDAX, X-ray photoelectron spectroscopy (XPS), and electrochemical techniques. The oxide coatings showed higher oxygen contents compared to native tungsten. XPS confirmed the presence of a thick layer of WO3 and cerium oxides. The electrodes exhibited good reproducibility and stability in pH measurements. A linear relationship was found between the open circuit potential and pH, with slopes of 44.9, 40.8, and 46.9 mV pH−1 for native oxide, WO3, and WO3 with CeO2 and Ce2O3, respectively. The latter showed the highest sensitivity and lowest hysteresis. The response times ranged from 14.5–23.5 s and were faster in acidic solutions. Overall, the inexpensive tungsten-based electrodes demonstrated promising capabilities for pH sensing, but in particular ceriated tungsten electrodes.

Microbial electrochemical Cr(VI) reduction in a soil continuous flow system.

Microbial electrochemical technologies represent innovative approaches to contaminated soil and groundwater remediation and provide a flexible framework for removing organic and inorganic contaminants by integrating electrochemical and biological techniques. To simulate in situ microbial electrochemical treatment of groundwater plumes, this study investigates Cr(VI) reduction within a bioelectrochemical continuous flow (BECF) system equipped with soil-buried electrodes, comparing it to abiotic and open-circuit controls. Continuous-flow systems were tested with two chromium-contaminated solutions (20-50 mg Cr(VI)/L). Additional nutrients, buffers, or organic substrates were introduced during the tests in the systems. With an initial Cr(VI) concentration of 20 mg/L, 1.00 mg Cr(VI)/(L day) bioelectrochemical removal rate in the BECF system was observed, corresponding to 99.5% removal within nine days. At the end of the test with 50 mg Cr(VI)/L (156 days), the residual Cr(VI) dissolved concentration was two orders of magnitude lower than that in the open circuit control, achieving 99.9% bioelectrochemical removal in the BECF. Bacteria belonging to the orders Solirubrobacteriales, Gaiellales, Bacillales, Gemmatimonadales, and Propionibacteriales characterized the bacterial communities identified in soil samples; differently, Burkholderiales, Mycobacteriales, Cytophagales, Rhizobiales, and Caulobacterales characterized the planktonic bacterial communities. The complexity of the microbial community structure suggests the involvement of different microorganisms and strategies in the bioelectrochemical removal of chromium. In the absence of organic carbon, microbial electrochemical removal of hexavalent chromium was found to be the most efficient way to remove Cr(VI), and it may represent an innovative and sustainable approach for soil and groundwater remediation. Integr Environ Assess Manag 2024;00:1-17.© 2024 The Author(s). Integrated Environmental Assessment and Management published by Wiley Periodicals LLC on behalf of Society of Environmental Toxicology & Chemistry (SETAC).

A critical review of recent advancements in zinc based metal organic framework nanocomposites and their derivatives for supercapacitor applications with future perspectives and challenges

Among various energy storage materials, Zinc-based metal-organic frameworks (Zn-MOFs used as precursors, templates, and shape controllers) act as potential candidates for supercapacitor (SC) applications due to their remarkable properties, such as facile preparation methods, high specific surface area (SSA), large porosity, outstanding power (Pden) & energy density (Eden), astonishing crystallinity, adjustable sizes, exceptional chemical & thermal stability, elongated life-cycle, framework diversity, and tunable structures. The present review focuses on the most recent progress on pristine Zn-MOFs, nanocomposites (with graphene (Gr), carbon nanotubes (CNTs), and polyaniline (PANI)), and their derivatives (metal oxides (MOs) & hydroxides (MHOs), porous carbon (PC) & activated carbon (AC), and metal sulfides (MSs)) as electrode materials to present the most up-to-date overview in this specific field. We first discuss the fundamental charging mechanisms (electric double-layer capacitance and pseudocapacitance) and the electrochemical techniques (cyclic voltammetry, galvanostatic charge-discharge, and electrochemical impedance spectroscopy) of SCs. We then analyzed different methods with advantages and disadvantages of Zn-based MOF synthesis, such as solvothermal, hydrothermal, sonochemical, microwave heat-assisted, simple stirring, slow evaporation, mechanochemical, and electrochemical. Furthermore, structural, morphological, and electrochemical assessment techniques of reported Zn-based MOFs were examined in detail in three- and two- electrode configurations (asymmetric/symmetric devices with power and energy density). Finally, the ongoing issues and future developments in this field for architecturing supercapacitive devices are also discussed.

Functional and structural modification of polyvinyl alcohol/carbon nanotubes composite fibers

This research was based on the synthesis of new materials with capacitive properties and low cost, seeking efficient energy storage, through the manufacture and characterization of composite materials of polyvinyl alcohol (PVA)/multiwalled carbon nanotubes with carboxyl group (MWCNTs-COOH) (1 %) for electrodes. Forcespinning and electrospinning techniques were used to develop composite fiber films and compare the physical structure of the fibers and its influence on their capacitive properties. These samples were characterized by SEM, FESEM, FT-IR, XRD, TGA, Raman spectroscopy and electrochemical techniques. The characterization of the composites makes evident the structural modification that the material underwent after the treatments. The electrochemical parameters were measured by electrochemical impedance spectroscopy (EIS), with the samples immersed in H2SO4 1 M as electrolyte. The PVA/MWCNTs-COOH composites with thermal treatment (340 °C) showed a considerable decrease in total impedance of up to 6 orders of magnitude (124 Ω) with respect to the blank sample (2.3 × 108 Ω), as a function of the immersion time in the acid solution. As well as, an increase in the specific capacitance of up to 8 orders of magnitude (1.01×10−2 F cm−2) with respect to the blank sample (5.07 × 10−10 F cm−2) for the composite manufactured by the electrospinning technique. The obtaining of fibers with directionality as a result of the forcespinning technique, the highly crossed network observed by electrospinning and the electrochemical properties shown by the structural modification of PVA/MWCNTs-COOH composite, make it, a material with potential technological applications such as electrode in electrochemical capacitors.

Indium-doped tungsten oxide architectures anchored on 2D rGO Matrix with enhanced visible-light-response and efficient charge separation for photocatalytic degradation of organic pollutants

Visible-light-responsive photocatalysis has been recognized as a sustainable strategy to address environmental pollution, but semiconductor-based photocatalysts often suffer from many shortcomings, including low visible light absorption and rapid recombination of photo-generated charge carriers. In this regard, rationally designed composite materials have gained substantial prominence, as achieving an ideal photocatalyst's characteristics in a single component material is frequently difficult. In the present study, we have synthesized pure (WO3) and indium-doped tungsten oxide (In-WO3) by the facile solvothermal route. The doped material was anchored on a 2D rGO matrix to fabricate the In-WO3/rGO composite. The structural, morphological, electrical, and optical properties of the as-synthesized materials were investigated as a function of doping and composite fabrication by various physical and electrochemical techniques. The comparative photocatalytic performance was evaluated by degrading Congo Red (CR) dye and paracetamol (PCM) drug. The composite material shows degradation efficiencies of ~96% (K=0.0174min-1) and ~91% (K=0.0144min-1) for CR dye and PCM drug, respectively. The boosted catalytic performance corresponds to the declined band gap (2.53eV) and increased conductivity (0.1270 Sm-1), which enhances its visible light absorption and a surge in the charge carrier's population. The kinetics, relative contribution of different active species generated, and the potential mechanism of photodegradation reaction are discussed in detail. The significant increase in photocatalytic performance of the fabricated In-WO3/rGO composite discloses its promising catalytic potential for the degradation of recalcitrant organic pollutants.

Effect of anions on formation of ferrite coatings on carbon steel by hydrothermal method

The major concerns in Primary Heat Transport circuits of water cooled nuclear power plants are corrosion of structural materials and radiation field buildup on out-of-core surfaces due to accumulation of activated corrosion products. To address these concerns, hot conditioning and metal ion passivation are employed, which lead to the formation of protective magnetite coating on structural alloys like carbon steel. In this study, investigations were undertaken to modify the magnetite/ferrite films hydrothermally in the presence of zinc (Zn2+) and nickel (Ni2+) ions by using different salts of these ions containing anions such as acetate, nitrate and sulphate. Mixed ferrite coatings containing Zn2+ and Ni2+ ions were developed on carbon steel in lithiated water in presence of these anions at 250 °C by hydrothermal method and subsequently characterized by grazing incidence-X-ray diffraction for phase identification and scanning electron microscopy for surface morphology. The effects of these anions were studied by comparing the corrosion resistance properties of ferrite coated carbon steel specimens. The corrosion properties were studied in lithium hydroxide medium at ambient temperature by electrochemical techniques and the results of the investigation are discussed in this paper.

Improved electro-kinetics of new electrolyte composition for realizing high-performance zinc-bromine redox flow battery

Aqueous Redox Flow Batteries (ARFB) are the most prominent technology for large-scale energy storage applications. The energy density of the ARFBs is mainly determined by the electrolyte components, which highly influence the flow battery performance. In the present work, we acutely investigated the various electrolyte compositions and optimized the best electrolyte for realizing the high performance of Zn-Br2 ARFBs. The electrode kinetics, such as rate constant, exchange current density, conductivity, and diffusion coefficient, were analyzed using electrochemical techniques, cyclic voltammetry, and electrochemical impedance analysis. It was observed that zinc bromide (ZnBr2) + perchloric acid (HClO4) + 1-Ethyl-1-methylmorpholinium bromide (MEM) + N-ethyl-N-methylpyrrolidinium bromide (MEP) and ZnBr2 + zinc chloride (ZnCl2) + MEM + MEP electrolytes showed improved performance, where the redox kinetics of 2Br-/Br2 redox couple is greatly enhanced. The presence of perchloric acid unlocks the capacity of full electro-oxidation of bromide (Br-) to bromine (Br2) as it involves 1e- per Br-, which would be highly beneficial to attain high energy density. Further, Zn-Br2 RFB adopted with optimized electrolyte formulation ZnBr2 + HClO4 + MEM+ MEP shows a better round-trip efficiency and displays a stable long cycling performance over 200 cycles with an energy (EE) and coulombic efficiency (CE) of > 68% and > 92%, respectively.

Cu corrosion in supernatant and sedimentation of bentonite slurry containing chloride

Cu corrosion in aerated NaCl solution containing different bentonite content was investigated using electrochemical impedance spectroscopy and surface analysis techniques. In NaCl solution, Cu corrosion proceeds with CuClads formation and its transformation to Cu2O. The outer deposit layer consists of Cu2O and Cu2(OH)3Cl. The self-catalyzed comproportionation reaction between Cu and CuClx(x−2)− produces CuClx(x−1)−, leading to accelerated Cu corrosion. Bentonite slurry (10-30wt.%) shows supernatant and sedimentation layers. In supernatant layer, Cu corrosion happens with the help of anions dissolved from bentonite minerals. In sedimentation layer, Cu corrosion is hindered due to suppressed cathodic reaction and the self-catalyzed comproportionation reaction.

In situ preparation of MOF-74 for compact zincophilic surfaces enhancing the stability of aqueous zinc-ion battery anodes

Zinc-ion batteries (ZIBs), while celebrated for their environmental friendliness, abundant material availability, and inherent safety, face significant challenges that curtail their performance and lifecycle. These challenges include the formation of zinc dendrites, susceptibility to electrolyte corrosion, and the propensity for hydrogen evolution reactions. Addressing these critical issues, our research introduces an innovative surface modification strategy for zinc anode of ZIB with mild electrolyte, by the in-situ synthesis of Metal-Organic Framework (MOF-74) facilitated by the mild acidity of a 2,5-dihydroxyterephthalic acid (DHTA) methanol solution. The zincophilic sites and pore structure introduced by MOF-74 to substantially enhance the surface properties of zinc anodes and accelerate the solvation process, enabling uniform zinc deposition, inhibiting dendrite growth, and significantly bolstering corrosion resistance and electrochemical stability. Combination of physical and electrochemical characterization techniques are employed to validate the successful implementation of MOF-74 on the zinc anode surface and its resultant benefits. When tested in full cell setups with α-MnO2 as the cathode, the MOF-74 modified zinc anodes displayed exceptional cyclic stability and rate performance, surpassing those of unmodified counterparts. This investigation highlights the potential of MOF materials to address the electrochemical challenges facing zinc anodes, offering a straightforward yet efficacious strategy to enhance the performance and longevity of ZIBs.

Spectroscopic, electrochemical, and molecular docking studies of the interaction between the antihistamine drug desloratadine and dsDNA

Through the utilization of fluorescence spectroscopy, electrochemical, and molecular docking methods, this research investigates the interaction between the antihistamine drug desloratadine and calf thymus double-stranded DNA (ct-dsDNA). Deoxyguanosine (dGuo) and deoxyadenosine (dAdo) oxidation signals were diminished by incubation with varying concentrations of desloratadine, as determined by differential pulse voltammetry (DPV). This change was ascribed to desloratadine's binding mechanism to ct-dsDNA. The binding constant (Kb) between desloratadine and ct-dsDNA was determined to be 2.2 × 105 M-1 throughout electrochemical experiments. In order to further develop our comprehension of the interaction mechanism between desloratadine and ct-dsDNA, a series of spectroscopic experiments and molecular docking simulations were conducted. The Kb value was found to be 8.85 × 104 M-1 at a temperature of 25 °C by the use of fluorescence spectroscopic techniques. In summary, the utilization of electrochemical and spectroscopic techniques, alongside molecular docking investigations, has led to the prediction that desloratadine has the capability to interact with ct-dsDNA by groove binding.